Prompt never appears in a 2602i access point

Hello:
Today I converted an AIR-CAP2602I-A-K9 access point to autonomous using the mode button/tftp method, but no matter what IOS I install (I tried 2 different IOS and also tried entering to Rommon - I am able to change IOS because the procedure I used does not need any command), i never get to see the prompt so that I can introduce commands to configure the AP. It's like it hangs after "succesfully" initializing
The only thing I can see all the time are "normal" console messages, and It shows no error message at all. It happened even before the downgrade.
This is where the AP stops, but it is not really hung because console messages could keep showing up. It just never gets to the promt so I can enter some commands. Would not even acept Enter.
Cisco IOS Software, C2600 Software (AP3G2-K9W7-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:12 by prod_rel_team
Initializing flashfs...
flashfs[3]: 200 files, 7 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 31739904
flashfs[3]: Bytes used: 14286848
flashfs[3]: Bytes available: 17453056
flashfs[3]: flashfs fsck took 9 seconds.
flashfs[3]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Uncompressing radio files...
...done Initializing flashfs.
Radio0 present 8764 8000 0 A8000000 A8010000 0
Rate table has 244 entries (64 SGI/104 BF variants)
Radio1 present 8764 8000 0 88000000 88010000 4
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-SAP2602I-A-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
Processor board ID FGL1716S0Q6
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: BC:16:65:95:A7:C3
Part Number                          : 73-14588-02
PCA Assembly Number                  : 800-37899-01
PCA Revision Number                  : A0
PCB Serial Number                    : FOC17151DSW
Top Assembly Part Number             : 800-38356-01
Top Assembly Serial Number           : FGL1716S0Q6
Top Revision Number                  : A0
Product/Model Number                 : AIR-CAP2602I-A-K9
Press RETURN to get started!
*Mar 1 00:00:11.819: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
*Mar 1 00:00:11.935: FIPS IOS test Image Checksum successful
*Mar 1 00:00:11.935: FIPS IOS test Crypto RNG DEK Key Test successful
*Mar 1 00:00:11.939: FIPS IOS test SHA-1 successful
*Mar 1 00:00:11.939: FIPS IOS test HMAC-SHA1 successful
*Mar 1 00:00:11.939: FIPS IOS test AES CBC 128-bit Encrypt successful
*Mar 1 00:00:11.939: FIPS IOS test AES CBC 128-bit Decrypt successful
*Mar 1 00:00:11.939: FIPS IOS test IOS AES CMAC Encrypt successful
*Mar 1 00:00:11.939: FIPS IOS test IOS CCM Encrypt successful
*Mar 1 00:00:11.939: FIPS IOS test IOS CCM Decrypt successful
*Mar 1 00:00:11.939: FIPS IOS test RSA Signature Generation successful
*Mar 1 00:00:11.939: FIPS IOS test RSA Signature Verification successful
*Mar 1 00:00:11.939: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:18.863: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 0 successful
*Mar 1 00:00:18.863: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 0 successful
*Mar 1 00:00:18.863: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 0 successful
*Mar 1 00:00:18.863: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 0 successful
*Mar 1 00:00:18.863: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:24.991: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 1 successful
*Mar 1 00:00:24.991: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 1 successful
*Mar 1 00:00:24.991: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 1 successful
*Mar 1 00:00:24.991: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 1 successful
*Mar 1 00:00:24.991: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:25.007: initializing dot11 onplus
*Mar 1 00:00:25.259: not a autoconfig enabled device!!!
*Mar 1 00:00:27.039: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:28.039: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:01:13.383: Starting Ethernet promiscuous mode
*Apr 12 07:12:42.000: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Apr 12 07:12:42.000: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Apr 12 07:12:42.003: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Apr 12 07:12:42.011: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2600 Software (AP3G2-K9W7-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:12 by prod_rel_team
*Apr 12 07:12:42.011: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Apr 12 07:12:42.991: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Apr 12 07:12:42.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Apr 12 07:12:42.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Apr 12 07:12:44.651: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed
*Apr 12 07:12:44.651: DPAA Initialization Complete
*Apr 12 07:12:44.651: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Apr 12 07:12:44.971: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up <--- CURSOR STOPS HERE AND WON'T ACCEPT ENTER OR ANY OTHER KEYBOARD ACTION
Any thoughts?
Best regards and thanks in advance

Leo, I'm usign SecureCrt, so I disabled XON/XOFF and DTR/DSR as usual, but was not disabling RTS/CTS, so I did and now it is working. Thank you very much!

Similar Messages

Lion boot hangs at point logon prompt should appear

Lion boot hangs at point logon prompt should appear. Unresponsive to mouse or keyboard. Mac mini 2007. Touching power button briefly puts machine to sleep. Hitting key or wiggling mouse then wakes machine and logon proceeds normally. Has happened every time Lion has booted. Never had problems with SL. Fix needed!
TIA,
--Beman

Same issue here, not always but after entering logon password it will hang with the spinning icon. I have to power off then reboot.
Only since Lion upgrade!

Trying to get home shaing working on apple tv using Cisco Access points and a Cisco WLC 5508 with 7.2.110 code. I can get devices working individually but they never see each other. I can ping the apple tv from my laptop and ipad.

Trying to get home sharing working on a corporate wireless network. Cisco wireless.
WLC5508 controller
Cisco 3502 access points
All apple devices on same WLAN - security WPA2-PSK
ITunes account up to date
All devices laterst software.
Can ping apll tv from laptop
can ping apple tv from ipad
Can ping ipad from laptop
can ping laptop from ipad.
Apple tv never sees any other device.
Any ideas?

Fascinating just reading about your setup. I have a WRT350N and have noticed that it will drop its speed, sometimes down to 1Mbps. It seems to do so at about the same time every day, but usually comes back to speed in about 5 minutes. In my experience, the Apple TV will disconnect if the speed falls this low. Try monitoring the Linksys with Netstumbler, Vistumbler, or just in the Windows Network utility.
Check the "lease obtained" and "lease expired" times for your router to see if that is when the network fails. I've just finished reading an angry thread over at the Linksys forum about the WRT330N where someone mentioned that the router wasn't renewing its lease.
"I cannot set it run off automatic DHCP from the WRT330N, the router will not assign it an IP every time the lease expires, causing me to have to manually set an IP on the Print server. That's annoying. Having the router drop IP's to individual machines after 12-48 hours...very annoying."
http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&thread .id=67412
If that is the problem, then I would consider setting up a Static IP address for your Apple TV. You can do that through the user interface -> Settings -> Network -> Configure ... (Quite intuitive as you only have change IP address and the subsequent details remain the same.)
My router assigns IP Addresses in the ranges of 192.168.1.100 ->149. The idea here is to choose an address outside of that range but is not greater than 192.168.1.253 (and should not end in the number 1). You shouldn't have to change the linksys router as long as 50 clients are assigned in that range. You'll have to figure that out by accessing your router webpage at browser address 192.168.1.1 -> the default password is "admin" (without the quotes).
Good luck.

Netctl connects to access points I've never seen before

On my laptop using netcl and auto switching profiles as described in https://wiki.archlinux.org/index.php/Netctl.
Recently, and more than once, I'm connected at a public cafe and I'm suddenly no longer able to reach the internet.
When I investigate, I find that I'm no longer connected to the cafe's wifi, but I am connected to some other essid that I've never seen before. This is disconcerting for possible security reasons but also annoying to get disconnected in the middle of whatever I'm doing.
The essids that my box connects to I've never seen before. (I'm assuming the come from nearby computers.) There is no corresponding profile in /etc/netctl.
To work around the problem, I run
sudo systemctl stop [email protected]; sudo wifi-menu
then reconnect to the access point I was originally connected to.
I really don't want netctl-auto to change a connection that is working. How can I prevent this from ever happening?

That file has a long list of every wireless router I've connected to! I didn't know that was there. It duplicates a lot of information thats in /etc/netctl/... It has passwords, too. I'm not going to post it here.
But I don't see the mysterious routers in that file. The ones I find myself connected to, that I never connected to myself.
... Looking over that file again, I see a strange entry:
network={
key_mgmt=NONE
ssid=""
id_str="wlp3s0-none"
I'm going to delete that. I believe it comes from a time I connected to an essid without a name. But I'm not sure if that's the culprit.
Last edited by Dave Cohen (2014-02-14 17:03:32)

Image Recovery for Cisco Aironet 1300 Outdoor Access Point

We purchased two 1300 APs for outside. There is a new release for the image that we wanted to use so, we have the latest security updates. We downloaded, logged onto the access point just fine, but the image never took. After four hours with a direct connection, it was still going and this morning we came in and it just keep rebooting. Our network guy states it looks like a corrupt image. We can barely do anything and since there is no "mode" button like the earlier models, I have not found anything on web sites or forums to help us reload a good image to the access point. I would appreciate any insight someone has and/or where to look for this. I logged on and downloaded about every manual on the 1300 I could find, but have not found a good way to fix this. Not even the upgrade tool will connect since it just keeps rebooting.

Hi Bruce,
Because (as you correctly noted) the 1300 does not have a mode button you could try this method;
Complete the steps in this section in order to reset Cisco IOS Software-based bridges:
If the privileged command prompt ap# is available in the CLI, the write erase command and the reload command erase the startup configuration and reset the unit.
If the GUI is available, choose System Software > System Configuration. Press the Reset to Defaults button.
Aironet 1300 Series Bridges do not have a MODE button to reset the AP to factory defaults. So, if neither the GUI or CLI is available with sufficient privileges, complete these steps to delete the current configuration and return the entire bridge settings to the factory defaults using the CLI.
Open the CLI with a Telnet session or a connection to the bridge console port.
Reboot the bridge by removing and reapplying power.
Allow the bridge to boot until the command prompt appears and the bridge begins to inflate the image.
Press ESC when you see lines that are similar to these on the CLI:
Loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_ja.20040314"
...#############################################################################Note: In order to access the boot loader, you must press ESC twice. But this action depends on the terminal-emulation software that you use.
Messages that are similar to these appear:
Error loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_
ja.20040314"
Interrupt within 5 seconds to abort boot process.
Boot process terminated.
The system is unable to boot automatically. The BOOT environment variable needs to
be set to a bootable image.
C1310 Boot Loader (C1310-BOOT-M), Version 12.2 [BLD-v122_15-ja_throttle.20040314 100]
bridge:At the bridge: prompt, issue the dir flash: command in order to view a directory of the Flash file system.
The directory is similar to this directory:
bridge: dir flash:
Directory of flash:/
2 -rwx 0 env_vars
5 drwx 384 C1310-k9w7-mx.v133_15_JA.20040314
3 -rwx 1128 config.txt
4 -rwx 5 private-config
3693568 bytes available (4047872 bytes used)
bridge:Delete or rename the files config.txt and env_vars, and reboot the bridge.
Note: Do not forget the / character before the filenames.
bridge: delete flash:config.txt
Are you sure you want to delete flash:/config.txt (y/n)?y
File "flash:/config.txt" deleted
bridge: delete flash:/env_vars
Are you sure you want to delete "flash:/env_vars" (y/n)?y
File "flash:/env_vars" deletedIssue the boot command in order to reboot the bridge at the bridge: prompt, or simply power cycle the bridge.
After the bridge reboots, reconfigure the bridge with the web browser interface, the Telnet interface, or Cisco IOS Software commands.
Note: The bridge is configured with the factory default values that include:
The IP address, which is set to receive an IP address with DHCP. If you do not have a DHCP server, you can access the bridge using the default IP address of 10.0.0.1 using HTTP/HTTPS or Telnet. Once you gain access to the bridge via Telnet or GUI, you can modify the IP address of the bridge.
Note: This default IP address of 10.0.0.1 becomes available only for a short period. So, make sure that you assign your own IP address to the bridge within that period of time.
The default username and password, "Cisco".
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_password_recovery09186a00800949d0.shtml#ca_1310_ser
One other thing, be careful with the new IOS that you aren't loading a LWAPP Recovery Image. (it almost sounds like what may have happened)
Hope this helps!
Rob

AirPort Extreme (5th Gen) WiFi access point disappears but wired ethernet is ok

My AirPort Extreme SSID and access point "disappear" randomly from available WiFi networks. I had a 1st gen AirPort Extreme and never had this problem until earlier this year. I thought it might be a failing radio in the 1st gen unit so I used it as a good excuse to get a 5th gen AirPort extreme about 3 months ago. Same problem has been occuring; unfortunately it is random and I cannot get a handle on what/when/why it is happening.
For example, my iPhone 4S was connected to the network at about 1700 today and when I next checked the phone around 2115, no wifi connection and my network was not listed in the WiFi connections. The base station is away from other wireless devices (mouse, keyboard) and is about 10 feet from the nearest PC and monitor. Both printers are accessed via ethernet, not wifi. The strange and puzzling thing is that the PC, which is connected by ethernet to the AirPort Extreme, is still connected to the internet (I can browse, check email, newsgroups, etc.).
When I run the AirPort Utility, the base station is identified (AirPort Extreme 802.11n 5th Generation), there is an appropriate IP address, Version 7.6 firmware, and MAC address is listed. However, when I attempt to Continue or do a Manual Setup, I'm prompted for the admin password, the progress bar moves during 'reading from the Apple wireless device. Please wait...,' and then the utility reports "An error occured while tryong to access the Apple wireless device. Make sure your network connection is valid and try again. Error -6722.
If I unplug, wait, and reattach the power to the base station, WiFi becomes available again. When the WiFi connection "disappears", the LED light is solid green.
Any insights are appreciated; please let me know other helpful information I can provide.
Scott

I have the exact same problem and it's driving me nuts.
I bought an airport extreme n last week and plugged it in, hooked it up to my adsl router by Ethernet, configured it to set up a new wifi network and got the green light. I use an iPhone 4, iPad 2, and Windows 7 PC with an N wifi adaptor.
The airport works fine for about 2 hours before the wireless network disappears without a trace. Green light remains on the base station and I can connect fine by Ethernet.
"it just don't make sense"
I hope it's not a windows-7-only thing, Apple.
PS. Updated firmware to the newest version, no difference.
Airport is near to a wireless phone so I set a specific wireless channel and frequency to prevent a clash. No change.

Access point confusion

Hey thanks! So is each access point connected to a cable, but just from behind the device if it's not daisy chained? I guess this is the most confusing to me. Sorry to be a pain! ha

All of the jobs that I have had mainly were end user support, hardware/software support. Some server management in AD , Exchange, etc. Virus removal, training, along with network support. Everything though, was pre-existing so I had never set up an entire network from nothing, on my own. Where I work they are installing around 15-20 access points since the building is huge. I am not sure, if any how involved i will be but would like to get some knowledge from people with experience because I want to learn and ensure that I understand what is going on.How are these connected, exactly? When you look at them, they appear to be just on the ceiling or wall with no cords at all (Maybe the Ethernet is hidden?) but lit up. I believe they are POE so they will only require an Ethernet cord, right? How are they connected? To where? Is each one...
This topic first appeared in the Spiceworks Community

WLAN access point "missing" when connection alread...

Hello,
I have an E63 with version 400.21.013 firmware. However, I have experienced this problem from day one. I do not have a data plan but I use WLAN at various locations, and there is a list of access points in the Settings.
I have a home access point configured with WPA2 and I have all the settings saved in the Connection Manager (or is it WLAN Wizard - I don't know). When the phone is not connected to any AP and I use a program that wants data, it will almost always show the "Home" AP in the list which appears right after "Searching for available access points" is briefly displayed. "Home" shows up right below Search for WLAN. There is no problem making the first connection.
However, if the "Home" AP is already in use and I open another program that wants data, at times it will not show my Home AP in the list. If "Searching for available access points" is only displayed for a split second, "Home" will not be in the list. Sometimes I can close the program and open it again and if "Searching for available access points" stays on screen for about a second, then "Home" will be on the list and I can connect. Sometimes I will have to try 3, 4, 5 times, and sometimes it will never "see" the AP unless I disconnect the WLAN and start all over.
Right at this moment, there is no problem. I can open program after program and connect via my "Home" AP. But it is frustrating when it does happen. Has anyone seen this or found a remedy?
Thanks.

Have you tried changing the WLAN channel (i.e. frequency) of your home WLAN access point / router?
Try switching between few different channels (like 1, 3, 6, 9, 11) to see if some channel happens to work more reliably. It is possible that there is some radio interference (neighbouring WLAN networks, cordless phones, Bluetooth devices etc.) on the currently used WLAN channel, causing phone to discover this network less reliably.
In case your WLAN access point / router includes 802.11n support, make sure that your AP's "channel width" is set to a standard 20MHz mode (instead 20/40MHz).
This is a bit long shot suggestion (just guessing), but if switching the WLAN channel related setting on the AP doesn't help then you could also try editing your phone's access point (the one created for you home WLAN network, under Tools -> Settings -> Connection -> Access Points) so that your phone should consider this particular WLAN network as an "Hidden SSID" (even if network really isn't hidden) by changing the "Network status" setting from Public to Hidden.

N86 8MP, Nokia Email 2.1.0, Access point troubles

I know that his has been an never ending saga. I just don't seem to be able to give it up.
There is a well known issue about Nokia Email 2.1.0 not being able to define group access points.
When I try to do that I am offered only particular access points or "None". This is ever so annoying as I have to manually change the access point every time I leave my home WiFi.
I am aware that there are ways around this using connection manager apps (I tried several: Auto WeFi, Easy WiFi.... ) but I was not happy with the results. One of them even disabled me from editing my access points.
It is weird that it is possible to define "Internet" as a access point for Exchange but not for normal e-mail providers.
Some people suggested to setup acces point to "Default" while setting up a new email account. However, I've never seen this option.
I think Nokia's terminology is so vague. What would be "Default" connection as opposed to "Internet"?
In addition, in "Network Destionations" it is possible to define the "Internet" group as "Default" so this will be the same thing, or...??? Am I missing something?
I stumbled upon this article that Nokia would release a patch addressing this access point issue.
I spent hours searching for the patch to no avail. Does anybody know whether that patch exists at all?
http://www.e71fanatics.com/2009/01/big-ooops-in-recent-nokia-email-version.html
Having exhausted all possibilities I was thinking I could install Nokia Messaging 9.7. Apparently this version is compatible with S60v3 unlike the Nokia Messaging 10.2.
I have no idea whether Nokia Messaging 9.7 was ever ment to be for N86 8MP but if not does anybody know whether the unsigned version could be installed instead?
I would appreciate any piece of advice or suggestion.
Alex

Hello!
I can't update my e-mail client via Nokia e52 internet browser.
I enter address email.nokia.com, click download link. The application Nokia Email 9.07 has downloaded. After this the suggesting message to install Nokia Email 9.07 appears. But error appears after my agreement - "An incompatible version of this product is detected, and has to be uninstalled first"
I have no possibility to uninstall detected Email, so I don't see any Email client in Application Manager.
Nokia developers, please, fix this bug as soon as possible

Canon 70D, Wifi access point with Android

I bought a Canon 70D this week and I cannot get the Wifi access point option to work with my Nexus 7 2013 or my Samsung Galaxy S3. I was able to connect my 70D to my Wifi network and see the device that way. But when on the road you won't always have access to a local LAN. When I try the access point mode both devices never see the 70D.
I rebooted both Android devices after installing the EOS app. I also get the camera in access point mode first and then launch the EOS app. I let the app sit for several minutes and never finds the 70D.
Any tips?

Hi gquiring!
Thanks for posting.
When you go through the setup process on the camera, are you selecting [Easy Connection] ot [Manual Connection]? If using [Manual Connection], try using the [Easy Connection] instead.
When prompted by the camera to connect to it with your smartphone, do you see the SSID of the camera show up in the list of networks you can connect to on your smartphone?
If this is a time sensitive-matter, additional support options are available at Contact Us.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Access point are not coming up after upgrade image of WLC

Hi,
I have AIR-WLC4402-50-K9 WLC i that current IOS is 7.0.98.218 and i upgraded with 7.0.116.0 IOS but after upgrading and reboot the WLC from 15 access point 3 access point are not coming up and 12 are coing up and working fine (4 1142 and 11 1131 series access point) 3 which are not coimg is 1131 series access point. when i login with console to 3 access point its rebooting 2 times and coming on ap: prompt.
In between that i reloaded the WLC one more time because from 15 acess point only 4 aceess point are came up and i also cleck the show boot on wlc its output is
7.0.116.0 (default)
7.0.98.218 (active)
so i reload the wlc and checked out of 15 acess point now 12 acess point are up and still 3 are not. And i also checked the output of show boot command its
7.0.116.0 (default)(active)
7.0.98.218
So i things its because of when 2nd time i reload the wlc the remaining 3 access point are getting image from wlc but because of reload its connection should be loss and error loading flash error are coming on acess point.
After that i recover the IOS for access point and convert into autonomus and from autonomus convert into Leightweight Access point. I also attached the procedure for recover the ios of access poing
But my question is why this 3 access point are not coming up is this happen's after upgrading wlc can any one please send me Step by Step WLC S/W Upgrade' process and if this this happens some time please send me any doccument related to this.

Sunil,
When you rebooted the controller did you do it from the Web GUI, the CLI, or did you physically reboot the controller? I believe and maybe incorrect but if your getting the ap: < prompt > that means that there is no firmware on the unit. If you have restored these to functioning autonomous unit and then re-converted them to Lightweight and it's still happening then we need to look at a debug output of what is happening when those AP's attempt to join the controller.
The capture you attached shows that it appears to join the controller and get a config, but are you saying that when it reboots again it stops working?? the other thing I would reccomend is clear out the flash memory since your capture shows the possibility that there are several copies stored there.
Hope this helps.

2 Access Points Same Wireless Network

ok the basics: I have a cable modem hooked up to a linksys router ... the signal does not cover the whole house, so I got a linksys range expander ... set the whole thing up and everything works nice ... except that my PB keeps picking up the weak signal from the main router and doesnt connect to the range expander ... they both have the same security settings and all and they even appear as the same wireless network ... any thoughts on how to make my PB connect to the access point with the best signal?

I don't think that was the question posed. The issue is not how do I increase a particular access point's range, or can I dispense with one of them.
The issue is how to best work with TWO access points on the SAME network. I am very interested in this issue, as I have not been able to get my system to work properly. In short, there is an Airport Express (access point only) in the upstairs family room, and a Motorola (router and access point) in the basement. For those of us who own the new PB's, it is a lost cause to get reception comparable to the iBooks. Literally hundreds of posts exist in this area trying to improve it. So the ability to automatically connect to the highest reception point is a great benefit.
I have a unique IP address to each access point, and the Airport Express is tied to the Motorola router through ethernet. I have tried both devices on the same wireless channel, and each on its own (1 and 11). I have also tried using the same SSID & password for each point, and giving them unique names. In all situations, the result is the same. Once the Mac is connected to a particular access point, it will never switch over to the other one, unless connectivity is completely lost to the first one (i.e. unplug the AE).
This does not meet the 'roaming' idea. The goal is that when I am upstairs, I automaticallly connect to the AE, as it is strongest. When I move downstairs, it should connect to the Motorola, as the signal strength is SIGNIFICANTLY increased (we are running a PB, here). But this never happens. Instead, the PB will choke on internet browsing, because it is connecting to the gateway through a very weak wireless signal upstairs, when an alternate strong one is right next to it !!
Doesn't matter if I sleep in between relocating. All settings are automatic; that is, the Airport will automatically connect to the available networks. What I have to do is click the airport signal meter and choose my access point in order to change.
For those who think this is all acceptable performance, I don't have to do this with my HP work laptop. Windows does not seem to have a problem with proper, correct, and optimized roaming.
Hi-res PB15, 1.5GB Mac OS X (10.4.7)

E90 - Access point in use

Hi
I changed "access point in use" for incoming mail from default
"Always ask" to another one. I don't know, how to change it back.
In selection are only existing access points. Any idea? Regards

I have a N95 8GB so some things might differ on your phone. Anyway, I have noticed that the mail access point connection is maintained even after downloading all messages. You can check the status of the connection by viewing the menu of your mailbox in 'messaging' and looking for a 'connect/disconnect' tab. If you try to view a link in a message while still connected to the mail access point, the phone will automatically use that existing connection. (There appears to be no 'disconnect after mail retrieval' function which is unsatisfactory IMO.) As far as I can see, your only option would be to manually disconnect from the mailbox connection at which point the 'always ask' prompt would reappear for the web link. I think I understand what you would like to have, but this is not possible I fear because the phone will always opt for the pre-existing connection.

Requirement for Native VLAN on Flexconnect Access Point

Hi All,
Just looking at AP configuration using 5508 WLC.
We have APs deployed at all branch sites connected over a corporate L3 WAN to a Data Centre which houses the WLC(s)
When setting the AP for Flexconnect mode there is a requirement that one native VLAN must be configured for each FlexConnect AP. If the AP is attached to a L2 switch and I want to enable multiple VLAN Mappings then I would need to add these VLANs to the allowed VLAN list on a trunk link between the AP and the switch (802.1Q) on the branch site.
Normally if I configured a trunk link I would never add the Native VLAN to the trunk and never use it for any traffic. In this case it would appear that I MUST use the native VLAN (which seems to go against my better judgement). So my question (after all this) is: What must the AP use the Native VLAN?
Thanks All.

This has always been a standard practice for access points that has to connect to a trunk port. This goes back to the autonomous access points and also with FlexConnect and Mesh if your setting up Ethernet bridging. Wired side is different from the wireless side as you have noticed.
Please rate helpful post and Cisco Support Community will donate to Kiva
Scotty

How do I setup an Access Point/Repeater on FIOS

I have a MI424WR-GEN2 router/modem from Verizon. Since Verizon installed it in the basement, my wi-fi at various other points is not the strongest. I do have cat-5 in various parts of the house. So, I'd like to add one of my old routers to the network and have it act as an access point or repeater (not sure if there is a difference between the two designations). I'm technical enough to be dangerous and do damage but I wasn't having any luck doing this ... for one, I can't even figure out how to access it to program it since 192.168.1.1 is the verizon router.
I have three choices for a device:
(1) Linksys WRT54GS
(2) Linksys BEFW11S4
(3) Netgear RangeMAx DGND3300 (my preferred choice because it has B/G/N as options)
Help please!
Thank you!

Ok, it is working, more or less. But there seems to be a connectivity or reliability issue. For some reason, and it seems to only be on my laptop (but perhaps because the others in my house aren't on engough and haven't noticed an issue?).
I periodically lose connectivity but the network is not down. I turn off my laptop wi-fi, wait a few seconds, and turn it back on.
I suspect this is something to do with competing protocols ... I don't know, and Verizon didn't confirm, if their router support b/g AND n. The netgear supports b/g/n. Also, the Netgear is dual band. Right now, the netgear, as an access point, has both 2.4Ghz (11g) and 5Ghz (11n) SSIDs set to the same name. Should they be different? In which case, do we need an additional wi-fi to recognize? It doesn't appear as if I can disable one of them.
For the time being, the netgear access point is right next to the laptop. COuld the proximity cause a problem? I've never had that issue before but trying to identify anything!
Any thoughts?
Thanks!

Prompt never appears in a 2602i access point

Similar Messages

Maybe you are looking for