PT880 Neo Audio+RAM help needed

Hi,
Last night I built my first computer (specs in signature). I installed XP Pro and its running, but I have 2 problems:
a) Back audio ports dont work
b) RAM is running in single channel mode (i bought a dual channel kit)
Im a complete newb, and i have no idea what im doing wrong, if anyone knows, or might know what im doing wrong, please post
THANKS A TON!
Thanks again,
MSIKid

Hello. I have this board too and the sound does not work from the back panel. I have checked the jumpers - they are correctly placed. I have also checked the BIOS settings to make sure that the onboard audio is enabled.
I do have a Sound Blaster Live! 5.1 Gamer installed in a PCI slot. Does this mean that the onboard audio will not work?
All I want to do is use the onboard microphone jack on the back panel with the SB Live for the sound output.
Anyone know why my audio does not work? Is it because of the PCI sound card installed? Can't I use both at the same time?
Thanks,
SkykingUSA
Quote
Originally posted by Del UK
Hi,
sounds like is second user mainboard and jumpers have been set to front panel..........please check booklet and check jumpers are set to back panel.....
Del
PS
Do you have a sound card installed into PCI or USB?

Similar Messages

PT880 Neo 4 red led, Need your help please!!

Hello all
It is my first post and I need your help. Today I purchased a combo P4 3/800 E Box CPU, MSI PT880 Neo FSR Mboard and DDR 512MB 3200 VS Corsair 400Mhz 184 Pin Dimm from Fry's Electronic. I can not get my system to boot , no beep but only 4 red led and nothing on the screen. I used on my system Enermax 300W with DVD burner, DVD player, 60G HD, SBlive 5.1, ALL in Wonder Radeon 32Mb..After I am following all recommendation in the defferents Topic, I have no luck it won't boot. The 4 red leds are still on. Help me please thank you
Brono85

I've just got my Noisetaker 470watts too, it has the same rails as CoolerGiant , but I like CoolerGiant's active cooling system for both CPU and PSU , just that it's too lengthy and my chassis was small in size .
Back to the topic, likewise anr11 mentioned, you may need a BIOS flash and you can use Memtest86 to test your RAMs out .

.MTS Audio Files help needed

I'm having a little trouble with editing.
The footage I am editing are .MTS files. Both the audio and video.
The video is playing fine (well, as best it can for my rubbish uni computers) but I am having trouble hearing the audio - and I'm getting lots of conforming errors.
I read here that CS4 doesn't support .MTS audio files. If that's the case then why can I hear some of them and not the others?
Should I be converting the audio into another format before editing? If so, then what's the best format to convert to, and how can I do it in a way that I don't have to strip the audio from the video (I want to keep them perfectly synced)
Thanks in advance for your help,
Nath

Hi Bill,
Thanks for your reply, that's an interesting article. The files I am editing are stored on an external hard drive - I tried deleting a few files on there to make some room (whilst I was in the editing suite) and it wouldn't let me delete them because it said I didn't have administrator permission - despite this being my own hard drive. Could that be causing a problem with conforming? Should I copy the files accross onto the internal drive? The scratch disks are set to the local D drive.
Nath
Ps: I've just downloaded a program which is converting the .MTS files into .MOV. I don't really want to do this as this will probably loose quality - but I'm trying everything! What would be the optimum file type to convert to?

Flash project audio button help needed

Hi,
I am just learning Actionscript 3 and trying to create buttons that turn a previous sound off before they turn a new one on. Also I want a button on the front that turns all sound off if it is pressed. I have attached my files in a zip folder.
The problem is all of my buttons which are inside movieclips just control the one sound. I have a couple more to do. I understand I will need an if statement but somehow I have to control all sounds and I don't quite get it.
I would really love someone to point me in the right direction. I cannot find a tutorial anywhere and am going crazy.
I look forward to someones reply,
Jan

Jay Robinson2 wrote:
I've just upgraded to Logic 7.2 as I bought an intel Mac. However, for some reason the audio plays through the macs built in speaker. I've got into preferences>audio>drivers and changed the driver to 'built in line input' but it's still playing through the speaker itself. I never had this problem while i was running previous versions on my old mac
When i boot up logic it does say something that i've never seen before which could be the cause...' Project Manager database on disk has got wrong version. Rescanning required'.
Any ideas?
G5 2.8 Quad Mac OS X (10.5.5)
Hi,
Try updating to 7.2.3
As far as the Manager... try doing a new expanded scan, overnight. This will update the database.
As far as the built in driver... you are selecting an INPUT.... and you expect it to change the OUTPUT??? Again, you are selecting an INPUT, while expecting the OUTPUT to change.
The Built in drivers have only 1 output available, And in your case, that is working as expected. When you want to RECORD via either input, that is when you change the driver. You should have two choices : Mic, and Line.
Cheers

Moving Clips - and how not to lose the audio? Help needed!

Hi,
I have used Premiere Pro 6.0 quite extensively over the years and have recently moved to Premiere Pro CS5.
With Premiere Pro 6.0 I could move/drag clips on the time-line and their linked audio would move with them. If I moved the video clip to another video track, say, above an existing clip, the audio would also move to a free audio track and not automically write over any existing audio. This would allow me to easily reorder clips on the timeline by simply moving them around and using other video tracks as temporary storage locations... and not lose or write over any other existing audio.
However in Premiere Pro CS5 if I do the same thing, the video will move to the other video track I move it to, but the audio will stay in the say audio track and will write-over any existing audio when the mouse button is released. The only way around this I can find in the manual is to: (1) drag the video to the other video track, and (2) press and hold the <SHIFT> key, whilst, (3) draging the linked audio to another audio track to avoid existing audio from being over-written.
My question: Is there a configuation I can set in CS5 to allow moving/draging of clips to work like in Premiere Pro 6.0? I have already messed up multiple times in CS5 by inadvertently over-writing existing audio.
Your expert advice and recommendations would be greatly appreciated.
THANKS IN ADVANCE.

Harm,
Your reply is not helpful. Just so you know, I have read through the manual extensively and could not find an answer for my question. AND that's why I brought my question here.
Perhaps I missed something in the manual. Would you mind re-reading my question and helping me if it is so easy?!
This has been frustrating for me for the last three months and I thought I would come to this forum for some expert advice. So far I have been told that CS5 is designed to be like this (does not answer my question), and now you tell me to look up the manual (again does not answer my question).
I'm amazed by responses that miss the question entirely and give helpful suggestions like that!

LPX audio transpose help needed...

So guys I noticed last night that anything that I turned into an apple loop I could transpose in the upper left drop down menu ( where quantize options are )
But I cannot do this with audio I record in until it has been apple looped and reimported.
Is there an option in recording pref's or anywhere that will allow you to record in a way that it codes the audio to be ready to transpose with out having to apple loop everything?
Thanks!

Audio recorded in the current Logic session, can follow tempo and can be transposed:
http://help.apple.com/logicpro/mac/10/#lgcpef37cd28
Unfortunately, the manual wrongly states that Transposition and Follow Tempo are only for Apple Loops...
http://help.apple.com/logicpro/mac/10/#lgcpf7c0af60

Front Panel Audio connection help needed

I own an MSI 790GX-G65 with Realtek HD audio, installed in an NZXT Tempest case.
Using the AC-97 plug from the case into the MB JAUD1 connection I get front panel headphone audio, but no mic input or automatic detection from the Realtek manager.
In short: Which plug(s) do I use on the MB socket JAUD1? I will detail my NZXT front panel connections.
NZXT Connectors:
Maxi Plugs:
HD Audio
AC-97
Mini-Plugs:
MIC-IN
Ground
L-Out
Ret-L
Ret-R
R-Out
MIC-VCC
FYI: I'm using Windows 7 64 bit. OS has been updated to current.
Thanks for your help.
Merry Christmas!
Robert

Ok. I checked and confirmed... I DID use HD Audio in JAUD1. I only thought I was using AC97... The problem still is:
Front Panel Headphones: Okay.
Front Panel Mic: Not detected at all.
Audio driver version is 6.0.1.6316
Audio Controller HD Audio
Audio Codec: ALC889
DX11
Window 7
Thanks for any further suggestions

MSI P965 Platinum frontal audio connector help needed!

Hi there guys,I recently brought a pc off craigslist and it came with this motherboard as described above.
My problem is with the front panel audio connectors.
The case of the computer is this one shown in this picture.
http://imageshack.us/photo/my-images/641/1304612874870.jpg/
Inside this pc case it has the following connector pins
1.SPK-R - white wire
2.SPK-L - red wire
3.GND - black wire
4.MIC bias - white wire
5.GND - black wire
6.MIC IN - red wire
This motherboard comes with a JAUD1 and a JFP2.Can anyone tell me where to plug those pins in for my front audio connector to work?
and I do have the manual.I think the problem is that the wires from the case is for AC97 but this pc is equipped with HD audio.
Thank you all for reading.

Quote from: cronnin on 06-May-11, 06:02:12
Your board is HD audio.
JPF2 should be for switches and LEDs as I recall, so go into JAUD.
Maybe this can help:
http://filedb.experts-exchange.com/incoming/2010/10_w43/360281/ac97.JPG
http://img.techpowerup.org/100423/HD%20Pin%20out.jpg
Some say that if you disable front panel jack sensing it may work, cause as you see from the diagram mic L/R and speaker L/R are on the same pins.
Some people get it working, and some have lot of noise..probably depends on the design of front panels PCB.
http://www.nitroware.net/index.php/editorials/67-articles/159-fix-broken-front-audio-ports.html
Probably the best way is to switch to AC'97 compatibility mode in BIOS?
http://www.ninjalane.com/images/lanpartyut-915p/bios_audio.jpg
Thanks alot cronnin.That was very helpful.My only problem now is that the AC97 plugs from the case has two ground.
Which one do I use and which one do I not plug in?
Also,I read on the internet,that plugging in ac97 plugs to HD audio connectors might blow up the motherboard.s that true?

Audio recording help needed

Is there a way to record audio from an external firewire device while recording the video from an isight camera? I'm creating online guitar lessons that would benifit greatly from a superior microphone rather than the isight camera mic.

Jazzer,
I don't think iMovie can deal with inputs from two different FireWire sources. Even if you try changing the sound input source in iMovie preferences it seems to have no effect.
Have you tried the iSight microphone?
I used it to do some voice over recording a while back and was very pleasantly surprised at it's quality.
Though the problem might be that the best placement for audio is not going to be the best for video.
Matt

Car audio upgrade help needed

I have a 2006 Chevy Tahoe and will be putting a new reciever in with usb input, jack input, and satellite ready. What else do I need for this install?

Hi wilmlow3,
It sounds like you've got it covered, but I would stop in and talk to the install bay tech and make sure. Nothing worse than trying to install car fi equipment and finding out you're missing something.
Good luck! And thanks for posting.
Marti|Social Media Specialist | Best Buy® Corporate
Private Message

K8T-NEO FISR2 -- RAM Help / Reccomendations please

Hi all,
I have a couple of unbranded 512M sticks of RAM at the moment in my machine, but I have some money burning a hole in my pocket, and so I was thinking of buying some performance RAM.
Firstly, how do I inspect my current RAM timings? in the BIOS it all says AUTO!?
Secondly, what would you reccomend for my new RAM?
Thanks
Rolfey

Thanks for your replys,
I won a couple of quid playing online poker, and that was why I fancied treating myself to a RAM upgrade. I wasnt sure what was best to get, so I posted here. I looked at lotta of the stuff available and noticed that the matched pairs of RAM had lower timings across the board, but it seemed it was designed for use on dual channel systems, and of course, mine isn't.
So, I made a compromise and went for some GEIL RAM that was on offer, I am hoping to sell my old RAM for about £50~£60, the GEIL stuff has cost me £80. I am currently running RAM with 3-3-3-8 timing set by SPD. The GEIL stuff I have bought suggests it runs at 2.5-3-3-6 at 400MHz, but once again, its a matched pair. I'll do a little benchmarking and see how it works out.
At the very least I can see if what differnece it makes if any, and give myself half a chance of an informed decision on my next RAM purchase if I am lucky at the poker tables again!!
Thanks, Rolfey out...

Pt880 neo lsr - ethernet help

okay I've tried everything, power cycling my modem/router and even formatting my computer.
this piece of ethernet is pissing me off. I have a linksys router btw.
I can get on the internet with my old computer but not the new one.
VIA RHINE II

eheh.... maybe you just haven't configured it to run yet. :P Be patient ok?
what's your full system spec?
HAve you got all the necessary drivers installed?
Have the onboard LAN detected in Windows?
Have it got any IP?

PT880 NEO need help ASAP

Hey guys, im helping a friend of mine build a computer, now we got it together and it fails on, Testing base and extended memory, we have tried various rams and it always fails there, so it isnt a ram issue, we have a new CPU so i doubt its that either,
the things i have narrowed it down to are.....
1. PSU , 18a on 12v
2. Motherboard
3. RAM - doubt it highly
sys specs are
420w psu 18a on 12v
333 RAM, various brands tested
MSI pt880 neo
P4 3.0e HT 800 FSB
please help asap

Hey guys
I had a lot of trouble with my MSI PT880 Neo FSR, P4 3GHz (Prescott), 2x512MB dual Channel (GEIL)
I used to have bios v.1.9
I contacted MSI USA and explained the following issue:
play for 5 min HL2 and have a memory allocation error
play BF1942 for a little while (15min?) and computer crash
enable Dual mode for my memory and computer crash working with Word lol
They have just sent me a new bios v.2.3 and guess what ??? After long tests my computer never crash and I am the happiest man in the world cause now I could spend more time with my girlfriend lol
So try to contact MSI to have this latest bios or reply to this thread and i will try to send it to you
enjoy your games and still give your feeback about MSI products

Pt880 Neo will not boot. Help please

Here is my setup. I just picked up a brand new msi pt880 neo series and a p4. 2.8 fsb800/1mbcache.
I was current using a ati 9800 pro and crucial 512 pc3200 ram. i installed two maxtor 160g hd and i was going to run raid in a pci slot raid controller. so far i know the ram works and the video card and the one of the hd. My power supply supports up to 400watts. I have a btc dvd burner, floppy and a liteon dvd rom. im also running 4 fans.
My problem is that when i turn it on, it powers up but nothing else works. On the D-bracket 2 i get 4 red lights lite up and nothing else.
Im stuck and not sure what to do now? Is it my mb or chip or a combination of things? Thank you very much for your time.

Heya,-
Sounds interesting enough to me aswell... I had the same problems with my Mobo too... But it turned out to be the CPU. Intel has release some 'C' versions of that 2.8GHz CPU, which might be some scaled-down Extreme Edition CPU's or even a down-graded Prescott CPU.
So what I needed for my mobo to get it work was:
- Updated BIOS version
- Another CPU (working) to get the new BIOS version on my mobo...
The shop that helped me, gave me some information from Intel. You can check your exact type of CPU in their website... They gave me the link to the Intel P4 CPU Specification Update. And in that document on page 17 I found out that my CPU with package ID: SL6Z5 is in fact a down-graded Extreme Edition CPU, and should have been sold as a tray-CPU, and not as a boxed CPU... DAMN INTEL!... But anyway, they gave me a headache and some nights of incredible sleeplessness...
Just for your information... This is how I found out that it was my CPU causing all this problem:
- Assemble the system with only mainboard and PSU (no memory, no vga, no keyboard)
- Connect the CPU fan to see if the system will start running
- Turn-on the system and see if the CPU fan will keep running
- Shut down the system
- Insert the CPU
- Turn-on the system again... If it fails on your CPU, it should shutdown after 5 seconds...
> To find out if it's related to any of your other peripherals, insert all the things step by step (first memory, then vga, etc...) and see if your system will fail on any of these peripherals.
It just might turn out to be a harddisk that's drawing too much current from your power-supply....
ANyway, just to share some thoughts! Good luck!

Warning "RAM Preview needs 2 or more frames" after scrubbing audio in After Effects CC 2014 (13.0)

The After Effects team are investigating a bug in After Effects CC 2104 (13.0) where a memory leak occurs while scrubbing audio (holding down the CTRL or Command key while scrubbing). This memory leak can eventually consume all free RAM, which can lead to the warning message "After Effects error: RAM Preview needs 2 or more frames to playback" when you try to initiate a RAM preview.
While we investigate this problem, you can avoid the bug and memory leak by not scrubbing with audio. When the problem occurs you can resolve it by closing and restarting After Effects.
http://blogs.adobe.com/aftereffects/2014/07/warning-ram-preview-needs-2-or-more-frames-aft er-scrubbing-audio-in-after-effects-cc-2014-13-0.html

Hi all, just wanted to say, I am currently working on an award show for TV and have been scrubbing audio in AE CC 2014 13.0.2.3 without issue. Why am I not having the memory leak problem?
Would like to help if I can.
Hardware Overview:
Model Name: Mac Pro
Model Identifier: MacPro6,1
Processor Name: 12-Core Intel Xeon E5
Processor Speed: 2.7 GHz
Number of Processors: 1
Total Number of Cores: 12
L2 Cache (per Core): 256 KB
L3 Cache: 30 MB
Memory: 64 GB
Boot ROM Version: MP61.0116.B05
SMC Version (system): 2.20f18
Illumination Version: 1.4a6
System Software Overview:
System Version: OS X 10.9.4 (13E28)
Kernel Version: Darwin 13.3.0
Boot Volume: Macintosh HD
Boot Mode: Normal
Computer Name:
User Name:
Secure Virtual Memory: Enabled
Time since boot: 1 day7:24

PT880 Neo Audio+RAM help needed

Similar Messages

Maybe you are looking for