Projector killed hard drive under newly installed yosemite??

hey folks!
i connected my macbook pro (mid 2012, non-retina) to a projector today and as i did that everything froze. i disconnected the projector, but no change. i forced a reboot and got a light grey screen with a blinking folder and question mark. it turns out my internal hard drive is dead.
i updated to yosemite last week and have had smaller issus since then when connecting to a projector (black space where the keynote window was before which only vanished with a reboot).
can anyone tell me, whether my hard drive dying has anything to do with the update to yosemite (my warranty ran out 2 weeks ago)? anyone with similar problems?
thanks!

minopilus wrote:
can anyone tell me, whether my hard drive dying has anything to do with the update to yosemite (my warranty ran out 2 weeks ago)?
I think it is very unlikely that the two are connected.
It is more likely (though not certain) that something weird happened when plugged into the projector. Like a bad cable or a bad port that maybe allowed some kind of power surge back into the motherboard that might have affected the hard drive. But let me emphasize...this is a very unusual problem that should not have happened. Thousands of Mac laptops are plugged into projectors every single day in corporations and schools and universities. It is not a problem that should be expected to happen.
Also, dying hard drives have not been reported by the thousands of Mac users who have also done the Yosemite upgrades. I have two Macs that upgraded to Yosemite without a problem.
I don't know what the real cause was, but chances are it was a fluke. One possibility: The hard drive was already having undiagnosed problems, and this just pushed it over the edge.

Similar Messages

  • Can I switch out a hard drive for an SSD without having to clone the existing hard drive, and then install Yosemite from an USB Boot Drive onto the new SSD?

    Can I simply replace a hard drive with a new SSD and just install Yosemite from a USB boot drive onto the SSD? I recently bought a used MBP and it has absolutely no files on it except for the OS, and so I'm assuming I don't need to clone the current hard drive as I can just reinstall the OS onto the new SSD.

    Honey_Revenge wrote:
    Thanks.
    Just a quick follow up question, is formatting the SSD with HFS+ done in Disk Utility?...
    It's possible that the SSD will be set up for use on a PC, which means it will have a Master Boot Record partition table rather than a GUID Partition Table, which is what Yosemite needs. In Disk Utility, select the SSD and click the Partition button. Create a new Partition Layout and click the Options... button at the bottom. You'll likely see MBR is selected. Choose GUID instead and Mac OS Extended (Journaled) for the Format.

  • New Internal Hard Drive and Clean Install: Errors, Frustration and Hopelessness

    First Off:
    Macbook 13" (late 2009) ... It was running Mountain Lion 10.8.5 with 2 gigs of memory and 160gig stock hard drive.
    I started this process almost a week ago and despite numerous attempts every night I have had no luck. I appologize if the details here are fuzzy, my head is spinning after reading dozens of threads and attempting multiple solutions to each error I've received and i cant remember everything I've tried so far...
    I got my new memory in the mail first, upgraded to 4 gigs and everything works fine with that..
    Next came my new Seagate Momentus 750 gb 7200 rpm SATA 3gb/s 16Mb Internal Hard Drive.
    Using this guide: http://osxdaily.com/2012/02/17/make-bootable-os-x-10-8-mountain-lion-usb-install -drive/ (and cross checking other guides) I ended up creating a bootable external drive using my 160gb External Firewire drive for my clean install to my new hard drive. So far so good.
    I then shut down the computer, removed the old internal hard drive, installed the new, restarted the computer holding option key and booted up using the External Hard Drive, and the install software started fine. Note: I have attempted to re-erase the drive so many times without luck that I cant remember if I actually successfully erased the drive originally to begin with the installation, but either way I started the OSX reinstall and it got almost all the way finished before it gave me the error message:
    "Install failed. Mac OS X Lion couldn’t be installed, because the disk (volume name) is damaged and can’t be repaired. Click restart to restart your computer and try installing again."
    restarting of course did nothing, it repeatedly gave me error messages and made me quit installation...
    Disk Utility isnt getting me anywhere, im either getting errors like:
    "POSIX reports: the operation couldnt be completed. device no configured"
    it wont allow me to erase the drive or partition the drive
    "Disk Erase failed with the error: File System Formatter Failed"
    and everytime the drive fails to erase or partition, it disappears from the list of drives on the left of the disk utility screen and i have to restart the computer for it to reappear for a second try. Typically the volume under the drive is greyed out and says that it is unmounted.
    Ive zapped the PRAM.... and Ive done other things that I cant quite remember right now because my brain is boiling from reading too many **** threads on multiple devices....
    halp.
    halp me plase.

    So funny story...
    While writing this discussion I had to come to the computer and try to erase the drive so I could see the error code for reference. The erase didnt work as usual but I wrote the error code down here.
    I also could not remember the error code for partitioning the drive so I attempted that as well so I could write down the code, and this time it magically partitioned successfully! The only thing I did differently was that I didn't rename the partition because i figured it wouldn't matter anyway. Since the partition was successful, I attempted the Reinstall of ML and it magically worked!!
    I dont know what the **** happened but ive been attempting this install every night for like 3 hours since Monday and this is the first time it went through... for no apparent reason?
    Ghosts? Magic? Full Moon?
    we may never know...
    Thanks anyways guys!

  • New Mac Mini Server, two Hard drives, Can I install an older Mac OS on the second drive and switch start up disks to run PowerPc applications?

    New Mac Mini Server, has two Hard drives, could I install an older Mac OS on the second drive and switch start up disks to run PowerPc applications?

    I haven't purchased a Mac Mini at this time and I may not if I can't use it as a non server. I need to update my system I would be better off buying a new Mac with Snow Leopard the last app that will run Rosetta. The Mac Mini Server has a quad 2.0 processor and 4 GB RAM and two internal hard drives and should out perform my dual 1.25 G4. I can run PPC apps on my G4 but it is 8+ years old and seems to be getting noisy. I don't want to tie myself to another old machine. I want a machine that will work with Intel Apps I was hoping that the two hard drives would allow me to boot from the second with Snow Leopard and use Lion on the first drive to be able to keep up to date with all my other universal apps and Mac OS up grades. The application I use the most is my CanvasX app with drawing & vector effects, text & typography, sprite technology, painting, image editing, and multimedia tools are all in this one app but will not be updated to run Intel apps. I am frozen in time because my most valuable Application won't be updated and Apple has cut me off by not supporting PPC in Lion and onward; Apple used to backward support but I guess that they are no longer as user friendly and concerned with a happy user. I have always been a loyal Mac user and I will not migrate to Windows under any circumstance; I hate windows!
    Thanks for your prompt response,
    Dick Deaton

  • How large of a hard drive can I install on dual G5, and do I need more RAM?

    I recently had a situation in which my dual-processor 2.0 G5 was completely refurbished by Apple repair-new logic board, both processors, video card, thermistor, all new. Finally it has been working well after a month of trips back and forth from the Apple store. I have two internal hard drives installed on my G5, both 300GB, one for OS applications, and one for audio. I am running out of space on my main hard drive, and so I recently purchased a Maxtor 1TB hard drive, now manufactured by Seagate, from Fry's. After having my G5 refurbished, I was having an issue with my Samsung 930B monitor going into sleep mode when I boot-up from a CD, but other than that G5 was working fine. I removed the main 300GB hard drive from slot #1 and put it into slot #2, from which I had removed my audio hard drive. I installed the Maxtor drive in slot #1 and reformatted it for Mac using my laptop with ATA/USB cables previously purchased for data transfer. This took about 14 hours as I used the "zeros" option. After that I hooked up the internal cables to both drives and tried to boot up from Leopard in order to install it on the Maxtor drive, but again my monitor went into to sleep mode. We went to the Apple store to try to see if there was an issue with the computer, but everything worked fine with their monitors and CD's, as well as my CD. So there is some kind of issue with my monitor, probably software as it works fine when booting up from the main hard drive, and also was fine when I did its self-test function. While at the Apple store, they installed Leopard from their hard drive which took about 30 minutes.
    My problem is this: When I arrived home, I turned on my G5, which had been set to boot from my new Maxtor drive and complete the Leopard setup process, which we had decided to do at home as it would have taken another 20 minutes in the Apple store. The G5 turned on, chimed, I got the Apple screen with the wheel, but then after that my monitor goes into sleep mode. I can hear Leopard's setup intro playing through the speakers, but the screen is in sleep mode. So I reboot holding down the option key so I can boot up from my old (300GB) main hard drive, now in slot #2. This works and the monitor screen does not go to sleep. However, as I am browsing on the web to check for issues concerning this monitor, the G5 freezes, and I get a screen with black bars with writing in them and various technical language across the screen. This happened several times after rebooting. Finally I shut the computer down. I am going to try removing the new hard drive and putting both old ones back in and see if the G5 stops crashing. I think the monitor issue is a separate issue, and I am more concerned with the crashing, as previous to the new hard drive installation the G5 was working fine, monitor fine, other than the issue when booting up from a CD. Do I need more memory? Is the 1TB hard drive too large for my dual-processor 2.0 G5 and overloading it? Would I be better off with a 500GB drive? Would appreciate advice from persons with experience in this area. Thank you.

    I have replaced my 5 year old G5 with a Mac Pro, as the G5 just had too many issues, even after replacing all major components (logic board, both processors, video card, etc.) Once I took out the 1 TB hard drive from my old G5, it stopped having the kernel panic issue. Nonetheless I had been through a lengthy repair process previous to this issue, so I didn't care to trust an older machine any longer, especially since being told by an Apple tech that the "new" parts were really just older parts stockpiled from a central location. Could be new, could be refurbished. Apple was kind enough to credit the money we had spent on the G5 repairs towards the purchase of my Mac Pro.

  • How many hard drives can i install in my mac pro

    How do I know what size hard drives I can install?  I currently have 4 x 2TB drives installed and am looking to go bigger.  4 x 4TB would be ideal and if you have suggestions on which drives might give me best performance for HD video editing that would be nice too.
    Also can I install more RAM? 
    ere is some information to help. 
    Mac Pro
    Early 2008
    Processor  2 x 2.8 GHz Quad-Core Intel Xeon
    Memory  16 GB 800 MHz DDR2 FB-DIMM
    Graphics  2 x NVIDIA GeForce GT 120 512 MB
    Software  Mac OS X Lion 10.7.3 (11D50b)
      Model Name:          Mac Pro
      Model Identifier:          MacPro3,1
      Processor Name:          Quad-Core Intel Xeon
      Processor Speed:          2.8 GHz
      Number of Processors:          2
      Total Number of Cores:          8
      L2 Cache (per Processor):          12 MB
      Memory:          16 GB
      Bus Speed:          1.6 GHz
      Boot ROM Version:          MP31.006C.B05
      SMC Version (system):          1.25f4
      Serial Number (system):          G************
      Hardware UUID:          47DF4954-C493-50B8-85F3-FC381FA75AD6

    PCIe SSD controller
    www.macperformanceguide.com
    That would be $1600 for your 16TB
    There are kits to put 2.5" drives (4) in lower optical drive bay. Some WD 10K VR 500GB and 1TB ($200 and $300, 200MB/sec)
    32GB 8 x 4GB FBDIMM 800MHz
    GTX 570 w/ 10.7.3 from MacVidCards

  • How do i use airport as both time machine and hard drive? currently on Yosemite 10.10.1

    how do i use my 3TB airport time capsule as both time machine and hard drive? currently on Yosemite 10.10.1.....Many Thanks.

    Choose Computer from the Finder's Go menu and double-click it. If needed, use the Connect to Server command to log into it.
    (119763)

  • I want to upgrade my Hard Drive to 1TB and more.  What is the maximun Hard Drive I can install for a MacBook Pro 2009 Yesterday, I tried a SEAGATE SSHD but my screen was always a showing a QUESTION MARK (?). It's not the cable because when I put back

    I want to upgrade my Hard Drive to 1TB and more.
    What is the maximun Hard Drive I can install for a MacBook Pro 2009
    Yesterday, I tried a SEAGATE SSHD but my screen was always a showing a QUESTION MARK (?). It's not the cable because when I put back the old original version, everything works...Any sugestion of brabnding or procédure to upgrade my hard drive?

    The largest 2.5" dia SATA drives available are 2 TB in capacity.
    Have you tried the Seagate SSHD connected externally to the MBP via USB?  The drive itself may be faulty.
    Ciao.
    Here is a good place to start looking for a replacement drive:
    http://eshop.macsales.com/shop/hard-drives/2.5-Notebook/

  • How big a internal hard drive can I install in a G5 Powermac

    Model Name:          Power Mac G5
      Model Identifier:          PowerMac11,2
      Processor Name:          PowerPC G5 (1.0)
      Processor Speed:          2 GHz
      Number Of CPUs:          2
      L2 Cache (per CPU):          1 MB
      Memory:          4.5 GB
      Bus Speed:          1 GHz
      Boot ROM Version:          5.2.7f1
    How big a internal hard drive can I install in a G5 Powermac

    2.1 TB for certain & some 3 TB drives work if Partitioned to less than 2.1 TB but then it must be GUID instead of APM, most important is if it is SATA I 1.5Gb/sec compatible.

  • I am trying to find out how to copy the image on my existing hard drive to my new hard drive before I install it so it will be like I didn't do anything.

    I am trying to find out how to copy the image on my existing hard drive to my new hard drive before I install it so it will be like I didn't do anything. Thanks for the info. on changing it.

    Format is found in the Erase Tab:
    The Disk Image is found on the Restore Tab:

  • After installing a new hard drive can I install snow leopard directly from snow leopard disc

    After installing a new hard drive can I install snow leopard directly from snow leopard disc. Or do I have to install previous versions first. iMac 7.1 (2007) 2.8ghz

    You can install directly, assuming the disk is newer than your computer and not designed for a different Mac, but doing so won't install iLife.
    (64305)

  • I want to pgrade to an SSD drive in my Mid 2007 MacBook. What SATA hard drive can I install 2 or 3??

    I want to pgrade to an SSD drive in my Mid 2007 MacBook. What SATA hard drive can I install 2 or 3?? That seems to be just about all I can find out there, so far. Are those drives compatable with this macine?  thx

    SATA II

  • How can I wipe my hard drive and clean install Mountain Lion?

    Hi I have a 21.5 inch mid 2011 iMac running Mountain Lion, I want to wipe my hard drive and clean install Mountain Lion. I dont want all my stuff back, just photos and music, the rest I'll reinstall my self. I also dont have a exteranl harddrive. only two USB's one 2 GB and the other 8 GB. How do I do this? And I dont want to pay for mountain lion again. Thanks!

    I made my partition and am currently reinstalling mountain lion to put on my flash drive. I'm using Lion disk maker 2 thats compatible with mountain lion. I'm doing it right, correct?

  • Just had to put a new hard drive in my Macbook. How do I "backload" my Ipod tunes into Itunes on the new hard drive I had installed?

    I just had to put a new hard drive in my Macbook. How do I "backload" my Ipod tunes back into Itunes on the new hard drive I had installed?

    Somebody told me that as soon as I connect the Ipod to the computer, Itunes will will wipe it clean and install what is in the Itunes library (which is nothing) and that I would need some sort of software to accomplish this. Does it matter that the tunes on the Ipod were all uploaded from cd's and not purchased?

  • How much does Premiere Pro and After Effects rely on the hard drive it's installed on?

    This may be a really dumb question, but how much does Premiere Pro and After Effects rely on the hard drive it's installed on if all your video files, assets, disk cache, etc are on different drives than the one the program itself is installed on?
    The reason I am asking is that I currently have a "relatively" slow Sata II SSD for my C drive that has just my OS (windows 7 64bit) and programs (adobe editing programs, no games) installed on it and nothing else. All of the files used in my projects are saved on either a very fast Sata III SSD or a slower HDD depending on what the files are. For example, disk cache on the Sata III, stills on the HDD.
    Being cyber monday I have the opportunity to buy another very fast Sata III SSD to replace my current Sata II SSD C Drive (just OS and programs). Both synthetic and real world benchmarks show a near double in performance. I just want to know if anyone thinks the upgrade is even worth it because for all I know there won't be any increase in performance since no videos, still, cach, etc will be stored on the C Drive.
    The alternative is to get a second monitor because I currently only use one 21" monitor.
    I suppose another alternative would be to not buy anything on the cyber monday deals and just save money for something else.
    Any advice or input would be greatly appreciated. Thanks!

    Thanks Alex! I think you are right about not being able to notice the difference between the SSDs. I ended up finding a deal to get about $80 off a great monitor that I've been looking at for a while and decided to pull the trigger on it. I thought about it and realized that there have already been a bunch of times where I want to watch a tutorial on youtube and follow allong in AE or PrePro, but have to keep switching windows. I also frequently want to have my video preview on a separate monitor so I can have a taller timeline window. This monitor will help a lot with that. Thanks again for your help!

Maybe you are looking for