PS3 Nat Type 3 - Airport Extreme Router

Greetings internet people;
I am an Airport Extreme user (connected to a Motorola 2210-02 DSL modem via ethernet) - with a PS3 who is finding it incredibly frustrating to get my network to work with my PS3 in NAT 1/2 -(Modern Warfare 2 is difficult with variable lag/no party invites).
This is my current network layout:
http://grab.by/ABS
Modem information screen:
http://grab.by/ACb
Our ISP is Bellsouth (AT&T) and the modem is currently set to PPoE. I think I set up port forwarding to a static IP for the PS3, but still, nothing I've done/read online has worked, or I haven't done it right.
(I tried plugging the PS3 directly to the modem and it still remains in NAT Type 3.)
I need the network to stay in tact - so that wireless works etc. I could set up the switch between the modem, but I'm still not sure if that'd do it. ----
Any help would be greatly appreciated, I want to figure this out so I can actually play my PS3 online :<
Peter

I have the same Motorola model 2210, but the screen shots in the original post were different, so you may have to search a bit for things.
The 2210 provides NAT service, and the only way to hook it up to the AEBS to Connect Using "Ethernet" will result in the double NAT because the AEBS is also furnishing NAT services.
You will need to use the web interface for your modem and you will probably need to plug it into your computer to configure it. The setup page(s) on my model will display when you enter 192.168.1.254 into your browser. Check your documentation to see if you will use the name address or a different address.
When you log into the modem, look for an Advanced setting, PPP Location, or similar. You need to change the PPP setting from the current "On the Modem" to "On the computer or router". If there is a setting for "Bridge Mode", you can use this as well. Update to save changes on your modem and it will restart.
Important...you may not be able to get back into the modem configuration again unless you reset the modem by holding in the reset button for approx 10 seconds. Then you will be able to reconfigure the modem if you need to do so.
Reconnect the modem to the AEBS and open AirPort Utility - Manual Setup. If AirPort Utility does not "see" the AEBS, temporarily connect an ethernet cable from your computer to one of the LAN <-> ports on the AEBS and try again.
After you click Manual Setup, click the Internet icon at the top of the setup pane and look for the Connect Using setting. You need to change this to PPPoE. Then enter your user name (probably your email address with the ISP) and password. Important....leave the Service Name area completely blank. Do not enter anything here.
Click Update and the AEBS should restart with a green light in about 20 seconds. You have now eliminated the double NAT between the modem and AEBS. Sorry, I can't help with details on the game console, so there may be some additional configuration needed for that device.
Please post back on your progress.

Similar Messages

How do I find my Airport Extreme router online?

When I type in the address from my Airport Extreme router (version 802.11n), I cannot find it online. It does not show as an IP address. I am having some problems with my printer and want to set up a static IP address, but want to make sure that I use the correct one. Is there a way to make sure there is only one IP address being used?

You must use the Airport Utility application on your PC to configure the Airports. They are not configured with a web based program.
AirPort Utility 5.6.1 for Windows - Support - Apple

Trying to get my air video app and my airport extreme router to work.

Hi there. I am getting really frustrated and desperate. I just purchased the app "air video" on my iPad. Installed the software on my mac. Works awesome when I'm on MY WIRELESS NETWORK. I didn't think it would be an issue once I left the house and tried to go on someone else's network to connect, but it just won't work. It keeps giving me the error "host not reachable". I tried opening up the air video troubleshooting info and tried everything but nothing seems to work. I tried under the "remote" tab in the air video server preferences. I clicked both "enable access from Internet" and the "auto map port" options. In the box below I just see the word status and the spinning wheel along with "looking for UPnP or NAT-PMP compatible devices" but the wheel has been spinning for about 15 mins. It doesnt appear to be finding anything.
I've also clicked off the "auto map port" to see if that would do anything. I got the pin and tried that. Still nothing. I tried to look for some information on port forwarding for my airport extreme but everything I'm googleing seems to be years out of date.
I am currently on Mac snow leopard 10.6.3 I believe. Everything is latest version. Using comcast modem with apple airport extreme router. Latest version of Air video app and software. On iOS 4.3.1.
Anyone that can try to help me out, I would be eternally grateful.
Thank you so much
Keith

* need to edit to" trying to get my iPhone not iPhoto**"

Using an Airport Extreme router with PC.

I was told that I could use the Apple Airport Extreme router with my PC - but I can't seem to figure it out. Any suggestions to get started?

Sorry to be so ignorant when it comes to this type of stuff. I have a laptop (Dell) and a home computer (PC). The Apple man told me all I had to do with my previous router was unplug it and plug in the Extreme and it would walk me through the steps. It didn't. I think I may have changed some settings on the PC. Now I can't even get the previous router to work so I'm hardwired in on my laptop to even get here.
Do I need to hardwire in the PC, download the above utility, then try to hook up the Extreme router? How do I make it "secure" or locked so no one else can use it other than ones with the key code?
Thanks so much for the above information. Going to try it now.

Airport Extreme Route - Logging into remote computer using VPN

is there anything i need to change on my airport extreme router. I used to be able to access remote computer via vpn and now I cant ever since i started using the airport extreme. Im trying to access remote computer using windows xp home.

bkohlmeier wrote:
On one of the 2wire config screens last night, it showed my various devices and next to each one said "IP" of 108.54.... so it was showing the public IP of each one, versus say "192.168.1.160".
Ok, that is weird. Is each IP different and how many devices do you have getting public IP's.. there should only be one available and the only device getting it should be the extreme.
If you only need a bridged modem. go out and buy a cheap single port modem. (I presume this is DSL service. Sorry I am not in US, so what is obvious to you may need spelling out).
We often use the cheapest TP-Link modem here.. TD-8817 which are like $25 for bridged modem.. works really well.
I think also you will find as far as pc is concerned the 2wire is actually the better router. Apple decided to use NAT-PMP on their routers instead of near universal upnp used by all windows networking and just about everything else. That makes opening ports that much harder on the Extreme for games etc.
With the new version utility you can turn on guest network even with the Extreme in bridge.. and what you miss in terms of dhcp is not that great.
If you want to get it working, let me suggest bridging the extreme for the moment. I am sure you will find no issues with Remote Desktop direct through the 2wire, as you probably used it in the past that way.

How do I connect a PC via ethernet to my new Airport Extreme router?

I just replaced an old Actiontec router with a new Apple Airport Extreme router to work with my Verizon FIOS service. Connection to all Apple products via ethernet or wireless works OK, however I cannot get the PC up and running via its ethernet connection to the Airport Extreme. Any help would be much appreciated.

If your other devices are working then it is probably the PC's IP configuration.
First, make sure that the PC is actually connected to the Extreme by verifying the lights are on at the Ethernet ports on the PC and the Extreme.
If you are using DHCP to manage the IP addresses then make sure that the PC is configured to "Obtain IP Address Automatically" for both IP versions 4 and 6.
When I replaced my Linksys w/ an Extreme I forgot that I had a couple devices configured with static (manual) IPs. My old one used the "192.168.1.nn" and my Extreme defaulted to "10.0.1.nn". Once i converted all the static IPs to the correct subnet then all was good.

Officejet Pro 8000 Wireless won't connect to my new Airport Extreme router

I have owned my Officejet 8000 Wireless printer for about a year and had no problems with it. However, my old wireless router wasn't fully Mac compatible so I couldn't secure it with a password. I now need a secure network, so I bought an Apple Airport Extreme router in December.
I installed the router last night and it is working fine on my iMac, my PC laptop and my iPhone.
However, tonight I am trying to set up the Officejet Pro 8000 with no luck. I've searched the posts here for 3 hours and am not finding the help I need. Based on the other posts I've read, I am describing my situation below.
I am trying to set up the printer from my Intel iMac with Mac OS 10.6.4
I am trying to set up the printer with the HP Setup assistant that I just installed from the printer software.
On the first wizard screen it tells me that my device is not configured (I agree)
Then I ask it to configure for a wireless network.
When I get to the Network Selection page, both my network AND my guest network (which I let my neighbor use) are shown on the list with full signal strength.
When I click my network and then continue, the HP setup wizard freezes, and I have to force-quit it.
When I click my guest network and then continue, I get the message that my network is not within the reach. (FYI, the printer is 10 feet from the router.)
I have tried powering on/off the printer, router, and computer at all different stages of the process with no luck.
For my Airport:
My radio mode is set to the most compatible choice
MAC access control is not enabled
Everything is WPA2 security
"Use wide channels" and "Create a closed network" are UN-checked
The channel is set to 11
I am happy to try the "Add network client" thing I saw on other posts, but I don't think I have a printer front panel where I can start the "WPS" (don't know what that is) process. If I do, it's not obvious and not in the HP manual.
My ISP is Comcast (cable internet).
I would really, really appreciate some help! Please let me know what information I forgot to include and I will be happy to provide it.
Thank you!
This question was solved.
View Solution.

First, you should be at 10.6.6, so please do Software Update (Apple menu) over and over until there are no more updates.
From where did you get the HP software for your printer? Was it labeled as being compatible with 10.6?
Finally, you will need to reset the printer so, let's do that:
Press and hold the Power button, press Network button, (on some models, press the Wireless button ), two times, press the
press the Cancel button three times, and release the Power button.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Can't make Airport Extreme router work with non-Apple device

I am trying to help a friend who has a PC (Windows 7) that has a wired Ethernet connection to his girlfriend's Airport Extreme router. He wants his Internet-capable Blu-Ray player and her IPad to wirelessly access the Internet via the Aiport Extreme router, with both the Blu-Ray player and the IPad's Internet access protected by WPA-2 encryption (both devices are capable of WPA-2). How do I do this?
Here are the problems we've run into:
1) The Airport Utility for Windows (5.6.1) has been installed on the P.C., and we've used it to update the firmware on the Airport Extreme router. However, after we followed the Aiport Utility instructions to set up the network, all the router wanted to do was look for an Apple device. His girlfriend and her IPad are out-of-town right now, so the only device within range was the Blu-Ray player, and the router did not see it. Not only that, but almost all the menu options on the Airport Utility were "greyed out" (unusable), except for "Configuration." I am very troubled by the fact that the Airport Extreme router seems to want to look only for Apple devices.
2) In order to get Internet access for his Blu-Ray player for the time being, my friend pushed the "reset" button on the Airport Extreme router, and he can now use his Blu-Ray player for Netflix and other Internet streaming options. However, the Blu-Ray's wireless Internet access is an unencrypted connection, and the Airport Extreme router is displaying a flashing amber light -- not a good situation.
3) Although I know his girlfriend could access the router via her IPad when she returns, she is French-Canadian, and her IPad operates in French. I happen to know some French, but I have enough trouble trying to understand wireless networking terminology in English without having to try to figure out the equivalent terms in French. Thankfully, the Airport Utility for Windows on his P.C. is in English, so that's what we've got to use to solve this problem.
I have profound respect for Apple products, but I'm a Windows/Linkysis router guy, so that's why I'm stumped. Can anybody out there help me?

Which model of the AirPort Extreme Base Station (AEBS) do they have? What is the version of firmware that you updated it to?
By default, the AEBS will broadcast an unsecured Wi-Fi network with a network name (or SSID) of something like Apple Network NNNNNN. This would be similar to a Linksys when first powered-up.

I just purchased an airport extreme router to increase the range of my wifi. I have an imac with 10.5.8. I get a flashing yellow light on the base unit and it tells me I need airport utility to install yhe ubnit. Where do I get this and how do I do it?

I just purchased an airport extreme router to increase the range of my wifi. I have an imac with 10.5.8. I get a flashing yellow light on the base unit and it tells me I need airport utility to install yhe ubnit. Where do I get this and how do I do it?

sylviafromhanover wrote:
So I assume that the original modem stays installed with the coaxial cable and the Exrtreme is in addition to that.
Yes, that is correct.
Did you have the instructions that came with your Airport Extreme? Are you sure you have it setup properly? Here is the setup guide:
http://manuals.info.apple.com/en/airportextreme_802.11n_userguide.pdf
Ensure you have everything setup properly. Once you do this and if you are still having trouble, follow Star's instructions.

I have a Sony Bravia KDL46W905 TV but I can't get it to connect the Airport Extreme router

My Sony Bravia KDL46W905 TV won't connect to my Airport Extreme router and the internet. It recognises and picks up my home wireless network though and I'm inputting the correct password but still won't connect. The router is set to WPA2 Personal.
Anyone any ideas?

While most devices should connect using WPA2 Personal, please temporarily test using no security to see if the Sony TV will connect that way.
If it will, then try the more compatible setting of WPA/WPA2 Personal on the AirPort Extreme and test that way.
However, if the TV will not connect using no wireless security.....then it is a no brainer to conclude that the TV will never connect with security enabled....so more troublehooting is going to be required.
In that case, make sure that the name of your wireless network......
Does not exceed 20 characters, fewer would be better
Does not contain any special characters like an apostrophe, asterisk, dollar sign, etc
Does not have any blank spaces
For example, if the current name of your wireless network is something like.....
rpepler's wireless network
Change that to read something like.....
rpeplerwireless
Same rules for the wireless network password

If you have an Airport Extreme router and a slow Internet connection ...

I know that Internet connection speeds are extremely variable, but I wanted to share this post for anyone having performance problems (very slow Internet connection speeds) while using an Airport Extreme router. This may or may not help you, but it might help someone.
I have a RoadRunner Turbo account, and I was experiencing consistently slow Internet download speeds (an average of only about 300KB/sec). However, when I bypassed my router and connected my Mac directly to the Time Warner modem my download speeds were 6 to 8 times faster (up to about 2MB/sec).
After weeks of tinkering and reading Apple documents I discovered that my Airport Extreme router had an improper setting. That setting is found under: Manual Setup -> Internet -> Internet Connection -> Ethernet WAN Port. When I was experiencing the very slow speeds, my Ethernet WAN Port setting was: '100 Mbps/Full Duplex.' To fix the problem I simply changed this to 'Automatic (Default).'
This one change resulted in a huge, positive performance boost for me. I hope this post helps other people.

You use an App like Filebrowser. Details here:
http://www.stratospherix.com/products/filebrowser/

Seeking a driver for my printer to run through my Airport Extreme router

Im trying to find a driver for my Lexmark X1100 series printer which would allow me to run the printer through the usb port of my Airport Extreme router. The printer works when plugged directly into the usb port of the computer. I have a Windows 7 Asus computer. Can anyone help me please. I am using the Bonjour printer wizard to set up the router for the printer. Thanks

There is no driver that will allow that, as this printer only works by connecting it to a host computer, not to a network. No printer driver or software is ever installed to the AirPort Extreme for any printer. Printer drivers and print/scan/fax software (if any) must be installed separately to each computer that will be using a printer.

MacBook pro and airport extreme router. How to print wirelessly to an old HP wireless photosmart all in one printer

With MacBook pro and airport extreme router, how can I print wirelessly to an old HP wireless photosmart all in one printer? What is needed or what process?

You need to make sure that the HP has an updated printer driver that works with 10.6 for that printer. You can check here:
http://www8.hp.com/us/en/support-drivers.html

Update firmware on airport extreme router

How can I update firmware on my airport extreme router?

Please checkout the following Apple Support article on the details on how to update your AirPort's firmware.

Ethernet Connection Randomly Dropping w/ AirPort Extreme Router

My wired ethernet connection drops sometimes randomly, but I think it tends to do it more if I'm in an audio chat with someone on iChat (not sure). Here is my setup:
FiOS ISP (always been reliable in the past) -> AirPort Extreme (router) -> Cisco gig-e switch (reliable) -> 2008 Mac Pro running Snow Leopard (no I do not use wifi) (my computer) -> Internet sharing to my brother's computer via ethernet port 2 (set up after the new router was installed, but problem happened without it)
It seemed to start doing this once I switched the router to AirPort Extreme. We were using the one Verizon gave us, a junky Actiontec router that was messing with our DNS and port forwardings but wasn't dropping my computer's connection randomly.
I have it set to use DHCP. When it drops, other things have connection, just not my computer. It drops for about 30 seconds then comes up. I've already tried rebooting the router and the switch. I suspect that something is funny with the DHCP because I rarely get the message that my computer's name has already been taken (by itself!), which has always happened even with the old router. Nothing is stealing my address. Anything else I should try?

Try the basics first:
Change your router channel number. Most times this works & is all you have to do.
Disconnect & reconnect your modem. unplug it for about 10 seconds. Plug it back in. Do the same for Apple’s routers. Wait for everything to reboot.
System Preferences>Network
Click the Assist Me button.
In the next window that pops up, click the Diagnostic button & do the necessary.
Research Knowledge Base for network problems that pertain to the OS that is currently installed on your computer. See these basic networking KB Articles: http://support.apple.com/kb/HT1401 AirPort troubleshooting guide
http://support.apple.com/kb/HT2712 Using network locations in Mac OS X
Manually provided DNS server addresses are higher priority than DHCP's
http://support.apple.com/kb/HT1714 Solutions for connecting to the Internet, setting up a small network, and troubleshooting
============================
What to do when you can't connect to the Internet
Also, run the Airport Utility app which is located inside the Utilities folder.
=====================
If using a Linksys router, contact LinkSys Customer Support and/or post in their forums.
If using Apple's Airport, please re-post over in one of the AirPort Forums.

Should Airport Extreme router be routinely powered down?

I know the design helps it cool...but when done on the system at day's end, is it a good idea to power the airport extreme router down? That would mean pulling out the power cord.

While waiting for operations to take, I had a few moments to ask engineers some basic questions. For one, I teach computer graphic arts, and one of my issues is that other teachers use the computer labs as well and its difficult to train people to shut machines down say for the weekend. I asked the engineer...what about shutting down computers? Critical, or no?
His advice was that computers should be shut down at least once every three days to rest over night. Definitely over the weekend when everyone is gone.
Also...thanks on this bit of back and forth, its been instructive. From what I take from it...shutting the extreme down is half-a-dozen one or the other. Doesn't seem it will effect the unit itself, its longevity...but its warmth suggests to me energy is being used. My thinking is if my wife and I are going to be gone for several days or say a week's time...from the standpoint of energy, wouldn't hurt to shut it down. As for storms...the feeling is it should not all that much matter.

PS3 Nat Type 3 - Airport Extreme Router

Similar Messages

Maybe you are looking for