Push-Pull Inverter and Transformer Problems

Hi,
I’m new to the forums and wonder if someone can help me with a Multisim problem.
Basically I’m designing a simple push-pull inverter comprising of a transformer with a centre tapped primary winding (TS Power), a 24V DC supply and two MOSFETS.
The centre tap of the transformer is earthed and the 24V DC supply is connected to the two outer ends of the primary winding via each MOSFET.
I’ve constructed a 555 timer circuit to provide a pulse train to fire the gates of each MOSFET in turn.
My problem is that although I get the desired secondary waveform output (modified sine wave) the voltage magnitude doesn’t appear to relate to the transformer turns ratio?
Am I doing something wrong?
Many thanks for any advice in advance.

Hi Woody,
Thank you for your post and welcome to the forums. Please could you attach your circuit schematic to a reply post, I can then simulate your circuit myself and make suggestions where necessary.
Many Thanks
Jamie S.
Applications Engineer
National Instruments

Similar Messages

How to create a push pull list?

I am trying to create a push pull list and thought there was some easy way to do this? I have looked everywhere and can't find anything about these.
I just want to be able to do something similar to the push pull found in the master detail wizard when you push columns over to display.
Do I need custom javascript for this?

Follow these steps in htmldb:
Create New Page
Form
Master Detail Form
Then select a table in your schema
There are 2 boxes below - available columns and displayed columns. You can use the buttons in the middle to push and pull (or add and remove).
This is what I call a push pull list and I assumed that as it was used here then the same functionality is available for use elsewhere (like in a wizard for an item maybe).
Hope this makes more sense

When receiving an call waiting can't push the hold and answer button.Because: it will put on hold the first caller, answer to the second, but you can't hear the second until you end the first call !!! Anyone has the same problem ? Did anyone know why ?

When receiving an call waiting can't push the hold and answer button.Because: it will put on hold the first caller, answer to the second, but you can't hear the second until you end the first call !!! Anyone has the same problem ? Did anyone know why ?

Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact

Pull-DP and BITS Download Problem

Hi,
We have a ConfigMgr 2012 SP1 primary site, a remote Pull-DP and a remote DP with MP in untrusted forest, working on Windows Server 2008 R2 SP1.
DP replication works well if I use primary site server as a source but it doesn't work if I use remote untrusted DP as Pull-DP source. I've read that it supported scenario to use untrusted DP as a source DP.
Here is an error that I came accross and the troubleshooting steps I've tried:
When I run "bitsadmin /list /allusers" command it shows "TRANSIENT_ERROR"
{92047230-0551-4147-A70B-9511CB0304E1} 'CCMDTS Job' TRANSIENT_ERROR 0 / 1 0 / UNKNOWN
{8C41095C-2CAD-44A9-850C-E8E4C8717508} 'CCMDTS Job' TRANSIENT_ERROR 0 / 1 0 / UNKNOWN
{0FC95025-ADEF-4C25-A154-D3946E8B1DC6} 'CCMDTS Job' TRANSIENT_ERROR 0 / 1 0 / UNKNOWN
Listed 17 job(s).
Here are the details of one of the BITS download job,
GUID: {C7956199-77B1-49D0-BF22-6A528D14E7BE} DISPLAY: 'CCMDTS Job'
TYPE: DOWNLOAD STATE: TRANSIENT_ERROR OWNER: NT AUTHORITY\SYSTEM
PRIORITY: HIGH FILES: 0 / 1 BYTES: 0 / UNKNOWN
CREATION TIME: 12/9/2013 4:35:22 AM MODIFICATION TIME: 12/10/2013 9:03:20 PM
COMPLETION TIME: UNKNOWN ACL FLAGS:
NOTIFY INTERFACE: REGISTERED NOTIFICATION FLAGS: 11
RETRY DELAY: 60 NO PROGRESS TIMEOUT: 3600 ERROR COUNT: 344
PROXY USAGE: NO_PROXY PROXY LIST: NULL PROXY BYPASS LIST: NULL
ERROR FILE: http://SCCM01.DOMAIN.COM:80/SMS_DP_SMSPKG$/df3b2329-d034-4d87-9fbd-3940d8e2685c/sccm?/NIS_Delta_Patch.exe -> C:\SMS_DP$\CH10000A\df3b2329-d034-4d
87-9fbd-3940d8e2685c\NIS_Delta_Patch.exe
ERROR CODE: 0x80070003 - The system cannot find the path specified.
ERROR CONTEXT: 0x00000004 - The error occurred while the local file was being processed. Verify that the file is not in use, and retry.
DESCRIPTION:
JOB FILES:
0 / UNKNOWN WORKING http://SCCM01.DOMAIN.COM:80/SMS_DP_SMSPKG$/df3b2329-d034-4d87-9fbd-3940d8e2685c/sccm?/NIS_Delta_Patch.exe -> C:\SMS_DP$\CH10000A\df3
b2329-d034-4d87-9fbd-3940d8e2685c\NIS_Delta_Patch.exe
NOTIFICATION COMMAND LINE: none
owner MIC integrity level: SYSTEM
owner elevated ? true
This job is read-only to the current CMD window because the job's mandatory
integrity level of SYSTEM is higher than the window's level of HIGH.
Peercaching flags
Enable download from peers :false
Enable serving to peers :false
CUSTOM HEADERS: NULL
I've checked C:\SMS_DP$\CH10000A\ folder and permissions everything looks okay.
I have used psexec to run command prompt with SYSTEM account and tried to download the same file to the same folder,
bitsadmin /create TestJob
bitsadmin /addfile TestJob http://SCCM01.DOMAIN.COM:80/SMS_DP_SMSPKG$/df3b2329-d034-4d87-9fbd-3940d8e2685c/sccm?/NIS_Delta_Patch.exe C:\SMS_DP$\CH10000A\test.exe
bitsadmin /resume TestJob
The file is downloaded without an error so I have no idea why BITS can not download the same file from the same source :/
Thanks

Since no one has answer this post, I recommend opening a support case with CSS as they can work with you to solve this problem.
Garth Jones | My blogs: Enhansoft and
Old Blog site | Twitter:
@GarthMJ

LG Ally text message and gps problems

hello. ive been with verizon for about 10 years maybe. ive been overall happy with the service and customer service. but the prices should be alot lower.lol. i started out with the motorolas then switched to the lg phones. only problem with the motorola was the speakers. not loud enough. could never hear the phone ring. the lgs usually suffer from the same problem.
i had a few phone problems but nothing like this lg ally. im on my second one and about to be my 3rd one in about 3 months. 1st phone i had every problem under the sun. this phone i am suffering from text message problems and gps problems. i suffer from what everyone else has problems with. the messages wont send. they will eventually lock up. it will show the envelope with the red explanation point ( i think thats the graphic). then usually everytime when i sent a text the texts will close. it will send then bounce back and show up as a draft and i have to resend it and wait for it to go thru. finally the last problem with the texts. when i send a text a phone number from my contacts shows up and freezes on the screen. its in white text with a black background. its the same number every time. it stays on the screen until i restart or pull my battery out.
gps. when i open up google gps that comes with the phone i make sure the gps is on... when the directions are found and the map pops up 9 out of 10 times it just keeps saying searching for gps. the turn by turn never is found. the 1 time it does it takes a good 10 minutes to be found. atleast on my first one ally the gps did work 8 out of 10 times. it just took a good 5-10 minutes for gps to be found and show turn by turn.
anyone else have these problems? where you able to fix them or did you need to get a new phone? the 2.1 update was supposed to fix problems. i think they just made it worse. the ally is supposed to have 2.2 froyo. where is it. is it ever going to get it. i got this phone because i like the lgs and the keyboard. also the sales representative on the phone was giving the lg ally rave reviews. why couldnt he say dont buy this go with a motorola droid. this phone is the biggest junk ever made

I do apologize you are having trouble with your device I looked in our information system on the LG Ally in reguards to issues you are having it states if you have the Free Droid Security anti virus protection application down loaded it will cause the phone to lock up or freeze. Check and make sure you do not have the application on your device. Check you GPS settings and make sure correct. Go to Settings; Location & Security; make sure GPS is on wireless network. If this does not fix issue you can try doing a Master Reset on your device. Make sure your contacts are saved in your G-mail account or through Back Up Assistance.
Master Reset/Soft Reset:
Factory Reset option 1
From the main screen, touch menu tab
Touch Settings
Touch Privacy
Touch Factory Data reset
Touch Reset Phone
Warning: This will erase all data from your phone, including:
Your Google account
System and application data and settings
Downloaded Applications
It will not erase: Current System software and bundled applications; SD Card files, such as music or Photos
Factory Reset option 2 - Warning this will reset device back to original factory settings.
Turn off the phone
Press and hold "home" + "end" + "volume up or down" keys together for a few seconds when the device is power off
Once device displays boot information, release keys.
Soft Reset
Press the Power key.
Touch Power off.
Touch OK.
Press the Power key to power on the device.
or
Remove battery cover, remove battery and reinstall.Also there is a new update for LG Ally it will be the Froyo 2.2 but there is not release date available at this time it will post on your device when available. Hope this Helps. Leslie

No Battery Charge and Other Problems After OS3 Install - Solution?

This relates ONLY to iPhone Users using the "PUSH" Function for Email or Other Apps!
PROBLEM: It seems as though Apple is at least aware of the problem(s), i.e. once Exchange Email or another App using PUSH is configured, there is an OS3 bug that seems to be hardware independent (impacting ALL 1G, 2G and GS iPhones, but not consistently).
SYMPTOMS: Include some or all of the following . . . rapid discharge (less than two hours from a fully charged phone, failure to charge (by AC adapter or USB to computer), failure to charge completely, perpetual dead battery icon, inability to boot, inability to automatically sleep, quite warm on upper back side, slow email, indication of a full or partially full charge dropping to no charge or dead when removed from charging source.
CAUSE: OS3 Bug prevents consistent charging, draining the battery even when plugged in to a computer via the USB or into an A/C adapter (although I've been able to intermittently charge on an A/C adapter). In push mode, the Exchange email client on the iPhone continually queries the Exchange Server, cycling the iPhone CPU and continually draining the battery at a high rate (can
WHAT I'VE BEEN TOLD BY APPLE:
1) Defective Hardware (though I'm on my third 3G in a week, so I don't think hardware is the problem . . . Apple will consider replacement with a new 3G if my third 3G has the same problem)
2) Corrupted App in iTunes - so I manually reloaded each app directly over wi-fi, one app at a time, this worked until I configured Exchange Email, at which time symptoms immediately appeared . . . so corrupted app unlikely.
3) Initial data transfer after email configuration . . . but symptoms continued long after this.
4) Wi-Fi - but turning wi-fi on or off had little effect, beyond normal.
5) Restore to New Phone - this works fine UNTIL Exchange Email is configured and activated. Thus, the time consuming practice of reload all apps, photos, music, etc. will be for naught, once exchange email is turned on with "push"
SOLUTION: Turning off "push" on your exchange email account
1) Go to Settings - Mail, Contacts, Calendars - Fetch New Data
2) Set Fetch Setting to 15 minutes to approximate the much more frequent "push" uploads and downloads. NOTE: Turning off \"push\" at this level will NOT turn off push on your exchange email account and the problem will not be resolved
3) Scroll down and select - Advanced -
4) Identify and select your Exchange Server account
5) Select - Fetch -
6) Leave settings
Phone should cool down in a few minutes and work normally. The problem can be replicated and resolved repeatedly merely by toggling "push" on and off in your exchange email configuration.
I was told that this is likely to be the "fix" until a patch is issued. No time frame was given for an actual fix that allows Exchange users to use push technology. Disappointing, since broader use of "push" technology beyond exchange was one of the big benefits of OS 3.0.
NOTE: THIS PROBLEM DOES NOT OCCUR ON ALL iPHONES WITH OS3 USING THE EXCHANGE CLIENT. I have second 3G phone, identically configured (including push to exchange email) that has no symptoms at all. Go figure.

Since two days ago, my battery indicator has been indicating 100% until the phone dies, which seems to be one of the symptoms you're describing.
However, I don't use Push emails; my email client is configured to poll an imap server and has been that way since I got my phone over 6 months ago. To be on the safe side, I turned off Push anyway, but I'm still having the problem. Definitely 3.0 related as I've never had this problem before.
Perhaps it's linked to an app? Personally I don't have a whole lot of them installed: Aurora Feint, fstream, twitterific, flixster, wikipanion, google earth, urbanspoon, STM Mobile, iDicto, Air Sharing, Facebook and Apple Remote. I've removed a few and will see how it goes.

Server 2008R2 mapping to shared folders fails users of Windows 8.1 but seems OK on Windos 8.0 and no problems for Windows 7

Having read what I could from the related questions, the answers still elude me. This issue apparently is specific to Windows 8.1.
First, a little background.
1: The server is not on a domain, The system runs Server 2008-R2 standard with all folders shared across a standard "Workgroup" type network. They would prefer to
leave this layout intact.
2: The shared folders are nothing but Data files. There are no active system folders or anything used in an "active" environment. They are mostly Word doc, excel
files, pdf, txt, etc. However, due to the requirements of the software that needs to access these files, they Must
reside on a mapped network drive letter. Nothing else works due to the way the SQL database program stores the reference points back to the data.
I have had some success using what amounts to a “simulated” mapping using WebDAV to access the server. But access speed is a lot slower ad file size is limited.
3: The system has been configured as-is for the past 3 years with Users all on Windows 7 x64 (mixed OS, some Home Premium, some Professional) and the only problems that come up are when
access is through an ISP that blocks port 445. This was the original reason for finding a WebDAV/Cloud method just for those Users since they were unable to Map drives to anything on the Office Servers from their Home Internet even when using a VPN.
When Windows 8.0 became the only version available, I added a few users whose new laptops came with 8.0 from the vendors. While there were a very few minor problems, for all practical
purposes, I was still able to provide access to the mapped folders.
As the Windows 8.1 roll-out progressed, some users were successfully upgraded while others are still stuck in Windows 8.0. The issues with this seem to be hardware related and vary
depending on the Make and model of the laptop. I have been assured that eventually all of these will be able to advance to 8.1. But this delay has given me an excellent mixed OS environment for testing.
On the users who have not yet purchased new equipment and who are still using Windows 7. There has been no change. Their drive mapping is stable and they can always connect as usual.
Those blocked from lack of port 445 or still blocked. Systems inside the Office and those with ISP's who allow port 445 can use all mapped drives as normal.
Users who had Windows 8.0 and who have not yet been able to upgrade to 8.1 also have been unaffected. Same results as Windows 7.
Users who got the Windows 8.1 upgrade as well as those that came factory loaded with Windows 8.1 seem to be a never-ending list of problems. The ones that came native with 8.1 are worst
of all. The list of error codes runs through everything that has to do with “communication with the server”. As far as I have seen, this appears to be the issue.
Whether they are in the office on a wired network connection or at home on a Wi-Fi connection, the issues have the same results but the actual error codes may vary slightly. All of
them refer back to an inability to communicate with the server.
Nothing on the server has changed in any way. Users with Windows 7 continue to have zero problems, Users with Windows 8.0 seem to be doing fine as well. Only those with Windows
8.1 are affected and their problems are dramatic with everything from a total loss of drive mapping to misdirected data when the maps are active.
I have tried to make the drives automatically remap on reboot. I have tried registry modifications. I have done everything I can think of to make a difference but the results are the same
for every system using 8.1. The mapped drive letters invariably disappear. Sometimes while the system is in use ( I think I have been able to trace this to times when the system enters Sleep or Hibernate) but always when the system reboots.
One detail that might point to somewhere is that the "time to connect" when mapping the drive is so long that I believe some of the original failures were due to not waiting for a
minimum of 3 or 4 minutes to give time for the Shares to show-up in order to map them. Once the mapping is successful, the file access speed seems normal. But invariably, the drive becomes "unmapped" repeatedly each day.
I know this was a long question but I have tried to provide every possible detail for anyone who has experienced events like this who may already have a solution. I would even be glad
to purchase a 3rd party application if that is what it takes to get this to work. My next planned effort is to try using Server 2013 but I am afraid that might open another can of worms for those who still use Windows 7.
I have also been told that this is in some way related to the push to "Cloud" support in Windows 8.1 OS but I do not see where this would come in. I can say that this was the
one place where things continued to work as before. People who had Windows 8.1 and who had to use the CLOUD copies of our data are still able to connect to it with no problems.
Any suggestions appreciated. Preferably those that would not need extensive changes to the basic network structure. This "workgroup" consists of less than 25 users and any
extreme measures would be hard to justify

Hi，
I sugget you try to ping server so that we can verify the connectivity.
Can windows 8.1 access Windows Server 2008R2?
Also,please check the event viewer to see if some error log appeared when the issue occurred.
Regards,
Kelvin Xu
TechNet Community Support

Serious and Sudden Problem with Z10 NEED HELP PLEASE

I have a z10, one of the first that came out in Toronto (if it makes a
difference), a couple of hours ago I came across a serious and sudden
problem.
I was able to swipe left and right between pages of apps, even drop down
from the top, but I cannot open anything, not even make a call or settings
options.
Any time I try to, for a split second it looks like its about to load
something then nothing. (image slides to the right quickly and goes back on
every attempt)
So I first did a reset, same problem, then I did a battery pull (about 15 minutes) and problem presisted.
I tried through USB to do a backup on blackberry manager and perhaps do a
re-install of everything, however when I was prompted for the password of
my device on my PC it kept telling me it was an incorrect password (I use
this blackberry on my computer 4-7 days a week, twice a day sometimes for a
year and I have never miss typed my password nor have i changed it)
After trying everything to make sure the first letter maybe was upper/lower
case, even my other possible phone password, nothing worked..
On the 5th failed attempt my phone prompted me to type 'blackberry', which
i did, then i typed my password on my phone which i type in about 15 times
a day becuase I set my phone to a 5 minute lock and still said it was incorrect.... I am no on 9/10 attempts and lost
for options.
Please if anyone can give me any suggestions, or even how to backup my phone
and whipe it now, or I have an earlier backup form 4 months ago that I
wouldnt mind going back to in worst case scenario.
Thank you for your help in advance,
Solved!
Go to Solution.

Sorry, no I haven't experienced that. It could be from an app you downloaded but that's just a guess. Wiping the device will tell us a lot. If the device still doesn't work you'll want to reload the OS using BB Link. if it still doesn't work after that then warranty support will be necessary through Rogers.
1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

XML DevCon 2001: Submit schema and stylesheet problems- win XML Spy

There are only a few days to submit schema and stylesheet problems for XML
DevCon 2001 in London. If the workshop instructors use your submission
during the conference, you win a copy of XML Spy.
<shamelessPlug>
XML DevCon 2001 has a content-rich technical program with a faculty that
includes Henry Thompson (W3C Fellow), Peter Chen (IEEE Fellow, ACM
Fellow),
Martin Bryan (DIFFUSE Project), and authors such as Bob DuCharme, Ian
Graham, Elliotte Rusty Harold, G. Ken Holman, Benoît Marchal, JP
Morgenthal,
and Simon St. Laurent. There are a variety of eBusiness sessions,
including
panel discussions and presentations about ebXML, Web Services, and UDDI.
The program includes presentations by Jonathan Borden, Ron Bourret, Lee
Buck, Alex Chaffee, Mark Colan, John Evdemon, Meike Klettke, Andy
Longshaw,
Ingo Macherius, Simon Nicholson, David Orchard, Sebastian Rahtz, Daniel
Rivers-Moore, Michael Rys, Krishna Sankar, Matt Sergeant, Richard Tobin,
Priscilla Walmsley, David RR Webber and other distinguished faculty.
</shamelessPlug>
http://www.xmldevcon2001.com/London/html/conference.php
For a free pass to exhibits and special events (keynotes, joint XML UK and
British Computer Society meeting, OASIS XPath/XSLT meeting, vendor
presentations):
http://www.xmldevcon2001.com/London/html/special_events.php
Public submissions (schemas and stylesheets)
Three members of the W3C Schema Working Group (Michael Rys, Henry
Thompson, Priscilla Walmsley) will teach a Schema Workshop. Submit
problem schemas to them by e-mail:
[email protected]
or
http://www.xmldevcon2001.com/London/html/session.php?code=W5
Sebastian Rahtz, Bob DuCharme, Benoît Marchal, and Ken Holman will
present the "Stylesheets and Transformations: Best Practices" workshop on
Thursday, February 22 in London. To submit a stylesheet or problem
description for their workshop:
[email protected]
or browse to:
http://www.xmldevcon2001.com/London/html/session.php?code=T17
========== Ken North ======================
See you at Javacon 2001 (New York, March 1)
www.javacon2001.com
XML DevCon 2001: London (February 21-23) New York (April 8-11)
www.xmldevcon2001.com
=======================================

Looks okay to me. But then I have no idea of what those "problems" are that you mentioned. Was there a particular reason you didn't tell us what they are?

Layout and style problem

HI
I am building a new dashboard using one of the templates given in the program. Two things that are bugging and giving problems are with the styling in the spreadsheet. I formatted targeted cells in the spread sheet to use certain colors and font alignment in the cell's , but when i update the spread sheet in the dashboard, it does pull over the right cells with all the macro's but doesnt pull over the right styling. The text color is some thing else and it doesnt want to use the text alignment in the cells. I have to use certain colors because of the branding of the company. Please help
Thanks

HI
The macros in my excel work sheet call information from my excel data sheet. These two sheets then give style and data information through to the dashboard for the spread sheets used to display some cell information. Must i change the targeted cells color through script or enforce the style with script ? Cause i used the standard excel cell properties to do the formatting and have never had any problems with it not styling the dashboard right in the past. Can it be that my macros on the cells cause the cell style information not to be given to the dashboard?
Thanks

Xml validation and transformation in a row: Possible?

Hi.
I'm working on a small tool that uses javax.xml.validation and javax.xml.transform (JDK 6) to perform validation and transformation of xml files in a row.
The problem is, the namespaces and reference to the xml schema required by the validator somehow prevent the transformation from extracting data from the xml file.
Here's the header I use in the xml file:
<tagWhatever
xmlns="http://www.myPlace.com"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="http://www.myPlace.com mySchema.xsd">To sum it up, with the namespace declaration within the xml I can validate but not transform, and without the declaration, I can transform but not validate.
Can anyone help me out witht this one?
Thanks
5thString

Hi.
I'm working on a small tool that uses javax.xml.validation and javax.xml.transform (JDK 6) to perform validation and transformation of xml files in a row.
The problem is, the namespaces and reference to the xml schema required by the validator somehow prevent the transformation from extracting data from the xml file.
Here's the header I use in the xml file:
<tagWhatever
xmlns="http://www.myPlace.com"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="http://www.myPlace.com mySchema.xsd">To sum it up, with the namespace declaration within the xml I can validate but not transform, and without the declaration, I can transform but not validate.
Can anyone help me out witht this one?
Thanks
5thString

Can we cleanse and transform data at flat file or external table level?

Hi,
I have some data that I want to cleanse and transform. I don't want to cleanse it after i populate the external table, I want to get done with it at flat file level or while populating the external table. Can we cleanse and transform data at flat file or external table level through Oracle or OWB 11.2? Is it possible to run a conditional load (i.e. having a where clause or if-else-then) for an external table? Can we call oracle functions for an external table at the time of creation?
Thanks in advance.
Regards,
Ann.

Hi Oleg,
Thanks a lot for the clarification. :)
So is there a way that I can clease the data within the text file through Oracle or OWB? I have datatype mismatches in the data and most of my data is getting rejected because of that. The way I can think of, for solving this problem, is to create the external table with all fields with datatype varchar and then cleansing the data. But it doesn't seem very effecient plus it will get very complicated because I have almost 80-90 fields.
Any help?
Thanks and regards,
Ann.

ODS and Transformations get inactive after i transport it in PD.

i have transported my ETL model in production , Now Everything what we have transported has come into production system but transformation and ODS in our ETL model get inactivated . Also while i want to display the transformation it give massege that " 'the infosource that we have created before the transformation in not active and can not be used . '
Our ETL model is like
Cube(now Active) --- tranformation(Now is in not active state) -- ODS(Now is in not active state) -- transformaion(Now is in not active state) -- infosource(Now in active state) -- transformation(Now in active state) -- PSA .
the part    ": tranformation -- ODS -- transformaion " gets inactivated after transportation also DTP which pull data from ODS to cube also get inactive .
Please suggest me to how i can activate these inactive object or i have to transport these object again to PD
Thanks .

Hi Bryan ,
        Yes data was their inside the ODS while transporting , Now i have successfully transported the request , nd now activating ODS transformation nd DTP . Actually i got a prog to activate transformation and DTP and want to share with all ... . i juz activate mt DTP and transformation though these prog .
Program for DTP ACTIVATION
*& Report ZDTP_ACTIVATE
*Coded by NBS BI team
*Date: 15-JAN-2010
*Function: For DTPs activation
REPORT ZDTP_ACTIVATE.
TYPES: BEGIN OF t_dtp,
dtp LIKE rsbkdtpstat-dtp,
objstat LIKE rsbkdtpstat-objstat,
src LIKE rsbkdtp-src,
tgt LIKE rsbkdtp-tgt,
END OF t_dtp.
TYPES: i_dtp TYPE STANDARD TABLE OF t_dtp.
DATA: lv_output(255) TYPE c,
lv_subrc TYPE sysubrc,
tab_dtp TYPE i_dtp,
r_dtp TYPE REF TO cl_rsbk_dtp.
SELECTION-SCREEN BEGIN OF BLOCK b1.
SELECTION-SCREEN SKIP 1.
PARAMETERS: p_id TYPE char35.
SELECTION-SCREEN END OF BLOCK b1.
START-OF-SELECTION.
FIELD-SYMBOLS: <fs_dtp> TYPE t_dtp.
REFRESH tab_dtp.
SELECT * FROM rsbkdtp AS a JOIN rsbkdtpstat
         AS b ON adtp = bdtp INTO
        CORRESPONDING FIELDS OF TABLE tab_dtp
         WHERE a~dtp = p_id AND
            a~objvers = 'A' AND
              b~objstat = 'INA'.
IF tab_dtp IS NOT INITIAL.
    LOOP AT tab_dtp ASSIGNING <fs_dtp>.
      CALL METHOD cl_rsbk_dtp=>factory
        EXPORTING
          i_dtp   = <fs_dtp>-dtp
        RECEIVING
          r_r_dtp = r_dtp.
      IF sy-subrc = 0.
        CALL METHOD r_dtp->activate
          EXPORTING
            i_objvers             = rs_c_objvers-modified
            i_force_activation    = rs_c_true
            i_show_check_protocol = rs_c_false
            i_with_cto            = rs_c_true
          IMPORTING
            e_subrc               = lv_subrc.
        IF lv_subrc = 0.
          CONCATENATE 'Activated DTP : ' <fs_dtp>-dtp ' : ' <fs_dtp>-src '->' <fs_dtp>-tgt INTO lv_output.
        ELSE.
          CONCATENATE 'DTP : ' <fs_dtp>-dtp ' : ' <fs_dtp>-src '->' <fs_dtp>-tgt ' Could Not be Activated' INTO lv_output.
        ENDIF.
      ENDIF.
      WRITE:/ lv_output.
    ENDLOOP.
ELSE.
    WRITE:/ 'DTP is not Inactive'.
ENDIF.
Program for TRANSFORMATION ACTIVATION
**& Report ZTRFN_ACTIVATE
*Coded by NBS BI team.
*Date: 15-Jan-2010
*Function: Activates in-active transformation only.
REPORT ZTRFN_ACTIVATE.
TYPES: t_tran TYPE rstran,
i_tran TYPE STANDARD TABLE OF t_tran.
DATA: r_tran_maintain TYPE REF TO cl_rstran_maintain,
lv_subrc TYPE sy-subrc,
lv_output(255) TYPE c,
tab_tran TYPE i_tran,
i_s_source TYPE rstran_s_tlogo,
i_s_target TYPE rstran_s_tlogo.
SELECTION-SCREEN BEGIN OF BLOCK b1.
SELECTION-SCREEN SKIP 1.
PARAMETERS: p_id TYPE char35.
SELECTION-SCREEN END OF BLOCK b1.
START-OF-SELECTION.
FIELD-SYMBOLS: <fs_trans> TYPE t_tran.
REFRESH tab_tran.
SELECT * FROM rstran
INTO TABLE tab_tran
WHERE tranid = p_id AND objvers = 'A' AND objstat = 'INA'.
SORT tab_tran.
IF tab_tran IS NOT INITIAL.
    LOOP AT tab_tran ASSIGNING <fs_trans>.
      TRY.
          CREATE OBJECT r_tran_maintain
            EXPORTING
              i_tranid       = <fs_trans>-tranid
              i_s_source     = i_s_source
              i_s_target     = i_s_target
              i_expert       = rs_c_false
              i_mode         = rsawc_c_tfc-display
              i_with_message = rs_c_true.
        CATCH cx_rstran_not_found .
        CATCH cx_rstran_input_invalid .
        CATCH cx_rstran_cancelled .
        CATCH cx_rstran_not_authorized .
        CATCH cx_rstran_display_only .
        CATCH cx_rstran_already_exist .
        CATCH cx_rstran_error_with_message .
      ENDTRY.
      CALL METHOD r_tran_maintain->check
        EXPORTING
          i_with_display = rs_c_true
        IMPORTING
          e_subrc        = lv_subrc.
      IF lv_subrc = 0.
        CONCATENATE 'Activated Transformation : ' <fs_trans>-tranid ' : ' <fs_trans>-sourcename '->' <fs_trans>-targetname INTO lv_output.
      ELSE.
        CONCATENATE 'Transformation : ' <fs_trans>-tranid ' : ' <fs_trans>-sourcename '->' <fs_trans>-targetname 'Could Not be Activated' INTO lv_output.
      ENDIF.
      IF lv_subrc = 0.
        TRY.
            CALL METHOD r_tran_maintain->execute
              EXPORTING
                i_wrkmode = cl_rstran_stat=>wrkmode_activate
              IMPORTING
                e_subrc   = lv_subrc.
          CATCH cx_rstran_cancelled .
          CATCH cx_rstran_error_with_message .
          CATCH cx_rstran_display_only .
        ENDTRY.
      ENDIF.
      WRITE:/ lv_output.
    ENDLOOP.
ELSE.
    WRITE:/ 'Transformation is not Inactive'.
ENDIF.

Java transform problem - resulting XML has wrong namespace on imported Node

I use Document.importNode(Node, String) to import a node from one document into another document. I want to preserve the namespace of the imported node. This works ok if the imported node specifies xmlns, even xmlns="". But if the imported node does not specify a namespace, I would expect the resulting serialized XML to have xmlns="". However, this is not the case. I use javax.xml.transform.Transformer when I serialize the XML. After the transform, the imported node has the namespace of the document it is imported into, which we do not want. So how do I get the imported node to serialize out with xmlns="", even if it's not specified in the source document? I am using javax.xml.transform.* and javax.xml.parsers.DocumentBuilder from Java 1.4.2.
Example of XML that node is imported into (imported node replaces PayloadPlaceHolder):
<?xml version="1.0" encoding="UTF-8"?>
<Envelope envelopeVersion="0.0.0" classificationLevel="Unclassified" xmlns="http://disa.gcss.mil/XMLGateway/Envelope">
<Header>
<UID>GM0000001</UID>
<DateTime>2006-12-05T16:11:50Z</DateTime>
</Header>
<Status reason="FAILED" lastTransactionID="9999999999" inReplyTo="ZZZ9999999999">
<LastMessageUID>ZZZ9999999999</LastMessageUID>
</Status>
<Payload>
<PayloadPlaceHolder>
</PayloadPlaceHolder>
</Payload>]
</Envelope>
Example of XML with null namespace, test_segment is imported node:
<?xml version="1.0" encoding="UTF-8"?>
<test_segment>
<name>test</name>
</test_segment>
Example of result XML with imported node (test_segment):
<?xml version="1.0" encoding="UTF-8"?>
<Envelope classificationLevel="Unclassified" envelopeVersion="0.0.0" xmlns="http://disa.gcss.mil/XMLGateway/Envelope">
<Header>
<UID>GM0000001</UID>
<DateTime>2006-12-05T16:11:50Z</DateTime>
</Header>
<Status inReplyTo="ZZZ9999999999" lastTransactionID="9999999999" reason="FAILED">
<LastMessageUID>ZZZ9999999999</LastMessageUID>
</Status>
<Payload>
<test_segment>
<name>test</name>
</test_segment>
</Payload>
</Envelope>
Here is the code to build the documents and transform the XML:
     Document document = null;
Document dataBlockDoc = null;
ByteArrayInputStream inStream = new ByteArrayInputStream
(StringUtils.getBytes(xml.toString()));
try {
DocumentBuilderFactory dbf = DocumentBuilderFactory.newInstance();
dbf.setNamespaceAware( true );
DocumentBuilder parser = dbf.newDocumentBuilder();
document =
parser.parse(
new InputSource(inStream ) );
if (dataBlock != null) {
inStream = new ByteArrayInputStream(StringUtils.getBytes(dataBlock));
dataBlockDoc = parser.parse(
new InputSource(inStream ) );
Element root = document.getDocumentElement();
Element payload = null;
NodeList children = root.getChildNodes();
//get Payload child from envelope document
for (int i = 0; i < children.getLength(); i++) {
if (children.item(i).getNodeName().equals("Payload")) {
payload = (Element)children.item(i);
break;
//get the PayloadPlaceHolder
Element payloadPlaceHolderElement = null;
children = payload.getChildNodes();
for (int i = 0; i < children.getLength(); i++) {
if (children.item(i).getNodeName().equals("PayloadPlaceHolder")) {
payloadPlaceHolderElement = (Element)children.item(i);
break;
Node newPayload = null;
if (dataBlockDoc != null) {
Element dataBlockElement = dataBlockDoc.getDocumentElement();
//make new Payload element to replace old (empty) Payload
newPayload = document.importNode((Node) dataBlockElement, true);
payload.replaceChild(newPayload, payloadPlaceHolderElement);
else
payload.removeChild(payloadPlaceHolderElement);
TransformerFactory tf = TransformerFactory.newInstance();
Transformer nullTransform = tf.newTransformer();
ByteArrayOutputStream oStream = new ByteArrayOutputStream();
nullTransform.transform(                    new DOMSource( document ),
     new StreamResult( oStream ) );
xml = new StringBuffer(oStream.toString());
Thanks in advance.

It appears that the problem is that the DOM serializer implementation in JDK 1.4 is not properly handling namespaces. Does anyone know of a workaround or alternate serializers we could use to serialize a DOM tree? I also need it to work with XSLT.
Thanks.

I phone 5 problems; Siri, music, and wifi problems

On my iphone 5, music will randomly start playing, and also Siri will randomly turn on without pushing any buttons. Another problem I'm having is, my phone won't say connected to my home wifi. Anybody else having these problems, is it just a iOS7.4 problem that they have to update?and do you know how to fix it?

Make sure you have the Latest Version of iTunes (v11) Installed on your computer
iTunes free download from www.itunes.com/download
Then...
Connect to iTunes on the computer you usually Sync with and Restore
http://support.apple.com/kb/HT1414

Push-Pull Inverter and Transformer Problems

Similar Messages

Maybe you are looking for