Psc1510 and duplex printing not working

I have windows 7 64bit and all is ok, but when I try to print with duplex setting, the printer start its work without asking me to reload the already printed page.
In XP, this feature works great.
thanks
Message Edited by axoduss on 10-05-2009 12:25 PM

He Daniel.
The standard HP ePrint feature does not support Duplex printing, I would assume that the same applies for HP ePrint Enterprise:
Are there any limitations that I should be aware of when using ePrint?
Duplexing (printing on both sides of the page) is not supported.
http://support.hp.com/us-en/document/c02882571
I suggest ensuring a such in the commercial forums, there are more expertize users for such a subject:
http://h30499.www3.hp.com/t5/HP-Designjet-ePrint-and-Share/bd-p/hp_eprint_and_share#.VPGA7oJOj5w
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Similar Messages

HP LaserJet 1320 Duplex Printing Not working with Windows 7

Hi
I've just bought a new PC with Windows 7 Home Premium. I have an HP LaserJet 1320 printer (Prod no. Q5927A, SN CNGW53RLRY).
I cannot find driver that works the same way as the previous driver HP LaserJet PCL5. If I use this driver and can still get duplex printing but it will only print one copy at a time.
If I upgrade to HP Universal Printing PLC (or PLC v5) I can print multiple copies but not duplex printing. I have searched high and low through the HP site but to no avail.
Any help and advice will be much appreciated.
Thanks
GB

Hello,
I've seen this same issue with my printers (other HP printers) whereby the default setting to support the Duplexing hardware was set to 'off'.
A quick method to check this is look at what the setting is for Duplex hardware in the Device Settings tab, and if it's not set, correct it.
Printer Properties:
From the 'Start' orb -> [Devices & Printers] -> right click on your Printer icon -> select 'Printer Properties' -> click on 'Device Settings' tab.
You should see a dialog similar to the mine (attached): look for the 'Duplex unit (for 2-sided printing)' and see if it's set to "Not Installed":
--> in either case, click on 'Not installed' and from the dropdown box, select 'Installed'... Click 'OK' to accept the changes and close the dialog.
Printing Preferences:
again, right click on your Printer icon -> select 'Printing Preferences' -> click on 'Advanced' tab.
-->Check to see if there is a 'Duplex Hardware' or '2-sided printing' option in here: mine doesn't show one but thougth I'd mention it nonetheless.
Click on the 'Finishing' tab and select 'Print on both sides'...or simply test print a multi-page document and set those preferences on-the-fly.
Let me know if this helps...
HardCopyTed
Regards,
HardCopy (I am employed by HP) [If this was helpful, please mark this 'Solved' or 'Accept as Solution' so others can find this too]
How to Give Kudos | How to mark as Solved
Attachments:
PCL6-DeviceSettingsScreenCap.JPG ‏81 KB

Automatic Duplex Printing not working on HP Color LaserJet 3600DN in Windows 7. It worked before.

I have an HP color laserjet 3600 DN on Windows 7. This computer came w/ Windows Vista and a 3600DN driver was installed and the computer was upgraded to Windows 7. The printer did automatic duplex printing.
At one point, my computer indicated that it could no longer find the printer. In an effort to solve this problem, I uninstalled the printer. When I tried to reinstall the printer the computer could not find the driver. At that point I tried to download a windows 7 CLJ 3600 DN driver. Since HP doesn't provide this driver for Windows 7, I tried to download the Windows Vista driver for 3600DN.
However, when I go to the appropriate webpage by following the links, only drivers for Color Laserjet 3600 are listed (no 3600DN drivers).
As far we can tell it only allows Manual Duplex printing (no automatic duplex printing). Clicking the "Two Sided Duplex Printing" option is there but only works when the "print on both sides (Manual)" is set on the Finishing page. If manual is turned off, then it becomes single sided.
Can I get a driver that will allow me to do automatic duplex printing on on my HP CLJ 3600 DN using Windows 7?

How did you replave the duplex belt? How to deassemble the backside of a officejet and click the new belt on? I can't see nor do it y self

HP Officejet Pro 8600 Duplex Printing Not Working

I am running Windows 7. Duplex printing is not working on my Officejet Pro 8600. It has worked in the past, but I cannot get it to work now. I have reset the printer and restarted by laptop. I have not made any changes that should affect the duplex printing. Thank you.

Hi there beachlover.
Hope you are doing wel and welcome to the HP forums;
The Hardware Diagnostic tool can help you find common hardware issues and in most occasions fix them Give it a try by going to this link www.hp.com/go/tools Let me know the results and include any errors that the utility finds
I will try my best to help you .
RobertoR
▼
You can say THANKS by clicking the KUDOS STAR. If my suggestion resolves your issue Mark as a "SOLUTION" this way others can benefit Thanks in Advance!

Officejet Pro 8600 Plus duplex printing not working

I am running Mac OSX leopard (10.5.8) and just bought the officejet pro 8600. Everything seems to work great except I can't figure out how to print on two sides. The option isn't allowed in page setup
I have checked the settings on the printer and can't see anything to indicate how to switch on the option for double-sided printing.
Thanks in advance for the help.
This question was solved.
View Solution.

Hi,
Please follow the steps below to configure the driver for automatic duplex printing:
1. Verify the duplex-printing accessory has been installed properly. To verify this open the System Preferences and go to Print & Fax. Open the print queue of your printer. Click on Printer Setup and from the tab menu choose Driver. Verify the box next to HP Two-sided Printing Accessory (Duplexer) is checked.
2. On the File menu, select Print. The Print window appears.
NOTE: The Print window might be minimized. Click the blue triangle next to the printer name to see all available settings.
3. In the expanded Print window you will find next to Copies the checkbox for Two-Sided. Check the box.
NOTE: If the checkbox does not appear within the specific application print dialog, skip this step.
4. To select the binding type click the lowest selection box listed as the name of the program (e.g. TextEdit)
Will appear as Copies & Pages within Microsoft Office applications.
5. Select Layout from the drop-down menu.
6. Set the Two-Sided option as Long-Edge binding (Portrait), or Long-Edge binding (landscape).
You may save the settings for future use by clicking Presets > Save Current Settings as Preset...
Please let me know of any problem,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Duplex Printing Not Working - Brother HL4570CDW

Hey all,
I managed to get a network printer setup and it works; however, the only thing that isn't working is duplex printing. I installed the driver from AUR: https://aur.archlinux.org/packages/brother-hl4570cdw/
In my default options I have "Two-Sided Printing" set to "Long-Edge Binding". But the CUPS printer page at localhost:631/printers/metafont (where metafont is the name/URL of the printer) shows me:
Description: metafont
Location: metafont
Driver: Brother HL-4570CDW series CUPS (color, 2-sided printing)
Connection: lpd://metafont/BINARY_P1
Defaults: job-sheets=none, none media=na_letter_8.5x11in sides=one-sided
What concerns me here is the sides=one-sided, I have a feeling that's a problem. In any case, I tried to print a PDF using evince and in "Page Setup" it tells me that the two-sided option is "Not available" and I also tried to print from the command line and adding the "-o sides=two-sided-long-edge" option but that didn't work either.
Any help would be appreciated!

He Daniel.
The standard HP ePrint feature does not support Duplex printing, I would assume that the same applies for HP ePrint Enterprise:
Are there any limitations that I should be aware of when using ePrint?
Duplexing (printing on both sides of the page) is not supported.
http://support.hp.com/us-en/document/c02882571
I suggest ensuring a such in the commercial forums, there are more expertize users for such a subject:
http://h30499.www3.hp.com/t5/HP-Designjet-ePrint-and-Share/bd-p/hp_eprint_and_share#.VPGA7oJOj5w
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

CP2025- Duplex printing not working anymore

I have been using for more than 8 month my CP2025 in duplex with very good results.
Nontehless, this last month I had only problem.
Printing in duplex, I have the first page well printed, and on the second page, it prints only the fist leaf and then stops. I have a message indicating a misprint (with no other information), I press OK, it restars for 2 pages.
That is very ... annoying.
Anybody had this problem?

He Daniel.
The standard HP ePrint feature does not support Duplex printing, I would assume that the same applies for HP ePrint Enterprise:
Are there any limitations that I should be aware of when using ePrint?
Duplexing (printing on both sides of the page) is not supported.
http://support.hp.com/us-en/document/c02882571
I suggest ensuring a such in the commercial forums, there are more expertize users for such a subject:
http://h30499.www3.hp.com/t5/HP-Designjet-ePrint-and-Share/bd-p/hp_eprint_and_share#.VPGA7oJOj5w
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

OfficeJet J6480 Duplex Printing not working

Duplexer is installed correctly with my OfficeJet J6480. When I try to print a two sided page using AUTOMATIC setting, it prints a page and pushces out the page without rolling it back to print on the other side. Any input on correcting this issue?
I have the latest drivers installed.

Hi, I had the same problem. There is a setting on the porperties page for your printer. Right click on your printer and select printer properties. When you get the properties page, select the Device Settings tab. Make sure the Duplex Unit (2 sided printing) is set to Installed.

Adobe Reader XI 11.0.10 duplex printing not working

I am trying to print a pdf two sided. My operating system is Windows 8.1 Pro and I am using the Xerox Work Centre 5875 printer. The settings on the print driver are set to default print 2 sided and in adobe reader two sided printing is checked off but it still comes out 1 sided. Printing double sided works in all other programs. Please help.

Hi satsugyo1,
For printing both sides, you might also need to enable 'printing on both sides' option in Reader print dialog box.
Please do the same and then print your PDF.
Let me know how it goes.
Regards,
Anubha

Scanner and Wireless Printing Not Working

Most of the features in my new printer are not functioning probley. The scanner does not work at all. Whether I'm using th wireless network or the printer is connected with UBS. Wireless printing is not working too. I don't know what to do. I tried to contact the customer support, but in order to do that, I had to provide the serial number. I put the number, but it said that they're unable to identify the serial number. Listed below all the information pf my frustrating printer.
My compurt is MacBook Air. OSX 10.7.5
Model: Deskjet 3050A J611
Serial No.: {Removed for privacy}
FPU No.: CR23164001

Hi Alsahafi,
I mention they were unable to verify the serial, was this a new in box printer?
Also, make sure you've installed the full feature driver for your OS X version, you can find this download here.
Don't forget to mark a post as solved if it fixed your issue

Web services and e print not working on 7520e

After the update it instructed me to turn off my printer so the update could take effect which I did but my printer would not turn back on. leaving it overnight it was the same the next day so I had to unplug it from the wall outlet. I lost my internet connection and no matter what I did I could not get it to connect.I called cloud services who put in a network address of 192.168.223.1 and hung up leaving me with no printer and sending me an email to get my ISP server to fix.
I called HP support and they got it connected just fine but when I try to log into my printers web page it still has my
hp email address but when I try to get to the web page it leads me to Launch HP network check.
on the front of my printer it says unable to connect to the internet, enter a proxy address, my server does not use one.
I tried to disable web services and then enabled them again hoping to get a new code but no luck. In my own network it has the last digit different to the one being used and set as a static IP address . I was not able to scroll any Apps before any of this happened, is the server down or has anyone any ideas how to fix this. has anyone else got the same problem. The schedulled Apps printed off just fine before this.

Hello dylon,
Thank you for being an active member of the HP support community. I understand that your Photosmart 7520 printer is indicating that it is not connected since doing a firmware update last week.
Please start by setting a manual IP address and manual DNS servers. Please use this post with the steps and screen shots on how to do this. The screen shots are for the Photosmart 7510 but the steps are the same.
If you find that you are still unable to connect to web services please call HP’s Cloud Services at 1-855-785-2777 if you live in the USA/Canada region. If you live outside the USA/Canada region please click here to find the Technical Support number for your country/region.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

AirTunes and USB printer not working?

Hi there-
This is probably (and hopefully) a simple problem to fix and I'm just being an idiot. Recently I moved and got myself an Airport Express to replace the Linksys that my old roommate took with her. It's been great, I got my network set up, I actually have a password now, everything. When I got it about a month and a half ago, I didn't have a printer or a way to plug my speaker to the Express, so I didn't bother with it.
Now I have both, but when I plug the printer or the speaker into the Express neither work. iTunes recognizes my base station, but no sound comes out of the speaker, and Word knows that the printer is there but when I print I get an error message saying it's not connected. I'm not exactly sure what to do. Poking through troubleshooting or Help doesn't work, so I'm hoping that I can get an answer here.
Thanks!

Hello Abby Waysdorf. Welcome to the Apple Discussions!
Let's double-check your AirPort Express Base Station's (AX) settings ...
Either connect to the AX's wireless network, or temporarily, connect directly (using an Ethernet cable) to the Ethernet port of the AX, and then, using the AirPort Utility (in Manual Setup), check the following settings:
AirPort - Base Station
o Base Station Name: <whatever you wish or use the default>
o Base Station Password: <enter the desired base station administrator password>
o Verify Password: <re-enter the base station administrator password>
o Remember this password in my keychain: (optional)
o Set time automatically: (optional)
o Allow configuration over Ethernet WAN port: checked
AirPort - Base Station - Base Station Options
o Contact: (optional)
o Location: (optional)
o Status Light: Always On (Default)
AirPort - Wireless
o Wireless Mode: Create a wireless network
o Network Name: <enter name or leave default>
o Radio Mode: 802.11b/g compatible
o Channel: Automatic
o Wireless Security: None
AirPort - Wireless - Wireless Options
o Multicast Rate: 2 Mbps
o Transmit Power: 100%
o Create a closed network: unchecked
o Use interference robustness: unchecked
AirPort - Access Control
o MAC Address Access Control: Not Enabled
Internet - Internet Connection
o Connect Using: Ethernet
o Configure IPv4: Using DHCP
o DNS Server(s): (optional)
o Domain Name: (optional)
o DHCP Client ID: (optional)
o Ethernet WAN Port: Automatic (Default)
o Connection Sharing: Share a public IP address
Internet - DHCP
o DHCP Range: 10.0.1.x
o DHCP Beginning Address: 10.0.1.2
o DHCP Ending Address: 10.0.1.200
o DHCP Lease: 4 hours
o DHCP Message: (optional)
o LDAP Server: (optional)
Internet - NAT
o Enable default at: unchecked
o Enable NAT Port Mapping Protocol: checked
Music
o Enable AirTunes (checked)
o Enable AirTunes over Ethernet (optional)
o iTunes Speaker Name: <enter desired speaker name>
o iTunes Speaker Password: (optional)
o Verify Password: (optional)
o Click Update to write the new settings to the AX
In iTunes:
iTunes > Preferences... > Advanced > General
o Look for remote speakers connected with AirTunes (checked)
Once you verified that you can get Internet access for all of your computers, you should secure your wireless network. To do so, I suggest that you make these changes:
AirPort > Wireless
o Wireless Security: WPA/WPA2 Personal
o Wireless Password: <enter your desired wireless network security password>
o Verify Password: <re-enter the wireless password>
o Click on "Update" to save the settings to the AX.

Duplex printing not working after installing HP Printer Driver Update 1.1.1

Hi,
our printers (Lexmark T622, HP Laserjet 2200, both equipped with a duplex unit) are managed by printer queues on our Mac OS X Server (10.5.5). Our users (mostly having Mac Books running 10.5.4 or 10.5.5) are printing by sending their jobs to the queues on the Mac OS X Server (via IPP/TCP/IP).
So far so good.
It seems that the users who have installed the "HP Printer Driver Update 1.1.1" aren't able to do duplex-printouts anymore. All sheets that leave the printers are printed on one side only - the "Duplex" setting by these clients is just ignored. Users who haven't installed the update yet, don't have the problem (at least it seems to me like this, but I have to admit that I've tested it with only three different Mac Books, yet).
My questions are:
- Has anybody else observed this behaviour, yet?
- Or, even better, does anybody have a solution to it? Reinstalling the printer on an affected client doesn't solve it. That's what I tried already.
- Is there any possibility to make the printer driver update "undone", which means to do a kind of downgrade from 1.1.1 to 1.1?
Thank you very much in advance!
Best regards,
Steffen

Hi,
it seems that
http://discussions.apple.com/thread.jspa?threadID=1715794&tstart=0#8157481
fixes my problem.
Best regards,
Steffen

Just upgraded to CS 4 and duplex printing no longer works

I'm trying to print a 2-sided document to an HP Laserjet 9500 from InDesign, and the duplexing no longer works. The printer still duplexes from my other Mac running CS2, so I'm wondering if something happened when I installed the upgrade.

I cannot get the dueplexing feature to work on our HP P2055 with InDesign CS3 & CS4 for the MAC.
HP P2055 Printer Driver from Snow Leopard.
From InDesign CS3 or CS4 (MAC) I send a two page Landscape document to duplex print. Only 8.5" from the left edge on both sides print. It's like it is only printing through a portrait mask.
Now if I make the document Portrait, then it prints fine.
The booklet printing is ever worse.
If I print with PCL instead of Postscript (Generic or the HP Postscript) the dueplexing works, but it prints the oppisite side flipped.
From a Windows Vista machine running CS2 everything works great.
On the MAC I can create a PDF from InDesign, open the PDF and duplex print the the same file fine.
On the MAC MS Word duplexes fine.
Anyone have insight on this InDesign/Printer issue?
24" iMac
Snow Leopard 10.6.1
Intel Core 2 Duo, 3.06 GHz
L2 Cache: 6 MB
Memory: 4 GB
Bus Speed: 1.07 GHz

HP Laserjet 1320 attention light on, printer not working.

I checked for paper jam, reseated printer cartridge, removed and reinserted printer and line cord plugs. Turned printer on and off. Attention light remains on and printer not working.

Hi Robert8695,
Let's manage one issue at a time. Regarding the error "unable to establish a two-way connection with the device", check out the link below for troubleshooting you can do to resolve it:
http://goo.gl/u3Snr
Let me know what happens and if the other problems persist as well.
If I have helped in any way, just click the Kudos star on the left. Also, if your issue has been resolved, don't forget to select Accept as Solution

Psc1510 and duplex printing not working

Similar Messages

Maybe you are looking for