Project cannot render again due to disk drive name change

Recently I installed a new motherboard and processor. When I came back up my drives all have different labels, except for the C: drive. My encore project which rendered successfully before now gets this error in the middle of rendering and burning to bluray.
Blu-ray Error "device not ready", code: "3", note: "File cannot open. (G:\encorework\sequence 9-10-11\AuthorScriptHDMVSessions\Silence.ac3.11_29_50_18.3.2010_UTC_04_00DST.ves) - ERROR: Error locating.
The new drive is M and no longer G. When I go into encore and check the project all looks well. What file is still looking on G: ?

Hi,
Remove the files from \AuthorScriptHDMVSessions folder and try again.
or
you can save as your project and try again.
Thanks,
Pankaj Gauba

Similar Messages

Macbook pro with retina display cannot read a mobile hard disk drive

My macbook pro with retina display cannot read a mobile hard disk drive but can be read on macbook(the white one). What should i do to solve that problem?

Thanks wjosten.
Makes perfect sense. Guess I will have to hurry up and setup my new MBP with retina display.
Better get started.
Thanks for your help

Directory cannot be rebuilt due to Disk hardware failure (-36, 2286 )

Hello everybody,
my macbook was running slower and slower until it became unusable.
I have restarted the macbook with system DVD and run harddisk utilities from the DVD :
- First diagnostic : directory damaged, error on knot, cannot be repaired by this program.
I tried to put the disk in target mode but it was impossible to mount it on the desk.
-Then I tried with DiskWarrior utilities and got the message : Directory cannot be rebuilt due to Disk hardware failure (-36, 2286 )
Does anybody knows what it means ?
If disk has to be changed what brand would be the best suited.
Any advice on this issue will be more than welcome
Best regards from France
Jean Claude

*Many thanks* Templeton Peck for your help.
I am going to replace the disk but all the work of the last four days will be lost, kinf of hard to swallow on a machine bought a little more than a year ago !
Sweet home Chicago ! 41 years ago I heard Menphis Slim sing that tune in "Les trois maillets" a famous St. Germain des prés jazz club in Paris. Souvenirs, souvenirs…
Message was edited by: HotDna

Cannot sign on due to "Disk I/O error"

I cannot sign on due to Disk I/O error. I followed wht Skype recommends: Deleted my user folder under C:\Users\<myname>\AppData\Roaming twice, does not help.
What else can I do?
Would reinstalling help?
Solved!
Go to Solution.
Attachments:
SKYPE_ERR.jpg ‏58 KB

that does not sound good to me, the message is that the disk is stuffing up, in that skype can not read information from it, at leat that is how I read it, I would suggest you use a program that comes if a free cut down version http://www.hdsentinel.com/ it was so good I paid for it, not expensive and does not expire, so the key lasts as long as the company keeps updating, not like MS windows where you have to pay and pay, or ithis one may be good but I have not tried it but it is free http://download.cnet.com/HDD-Health/3000-2086_4-10804806.html
another thing to also do is is check the hard disk sectors with something I would recomend http://www.partition-tool.com/ which has a free version with all the tools you want.
ray

Any idea why my desktop drive name changed to '\

Hi.
Just sat down to do some work for the first time in two days and noticed that an external drive on my iMac and a desktop folder have had their names changed. The drive changed to '\ and the folder changed to \
I found my 3-year-old noodling on the keyboard for a few seconds earlier in the day, but don't think that's it. The two new names seem ominously similar and suspicious. The folder was no problem -- I just created a new folder with the old name, copied my files to it, and then trashed the one with the changed name. The hard drive will not let me change its name, however. I can click on the name field, but when I start typing, it tabs to the next item on the desktop.
I restarted, ran Disk Utility to verify the drive in question, and repaired permissions on the internal drive. I do think I have one tiny bad spot on this external disk, but it's been working fine otherwise and I have it backed up. But regardless, this wouldn't explain why a totally unrelated folder on my desktop suffered a similar fate.
Any ideas what caused this, whether I can change the name back, or if it's going to cause problems down the line if I can't?
Thank you.

Do you have children or a cat? I found the same thing after my grandson visited not long after he reached the "mobile" stage. A few minutes banging on teh keyboard of my wife's iMac left the hard drive with an odd character for a name.
Cats are more computer-literate that many people think. When they walk across the keyboard, they seem to know exactly the right keystrokes to make you computer do odd things--if you are lucky. If you are not lucky, cats know how to leave remnants of meals past of worse on a keyboard.

Hard Drive name changed on it's own.

Hi there.
On starting my Mac Mini this morning I noticed that the hard drive name had changed from "Mac HD" to "/" without any input from myself.
does anyone have an idea what may have occured ?
Thank's.

Try using GrandPerspective to see what's taking up all the space.
Also, make sure everything you don't need is turned off under Sharing; it's possible that you left file sharing on without a password and someone is taking advantage of that.
If you have a MobileMe account, do you have iDisk Syncing turned on? Or something similar if you have Dropbox or another similar service?

Cannot duplicate event due to same file name

I'm trying to archive some video projects my boss has made using Final Cut Pro X 10.0.7 on OS X 10.7.5. The problem I'm having is that I cannot "Duplicate Project + Used Clips" like I have done in the past because this project uses clips from three different events, and each of these events contains files that happen to have the same names as files in the other events.
For example:
Event A
- 00000-1.m4v
- 00000-2.m4v
- 00000-3.m4v
Event B
- 00000-1.m4v
Event C
- 00000-1.m4v
- 00000-2.m4v
So let's say the project he's created uses all these clips. If I attempt to "Duplicate Project + Used Clips", it won't work because 00000-1.m4v from three different events is used in the project. Apparently FCP is written in such a way that it allows you to fall into this trap. What it should be doing is either not allowing you to import a file into an event if that file name already exists in another event, or it should be smart enough to rename duplicate files on-the-fly when exporting (for example, 00000-1-1.m4v and 00000-1-2.m4v). But it does neither of these things.
The problem here is that these are the three events:
Event A = 108 clips
Event B = 68 clips
Event C = 80 clips
All FCP will say is that "two or more media files use the same name - rename the file or files and try again". Only it's not talking about the name of the file from within FCP -- it only cares about the file name as seen in the Finder. So even if I went into event A and put "A-" in front of all the clilp names, it doesn't matter, because it's not really "A-00000-1.m4v" -- the file is still named "00000-1.m4v" in the Finder, and the problem is unresolved.
Does anyone know any way of sorting out this problem without a massive amount of digging around, renaming files by hand and relinking?

I'm still stuck on this problem and in a couple of days I'm going to be sitting in on a webinar that will discuss archiving in FCP X.
I have tried several things and if I'm missing something I'd like someone to let me know. I also cannot find much on this subject which is very surprising...or I'm not searching in the right places. I'm going to submit feedback to Apple as follows:
Error: “The operation cannot be completed. Two or more media files use the same name. Rename the file or files and try again.”
Operation attempted: Duplicate project with used clips.
Second operation attempted: Consolidate project media > Copy used clips only.
Cause: Two or more events contain clips with the same name.
Eg.
event-20130126
          GOPR0002.mp4
event-20130220
          GOPR0002.mp4
Background:
          This video project resulted in a one hour documentary that used recordings from 6 different cameras shot over a span of 4 months. Each day’s recording, for the most part, was broken into separate fcp events. This resulted in 48 events.
          AVCHD imports result in media files whose name reflects the date and time of the recording which makes each of the imports’ media file names unique, even across all events.
          Imports from cameras such as GoPro’s Hero use their own original file names such as GOPR0001. Therefore media file names are not unique across all events.
          Due to render and export problems, the video was broken up into 14 separate FCP X projects, aligned with what would ultimately be a “chapter” in the resulting video.
          The 14 projects “share” events; i.e. the events used in the 14 projects (chapters) are not mutually exclusive.
          The source media as well as the events span over 3 physical external hard drives.
          All 14 projects are on one hard drive.
Consideration #1:
          It would seem that one way around this problem is to merge all 48 events. I will not do this since this function moves the events rather than copies them. Additionally, I’m not even sure if I have enough space to consolidate all 48 events anywhere available to me.
Consideration #2:
          This leaves only one other option which is to rename the source media files and relink all of them across all events.
Questions:
          1.          Why can’t FCP (internally) qualify the media file names that it imports with the event name? i.e why is it left up to the user to insure that all of the media file names are unique across all events used by a project?
          2.          If it doesn’t do #1, then why were we not warned of this before starting. I find out about this when I’m done with my project and trying to archive. Now it’s a huge task to rename and relink.
Thoughts:
          Regardless of whether there is work-around to this problem, the fact that FCP has a “feature” such as events and allows projects to use more than one event but does not manage them properly reveals a weakness and flaw. If such is the case, then it would be less painful, in this situation, to force a project to use only one event.
I wish that others would speak to this problem. Or let us know what the answer to this is.
Thanks.

Cannot access my second internal hard drive after changing permissions

Changed the permissions by mistake on the second internal hard drive and now windows 7 cannot see it. Going to My Computer Icon, ?>>> Manage >> Disk Management and Try to initialize it but i get the incorrect function error.
How can i get back access to my hard drive.?

Hi Alex,
What is your current situation?
You may check if you could manage the disk through diskpart:
A Description of the Diskpart Command-Line Utility
Under diskpart, enter the following line:
List disk
As Frederik suggested, please check the disk health first.
Best regards
Michael Shao
TechNet Community Support

Dom0 Disk Device Name Changed... how to rename in vdsdev?

Good Morning,
We had a server "incident" yesterday that left our Solaris ldom host rebooted. When it came back up, one of our guests (ldg1) refuses to bind with the error:
Path /dev/rdsk/emcpower3c is not valid on service domain primary
Sure enough, the emcpower3a device doesn't have a slice 2 (c) any more. My guess is since emcpower3c was presented to the guest as a full disk and the guest used the full disk (without slicing/partitioning it up) as part of a ZFS pool, ZFS overwrote the partition definition, leaving just the emcpower3a device usable.
Now the question is... how do I update the reference in ldm to change the VDS volume device from emcpower3c to emcpower3a? If I drop and recreate the volume, it could end up renaming the device in the ldg1, couldn't it? While I'm sure I could resolve that with ZFS, I'd rather not if I can avoid it. :-)
Any thoughts?
Thanks!
Rob

"Macintosh HD" is the name of the drive inside the mac, not the name of the Mac.
To properly change the name of the Mac, go to System Preferences --> Sharing. There is a field to enter the name of the Mac.

IMac disk driver error cannot repair or try again.

I put my blank disk into my iMac and it gave me my usual set of options. Moving into my Itunes account, I tried burning my playlist to the disk which it accepted. After a while of whirring and working still in the initializing disk burning phase, it simply stopped running. The disk burning initializing bar kept saying it was loading but nothing was goig on. After about five minutes it went to disc burn finishing loading bar without having loaded anything onto the disk. The bar stayed there for a while until i got a message saying that "the disk could not be burned due to a medium write error" and the disk was ejected. This is the third time this has happened. Another time i had tried and an error message popped up telling me that "The disk could not write because of a disk driver error" it also told me it could not repair and I should not try again. If anyone can help, I need to know how to fix this problem and what is wrong with it in the first place. Thank you.

HI,
Try this... boot from your install disc again.
Insert your install disk and Restart, holding down the "C" key until grey Apple appears.
Go to Installer menu and launch Disk Utility.
Select your HDD (manufacturer ID) in the left panel.
Select First Aid in the Main panel.
(Check S.M.A.R.T Status of HDD at the bottom of right panel. It should say: Verified)
Click Repair Disk on the bottom right.
If DU reports disk does not need repairs quit DU and restart.
*If DU reports errors Repair again and again until DU reports disk is repaired.*
When you are finished with DU, from the Menu Bar, select Utilities/Startup Manager.
Select your start up disk and click Restart
Perhaps another pass will do the job. Worth a try....
Carolyn

FF_5 import couldnt be done, due to "File in disk drive cannot be opened"

Hello everybody,
we made an upgrade from SAP 4.6C to ECC6. After some configuration we installed and addon which lets us to import BANK statement while using standard SAP TC. FF_5.
But we face a problem.
We start by converting our BANK file with DME engine.
Then we try to import it via FF_5 but then we get following error: File X in disk drive X cannot be opened, Message no. FB704, where x stands for "space"
our Bank import file is equal to the format described in DMEE TC eversy single line matches exact.
Points in regard
Thanks
Laurynas Prikockis

Hi Laurynas, we are running the same migration process as you mentioned and have the same problem with the FF_5 transaction.
Have you figure out something to correct this problem?..
Thank you in advance

"The iPhone cannot be synced. The disk could not be read from or written to." Any clue what that is due to. Everything but photos seem to sync fine.

when syncing, I get an error message stating: "The iPhone cannot be synced. The disk could not be read from or written to." Any clue what that is due to. Everything but photos seem to sync fine.

I had the same problem when trying to sync my new ilPhone 4s and a fairly new iPad 2. I couldn't find anything in the forum about it. So, since my 4s was new, I called support and luckily I got a CSR with some knowledge. He at first thought it would be tough to fix but after thinking a minute he found the fix. The fix is:
Click on finder, Go, Home, Pictures, then click on iPod photo cache and drag it to trash. Now try syncing again. It worked on both of mine. No problems since.

No more optical drive and windows 8 issue: "Windows cannot be installed on this disk as it has an MBR partition table."

I have an Early 2011 13" MBP going strong with an SSD and original HDD installed in the optical drive. However, having had success with windows 7 on my old HDD I was planning to install Windows 8.1 (from .iso) on my SSD. However, for the past day or so it's been a nightmare.
I tried the official procedure but by editing the bootcamp info.plist so I could boot from USB (you can't install windows from an external optical drive apparently) partitioning as bootcamp wanted too.
I then tried it a number of different ways using disk utility etc and with an empty space
However, I always seem to end up with the error "“Windows cannot be installed on this disk. The selected disk has an MBR partition table. On EFI systems, Windows can only installed on GPT disks“
I read some interesting stuff here http://www.royhochstenbach.com/installing-windows-8-1-on-a-2013-mac-pro/
He points out that
"Windows 7 and 8 in x64 support EFI. Normally if you install Windows on a Mac and use the installation DVD, it boots into regular BIOS mode, thus can be installed on an MBR partition. I tried the same, but since the Mac Pro doesn’t have an optical drive I had to use an external drive. And apparently the Mac boots external optical drives in EFI mode too. The Bootcamp wizard is aware of this, and creates a GPT partition on a non-superdrive Mac but an MBR partition on a superdrive Mac."
This means Bootcamp is essentially making the wrong type of partition?
My real question is? How do I install it windows 8? I'm really on my last legs!
I really don't want to have to open this thing up and reinsert my optical drive as its really really difficult to get out of the enclosure (would probably have to break it).
A huge thanks in advance!

Hi,
Have you tried that suggestion?
You also could use this commands to check and install again:
Inside windows installer, hit Shift+F10 to get a command prompt, then run diskpart and type List disk to displays a list of disks and information about them, such as their size, amount of available free space, whether the disk is a basic or dynamic disk,
and whether the disk uses the master boot record (MBR) or GUID partition table (GPT) partition style.
and then select the target disk. Zap the drive (with the clean command), create GPT table (new gpt), create the GPT-EFI special partitions.
Step-by-step instructions is here for reference:
HOW TO: Use the Diskpart.efi Utility to Create a GUID Partition Table Partition on a Raw Disk in Windows
http://support.microsoft.com/kb/297800?wa=wsignin1.0
Then reboot so the firmware finds those partitions and adds the disk to the EFI-native boot order (Windows installer checks this).
Karen Hu
TechNet Community Support

PE 13 crashes due to incompatible video driver detected. Running on Win 7 SP1 with ATI 540v video card/driver. Deleting bad driver file in adobe program data does not fix the problem, it simply replaces the text file and crashes again. My video driver

PE 13 crashes due to incompatible video driver detected. Running on Win 7 SP1 with ATI 540v video card/driver. Deleting bad driver file in adobe program data does not fix the problem, it simply replaces the text file and crashes again. My video driver is just fine. Any help out there?

rb
Your video card driver may be fine for something, but just not compatible with Premiere Elements 13/13.1.
For those with the display card error, the answers include
a. assure your video card/graphics card driver version is up to date according to the web site of the manufacturer of the card -
if necessary consider a driver roll back.
b. determine in Device Manager/Display Adapters if the computer is using 2 cards instead of 1
c. delete the BadDrivers.txt file
the rationale for that deletion is found in post 10 of the following older post...principle applies to 13 as well as 9.
Re: Premiere Elements 9 Tryout Serious Display Problem
Have you looked for computer ATI card settings that might be more compatible with Premiere Elements 13/13.1?
When is the program crashing - just opening a new project or rather crashing if editing a particular video format at the Timeline level?
ATR

Trying to back up iPad to external hard drive, "iTunes library file cannot be saved. The disk you are attempting to use is full."

This issue is somewhat complex so I will try to explain it as clearly as I can. Any help will be greatly appreciated.
It all began when I kept getting popups from my iPad saying that I had not backed up since May. I realized that was pretty dangerous so I decided to finally try syncing it to iTunes, though I had avoided doing so for so long because I knew that when I tried there was no room on the computer. I then remembered that I have an external hard drive with plenty of storage space, so I got that out and set it up with a folder to move iTunes and the backup into.
On iTunes I went to the Advanced Preferences and changed iTunes Media Folder Location to the G: folder, with the keep organized box checked. I also copied the previous backups from the original C: drive to G: so that I could delete the ones on C:.
I used Junction Link Magic to link my now empty MobileSync backup on C: to a new (JLM would not work unless it was empty) backup folder on external hard drive G:.
I plugged in my iPad to iTunes to sync it, and while it was backing up I checked the new folder on G: to make sure that the backup was being put there. It was.
However, about halfway through I got the message "iTunes library file cannot be saved. The disk you are attempting to use is full."
My question is Why? If it is being made in a 1.5 terabyte hard drive now, and not the computer, why is there no disk space? My guess is that it must still somehow be saving to the computer. But how? And how can I get it to save solely on the G: drive where there is enough room?
I am running Windows XP and the latest version of iTunes.
An additional but not as crucial issue:
Much of my music has been lost, with the being displayed next to the songs in the iTunes library, and only 50 (purchased) songs remain on my iPad. This was because those missing songs were stored on a different external hard drive ( I:). However, I copied many of the music folders on I: over to G: so that everything could be together. I am wondering if it is possible for me to get these songs back onto my iPad. But this is not my most important issue right now, because I believe that once I get the first issue solved I can simply plug in I: and G: at the same time while syncing the iPad, and get the songs back.
Note: I have come to realize the iTunes program itself is still under Program Files in the C: drive. Does this have to do with anything?

Short term, free up some disk space. Long term, move the library to a bigger drive.
tt2

Project cannot render again due to disk drive name change

Similar Messages

Maybe you are looking for