Ps3 nat problem

why cant u get a open nat with ps3 always on moderate how do u get it to open ?

This link should help.
NAT Problems on games consoles and computers
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

Similar Messages

Azureus Nat problem

Hey
I am running a 17 inch imac and experiencing some trouble with my bittorrent client Azureus.
I simply never get the green smiley face. I read the wipi-help from Azureus and confirmed by using their instructions that I do have a NAT problem. I have no firewall running. I did continue reading the explanation in the Wiki but it seems to be PC oriented. Can anybody give me some good info to fix this problem?
By the way will my downloads be faster when I do use a correctly configured NAT?
Samuel
PS I am not using a router just a ADSL Modem

I had the same problem but turned off my firewall, opened the port 59981, turned my firewall back on & it worked straightaway, my d/l speed shot up frpom 20kb to 280kb. My only problem now is that when I am running azereus my internet connection sometimes drops and the only way round it seems to be turning off my mac & cable modem and rebooting. I'm on Telewest Blueyonder cable with a webstar cable modem and it only happens when I'm using Azereus.
Very frustrating!!

Open NAT problems with Xbox One .

When I first got my 1900ac I used Media Priortization to get an open NAT for Call of Duty Advanced Warfare on my Xbox One ; prioritizing the Xbox . It worked fine for about 6 months until I changed cable/net provider to Nextech in Ks. This company uses the 1900ac to hook up it's system for all it's customers ( since I already had one they're using mine ). Unfortunately I'm unable to get an open NAT in this game anymore ; I've tried just about everything , NAT forwarding , triggering , Media Prioritization . Nextech support & Xbox Live support , useless . Tried Portforward . com , nothing . Forwarding port 53 cuts off net connection & doing the static ip change for Xbox didn't help . Almost everything I've looked at seems out of date & I'm at my wits end . It would seem by now Linksys should have solutions available , any ideas ?

Thank you chin_pamz13 for your response . I tried to check if my modem had a public or private ip address but I'm not sure how to do that ; I've read about double NAT's elsewhere . Regardless , I think I've finally found a solution that seems to be working so far . I went to the website " tech - recipes . com " & found an article , " Xbox One open NAT " by Aaron St. Clair . I tried his first suggestion about port triggering , with extra ports I had'nt seen before . That did not work for me so I followed his instructions for putting the Xbox in the DMZ & it's working ! I think my problems from before were the result of improperly setting up the static ip address for my router & Xbox . Previous instructions had me changing the ip in the console along with the router ; Aaron said not to do so in the Xbox , let the router do the work it's supposed to do & make sure the settings in the console are on automatic . In the router at the DMZ , I was'nt sure how to proceed , but at the bottom is a section labeled DHCP reservations list ; clicked on that , saw XboxOne , clicked on that & it filled out the MAC address above for me . Then I went to the Xbox network settings , advanced settings & clicked " automatic " at ip address , subnet & DNS . I checked mutiplayer connections & did the " hold bumper & trigger buttons " trick & finally got an open NAT ; fired up CoD Advanced Warfare & got the open NAT there also . I may have screwed up when I did the port triggering but since the DMZ fix seems to work I'm going to leave things alone . Hope this helps others with open NAT problems .

Xbox360 WRT54GS ver. 6 NAT problems

my xbox 360's NAT is set to strict and prevens me from connecting with a lot of otehr players and my wireless router is a WRT54GS ver. 6

for xbox 360 having NAT problem... you need to call Xbox to ask for the port numbers to open...now if your isp is dsl then call them up and set the modem to bridge to set the rtr to pppoe...in this way we will be able eliminate the multiple NAT issues and for your xbox to work...
CamZ

Route or NAT problem?

Hi Everyone,
We have an ASA 5540 at our data center, with ASA 5505's at most remote sites.
At the sites without layer 3 switches behind the ASA 5505's, we can't reach the data center internal network through the ASA for flow-export, etc.
So, what I'm basically saying is, even though the tunnel is up and everything behind the branch ASA can reach the data center networks fine, the ASA itself cannot reach hosts on the data center network.
I'm hoping to configure these ASA 5505's so I can do flow export and SNMP logging from them, but without this routing or nat problem resolved, they just won't do it.
Doing a packet tracer from the ASA 5505 to the data center server I'm most focused on, reveals this:
BRANCH5505f01# packet input inside icmp 10.15.16.1 8 0 10.1.1.15 detailed
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcb0b6698, priority=1, domain=permit, deny=false
        hits=1004755, user_data=0x0, cs_id=0x0, l3_type=0x8
        src mac=0000.0000.0000, mask=0000.0000.0000
        dst mac=0000.0000.0000, mask=0100.0000.0000
        input_ifc=inside, output_ifc=any
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   10.1.1.15       255.255.255.255 outside
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   0.0.0.0         0.0.0.0         outside
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (rpf-violated) Reverse-path verify failed
I am thinking the problem is NAT related, but with the new ASA NAT rule format due to v9.1... struggling to get a grip on where it is... any thoughts/help are appreciated.
Ken
Here is the relevant config for the Branch ASA and also the relevant config from the data center ASA:
Branch ASA Config Parts:
: Saved
ASA Version 9.1(2)
hostname BRANCHASA5505
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
speed 100
duplex full
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
description LAN_NETWORK
nameif inside
security-level 100
ip address 10.15.6.1 255.255.254.0
interface Vlan2
nameif outside
security-level 0
ip address <outside ip> 255.255.255.248
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object-group network BRANCH_NETWORKS
description BRANCH LOCAL NETWORKS
network-object 10.15.6.0 255.255.254.0
object-group network LAN_NETWORKS
network-object 10.0.0.0 255.0.0.0
network-object 134.200.131.0 255.255.255.0
network-object 134.200.220.0 255.255.255.0
network-object 134.201.2.0 255.255.255.0
network-object 163.243.195.0 255.255.255.0
network-object 172.16.0.0 255.240.0.0
network-object 192.168.0.0 255.255.0.0
network-object 10.1.3.0 255.255.255.0
network-object 10.31.2.0 255.255.255.0
network-object 10.1.1.0 255.255.255.0
network-object 172.26.1.0 255.255.255.0
object-group network NETWORK_MGMT
network-object 10.0.0.0 255.0.0.0
access-list DATACENTER_VPN_ACL remark *******************************************************************
access-list DATACENTER_VPN_ACL remark * FOR VPN CONNECTION TO DATACENTER/VEYANCE NETWORKS *
access-list DATACENTER_VPN_ACL remark *******************************************************************
access-list DATACENTER_VPN_ACL extended permit ip host <outside ip> host <outside ip datacenter asa>
access-list DATACENTER_VPN_ACL extended permit ip object-group BRANCH_NETWORKS object-group LAN_NETWORKS
access-list INSIDE_NONAT extended permit ip object-group BRANCH_NETWORKS object-group LAN_NETWORKS
access-list INSIDE_FILTER extended permit tcp any4 any4 eq www
access-list INSIDE_FILTER extended permit tcp any4 any4 eq 8080
logging host inside 10.1.1.15
flow-export destination inside 10.1.1.15 2055
ip verify reverse-path interface inside
ip verify reverse-path interface outside
nat (inside,outside) source static LAN_NETWORKS LAN_NETWORKS destination static BRANCH_NETWORKS BRANCH_NETWORKS route-lookup
nat (inside,outside) source static BRANCH_NETWORKS BRANCH_NETWORKS destination static NETWORK_MGMT NETWORK_MGMT route-lookup
nat (inside,outside) source dynamic any interface
object network obj_any
nat (inside,outside) dynamic interface
access-group FROM_OUTSIDE in interface outside
route outside 0.0.0.0 0.0.0.0 <outside ip gateway> 1
route outside 10.1.1.15 255.255.255.255 <outside ip datacenter asa> 1
management-access inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
tunnel-group <outside ip datacenter asa> type ipsec-l2l
tunnel-group <outside ip datacenter asa> ipsec-attributes
ikev1 pre-shared-key *****
class-map type regex match-any DomainBlockList
match regex DomainList-Netflix
class-map type inspect http match-all BlockDomainsClass
match request header host regex class DomainBlockList
class-map inspection_default
match default-inspection-traffic
class-map httptraffic
match access-list INSIDE_FILTER
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map type inspect http http_inspection_policy
parameters
protocol-violation action log
class BlockDomainsClass
reset log
policy-map URL-filter-policy
class httptraffic
inspect http http_inspection_policy
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect http
class class-default
flow-export event-type all destination 10.1.1.15
service-policy URL-filter-policy interface inside
prompt hostname context
Datacenter ASA Config Parts:
ASA Version 9.0(1)
hostname DATACENTERASA5540
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
names
interface GigabitEthernet0/0
description *** TO OUTSIDE NETWORK AT DATACENTER ***
speed 100
duplex full
nameif OUTSIDE
security-level 0
ip address <outside ip>
interface GigabitEthernet0/1
description *** TO INSIDE NETWORK ***
nameif INSIDE
security-level 100
ip address 10.1.3.2 255.255.255.0
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network LAN_NETWORKS
network-object 10.0.0.0 255.0.0.0
network-object 134.200.131.0 255.255.255.0
network-object 134.200.220.0 255.255.255.0
network-object 134.201.2.0 255.255.255.0
network-object 163.243.195.0 255.255.255.0
network-object 172.16.0.0 255.240.0.0
network-object 192.168.0.0 255.255.0.0
network-object 10.1.3.0 255.255.255.0
network-object 10.31.2.0 255.255.255.0
network-object 10.1.1.0 255.255.255.0
network-object 172.26.1.0 255.255.255.0
object-group network DATACENTER_NETWORKS
network-object 10.1.0.0 255.255.0.0
object-group network BRANCH_NETWORKS
network-object 10.15.6.0 255.255.254.0
access-list BRANCH_VPN_ACL remark ****************************************************
access-list BRANCH_VPN_ACL remark * FOR SITE TO SITE VPN TO BRANCH WV USA *
access-list BRANCH_VPN_ACL remark ****************************************************
access-list BRANCH_VPN_ACL extended permit ip host <outside ip> host <outside ip branch asa>
access-list BRANCH_VPN_ACL extended permit ip object-group LAN_NETWORKS object-group BRANCH_NETWORKS
flow-export destination INSIDE 10.1.1.15 2055
flow-export template timeout-rate 1
flow-export delay flow-create 180
ip verify reverse-path interface OUTSIDE
ip verify reverse-path interface INSIDE
no failover
nat (INSIDE,OUTSIDE) source static LAN_NETWORKS LAN_NETWORKS destination static BRANCH_NETWORKS BRANCH_NETWORKS route-lookup
access-group FROM_OUTSIDE in interface OUTSIDE
route OUTSIDE 0.0.0.0 0.0.0.0 <outside ip> 1
route INSIDE 10.0.0.0 255.0.0.0 10.1.3.1 1
route OUTSIDE 10.15.6.0 255.255.254.0 <outside ip branch asa> 1
crypto map OUTSIDE-MAP 156 match address BRANCH_VPN_ACL
crypto map OUTSIDE-MAP 156 set pfs
crypto map OUTSIDE-MAP 156 set peer <outside ip branch asa>
crypto map OUTSIDE-MAP 156 set ikev1 transform-set ESP-3DES-MD5 ESP-3DES-SHA
tunnel-group <outside ip branch asa> type ipsec-l2l
tunnel-group <outside ip branch asa> ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
class class-default
flow-export event-type all destination 10.1.1.15
user-statistics accounting
service-policy global_policy global
smtp-server 172.19.1.137
prompt hostname context
call-home reporting anonymous
Again, any help you can provide is appreciated... will vote for best...

I ran it, with the source IP corrected (it is 10.15.6.2):
BRANCHASA# packet input inside icmp 10.15.6.2 8 0 10.1.1.15 detailed
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcb0b6698, priority=1, domain=permit, deny=false
        hits=1203279, user_data=0x0, cs_id=0x0, l3_type=0x8
        src mac=0000.0000.0000, mask=0000.0000.0000
        dst mac=0000.0000.0000, mask=0100.0000.0000
        input_ifc=inside, output_ifc=any
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   0.0.0.0         0.0.0.0         outside
Phase: 3
Type: UN-NAT
Subtype: static
Result: ALLOW
Config:
nat (inside,outside) source static BRANCH_NETWORKS BRANCH_NETWORKS destination static NETWORK_MGMT NETWORK_MGMT route-lookup
Additional Information:
NAT divert to egress interface outside
Untranslate 10.1.1.15/0 to 10.1.1.15/0
Phase: 4
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   10.15.6.0       255.255.254.0   inside
Phase: 5
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (inside,outside) source static BRANCH_NETWORKS BRANCH_NETWORKS destination static NETWORK_MGMT NETWORK_MGMT route-lookup
Additional Information:
Static translate 10.15.6.2/0 to 10.15.6.2/0
Forward Flow based lookup yields rule:
in id=0xcb12f2f0, priority=6, domain=nat, deny=false
        hits=15824, user_data=0xcb0fdef8, cs_id=0x0, flags=0x0, protocol=0
        src ip/id=10.15.6.0, mask=255.255.254.0, port=0, tag=0
        dst ip/id=10.0.0.0, mask=255.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=inside, output_ifc=outside
Phase: 6
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcaa712e0, priority=0, domain=nat-per-session, deny=true
        hits=77610, user_data=0x0, cs_id=0x0, reverse, use_real_addr, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=any, output_ifc=any
Phase: 7
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcb0bc128, priority=0, domain=inspect-ip-options, deny=true
        hits=91404, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
        src ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=inside, output_ifc=any
Phase: 8
Type: INSPECT
Subtype: np-inspect
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0xcb0bbc28, priority=66, domain=inspect-icmp-error, deny=false
        hits=4585, user_data=0xcb0bb238, cs_id=0x0, use_real_addr, flags=0x0, protocol=1
        src ip/id=0.0.0.0, mask=0.0.0.0, icmp-type=0, tag=0
        dst ip/id=0.0.0.0, mask=0.0.0.0, icmp-code=0, tag=0, dscp=0x0
        input_ifc=inside, output_ifc=any
Phase: 9
Type: VPN
Subtype: encrypt
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
out id=0xcb0c1218, priority=70, domain=encrypt, deny=false
        hits=708, user_data=0xbf63c, cs_id=0xcb9ad918, reverse, flags=0x0, protocol=0
        src ip/id=10.15.6.0, mask=255.255.254.0, port=0, tag=0
        dst ip/id=10.0.0.0, mask=255.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=any, output_ifc=outside
Phase: 10
Type: NAT
Subtype: rpf-check
Result: ALLOW
Config:
nat (inside,outside) source static BRANCH_NETWORKS BRANCH_NETWORKS destination static NETWORK_MGMT NETWORK_MGMT route-lookup
Additional Information:
Forward Flow based lookup yields rule:
out id=0xcb12fb00, priority=6, domain=nat-reverse, deny=false
        hits=15837, user_data=0xcb124438, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
        src ip/id=10.15.6.0, mask=255.255.254.0, port=0, tag=0
        dst ip/id=10.0.0.0, mask=255.0.0.0, port=0, tag=0, dscp=0x0
        input_ifc=inside, output_ifc=outside
Phase: 11
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 143081, packet dispatched to next module
Module information for forward flow ...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_translate
snp_fp_adjacency
snp_fp_encrypt
snp_fp_fragment
snp_ifc_stat
Module information for reverse flow ...
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: allow

ASA5512 iOS 9.3 inside nat problem

Hi,
I face some nat problem. i have ASA5512 iOS 9.3 its connect outside (ip: 37.10.1.2/29) for internet and inside (ip 10.78.61.1/24) for LAN and server.
I configure dynamic nat for internet its work. In LAN switch has 4 VLAN one server VLAN ip add 10.88.61.0/24.
Now i map a public ip 37.10.1.3 for server 10.88.61.10 from outside internet its work. But when i try to ping server public ip 37.10.1.3 from LAN its not ping but server local ip 10.88.61.10 ping from LAN.
How can solve the issue i need to ping public ip from LAN. ALL LAN VLAN are nat on ASA outside interface (ip: 37.10.1.2/29).
interface GigabitEthernet0/0
description #### Connect TO Internet ####
nameif outside
security-level 0
ip address 37.10.1.2 255.255.255.248
interface GigabitEthernet0/1
description #### Connect TO Core Switch ####
nameif inside
security-level 100
ip address 10.78.61.1 255.255.255.0
access-list outside-in extended permit ip any any
access-group outside-in in interface outside
access-group outside-in in interface inside
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network obj_Ser
host 10.88.61.10
object network obj_Ser_WAN
host 37.10.1.3
nat (inside,outside) source static obj_Ser obj_Ser_WAN
object network obj_any
nat (inside,outside) dynamic 37.10.1.4
same-security-traffic permit intra-interface
Thanks
Afzal

Hi,
Try this NAT:-
nat (inside,inside) source static obj_Ser obj_Ser_WAN
Thanks and Regards,
Vibhor Amrodia

Airport Express PS3 Nat type 3 problem

Recently I bought a Playstation 3. I have succesfully created a connection using the airport express connected to my speedtouch modem. The problem is that when I do an internet connection test on my PS3, it says that UPnP is unavailable and NAT type is 3. This is a major problem because I can't join chats or games, how can I get NAT type 2? It would be greatly appreciated, Thanks in advance...
Message was edited by: EDuranMac

I've done that already, foward the ports I mean. Right now I have my PS3 under DMZ and I'm still getting NAT type 3. Since it wouldn't hurt to try this again (forwarding the ports) I will, meanwhile I have a question: do I need to disable UPnP on both the router and the PS3 or leave enabled? Also, does it hurt to enter the PS3's ip address in the DCHP reservation or do I need to leave it outside?
Message Edited by Alakratt on 06-22-2008 08:26 PM

Linksys E2000 (2 Xbox 360's and 1 PS3) Open Nat Problem

Hi everyone,
I recently bought the Linksys E2000 for my house so i could enjoy wireless internet. The problem is i have two Xbox 360s which one is wired and the other wireless. It seems that i can't have both Xboxs with OPEN NAT and whichever one connects to the router first is the one to have OPEN NAT no matter what. This leaves the other Xbox with MODERATE or STRICT. Is there a way to have both open at the same time? If anybody knows help would be appreciated! Thanks
**I have a PS3 also connected wirelessly, but that one is always OPEN. Didn't know if that would affect my PS3's NAT if i were to change the setting on my router.

Here's a checklist. Got it here.

WRT54G with PS3 NAT TYPE 3 needs to be changed!

Hi all,
I've been trying to change my Nat type from a 3 to a 2. I have a ps3 20gig (sadly) that is directly connected to my laptop (wired). My laptop has wifi and I'm able
to play games online. The only problem is that I'm not able to invite friends into my party or host any games for Call of Duty 4. My ps3 is set at Nat Type 3
and I think that's the problem here. I have a Linksys WRT54G router and UPnP is enabled on it. My laptop has UPnP enabled as well. I've tried everything I could
find, but there's not much info for someone who has a setup like me.
I setup a static ip for the ps3 on my laptop, and the only ip that will work is 192.168.0.10.
Here is my ipconfig:
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:\Documents and Settings\MADE>ipconfig/all
Windows IP Configuration
        Host Name . . . . . . . . . . . . : MADE
        Primary Dns Suffix . . . . . . . :
        Node Type . . . . . . . . . . . . : Hybrid
        IP Routing Enabled. . . . . . . . : Yes
        WINS Proxy Enabled. . . . . . . . : No
        DNS Suffix Search List. . . . . . : no-domain-set.bellcanada
Ethernet adapter PS3:
        Connection-specific DNS Suffix . :
        Description . . . . . . . . . . . : Realtek RTL8168/8111 PCI-E Gigabit E
thernet NIC
        Physical Address. . . . . . . . . : 00-17-31-25-3B-27
        Dhcp Enabled. . . . . . . . . . . : No
        IP Address. . . . . . . . . . . . : 192.168.0.10
        Subnet Mask . . . . . . . . . . . : 255.255.255.0
        Default Gateway . . . . . . . . . :
Ethernet adapter Wireless Network Connection:
        Connection-specific DNS Suffix . : no-domain-set.bellcanada
        Description . . . . . . . . . . . : Intel(R) PRO/Wireless 3945ABG Networ
k Connection
        Physical Address. . . . . . . . . : 00-13-02-1D-36-FC
        Dhcp Enabled. . . . . . . . . . . : Yes
        Autoconfiguration Enabled . . . . : Yes
        IP Address. . . . . . . . . . . . : 192.168.1.101
        Subnet Mask . . . . . . . . . . . : 255.255.255.0
        Default Gateway . . . . . . . . . : 192.168.1.1
        DHCP Server . . . . . . . . . . . : 192.168.1.1
        DNS Servers . . . . . . . . . . . : 192.168.2.1
        Lease Obtained. . . . . . . . . . : Wednesday, November 21, 2007 12:39:2
9 AM
        Lease Expires . . . . . . . . . . : Thursday, November 22, 2007 12:39:29
AM
Any kind of help would be apprieciated.

IP Address. . . . . . . . . . . . : 192.168.1.101
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
DHCP Server . . . . . . . . . . . : 192.168.1.1
DNS Servers . . . . . . . . . . . : 192.168.2.1
Your WRT54G is connected to another router (maybe your modem?) which has IP address 192.168.2.1. To get that working you have to configure port forwarding on 192.168.2.1 and on the WRT54G at 192.168.1.1. UPnP won't help you here because UPnP will only configure the WRT but not the router to which the WRT is connected to. Thus you have to set explicit port forwardings (don't know which ones the PS3 requires).
Otherwise consider setting up the WRT as access point only like this.
Or find out how to set the modem into bridge mode (i.e. turn off the router in the modem). After that you have to configure the router for your internet connection (usually PPPoE for DSL or DHCP for cable). This way you have the WRT54G directly connected to the internet.
Message Edited by gv on 11-21-2007 05:41 PM
Message Edited by gv on 11-21-2007 05:41 PM

Playstation 3 nat problems fix BT hub

The problem is with online gaming on the ps3 where the nat is set to "moderate" rather than "open".
First access you hub settings by typing in 192.168.1.254 then settings/advanced settings/application sharing now with your ps3 turned on select playstation 3 from the game/application menu select it and also select its address from the device menu...apply.
Now the next bit is up to you as I'm no internet security expert but it seems to keep the nat in "open" state.... from application sharing under advanced settings select firewall and disable it then apply.
Now go back to the most overrated game in history...black ops and your nat should be open - this seems to work for most.

Your connection is Openreach Modem -> BT Home Hub 5 -> iMAC.
After a bit of reading - http://www.broadbandchoices.co.uk/guides/hardware/bt-home-hub
Openreach Modem - Optical Network Terminal (ONT).
HH5 - is a 4-port Ethernet Router/Switch
It looks like BT may be locking the MAC addresses of the modem and hh5 with access control lists, so customers cannot connect a device to replace the HH5.
You have an option. Connect one of the HH5 LAN ports to the WAN port of the Airport.
Set the Airport to Bridge mode, no DHCP address distribution, Create a Wireless Network.
You can just ignore the HH5 SSID(s) completely and just connect to the ones you create on the Extreme. The iMac can connect to any LAN port on the Extreme or one of the remaining HH5 LAN ports.
The only challenge you may have is, if the number of IP addresses the HH5 can allocate is limited to 4 (by BT's configuration). It can be verified using more than four (4) devices.
If this works, then there are alternatives where a new LAN within a LAN can be created if the IP address limitation becomes an issue.

Airport Express and PS3 Nat Type 3

I have a Airport Express with a Cisco DPH151-AT modem for AT&T DSL. I'm having a lot of problems trying to get my PS3 get a Type 1/2 Nat, but all I get is Type 3. It's causing a lot of lag and unable to join groups or connect in certain games. Can anyone help me?!?!

I'm confused about this microcell device. What exactly does that mean
A microcell is basically a small version of a cellular tower. It is intended to provide cellular service in a location where the current service is too weak. It provides, in this case, a cellular 3G network to be used by cell phones. It does NOT provide a Wi-Fi network for your computers or PS3. For that you would need either a Wireless Access Point (WAP) or a Wireless Router.
Now the Airport is directly wired to the Cisco DPH151-AT. So is this just a basic modem/router setup? The Cisco DPH151-AT being the modem and the Airport being a router?
The Cisco needs to be connected to either an Internet modem or router in order to access the Internet. I'm not 100% sure, but I don't think that this is a dual-use device that functions as both a DSL modem & 3G microcell.
Is the Cisco connected to another device? If so, what is its make & model?

WRT120N WITH SPEEDSTREEM 4300 PS3 NAT 3 ISSUES

I HAVE A WRT120N ROUTER WITH A SPEEDSTREEM 4300 MODEM. I HAVE TRIED PUTTING MY PS3 IN THE DMZ VIA THE MAC ADDRESS, (PLAYSTAION NETWORK SAYS THAT SHOULD WORK). IT DIDNT. I TRIED ALL THE PORTS LISTED FOR THE PS3 THAT DIDNT WOKRK, I HAVE ENABLED UPNP I HAVE DISABLED IT, I HAVE TRIED EVERYTHING. PLEASE IF ANYONE HAS HAD THIS SAME PROBLEM WITH THIS SETUP PLEASE POST THE SOLLUTION. THX

rkerr08 wrote:
Ethernet adapter Local Area Connection:
   Connection-specific DNS Suffix . : domain.invalid
   Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet
   Physical Address. . . . . . . . . : 00-1B-24-C3-37-E5
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   Link-local IPv6 Address . . . . . : fe80::e0ba:c38a:b17:1ee%11(Preferred)
   IPv4 Address. . . . . . . . . . . : 192.168.254.2(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Friday, February 11, 2011 1:09:17 PM
   Lease Expires . . . . . . . . . . : Monday, March 20, 2147 7:38:15 PM
   Default Gateway . . . . . . . . . : 192.168.254.254
   DHCP Server . . . . . . . . . . . : 192.168.254.254
   DHCPv6 IAID . . . . . . . . . . . : 234887972
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-13-93-51-64-00-1B-24-C3-37-E5
   DNS Servers . . . . . . . . . . . : 192.168.254.254
                                       192.168.254.254
   NetBIOS over Tcpip. . . . . . . . : Enabled
As you can see the SpeedStream is a NAT router. The IP address of the Speedstream is 192.168.254.254.
You have three options:
1. Configure forwardings on the SpeedStream and the WRT. I would not recommend this.
2. Use the SpeedStream as router and the WRT as simple access point and not as router.
3. Set up the SpeedStream as modem, i.e. put it into bridge mode, and then configure your WRT for your internet connection and use only the WRT as router.

VPN / NAT Problem

Hi I have quite a complex (to explain) VPN problem, I've built a model in GNS3 but I still cant get it to work. here is the topology
1. SiteW is the main site, if W-CLient wants to talk to S-Client (on SiteS) the traffic is simply NATTED to 106.200.194.240 and sent there (this works fine).
2. SiteB is a new site, Ive set that up with a Site to Site VPN, that works fine.
New Requirement
If a user at SiteB wants to Talk to a Client at SiteS, then the traffic should go over the existing VPN to W-FW1 then get decrypted and routed there. This is the bit I CANNOT despite HOURS of tweaking and testing get to work.
What I've done
On W-FW2
Added Site S to the existing interesting traffic ACL and added a 'NO NAT' for it like so;
object network S-CLIENTS
subnet 65.253.1.0 255.255.255.0
access-list VPN-INTERESTING-TRAFIC extended permit ip object B-CLIENTS object S-CLIENTS
nat (inside,outside) source static B-CLIENTS B-CLIENTS destination static S-CLIENTS S-CLIENTS
On W-FW1
Added Site S to the existing interesting traffic ACL and added a 'NO NAT' for it like so;
object network S-CLIENTS
subnet 65.253.1.0 255.255.255.0
access-list VPN-INTERESTING-TRAFIC extended permit ip object S-CLIENTS object B-CLIENTS
nat (inside,outside) source static S-CLIENTS S-CLIENTS destination static B-CLIENTS B-CLIENTS
At this point packet tracer said the traffic was being blocked by ACL so I added
access-list inbound extended permit ip object B-CLIENTS object S-CLIENTS
access-list inbound extended permit icmp object B-CLIENTS object S-CLIENTS
access-group inbound in interface outside
Now Packet Tracer was happy, Still B-Client Cannot Ping S-Client!
W-FW1 can ping S-Client
Attempting to ping S-Client from B-Client brings up the tunnel (phase 1 and 2) but no traffic ever travels BACK to B-Client.
Running Wireshark on the 106.200.194.1 interface of S-FW1 whilst attempting to ping 65.253.1.10 from S-FW1 shows traffic (as expected) but if I ping from B-Client it gets nothing (so I'm assuming the traffic never gets out of W-FW1
Help!

First check if the packet from the S client is making it back to the W-F1.
Configure Captures on the interface that is connected to the 106.200.194 subnet.
#cap capin interface <interface name> match ip host <sclient ip> host <bclient ip>
#show cap capin
Capture is bidirectional. Hence no need to enable it in the opposite direction.
If the packet is seen coming back from the Sclient and still not getting encrypted then do asp drop capture to see if the ASA is dropping it
#capture asp type asp-drop all
send the traffic.
#show cap asp | in <Sclient IP>
If the packet is see in this capture then the ASA is dropping it.
Then do a packet tracer to see why it is dropping it.
#packet-t input <Sclient connected interface name> icmp <sclient IP> 8 0 <b client IP> det.
Check why the packet is dropping.
if the capin capture does not see the reply packet then check the reply path and routing.

Cisco ASA5505 multiple public ip nat problem

Hello,
I've been having weird problem with static nat.
First have to say that i've been searching answer for this and not yet found...
I have three public IP:s from /24 network like 83.x.x.10, 83.x.x.25 and 83.x.x.41 all using netmask 255.255.255.0.
I'm using 83.x.x.10 on ASA outside interface and trying to do static nat for inside servers with those other IP:s, but not yet solved it.
Using Cisco ASA 5505 software v9.02
Config:
object network obj_guest
nat (guest,outside) dynamic interface
object network obj_any
nat (inside,outside) dynamic interface
object network w2008
host 192.168.1.10
object network w2008
nat (inside,outside) static 83.x.x.27
object service RDP
service tcp destination eq 3389
access-list outside_access_in extended permit object RDP any object w2008
access-group outside_access_in in interface outside
This works other networks that are like whole network with /29 mask and have router in front of ASA using bridge. But in my case i just have DSL modem bridged in front of ASA. This static nat works like should if i use like Zywall USG series fw and this same configuration works in my customers, but they have those scenarios i said having mask /29 and router in front...
It seems that the problem is in ASA, like i won't show those public IP:s to public router from my operator. Because if i roll those other public IP:s on my ASA:s outside interface: i will use 83.x.x.25 and 83.x.x.41 on outside interface and after that put back my original 83.x.x.10 then my static nat is working just fine, atleast few hours, but not in next morning because ISP router flushes ARP cache.
What trick i need to do with ASA to get this working?

Here is the command reference for that:
http://www.cisco.com/en/US/docs/security/asa/asa91/command/reference/a3.html#wp1824414
Apology, didn't know that you are running that version that supports this new command.
The reason why you need that is because the next hop device is not in the same subnet as your ASA as you have DSL modem bridge in front of the ASA, hence you would need that command enabled.

Does anybody have a solution for the NAT problem?

Is somebody's application or Applet able to play any RTP stream behind a NAT Router? Can anybody establish any kind of connection / broadcasting between two subnets? I've got my RTP-Transmitter@public IP (using RTPManager...SendStream.start()), and I try to receive the stream from my local network which is behind a router (DHCP: 192.168....).
I read forums, newsgroups, looked for any solution for days all over the web but I've found nothing. Zero.
What's the secret? Any hints?
Best regards from Munich / Germany,
r.v.

Hi
I have the same problem.
I have one appletTransmitter that capture video from webcam and transmit it to other client on internet.
I try to transmit medialocator from appletTransmitter to servlet1 and then save MedialLocator as servlet attribute, then other client can connect to servlet2 that send saved MediaLocator to appletClient.
APPLETTRANSMITTER:
URL url=null;
MediaLocator media=new MediaLocator("vfw://0");
try{
url = new URL("http://localhost:8080/servlet1");
catch(MalformedURLException mue){mue.printStackTrace();}
URLConnection conn=null;
try{
conn = url.openConnection();
catch(IOException ioe){ioe.printStackTrace();}
conn.setDoOutput(true);
OutputStream os=null;
ObjectOutputStream oos=null;
InputStream in=null;
ObjectInputStream iin=null;
MediaLocator mResp=null;
String r=null;
try{
os=conn.getOutputStream();
oos=new ObjectOutputStream(os);
oos.writeObject(media);
//oos.writeObject("Prova Servlet");
oos.flush();
catch(IOException io){io.printStackTrace();}
catch(ClassNotFoundException cn){cn.printStackTrace();}
SERVLET1
ObjectInputStream objin = new ObjectInputStream(request.getInputStream());
MediaLocator ml =null;
try{
ml = (MediaLocator) objin.readObject();
context.setAttribute("media",ml);
catch(ClassNotFoundException e)
{e.printStackTrace()}
But on servlet1 there is a ClassNotFoundException: MediaLocator
What do we think about the solution and exception problem?
Best Regards,
Nico from Italy

Ps3 nat problem

Similar Messages

Maybe you are looking for