Pulsed Multitone Signal for RFSG

We tried combining the sample codes provided with NI LabVIEW 2013. We tried integrating the RFSG Pulsed Data VI and the RFSG Multitone - Uniform Spacing VI, and we seem to be producing noise.
We're currently using a single RFSG (NI PXIe-5673) and a single RFSA (NI PXIe-5663) in an 18-slot PXI chassis (PXIe-1075). Since we are pulsing the Multitone signal (in this example, a dual tone), the received signal is not we're expecting.
Attached in a zip file are the reults and the codes that we've used. The signal was transmitted using the Pulsed_Multitone VI and was received and analyzed using the RFSA IQ Graph VI. What are we doing wrong? Or is there a better way to do it?
Attachments:
RFSG-RFSA Files.zip ‏117 KB

Hi,
Thank you for including the screenshots. I think the first thing to try would be running a simple test in the Soft Front Panels with a single tone to see if you see the same behavior. If you are able to run this successfully, try a multitone in the SFP. This will help us determine if it is a hardware or software issue. Please feel free to upload screenshots of these tests and I would be happy to take a look.
Best regards,
R. Brill
Applications Engineer
National Instruments

Similar Messages

  • How can I record multiple signals for a long period of time?

    Hi, everyone
    I am new at labView I just recentlyl started using it. Right now I am working on this assignment
    that I have to display en record six different signals comming up from a DAQ. so basically What I did
    for my IV is placing a whileloop. Inside the while loop I set up the DAQ assistant and then I send that
    to a split signal function in order to split the signas that are comming from the DAQ ( so those signals
    are EMG1,EMG2, blood flow1, blood flow2, blood pressure, and AM stimulation) after I split the signals
    I send each individual signals to a waveforme graph, but my problem is that I need to record those individual
    signals for a long period of time every second for about 8 hours. so it will be really helpfull if someone can
    guide me through this. Thanks
    Regards

    Hi,
    With your while loop, you'd better use low-level VIs to write your data to a file. Please see attached...I've used text file function but if you need ta save a large amount of data, you may need to use binary file functions instead (nearly the same way to perform this whatever you chose text file or binary file function).
    Best,
    J.
    Attachments:
    RecordData.vi ‏27 KB

  • Can I set up to connect 2 or 3 airport expresses to have a stronger wifi signal for a larger area?

    can I set up to connect 2 or 3 airport expresses to have a stronger wifi signal for a larger area?

    Theoretically yes. It will really depend on your situation. Please review the following Apple Support article to understand what is possible with the AirPort base stations and post back with any questions or help in setting up your extended network.

  • HT5594 I have lost my I phone5 amd I have enabled lost mode. But still I can't find out where it could be and I cloud search gives offline signal. If the thief turns on my phone is it possible to find out my phone or given any signal for me?

    I have lost my I phone5 amd I have enabled lost mode. But still I can't find out where it could be and I cloud search gives offline signal. If the thief turns on my phone is it possible to find out my phone or given any signal for me? is it possible for the thief to use or sell my I phone even it is on the locked mode by ICloud?

    If it is turned on and your lock request is able to be fulfilled, a confirmation email will be sent to your Apple ID email address. There isn't any known way to bypass Activation Lock on your phone so no one will be able to use it. More information on Lost Mode: http://support.apple.com/kb/PH2700

  • How can I get 'sync' signals for sine wave out? [FPGA USB 7856R]

    Hello,
    I'm Sean Ahn using NI 7856R, USB FPGA with LabVIEW 2014.
    I'm trying to make 'sync' signals for sine wave of adjustable frequency, like general function generator's sync out.
    I use sine waves whose frequency is feedback-congtrolled between 25~30 kHz and need sync signals of square wave.
    Like [1] below, when I try resettng two wavefom-generators, sine and sync signals are not perfectly synchronized.
    And everytime I adjust sine's frequency, the phase difference between sine and sync changes arbitrarily 
    In case of [2] using 'zero-crossing detector', I have severe jitter of sync signals not suitable as 'sync' signals for other parts.
    Please, give me some help.
    Thanks in advance
    Sean Ahn
    [1] Reseting two waveform generators
    [2] Zero-crossing detect

    Here’s my issue.  When I try to move any data between my PC and the iPad2 I receive an error message that states that “the [sync] session could not be started with the ipad, Please disconnect and reconnect the iPad and try again”
    I have tried again and again by various methods etc .  and all I get is the same message when I attempt to sync, backup or update the iPad. 
    I have tried the following AND FAILED:
    Deselect all Apps, Music etc in iTunes, then attempt to sync
    Disable and enable the iPad in device manager and restart itunes and try to sync again
    Disable and enable Apple Mobile Device Services and sync/backup/update
    Run iTunes as Administrator
    Reboot all devices (iPad buy pressing two buttons at once)
    Turn off all security and reboot and sync
    Connect directly to internet without a router
    Tried to sync with all wireless turned off and in airplane mode
    Running iTunes Diagnostics...... nothing all test passes
    Changing USB ports and cables
    Removing my SIM card and rebooting and trying to syc
    Trying to sync via wifi only
    Turning off all icloud services
    Uninstalling all Apple Software and reinstalling again
    I am syncing to a 64bit  PC running Win 7 Premium with all the latest updates, all firewalls off. WiFi and direct connect ethernet to Internet service with and without router.
    I am trying to Sync an iPAD 2 running iOS version 5.1.1 (9B206)
    I am trying to update from iOS 5.11 to 6.01 by using Itunes 11.0.0.16.3 in a USB or directly through the iPad via wifi.
    Please help as everything I have tried has failed.

  • Is it save to use digital output as a digital input signal for another channel

    Hi all,
    I know this is a stupid question, but I do not have other signal generator by hand. So what I want to know is, can I use the digital output signal of my USB-6001 as an input signal for the same device but on other digital port? I did not try out directly because I do not want to burn the device down......
    Thanks
    Solved!
    Go to Solution.

    I do loop backs all the time, especially in my test systems as a way of making sure my signal is making it to the UUT pin.  I typically throw in a 10k resistor just in case, but I have never had an issue.
    There are only two ways to tell somebody thanks: Kudos and Marked Solutions
    Unofficial Forum Rules and Guidelines

  • Can I get an Ipad with wifi and cellular but no contract with a carrier in the US?  I want to use it overseas in Africa with a local SIM card and use the cellular signal for all my internet.

    Can I get an Ipad with wifi and cellular but no contract with a carrier in the US?  I want to use it overseas in Africa with a local SIM card and use the cellular signal for all my internet. 

    Yes you can.  All Ipad's are unlocked and can be used any where in the world. Buy the AT&T version which is GSM in other countries

  • How to use startscan signal for triggering for E-series DAQ

    Hi, I want to collect the engine cylinder pressure data with a PXI-6070E DAQ card and BEI Encoder. I want to use the TDC signal as trig1, and crank angle signal as startscan for triggering. Could anybody give me an example or suggestions about doing this in labview. I cannot find any example that uses startscan signal for trigging. Thanks.

    There is an example VI that is installed with LabVIEW. It is called "Cont Acq&Graph ExtScanClk D-Trig.vi" and it is located in the following LLB.
    \Examples\DAQ\anlogin\anlogin.llb
    Your project aligns very closely with a past project of mine. If you require professional expert assistance, feel free to call on us.
    Daniel L. Press
    Certified LabVIEW Developer
    PrimeTest Corp.
    www.primetest.com

  • Can my Airport Express be used to extend the signal for an iPad2

    I am using a Linksys wired router as the beginning of my home network. There is an ethernet cable running from it through a wall to the Xbox 360 and an Airport Express serving as the base for the wireless network. I have an iBook on the other side of the wall and about 10 feet and an iMac about 20 feet with one wall in between. These two have some fluctuation in their signal but only between 4 bars and 3. I just got an iPad 2 and it is causing me grief because it struggles to maintain a connection just another 10 feet from the iBook. If I put it next to the iMac when it has full 4 bars the iPad gets maybe 2. The iPad has full bars if next to the router. That kind of defeats the purpose of buying an iPad. So, my question is how to rearrange the network so the iPad is happy in the living room where I mostly use it. I had considered moving the iMac and using it as a base station to free the Airport Express for other duty but where I want to move it is further away from the living room. Right now the Airport is wired to the router. Is this necessary for it to be a part of the network? I know I can use it to get music from iTunes to speakers but would that placement also work as a wireless extender? Would just buying another router for the Xbox location and putting the Airport there also be a better solution?

    ladybastet, let's clean up some terminology. You should designate only one router for your network. At present that is the Linksys. Your wireless access point is the Express, and it gets its network connection from the Linksys. Is that correct?
    If I put it next to the iMac when it has full 4 bars the iPad gets maybe 2. The iPad has full bars if next to the router.
    Now that you know your Linksys is the router, is the above correct? Unless the Linksys is also a wireless access point, the iPad's proximity to it will not matter. Only its proximity to the device creating the wireless network is a factor. In your case, I believe that is the Express.
    There is an ethernet cable running from it through a wall to the Xbox 360 and an Airport Express serving as the base for the wireless network.
    I'm not sure I understand. Is one Ethernet cable going to two places? What is it connected to, precisely?
    Right now the Airport is wired to the router. Is this necessary for it to be a part of the network?
    In the case of a wired router, yes.
    I'm wondering if you have things configured properly, particularly if you have configured the iMac to share its network connection over AirPort. I'm even wondering if your iPad has unintentionally joined a neighbor's wireless network.
    I had considered moving the iMac and using it as a base station to free the Airport Express for other duty but where I want to move it is further away from the living room.
    Using the iMac to share a wired Ethernet connection to create its own wireless network is certainly possible, but it is less than ideal. For one, the iMac would have to be powered on all the time.
    You do not need or want another router.
    It is impossible for me to be certain of your network environment (meaning, the size and configuration of your home, the proximity of competing wireless networks, the number of network devices, and the potential for interference) but you might be better off replacing the wired Linksys router with an AirPort Extreme. That would give you the ability to create a "roaming network" or to use your Express to extend the Extreme's wireless network. I think this would be the easiest solution, but given the uncertainly of your description this expense may not be necessary.
    Much of my confusion stems from your original question: "Can my Airport Express be used to extend the signal for an iPad2" - the quick answer is yes, but a prerequisite question is, "what signal?" The only "signal" I can determine that may be relevant is the one created by the Express. Once we have the terminology fixed, perhaps we can fix what's wrong with your network.

  • Making different signals for different color average of the pixcells

    Hello, everyone.
    I'll take image of paper money by webcam,
    and get the color average of the bills
    and fractionate the color average by wavelength range of each bills.
    and I want to making signal releasing time differently for different color average of the pixcells.(to fractionate the kind of bills)
    (I want different signal for different kind of bills) 
    my question is this:
    (1)How can I connect the webcam to the Labview?
    (2)How can I get the color average of paper money?
    (3)How can I make Labview program for releasing different signals which has different releasing time for each color average?

    Hi 박지성,
    you can use the IMAQ for USB Driver. See this link http://zone.ni.com/devzone/cda/epd/p/id/5030. You can also use the integrated windows dll to get your picture.
    Hope it helps.
    Mike

  • Failed to send start signal for complete cluster, SLD may still be stopped.

    Hello,
    I am trying to create technical systems in the SLD on the portal (http://host:port/sld). It prompts me to start the SLD server by going to Administration.
    When I click the button "Start Server" under Administration, I get this following error message:
    "Failed to send start signal for complete cluster, SLD may still be stopped on other cluster nodes."
    Can you please tell me what has to be done to successfully start the SLD server so that I can go ahead and add technical systems.
    Thanks
    Srinivas

    Hi Siddarth,
    I checked MMC. There is only one instance running.
    Here is the structure in MMC.
    Database
    Instance 0
    Instance 1
    Instances are green and running.
    Here is log on the server:
    #28 12/12/2008 07:43:44.413 [SAPEngine_Application_Thread[impl:3]_15] FATAL com.sap.lcr.start.StartDirector: SLD start failure, unable to activate the SLD CIMOM. Check the log of the persistence medium for any errors. If the error is reproducible, please send a message to SAP. More...
    #27 12/12/2008 07:43:44.397 [SAPEngine_Application_Thread[impl:3]_15] FATAL com.sap.lcr.objmgr.core.TransactionContainerChangeBuffer: Storing changes to cache failed. Please restart the application to reinitialize the cache.(Error: CIM_ERR_FAILED: Failed to initialize cluster notification sender.) More...
    #26 12/12/2008 07:43:44.382 [SAPEngine_Application_Thread[impl:3]_15] ERROR com.sap.lcr.cimsrv.ClusterNotificationSender$JMSSender: Failed to initialize cluster notification sender. Please check your JNDI service and JMS provider for errors. More...
    #25 12/12/2008 07:43:44.288 [SAPEngine_Application_Thread[impl:3]_15] ERROR com.sap.lcr.webui.CimIO: Failed to send start signal for complete cluster, SLD may still be stopped on other cluster nodes.
    #24 12/12/2008 07:43:44.288 [SAPEngine_Application_Thread[impl:3]_15] ERROR com.sap.lcr.cimsrv.ClusterNotificationSender$JMSSender: Failed to initialize cluster notification sender. Please check your JNDI service and JMS provider for errors. More...
    What could be the problem.

  • When listening to music with my apple tv, I lose signal for a few seconds, then its okay and then I lose it again... any solutions ?

    when listening to music with my apple tv, I lose signal for a few seconds, then its okay and then I lose it again... any solutions ?

    Hi there Iphone4fn,
    I would recommend taking a look at the troubleshooting steps found in the article below.
    iOS: Unable to update or restore
    http://support.apple.com/kb/HT1808
    -Griff W.

  • HT201342 Hi , I want ask you about imessage some time my account not availability and signal for calling some time no signal on my iPhone only search the signal , all pra

    Hi , I want ask you about imessage some time my account not availability and signal for calling some time no signal on my iPhone only search the signal ,

    I have taken it back to the Apple store genius bar, but they say they don't see anything wrong. Well unless you use it all day and experience the problems when they happen, you wont see anything wrong. But there are lots wrong with it. But this would be the same store as I purchased the phone. And they backed up my old Iphone 4, but were not able to get anything to load back onto my new phone. So, I lost pretty much everything. But over time, some of my contacts have started showing up, although i am still missing over 800 of them.

  • 12VDC for Limit and Home Signals for PCI 7334 using UMI-7764

    Can 12VDC be used for Limit and Home Signals for PCI 7334 using UMI-7764.
    Can the UMI 7764 be damaged if over voltage is supplied to it. If so can it be repaired or it has to replaced.

    Specifications for the Limit Switchs (home, forward, reverse, etc) is
    determined by the specifications of your NI motion controller PCI
    board. The UMI functions only as a pass through and breakout for the
    board .
    The valid limit swich voltage for the PCI-7334 is 0 - 5 V. You will have to divide down a 12 V input before running it to
    the UMI and to your board. The 3.3k pull up resistor is only used to
    pull floating voltages to TTL levels and does not protect for high
    voltage signals.
    Please note that the UMI-7774 provides optical isolation for limit switches and extended input levels (e. g. limit switch voltages: On = 3.5 to 30 V, Off = 0 to 2 V).
    Best regards,
    Jochen Klier
    National Instruments Germany

  • Have one WiFi signal into the apartment for my Air, and another wifi signal for my 5c phone plan. Both from the same provider. Expensive. Is there a way to 'combine' WiFi signals so I pay only for one, but can get on the Internet with my Air?

    Have one WiFi signal into the apartment for my Air, and another wifi signal for my 5c phone plan. Both from the same provider. Expensive. Is there a way to 'combine' WiFi signals so I pay only for one, but can get on the Internet with my Air?

    Roamingnome, thanks for your response. Although I have been a Bell (Canada) customer for my WiFi signal for years, the 5c and its necessary mobility plan, is very recent. Some years ago, Bell supplied its own ‘router’ for my computer, and claimed that it was possible to get their WiFi signal only with the router they supplied. When I recently received the 5c, I wondered if the plan it requires, which is within the much wider, overall Bell zone, could be used somehow to get my Air online - some sort of tethering? - that allows me to give up the Air WiFi service and router all together, but still get the Air connected. Here in Canada, Bell Mobility and other Bell services are very separate. Any suggestions appreciated.

Maybe you are looking for