Project and sequence fps lower than 10 in CS4?

Howdy all - wondering if anyone has discovered a way to work with footage that has a frame rate less than 10 fps in premiere pro cs4? it would be tremendously helpful. I'm doing tutorial recording at work and typically the vids are coming in at 8fps. I've gone as far as trying to hand edit the sequence preset XML and have gotten it to display 8fps, but when I select that preset and open premiere pro, it snaps back to 10fps. seems to be a hard coded minimum. It's not a dealbreaker but just doesn't match my footage at all and makes it so it can't natively exist in my sequence without constant rendering of the timeline.
any ideas?
thanks in advance

If you follow David Brewer's advice and use the DVD preset you will also need to mux the audio in MPEG Streamclip. Compressor's DVD preset assumes you're going to an authoring program with the out put and gives you elementary streams. You need to use both the audio and video elementary stream presets in the Disc Burning folder in your target. Output them to a destination folder. Make sure the mv and AC3 files have the identical names before the extension. Drag the video file into STreamclip and the audio should accompany it as well. Save as MPEG with MP2 audio and the extension will change to MPEG.
I assume it's an SD file. If so, you might be OK with the quality; but it's a very low rate for broadcast.
Good luck.
Russ

Similar Messages

Next value of the sequence is lower than the already used value

Hello All
Recently we have done a test migration of a Database from 10.2.0.4 to 11.2.0.2.
The source database was open during the test migration.
We used Datapump utility for this, first we have created the dump files using the EXPDP and then imported to the target DB using IMPDP.
Now we are facing issues with the SEQUENCE as under mentioned
SELECT Max(RegNr) FROM W23AS.werkProstats;
2058292SELECT W23AS.werkRegNr.NEXTVAL FROM Dual;
2058285As you can see the next value of the sequence is lower than the already used value.
Can anybody point out the reason for this.
NOTE : This particular sequence is defined with NOCACHE option.
CREATE SEQUENCE W23AS.werkRegNr START WITH 2000000 NOCACHE;
Thanks InAdvance
Cheers Tapas

Hi Keith
Please find the details as mentioned below
i) You did not migrate the sequences
We migrated the Sequences too.
ii) you migrated the entire schema but these sequences already existed and therefore were not migrated. (ignore error when object exists ).
These sequences were not existing before.

Volume in multi cam sequences drastically lower than source clips

When I put a multi cam sequence into a new sequence the volume level is drastically lower than on the source clips. Each source clip has 2 mono audio tracks instead of 1 stereo track. Does that make a difference?
Rex

Typically only A1 is used in the multicam cut, so yes the overall volume would be lower than with all audio tracks active.

MacBook not charging. Charging light blinks red and green (very low) than green in normal charge.

My MacBook's battery is dead. When I plug the charge the charging indicator blinks with dim red and green light instead of bright green light. Please help anyone has a solution to it. Last time I remember tye battery was 46%. I plugged in charger and put my iPhone and power bank in charge in Mac USBs. After hours I found that neither phone and power bank was charged nor Mac. Instead Mac's battery was also empty.

Hi harry.ptk,
Welcome to the Apple Support Communities! I understand that you are experiencing issues charging your MacBook Pro. The following resource may provides steps for these sort of issues:
OS X Yosemite: If your battery won’t charge
http://support.apple.com/kb/PH18601
- Reset the battery:
If you have a Mac with a removable battery, remove it and install it again, to make sure it’s properly installed. Refer to the manual that came with your Mac for more information about properly installing the battery.
- Reset the SMC:
Reset the System Management Controller (SMC), which controls how your Mac manages power. For more information, see the Apple Support article Resetting the System Management Controller (SMC).
- Get your Mac serviced:
If the battery still won’t charge, your Mac may need to be serviced. Take your Mac to your local Apple Store or contact AppleCare.
- Matt M.

When I have headphones plugged into my iphone it says warning'' high volume'' and becomes first a red and then plop a number of red pops but it will not be so for someone else I know. My sound will be much lower than anyone else in the music, and when I t

When I have headphones plugged into my iphone it says warning'' high volume'' and becomes first a red and then plop a number of red pops but it will not be so for someone else I know. My sound will be much lower than anyone else in the music, and when I talk by phone headset

Hi! I have the same problem when I use my headphones .
iPhone 4s England, iOS 6.1.2

How should I combine 30 fps clips and 24 fps clips into a project?

I have both 30 fps footage and 24 fps footage and I would like to create a project that has both. Should I create a 30-fps project or a 24-fps project? Which one will look better?

A little bit. Mostly just playing around.
I would start with 30fps so you can preserve the higher frame rate.
Another consideration is how much of your content is 30fps and how much is 24fps.
If you're doing a lot of this kind of thing you may find the FinalCut Pro X handles it better.
Matt
Message was edited by: Matthew Morgan

Hi, Just bought an ipod classic 160gb and i notice that when I turn the volume down all the way, music is still heard, i.e. I cannot turn it down lower than a certain volume. Is there a fix for this? Thanks

Hi, Just bought an ipod classic 160gb and i notice that when I turn the volume down all the way, music is still heard, i.e. I cannot turn it down lower than a certain volume. Is there a fix for this? Thanks

I've got a feeling that's the way it is. I know that if I turn the volume down all the way, I can still hear the music very softly -- which is great for listening when I have a migraine!

Approval with UDF for blank price and lower than standard price

Dear all experts,
would like to know if it is possible for the following 2 events trigger at the same time?
background:
1. a UDF - Standard price retrieve from price list
2. a UDF - blank approval (with selection Yes and No, default is No, it is document level UDF)
3. a UDF - unit price lower than standard price (with selection Yes and No, default is No, it is document level UDF)
Approval event would like to have
1. If the field - Unit Price is blank -> user need to set the UDF "blank approval " to Yes, so can add the document
2. If the field - Unit Price is lower than the field - Standard Price -> user need to set the UDF "unit price lower than standard price to" Yes, so can add the document
i tired the following, but only one of them work when i press the button Add .....
Please kindly help on this.....
Many thanks!!
USE [ANJ_QAS]
GO
/****** Object: StoredProcedure [dbo].[SBO_SP_TransactionNotification]    Script Date: 03/07/2011 00:44:31 ******/
SET ANSI_NULLS ON
GO
SET QUOTED_IDENTIFIER ON
GO
ALTER proc [dbo].[SBO_SP_TransactionNotification]
@object_type nvarchar(25),                     -- SBO Object Type
@transaction_type nchar(1),               -- [A]dd, <u>pdate, [D]elete, [C]ancel, C[L]ose
@num_of_cols_in_key int,
@list_of_key_cols_tab_del nvarchar(255),
@list_of_cols_val_tab_del nvarchar(255)
AS
begin
-- Return values
declare @error int                    -- Result (0 for no error)
declare @error_message nvarchar (200)           -- Error string to be displayed
select @error = 0
select @error_message = N'Ok'
--     ADD     YOUR     CODE     HERE
-- 1. SO with blank price then trigger approval
If @object_type = '17' AND @transaction_type = 'A'
BEGIN
     SET @error_message =
          (SELECT TOP 1 ItemCode + ' (' + CAST(LineNum AS NVARCHAR(5)) + ')' +
               CASE WHEN Price = 0
                         THEN ' Price is blank. Please change UDF - Null Price Approval to "Yes"'
                     ELSE ''
               END
           FROM RDR1 T0
           WHERE DocEntry = @list_of_cols_val_tab_del
               AND 1 = (CASE WHEN (Price * (100 - ISNULL(DiscPrcnt,0)) / 100) = 0 THEN 1
                     ELSE 0 END)
               AND EXISTS (SELECT 1
                              FROM ORDR S0
                              WHERE S0.DocEntry = T0.DocEntry AND ISNULL(S0.U_NullPrice,'N') = 'N') )
     IF ISNULL(@error_message,'') <> ''
     BEGIN
          SET @error = '-10001'
     END
END
-- 2. field price after discount < field rock bottom price for SO, then trigger approval
If @object_type = '17' AND @transaction_type = 'A'
BEGIN
     SET @error_message =
          (SELECT TOP 1 ItemCode + ' (' + CAST(LineNum AS NVARCHAR(5)) + ')' +
               CASE WHEN ISNULL(Price,0) < ISNULL(U_rockprice,0)
                         THEN ' Price:' + CAST(ISNULL(Price,0) AS NVARCHAR(30)) + ' Lower Than Rock Bottom Price: ' + CAST(ISNULL(U_rockprice,0) AS NVARCHAR(30)) + ' Please change UDF - RB Approval to "Yes"'
                     ELSE ''
               END
           FROM RDR1 T0
           WHERE DocEntry = @list_of_cols_val_tab_del
               AND 1 = (CASE WHEN ISNULL(Price,0) * (100 - ISNULL(DiscPrcnt,0)) / 100 < ISNULL(U_rockprice,0) THEN 1
                     ELSE 0 END)
               AND EXISTS (SELECT 1
                              FROM ORDR S0
                              WHERE S0.DocEntry = T0.DocEntry AND ISNULL(S0.U_RBApproval,'No') = 'No') )
     IF ISNULL(@error_message,'') <> ''
     BEGIN
          SET @error = '-10001'
     END
END
-- Select the return values
select @error, @error_message
end
Edited by: tac wong on Mar 14, 2011 6:36 PM

Hi Sachin,
Please create a separate thread for question 2.
With regard to point 1, there is a good description in the SAP help :
http://help.sap.com/saphelp_srm2007/helpdata/en/74/344c430fab4d0bbc30996d56cc293a/frameset.htm
Functions -> Approval Process Frameowrk -> Approval Workflow ->
Approval with Completion
and
Approval
Kind regards,
Siobhan

Macbook air cpu charge is lower than 5%, but temperature is more than 90°C and fans don't speed up ! is it normal ?

hello,
my macbook air cpu charge is lower than 5% (i.e. no apps are loaded only the finder, istat menu give me a cpu charge near 3%),
but temperature is more than 90°C and fans don't speed up !
is it normal ?

It is degrees C.
when the computer has a normal behavour with no CPU charge, its temp is about 35°C
but sometimes temp increase to 90°C and more.
because i don't heard the fan speed increasing (I almost don't heard the fan so i think they should stay at 2000rpm), I'm afraid to burn the CPU and shut down the mac
i didn't let him get hotter.

Recently switched from powermac to mac pro5 2x2.66GHz 6 -core xeon running FCP 7 on OS 10.6.8 exporting qt files and rendering project files now takes longer than my old machine looking at activity mon and % of user is aroun 6 and % of idle around 42

recently switched from powermac to mac pro5 2x2.66GHz 6 -core xeon running FCP 7 on OS 10.6.8 exporting qt files and rendering project files now takes longer than my old machine looking at activity mon and % of user is aroun 6 and % of idle around 42 are all the cores being used with FCP7?

johnnyapplesod wrote:
exporting qt files and rendering project files now takes longer than my old machine
It's because the PowerMac G5 had HUGE bandwidth with a fat BUS on each processsor so they could run hard, hot and heavy.
It's not so with the Intel processors which are multi-core and share a common bus thus bottleneck.
The newer Intel processors can do more work on the CPU, but when it comes to in/out they are s-l-o-w.
I've had a wickedly fast dual processor (not dual core) G5, RAID 0 pair of 10,000 RPM drives as boot and a fast video card, I could do a lot very very fast.
You'll likely have to upgrade to Final Cut X to get more cores utilized, prepare to cry a little bit, Apple is working on the features they stripped out of it to make amends to pro users who complained loudly. (all over TV too)
http://www.loopinsight.com/2011/09/20/apple-releases-major-update-to-final-cut-p ro-x-release-demo-version/

Project in 24 fps want to import 30 and 60 fps without quality problems

I am finishing up a documentary that has taken 7 years. most of the footage is in 24 fps progressive. I have some shot in 30 and 60 fps.
The FCP X project is in 24 fps. I am not finding a way to make the footage smooth. It is either non-interlaced or is pixelated.
I shot it with a DVX100A (good in 2005).
I need help in how to get the 30 and 60 fps looking good in the 24 fps project.
Will I have to render those outside and reimport?
I know FCPX does not need Cinema Tools etc. But from everything I have read, I see no way to import the 30 and 60 into a 24 without quality loss.
Again, my only thought is to litterally render it outside in a different project and then import that render.
Help!!!
-David de Hilster
Long Beach, CA

Ok, I'm sorry, I'm not understanding.
The clips are all 720x480. The project is bigger but all clips import to the correct "adjusted" size.
Is there a place I have to put the 480 => 720 setting? Isn't it the case if they are appearing in the correct size (meaning the top of and bottoms of the 30fps are at the top and bottom of the 720 size), then they are already set correctly?
Is there something else I have to set to get the quality to the best it can be?
Again, 24 fps are in fine quality, in the corrected size.
-David

Apple ask me a proof of purchase of my macbook for activate my AppleCare Protect Plan, but even if it's a JPEG lower than 5 mo, it told me that it's not «good» and I can't send them my proof... so I can't activate my AppleCare protec Plan. What can I do?

Apple ask me a proof of purchase of my macbook for activate my AppleCare Protection Plan, but even if it's a JPEG lower than 5 mo, it told me that it's not «good» (in french: le format de ce fichier n’est pas valide.) and I can't send them my proof... so I can't activate my AppleCare protec Plan. What can I do?

Call the Apple support line, ask for AppleCare Plan Administration, and get a fax number and fax a copy of the receipt to them.
Regards.

Big Problem with Directx 11 and Games scaling when lower than native resolution

Hi Guys,
MY system is Windows 7 Home Premium (Korean version), and I have dual GPUs, Nvidia Geforce GT 630m for gaming, and Intel HD Graphics 4000 for all other display matters. My native resolution is 1920 x 1080.
This problem wasn't there couple of years back, but from 2~3 years ago, when I play recent games that require/favour directx 11 (such as Assassin's Creed IV Black Flag, Batman: Arkham Origins), it seems when I use lower than native resolution (such as 1280
x 720) and select fullscreen, giant ugly black borders always appear around the game, and the game does not fill the whole screen.
I thought this was something which could be fixed in my GPU's control panel, but there was no scale fullscreen option under Nvidia's control panel. So I went into Intel HD Graphics control panel, but there was no Scale fullscreen option there either (under
native resolution. With lower resolution there was).
Anyway, after months and months of searching, I finally found an Intel forum which was discussing the same situation:
https://communities.intel.com/thread/44539
While going through the forum, I found out from other users that problem is not with GPU's drivers, but with Directx 11.
To test this theory, I put Batman: Arkham Origins in Force Directx 9 mode, and changed the game resolution to 1280x720. And the game showed no black borders, it scaled up perfectly to fullscreen under Directx 9 (so no problem whatsoever under directx
9). I changed the setting to Directx 11, and the ugly black borders appeared again.
Could someone please help with this? I know I can change my screen's resolution every time I play the game, but it's a real nuisance to do that. And more games are utilising Directx 11 or higher, and I don't think there are many games where I can
force Directx 9 mode like I did for Arkham Origins.
Or if someone connected could contact the people working on Directx 11 and ask about this issue (and get them to contact me through my email below), that would be much appreciated.
my email:
[email protected]
p.s. : all my GPU drivers are currently up to date, and the black borders issue is still there

Hello MeipoXu
While yes, at first people on the Intel forum thought it was the display driver problem (hence the question was originally posted on the Intel forum). But if you look closely through the pages especially Pages 2 onwards, there are some very astute
comments by some posters:
Update to black borders problem: The problem is DirectX11. Fx. Company of Heroes has a setting "Shader Quality" that when set to ULTRA it will run directX11 and when set below ULTRA it will run directX9. So the intel graphics driver is not
responsible! It is Microsofts DirectX11 that does it - maybe only to computers with both Intel HD and a second graphics card for video games
Different workarounds to the black border problem:
Change resolution before running fullscreen
Use directX9 instead of directX11
Fx. in CoH2 there is a setting fx. 50% of resolution, so even in native resolution the graphics is only half and thus faster
Try window mode without borders
and here's also another:
I can confirm that this problem still seems to exist, and that it definitely seems to be related to DirectX 11.
In a variety of games, turning DirectX11 off (either in-game or using ini files in some games that don't present you with the choice) fixes the issue. But this is obviously not ideal.
I have a laptop with a native resolution of 1920x1080, but tend to run games at 1280x720 because it provides much better performance on my HD 4400 graphics chip. This bug and the memory leak issue on Windows 8.1 are extremely annoying.
Like the first poster, my PC has intel HD GPU, and a second graphics card for games (Nvidia).
And all the members have mentioned that they updated the intel graphics driver, but it does not fix it - so it doesn't seem like a graphics driver problem (and more to do with Directx 11).
And they are right. With Batman Arkham Origins, if I set the resolution to 1366 x 768 and apply fullscreen, under Directx 11, ugly black borders appears. Luckily Arkham Origins has "Force Directx 9 mode" which I use, but a lot of games
don't have this mode (such as ACIV Black Flag, Watch Dogs, Sleeping Dogs etc) - you either play in ugly black borders, or can't play the game at all.
And all my Graphics Drivers are currently up-to-date, and issue still exists, so I don't think it's the driver problem.
I have already tried that registry method you just mentioned. It didn't work.
As for Directx 12, well I just hope it works better than Directx 11 (with its ugly black borders in games) does, and works well like Directx9 (with no problem in scaling).

I have low C disk space. Want to install Ai Trial. Not enough Space. But have a huge space of G: drive. How I can direct install to download and install on other than C: drive?

I am short with C: Drive space. Cannont Install Ai Trial. How I can download and Install on other than C: drive? I am trying to download it through Creative Cloud as a subscriber.

Thanks for help. It worked. Now up and running Ai.
Sent by:
Khalid Hameed
London - UK

Trying to make a dvd from a project and this error message appears .The project could not be prepared for publishing because an error occurred. (-2125)

Trying to make a dvd from a project and this error message appears .The project could not be prepared for publishing because an error occurred. (-2125)

Hi
Error -2125
OK Error code - 2125 usually indicates that the movie is to large.
It use to pop up when going to iDVD !
iDVD - DO NOT CARE ABOUT Gbs at all. I got movies on 500Mb that do not fit and 50Gb that fits nicely.
iDVD - ONLY CARES ABOUT - Duration. Duration is Movie time + MENU TIME. Choice of
menu and animation of this can take lost of "DURATION" 15 minutes or even more.
Choice of encoding method and use of SL or DL DVDs determine the DVD limit.
iDVD 08 & 09 & 11 has three levels of qualities.
iDVD 6 has the two last ones
• Professional Quality (movies + menus up to 120 min.) - BEST
• Best Performances (movies + menus less than 60 min.) - High quality on final DVD
• High Quality (in iDVD08 or 09) / Best Quality (in iDVD6) (movies + menus up to 120 min.) - slightly lower quality than above
DL DVDs can store about double of these times.
ALTERNATIVE - The Error Code can indicate that free space on Start-up (BOOT) hard disk is
less than 25Gb (my minimum)
calbe - wrote
If you are getting OSStatus error -2125, I've seen this caused by the computer display sleep settings.
Try changing the sleep settings to never and see if you are able to export.
Yours Bengt W

Project and sequence fps lower than 10 in CS4?

Similar Messages

Maybe you are looking for