Psc 1315 printer error message

After printing one document, on the next one the printer slowed considerably. Since then the Check Printer light is blinking and I was getting an error message (no longer getting message, light is blinking and it just won't print).  The cartridge had been fine.  I have done the trouble shooting process including installing a recently purchased brand new cartridge just in case with no luck.  I do have some problems getting my Word program to work properly and wonder if that can be part of the problem.

Hello,  Please try the below steps...
1.Click Start button on the Computer .
2.then click on Control Panel .
3.then Printers and Faxes
4.On top-left, click on Add a Printer
5.Click on Add a Local Printer
6.Then while "Use an Existing port" is selected , select "Virtual USB port ... " then click Next
7.from the Manufacturer list, select HP, and then under Printers list select Deskjet 990c" , then Click next and complete the wizard
Now try printing . It should work.

Similar Messages

  • Printer error messages

    psc 2170 all in one printer, error message "remove and check cartridge" this has appeared for no obvious reason when I now switch on. I have removed and cleaned contact points on both cartridges and printed to no avail so would be most grateful for any suggestions that might help.
    Thank you
    This question was solved.
    View Solution.

    Hi - Did you clean the contacts in the printer (carriage) as well?  If not, try that to see if that resolves the problem - Step 5 in this document.
    If that doesn't resolve the problem, the next step is to replace the cartridges (one at a time, in case only one of them is bad). 
    Hope that helps.
    Say Thanks by clicking the Kudos thumbs up. Please mark the post that solves your problem as an Accepted Solution so other forum users can utilize the solution.
    I am an HP employee.

  • How to print error messages in browser?

    When I visit a jsp file in browser, there's some errors in the jsp file, so the browser returns
    The page cannot be displayed
    There is a problem with the page you are trying to reach and it cannot be displayed.
    I want the detail error messages, so I can debug my problem. How to print error message in browser or find the message in some log file?

    Hi Kanaraja,
    Thanks for your answer. I need to get certain information from the list. So, I use LIST_To_ASCII FM. However, may I know the ascii_tab should be type to what? And after this FM, do I have to use another FM to display the ascii list?
    data ABAPLIST type ABAPLIST OCCURS 0.
    SUBMIT  RPCALCU0 VIA SELECTION-SCREEN
    with PNPXABKR = 'US'
    with PNPTIMRA = 'X'
    with PNPPABRP = '10'
    with PNPPABRJ = '2003'
    with PNPPERNR-LOW = '100750'
    with PNPPERNR-LOW = '109202'
    with PNPPERNR-LOW = '100255'
    with PNPABKRS-LOW = 'US'
    with SCHEMA = 'ZUSP'
    with RADI_EDT ='X'
    with EDT_VARI = 'CUS&SAP_US'
    with TST_ON = 'X'
    EXPORTING LIST TO MEMORY and RETURN.
    CALL FUNCTION 'LIST_FROM_MEMORY'
      TABLES
        listobject       = ABAPLIST
    EXCEPTIONS
       NOT_FOUND        = 1
       OTHERS           = 2.
    CALL FUNCTION 'LIST_TO_ASCI'
      EXPORTING
        list_index         = -1
      TABLES
        listasci           = asci_tab
        listobject         = ABAPLIST
      EXCEPTIONS
        empty_list         = 1
        list_index_invalid = 2
        OTHERS             = 3.
    IF sy-subrc NE '0'.
      WRITE:/ 'LIST_TO_ASCI error !! ', sy-subrc.
    ENDIF.

  • How can I print emails? Printing Error message that no printers are installed. (Printers are installed.)

    When I click File > Print, I get a Printing Error message that no printers are installed. Printers are installed. When I click Yes to install a new printer, I receive a new error message that "Windows can't open Add Printer / The local print spooler service is not running. Please restart the spooler or restart the machine." I updated to the new version of Thunderbird 24.6.0. Using Windows 8. I restarted the machine. I confirmed printers are installed using Control Panel. I do not see any way to restart a print spooler. How can I fix this? Thanks.

    The print spooler is a windows service and is required to print. I would hazard a guess you can not print with any application.
    What I am saying is I think your windows instalation has a problem, not Thunderbird.

  • I am getting a "printing error" message on my Pixma M432 and a lightening icon at the right

    I am getting a "printing error" message on my Pixma M432 and the lightening shaped icon in the triangle beneath the stop button is flashing.  My documents won't print and are backed up onscreen on my computer.  I have turned it off and on. What is wrong?

    solution?

  • Printer error message

    Printer error message
    Printer hp LaserJet CP1525nw
    Windows 7
    The following message is displayed when sending any file to the above printer.
     "hpmns115.dll has stopped working"

    Hi jwnova142 ,
     Welcome to the HP Forums.
    I see that you are having an issue with a Paper Size Error when attempting to print.
    First off, please make sure that you have the printer power cable connected directly to a wall outlet and not a power bar/strip. Here is a document that uses a LaserJet printer as an example but it is meant for HP products in general. Please click on the following link that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
    I have also located a document that deals with the 'Paper Mismatch,' or 'Paper Size Mismatch' Error Message Displays When Printing.
    If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
    Thanks for your time.
    Cheers,  
    Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    W a t e r b o y 71
    I work on behalf of HP

  • I'm getting a "printer error" message when I try to print a document with a lot of scans in it. Any suggestions?

    I'm getting a "printer error" message when I try to print a document with a lot of scans in it. Any suggestions?

    OK, I tried a few things, and I do not understand the results.
    1) I opened the document in Preview, and it would only recognize the three initial pages which I typed using the Pages App. It did not recognize the bulk of the text which I copied from Appleworks 6. It also did not recognize any of the scans.
    2) I tried opening a pdf in Preview, and it would only recognize the scans. (No Text!)
    3) I tried copying everything (select all, and command-c) in Pages, and then opened a blank Pages doc, and typed Command-v. This got me all of the text, but none of the scans!
    4) I was worried that my Pages app might be corrupted, but I successfully converted a similar 78-page document with copied materials from Appleworks 6 and similar scans, ant this worked perfectly.
    My conclusion is that my file must be corrupted. Is there any way to check this? shabda88

  • Envy 5534 on MAC- print error message unable to convert post scrip file

    New printer set up fine prints letter but when I want it to print a page with bar code on get error message :-
    print error message unable to convert post scrip file
    Can any one help please
    This question was solved.
    View Solution.

    Hi @itsalex,
    What type of bar code are you printing, and from what program? Just a thought, what if you print the barcode as an image, if you are not already? Try File>Print> Advanced> Print as Image> print.
    If the issue persists, let's reset the printing system and repair the disk permissions; doing so may resolve the issue.
    Reset Printing System
    Click the Apple icon ( ), and then click System Preferences.
    In the Hardware section, click Print & Fax/Scan. The Print & Fax/Scan dialog box opens.
    Right-click (or Ctrl +click) in the left panel, and then click Reset printing system…
    Click OK to confirm the reset.
    Type the correct Name and Password.
    Click OK to reset the printing system. The Print & Fax dialog box shows no printer selected
    Note: This will remove all printers in the print and Fax/Scan, any printer removed can be re-added later by clicking the plus (+) symbol.
    Repair Disk Permissions
    On the Dock, click Applications, and then click Utilities.
    Double-click Disk Utility.
    Highlight your hard drive/partition on the left (by default this is "Macintosh HD").
    Click the Repair Disk Permissions button at the bottom of the window.
    Once the repair is complete, restart the computer and add the printer back.
    When you add the printer, please ensure you are using the HP driver.
    Select Add other Printer or Scanner 
    Select the printer you are adding and next to 'Use' you can select the printer drive. In the screenshot below, you will see Airprint is auto selected, you can change it to the HP driver though.
    I look forward to hearing back from you.
      Talk to you later alligator 
    Please click the Thumbs up icon below to thank me for responding.
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Sunshyn2005 - I work on behalf of HP

  • Photosmart 6510 Printer error message 0xc19a0003.

    I have a Photosmart 6510 Printer error message 0xc19a0003. I have re-powered the printer but still get the error message Oxc19a0003. Suggestions to fix?
    Thanks!

    You are correct, gksurgeon, the 5510 does not have a removable printhead. If you followed the steps in the document above, then the printer will need to be replaced.
    If you are still in warranty, HP may replace the printer at no cost to you. I'll link the information to get in touch with them below. The link will take you to a form to fill out. Once you fill it out and it is processed, it will give you the printers warranty information, a case number, and the phone number to call.
    HP Technical Support Case Call Form:
    http://goo.gl/w7Hgh
    -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
    I am not an HP employee.

  • Getting print error messages after 8.1.3 update

    Adobe Acrobat 8 - Since the 8.1.3 update a couple days ago, I am now getting print error messages in the Adobe PDF printer status box when I send any document to the Adobe PDF printer. The actual printing of the document in Adobe works correctly, but these error messages occur as well - even though the document printed just fine.
    I am running Windows Vista Ultimate and did not have the issue prior to the 8.1.3 update.

    I have removed PDFMaker from Office, to try to simplify the troubleshooting. All attempts to print end up the same, whether from PDFMaker (before I removed it from Office), from print to Adobe PDF from within an Office app, or using Create a PDF in AP 8.1.3 from an Office file ... the last hourglass comes up in "reading Adobe PDF" and stays up. I can see the "target file" created in WinExpl but greyed out, and the hourglass (busy) never goes away in AP 8.1.3.
    In contrast, if I want to create a pdf from a "save as" text file, AP 8.1.3 creates the pdf instantly. Create a pdf from scanner also works fine. This problem is definitely related to updates, since AP 8.1 worked perfectly the last time I used it from Office, which was perhaps 2 months ago.
    AP 8.1 suddenly stopped working this week with a "can't create PDF" error message, I updated AP all the way to 8.1.3, and have the problem described above. I don't get an error message now, the create PDF or print to PDF simply never completes.
    BTW, both my desktop and notebook run Vista Ultimate 64-bit, both have registered and activated copies of AP 8.1.3, and Office 2007, and both have the exact same problem.
    I uninstalled AP 8.1.3 on the desktop, installed the trial version of AP 9.0, and experienced the exact same problem as with AP 8.1.3, the create pdf never completes, but produces no error message.
    I print to XPS as a workaround since print to Adobe PDF never completes.

  • My HP PSC 1315 Cartridge Error Does Not Respond To Troubleshooting

    My printer  HP PSC 1315 has never given me problems. About a month ago I replaced the black ink cartridge (it was all I could afford). It was working fine and then out of the blue it came up with an error saying to check my cartridges. I did. Nothing obvious, so I ran the trouble shooter.... NO HELP! I REALLY need my printer in working condition ASAP!
    I tried removing the cartridge and put it back in. Then, did a reset by turning the printer off by pressing the "On/Resume" button  Then I removed the power cable and plugged it back in. I turned the printer back on using the "On/Resume" button that was used to turn it off.
    DIDN'T HELP!

    I've completed ALL of the following:
    HP SOLUTIONS
    I've even reset it and tried removing the black cartridge. I CANNOT afford a new one.... PLEASE HELP!!!!

  • 2110 printer ERROR message - remove and check cartriges

    I replaced black cartrige twice and still message - the color cartrige i did not replace however I'm only printing in black and have done this before with no problem- why cant i get this message to go away or am i missing somthing

    Hi @rem123,
    Thank you for visiting the HP Support Forums! I understand after years of non use, you put new cartridges in your HP PSC 750 and now you are getting a cartridge error message.
    I would like you to start troubleshooting here: 'Problem with Printhead,' 'Printer Failure,' 'Ink System Failure,' or a '0x...' or a 'C2...' Error M...
    Because there are many variations of these 'Problem with Printhead,' 'Printer Failure,' or 'Ink System Failure' error messages and alphanumeric codes, we have provided a few guided steps to get you to the right troubleshooting document for your error. Select the statement that best describes your situation.
    If you are still getting the error message after all the troubleshooting has been done, please contact our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
    http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
    I hope this helps!
    HevnLgh
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • Hp psc 1315 - printing photos - missing 1.4 inch at the bottom

    Hello,
    I'm trying tp print 4x6inch photos on my HP PSC 1315 on HP Photo Glossy Paper.
    No matter what software I try to print from, it always cuts off the last 1/4 inch of the photo and it comes out blank in that last 1/4 inch of the photo. 
    I'm using WinXP. 
    Does this printer have edge-to-edge printing capability? I saw that it was advertised as such.
    Is this a hardware or software error? Help please, i'm pulling my hair out!
    Thanks

    I beleive on this model you will need to use "tabbed" paper.  This has a 1/2" tab that is removed after printing to give borderless 4x6 prints.
    Regards,
    Bob Headrick, Microsoft MVP Printing/Imaging
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • Help on printing error messages to a log file

    Hi, may I know whether is there any way to print the error messages to a log file? Thanks for your help!

    noobboy,
    Please refrain from crossposting all of your questions into multiple forums. You were asked to stop this the last time you did this as well. Please be more considerate in future.

  • After upgrading to Lion, Printer error messages.

    After upgrading to Lion, I suddenly see the following error message whenever I print to my HP printer: "You can't open the application PrinterProxy because PowerPC applications are no longer supported." Now, my document will print, but I can no longer adjust settings. Help??

    PowerPC applications are no longer supported under Lion.  If you can't find Lion drivers on HP's website, you either need to go back to Snow Leopard or start looking for a newer, compatible printer.

Maybe you are looking for

  • Dvd Player Won't Play Copies Of Or Self-Made DVDS

    Macbook Pro 2.5Ghz with 10.5.5, and DVD player 5.0.1. Dvd player will play commercial dvds, but not any that I or anyone else has made. The same ones will play in my Mac Pro with the same settings. I tried many, but the common denominator is that it

  • Passing JAVA objects to different methods

    As you can see that "public static IntervalCategoryDataset createDataset()" want to get the data and attributes from storeStartDate and storeEndDate methods. i have class files, StartDate and EndDate that contains all the accessor methods. after i ha

  • Threads in while loop with two data acq loops

    Good day, I am using two while loops to perform data acquisition from two different pieces of hardware inside a "main" while loop - a total of three while loops. I want each of the data acq loops to run as fast as possible. With this model will each

  • Programmatically display one page as popup from one action of another page

    Hi, I'm using JDev 11.1.2.3.0 I have button action in page1.jspx, I wanna call page2.jspx as a inline popup when i run button action in page1. Because of my requirement, i don;t want to use dialog: as prefix in taskflow. Could someone tell me how i c

  • Can I do an operation in a bin?

    Can I do an operation between two different items from a dimension while I'm doing a bin of these two items? Thank you!