Put same ip on 2 interfaces (router)

Hello. I would like to configure my C2911 router with 2 C2960 switch. And is it possible to put same ip on 2 interfaces of C2911? One for active and another one or standby. Topology was attached. Is it possible?
thankyou

Yes you can!
interface FastEthernet0/0
 ip address 10.10.10.1 255.255.255.0
 speed 100
 full-duplex
interface FastEthernet0/1
 backup interface FastEthernet0/0
 ip address 10.10.10.1 255.255.255.0
 speed 100
 full-duplex
Cheers!

Similar Messages

  • Interface Routing

    Im using 2 Presonus Firestudio Intefaces with Logic Express and want to route 8 outs of each interface to my mixing console for a total of at least 16 outs.
    My problem is, i cant seem to route the tracks within Logic as single outs. Its either 1-2, 3-4, 5-6, etc.. I would like to route them as 1, 2, 3, etc..
    Can this be done within Logic and if so, how?

    Found it:
    same-security-traffic
    To permit communication between interfaces with equal security levels, or to allow traffic to enter and exit the same interface, use the same-security-traffic command in global configuration mode. To disable the same-security traffic, use the no form of this command.
    same-security-traffic permit {inter-interface | intra-interface}
    no same-security-traffic permit {inter-interface | intra-interface}
    Syntax Description
    inter-interface
    Permits communication between different interfaces that have the same security level.
    intra-interface
    Permits communication in and out of the same interface.
    Defaults
    This command is disabled by default.
    Command Modes
    The following table shows the modes in which you can enter the command:
    Command Mode Firewall Mode Security Context
    Routed Transparent Single Multiple
    Context System
    Global configuration
    •
    •
    •
    •
    Command History
    Release Modification
    7.0(1)
    This command was introduced.
    7.2(1)
    The intra-interface keyword now allows all traffic to enter and exit the same interface, and not just IPSec traffic

  • Should airport express be configured with the same network as my existing router

    Should airport express be configured with the same network name as my Verizon router.

    Carolyn1962 wrote:
    I am new to apple,used to windows.Apple store advised airport express in order to boost my DSL router.In order for it to be most effective should it be under the same settings.Still learning
    A router signal can not be boosted as all routers put out the maximum allowed by law.  However, proper placement of a secondary router will enable it to "repeat" or extend the signal.
    An Airport can "extend" the WiFi created by another Airport.  It can not extend a non-Apple WiFi.  You need TWO Airport units, one to function as the main radio and the other to function as an extender.  I used two Express units.
    Configuration is simple if you start from a factory default condition.  Connect the main Airport to AC power and finally to the Internet modem (or modem/router).  Open Airport Utility on your Mac or other computer and accept all of the recommendations.  After confirming that it works, insert your desired administrative and WiFi passwords.
    Then connect the extender to AC power.  As before, open Airport Utility on your Mac or other computer and accept all of the recommendations.  No need to add password info.
    Do not expect the Airport to respond instantly to the configuration commands.  BE PATIENT!

  • Communication between thread in the same process using file interface.

    Hi,
    I am developing  driver and i need to communicate between two thread.
    >can anyone guide me on implementing communication between two thread in the same process using File Interface. First thread will be driver and second will be application.I need to send IOCTL like commands using File interface ie is WriteFile(),ReadFile()
    from Host process to driver through file-interface(which run's in driver context).Host process should not be blocked for the duration of the driver to process the command.
    >File-interface will run in driver context and it will be responsible to receive command from application and pass it to the driver.
    what are the complexity introduced?
    >Can anyone also give me the link/reference to get more information on this topic?
    >How to replace IOCTL command's for instance baud _rate change command with a file interface for example with IRP.

    Here  is the detailed query:
    Hardware Abstraction Layer will interact with Driver(Both will be running in complete different process) .there is a IOCTL for command and  File interface for read and write.
    My requirement is:
    Both should run in the same process so HAL will run as one thread and driver as another thread in the same process .I don't want HAL to wait for completion of request and also i don't want driver to be blocked .
    We are planning to use a File Interface for communication between Hardware abstraction layer and Driver
    HAL will send the command or read/write operation to a file interface and driver will get the command or read/write request from the File interface
    There is a flexibility to change Hardware Abstraction layer and also the Driver
    Is it possible to use IOCTL between two thread under same process? if not what other options do we have.
    Can we use File interface to  send command (like IOCTL) between two thread?

  • Putting Same condition 2 times in a query

    Hi,
    Below query i have put same condtion 2 times, which incresed the performance from hanging to 5 secs.
    Pls tell mew will this condition produce different results?
    SELECT
    REP_V_CAMPAIGN.NAME,
    ALIAS_ACCOUNT_MANAGER.NAME,
    ALAIS_CONTACT_ACCOUNT.CHANNEL,
    ALIAS_ACCOUNT_MANAGER_WRKGROUP.WORKGROUP
    FROM
    REP_V_CAMPAIGN,
    REP_V_EMPLOYEE ALIAS_ACCOUNT_MANAGER,
    REP_V_ACCOUNT ALAIS_CONTACT_ACCOUNT,
    REP_V_WORKGROUP ALIAS_ACCOUNT_MANAGER_WRKGROUP,
    REP_V_CAMPAIGN_CONTACT,
    REP_V_CAMPAIGN_CONTACT_MAPPING
    WHERE
    ( REP_V_CAMPAIGN.CAMPAIGN_ID=REP_V_CAMPAIGN_CONTACT_MAPPING.CAMPAIGN_ID )
    AND ( REP_V_CAMPAIGN.CAMPAIGN_ID=REP_V_CAMPAIGN_CONTACT_MAPPING.CAMPAIGN_ID ) AND ( REP_V_CAMPAIGN_CONTACT.CONTACT_ID=REP_V_CAMPAIGN_CONTACT_MAPPING.CONTACT_ID )
    AND ( ALAIS_CONTACT_ACCOUNT.ACCOUNT_ID=REP_V_CAMPAIGN_CONTACT.ACCOUNT_ID )
    AND ( ALAIS_CONTACT_ACCOUNT.MANAGER_ID=ALIAS_ACCOUNT_MANAGER.EMPLOYEE_ID )
    AND ( ALIAS_ACCOUNT_MANAGER.WORKGROUP_ID=ALIAS_ACCOUNT_MANAGER_WRKGROUP.WORKGROUP_ID )
    AND (
    REP_V_CAMPAIGN.NAME IN ('BD-GVA-2005-04-Global Phone Day')
    Thanks,
    Kumar.
    Message was edited by:
    user548258

    Duplicate post:
    http://forums.oracle.com/forums/thread.jspa?threadID=476726&tstart=0

  • HT2486 How can you put same contact in a Group multiple times so that you can print the same mailing label multiple times?

    How can you put same contact in a Group multiple times so that you can print the same mailing label multiple times?

    Hello,
    Avery...
    https://discussions.apple.com/thread/2588943?start=0&tstart=0
    Or...
    http://www.belightsoft.com/products/labelsaddresses/overview.php

  • Is it same IOS version for Switch & Router?

    Hi,
    Is it same IOS version for Switch & Router?
    Regards,
    Samuel

    Sam,
    The Latest Version depends upon the Switching platform.
    For example:
    On 2900XL Platform - 12.0(5)WC15
    On 2950 - 12.1(22)EA8
    On 3500XL Platform - 12.0(5)WC15
    On 3550 - 12.2(25)SEE2
    It would be better if you specify the switch platform that you have questions about, so we could point you in the right direction.
    I hope it helps.
    Regards,
    Arul

  • How do you create a folder to put same subject emails in?

    How do you create a folder to put same subject emails in?

    Hope this helps.
    http://support.apple.com/kb/PH14946

  • [Solved] Default interface routing issues

    I have two network interfaces connected to my newly installed ArchLinux server,  one LAN and one WAN connection.  The trouble is that all traffic that is trying to connect to the wan interface gets no response, while the LAN connection work without any issue.
    I am using udev to change my interfaces to lan0 and wan0, and i use netcfg to load the diffrent profiles.
    Lan0 uses a static local ip 192.168.0.118  with 192.168.0.2 as gateway
    Wan0 uses dhcp  with dynamic ip from my ISP.
    When i manually bring down my lan0 interface all my traffic goes through wan0 correctly, and it even responds to external calls.
    So i belive the issue lies somewhere in the local routing?
    I am trying to post all config files needed directly.
    /etc/rc.conf
    # /etc/rc.conf - Main Configuration for Arch Linux
    # LOCALIZATION
    # LOCALE: available languages can be listed with the 'locale -a' command
    # LANG in /etc/locale.conf takes precedence
    # DAEMON_LOCALE: If set to 'yes', use $LOCALE as the locale during daemon
    # startup and during the boot process. If set to 'no', the C locale is used.
    # HARDWARECLOCK: set to "", "UTC" or "localtime", any other value will result
    # in the hardware clock being left untouched (useful for virtualization)
    # Note: Using "localtime" is discouraged, using "" makes hwclock fall back
    # to the value in /var/lib/hwclock/adjfile
    # TIMEZONE: timezones are found in /usr/share/zoneinfo
    # Note: if unset, the value in /etc/localtime is used unchanged
    # KEYMAP: keymaps are found in /usr/share/kbd/keymaps
    # CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
    # CONSOLEMAP: found in /usr/share/kbd/consoletrans
    # USECOLOR: use ANSI color sequences in startup messages
    LOCALE="sv_SE.UTF-8"
    DAEMON_LOCALE="no"
    HARDWARECLOCK="UTC"
    TIMEZONE="Europe/Stockholm"
    KEYMAP="sv-latin1"
    CONSOLEFONT=
    CONSOLEMAP=
    USECOLOR="yes"
    # HARDWARE
    # MODULES: Modules to load at boot-up. Blacklisting is no longer supported.
    # Replace every !module by an entry as on the following line in a file in
    # /etc/modprobe.d:
    # blacklist module
    # See "man modprobe.conf" for details.
    MODULES=()
    # Udev settle timeout (default to 30)
    UDEV_TIMEOUT=30
    # Scan for FakeRAID (dmraid) Volumes at startup
    USEDMRAID="no"
    # Scan for BTRFS volumes at startup
    USEBTRFS="no"
    # Scan for LVM volume groups at startup, required if you use LVM
    USELVM="yes"
    # NETWORKING
    # HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
    HOSTNAME="weed-devil"
    # Use 'ip addr' or 'ls /sys/class/net/' to see all available interfaces.
    # Wired network setup
    # - interface: name of device (required)
    # - address: IP address (leave blank for DHCP)
    # - netmask: subnet mask (ignored for DHCP) (optional, defaults to 255.255.255.0)
    # - broadcast: broadcast address (ignored for DHCP) (optional)
    # - gateway: default route (ignored for DHCP)
    # Static IP example
    # interface=eth0
    # address=192.168.0.2
    # netmask=255.255.255.0
    # broadcast=192.168.0.255
    # gateway=192.168.0.1
    # DHCP example
    # interface=eth0
    # address=
    # netmask=
    # gateway=
    #interface=eth0
    #address=
    #netmask=
    #broadcast=
    #gateway=
    # Setting this to "yes" will skip network shutdown.
    # This is required if your root device is on NFS.
    NETWORK_PERSIST="no"
    # Enable these netcfg profiles at boot-up. These are useful if you happen to
    # need more advanced network features than the simple network service
    # supports, such as multiple network configurations (ie, laptop users)
    # - set to 'menu' to present a menu during boot-up (dialog package required)
    # - prefix an entry with a ! to disable it
    # Network profiles are found in /etc/network.d
    # This requires the netcfg package
    NETWORKS=(sluggy local)
    # DAEMONS
    # Daemons to start at boot-up (in this order)
    # - prefix a daemon with a ! to disable it
    # - prefix a daemon with a @ to start it up in the background
    # If you are sure nothing else touches your hardware clock (such as ntpd or
    # a dual-boot), you might want to enable 'hwclock'. Note that this will only
    # make a difference if the hwclock program has been calibrated correctly.
    # If you use a network filesystem you should enable 'netfs'.
    DAEMONS=(syslog-ng !ufw !network net-profiles @alsa crond dbus sshd lircd sensors mysqld @ddclient @hddtemp httpd samba stunnel sabnzbd sickbeard)
    /etc/network.d/sluggy
    CONNECTION='ethernet'
    DESCRIPTION='A basic dhcp ethernet connection using iproute'
    INTERFACE='wan0'
    IP='dhcp'
    ## for DHCPv6
    #IP6='dhcp'
    ## for IPv6 autoconfiguration
    #IP6='stateless'
    /etc/network.d/local
    CONNECTION='ethernet'
    DESCRIPTION='A basic static ethernet connection using iproute'
    INTERFACE='lan0'
    IP='static'
    ADDR='192.168.0.118'
    GATEWAY='192.168.0.2'
    output of route -nl
    Destination Gateway Genmask Flags Metric Ref Use Iface
    0.0.0.0 192.168.0.2 0.0.0.0 UG 0 0 0 lan0
    0.0.0.0 85.24.137.1 0.0.0.0 UG 203 0 0 wan0
    85.24.137.0 0.0.0.0 255.255.255.0 U 203 0 0 wan0
    192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 lan0
    I have had this server running Ubuntu for the past 2 years with the same setup on the NIC's and there everything worked, so I guess i have become a little lazy.
    *EDIT* Updated my post with "code" block instead of quote
    Last edited by kurri (2011-11-01 22:07:14)

    kurri, please edit your post.
    When pasting code, please use [ code ] tags https://bbs.archlinux.org/help.php#bbcode
    like this
    It makes the code more readable and more convenient to scroll through.

  • Murder on the Airport Express (AE 1st Gen cannot find Wireless while plugged in in the same room as the modem, router and Time Capsule

    First, the reason for my compounded frustration:
    I wrote a lengthy, comprehensive post on this late last night.  I submitted it and received a notice at this URL:
    https://discussions.apple.com/___sbsstatic___/maintenance.html?start=0&tstart=0
    It gave a message:  "A yellow sticky bearaing the words, "We'll be back soon."  and a typed message reading, "We are busy updating Apple Support Communities for you and will be back shortly."  Needless to say, it never came back.  This morning as I began trying to reconstruct the very detailed post I wrote last night, the Communities system offered me an opportunity to restore the post from last night.  Sadly, it contained only a portion of the first line.
    I'm going to try it again.  The problem inherent in putting it all in words last night, is that I no longer remember the exact wording of the error messages.
    I've never gotten this Airport Express (1st gen, purchased mid 2010) to work.  I thought it was working, but working poorly.  A green light on the device is, apparently, NOT an indication of connection to the wireless.  It wasn't workingl.
    Description of devices which use the network:
    I have a Broadband network with a modem. 
    It is connecteed to my 2T Timecapsule (purchased mid 2010). 
    Connected to that is a 24 port Cisco Router. 
    Not connecting to that, though showing a solid green light, is my Airport Express (1st Generation, purchased mid 2010)
    Connected to the router are many ethernet cables giving hard-wired access to:
    Printers (HP 8600 Pro purchased 2012))
    MacBook Pro (purchased mid 2010) and
    IMAC (purchased mid 2010).
    3 Apple TV devices (1st generation purchased early 2011)
    1 Apple TV device (2nd generataion purchased August 2012)
    Connecting to the Wireless Network are IOS devices (current IOS versions on all)
    iPad 2nd generation (purchased the day it was available) 
    iPad 3rd generation (purchased the day it was available)
    iPod (mid 2010)
    iPhones (4S)
    Description of Layout of Network/House
    My home is approximately 70 feet by 25 feet. 
    All Networking hardware is at one end of the house, the south side.
    Airport Express (1st Gen, 2010) has been placed in the middle of the house to boost the wireless access at the north end of the house.
    Ethernet cables are installed under flooring with cable ends extending up through flooring, and are availble to all devices with Ethernet ports..
    Description of Problem
    Investigation of the wireless access dysfunction with the iPad (2nd generation, mid 2010)  revealed no connection to the Wireless Network, in spite of glowing green light on Airport Express and Airport Utility screen.
    Description of actions taken to correct the problem
    Loaded Airport Utility on MacBook Pro.
    Airport Express shows green light on screen.
    Double clicked on Airport Express Icon
    Message that Airport Express was unable to extend the network
    Message changes suddenly to something about not finding the Airport Express
    Airport Utility searches Airport Express, attempting to read its settings
    Message appears:  Device not found.  Airiport Express was previously part of the network, and offers to let me "forget" the base station.
    I exit the error message.
    A yellow triangle bearing an exclamation point sits to the left of the Airport Express' Description
    Airport Express shows green light (as always)
    Clicking the link, "Other AirPort Base Stations" indicates no base stations can be found.
    Moved Airport Express to the room at the south end of the house containing all network devices
    Plugged it in with clear, completely unobstructed view of Time Capsule.
    Light on Airport Express flashes yellow and then turns solid green (like always)
    Bring Mac into the room at the south end of the house containing all network devices and the Airport Express with the green light
    Close Airport Utility on Mac
    Reboot Mac
    Open Airport Utility on Mac
    Airport Express still shows as it did in 1.1.7. above.
    Attempts to check Airport Express' access to Wireless network:
    Unplugged Airport Express HEY!  THE GREEN LIGHT WENT OUT!!!  ;0)
    Disconnected all Ethernet cables.
    Tested ALL devices for Wireless access.
    All devices access the Wireless network extremely well (dot and three curved bars) EXCEPT
    IOS Devices tested at the north end of the house. These devices show a blank where the wireless bars should be, and intermittently show a dot.
    Followed instructions contained in a similar discussion about Airport Express not functioning:
    Unplugged all Networking Hardware
    Powered off all Equipment which access the Internet in any possible way.
    Powered up all Networking Hardware, one at a time, in the order described in that discussion.
    Powered up all Equipment which access the internet, one at a time.
    Tested ethernet cablingAll equipment functioning.
    Tested Wireless access:
    Removed all ethernet cabling
    All devices, including IOS devices, access the Wireless Network perfectly EXCEPT any placed in the north end of the house.  Those perform exactly as they did in step 3.3.2.
    Connected all ethernet cabling.
    Plugged Airport Express into socket in the Network Hardware room at the south end of the house.  I get exactlyt the same results as before.  The lovely green light glows on the Airport Express.  Airport Utility reports Airport Express cannot find the Wireless network and also says there are no base stations connected to the internet.
    Still in Network Hardware room, I attempt to find other base stations by cabling the Airport Express to the MacBook Pro
    Airport Utility shows Airport Express with a green light
    I double click the Airport Express Icon
    Box says connection is average and status is (green light) Extended Network.
    I click Edit
    I go through each tab.  I note that in the Wireless tab, the Network Mode is as I had set it, "Extend a wireless network".
    Under the Network tab I note that "Enable Access Control" is as it should be, NOT selected. 
    Under the AirPlay tab, I note that "Enable airPlay" is selected.
    I click cancel and leave the Edit screens.
    Curious to know if Airport Express can find the Wireless network now that the device claims to be functioning as an extended wireless network, I disconnect the ethernet cable from the Airport Express.
    I watch the Airport Utility screen closely.  Nothing is happening.
    With bated breath, I double click on the Airport Express icon.
    The popup box shows "extended wireless network"
    I click on edit and we start the whole mess over again.  (See 1.1-9. above)
    Curious to know if cabling the Airport Express to the iMac (almost to middle of house) will offer hope and prosperity to IOS devices at north end, I unplug the Airport Express and carry its now-exhausted little body to the iMac, ethernet cable in hand.
    As I unplug the iMac from its ethernet access, I'm informed by Cranky Boy that no way is he going to accept that as a reasonable solution to his problem.  He will not live wireless while even one ethernet cable is poking up through a floorboard.
    Cranky Boy is reassured when informed that, though the Airport Utility shows the Airport Express connected, merely double clicking on the icon produces the same result as laboriously described in 1.1-9. above.
    After quieting Cranky Boy by reconnecting the iMac to the Ethernet, I return the Airport Express to the Network Hardware room.
    Again, curious to know ...  I reconnect the Airport Express to the MacBook Pro. I want to know if it will exrtend the Wireless network from its position one foot from the Wireless Network.
    I close and reopen Airport Utility (as I always do, but forgot to write)
    I click on the Airport Express icon (which bears a little green light like the other big boys).
    BUT THIS TIME, when I click on the Airport Express icon, the pop-up box says my connection is Excellent, the green light status shows, "Extended Network" and clicking on "Extended Network" produces the same old `Airport Express was unable to extend the Wireless Connection. 
    I click on the Edit option. 
    I buzz through all the tabs.  I cancel instead of update, leaving everything as it was (as I did the first time)
    I decide to go back into edit and select "Internet Options" under the "Internet" tab.
    Since I have no idea whatsoever as to what IPV6 is and what it governs, I decide to configure IPV6 to Automatically Connect and then, with a whole new set of opportunities, I leave IPV6 Mode set to "Tunnel" and then I learn that I will get to see what happens when  "Enable IPV6 Connection Sharing" is enabled.
    I check the other tabs to see if anything has changed in their menus
    Jesus Saves and so did I. 
    Apple updates and so did I.
    I am warned that my device and its network services will be temporarily unavailable if I continue. 
    It seems unaware that I am laughing uncontrollably at the suggestion that my device and its services will be TEMPORARILY AVAILABLE.  What?  An improvement in performance is warned?
    Life continues and so do I.
    I breathe deeply to decrease my adrenaline.
    Airport Utility flashes a red warning next to the Airport Express Icon and then quickly rethinks the matter and decides to show it as connected.
    I click on the Airport Express Icon.  This time my connection is only "good".
    I click on Extended Network. With a new-found consistency it informs me that my device is unable to extend the Wireless network and it chats with me about using the same Wireless password for my device that is used for the Wireless network access.  I did.  It is.
    I change my settings back to the way they once were, I save like Jesus and Update like Apple
    I decide to go back into Edit and modify the settings under the Wireless tab, changing from "Extend Wireless Network" to "Join Wireless Network".
    I save.
    I click on the Airport Express Icon.  My connection has degraded further to "Average"
    I click on edit just to see what will happen, but no further information is forthcoming.  Settings are as I left them.
    I wonder if the Airport Express would extend itself now that it has joined the Wireless Network.
    I click the Airport Express Icon.
    I click Edit
    I change the Network Mode from "Join a Wireless Network" to Extend a Wireless Network. Unfortunately, there was no option for "don't forget where the Wireless Network is!"
    I am still "unable to extend the Wireless network"
    I disconnect the Airport Express from my MacBook Pro.
    After closing and opening Airport Utility, I sit and stare at the Airport Express Icon.
    It has no light or error messages
    It has a yellow triangle with exclamation point
    It has no light or error message
    It has a yellow triangle with exclamation point
    I finally decide to see what THIS error messages says.  It says Device Not Found.  Patti Harada's AirPort Express was previously part of your network.  Check that it is still in range of your network and is plugged into a power outlet.  Click Forget to remove this base station from this network."
    I click "Forget".  Airport Utility has forgotten the Airport Express ever existed.  It has also forgotten how to find it again.
    I, however, am unable to forget how much I shelled out for this POS and fear I will never recover from working this intensely and tediously on documenting something so hideously inconsistent in its test results.
    I wonder if I should recable the Airport Express to my MacBook Pro
    I decide I've had about enough.
    I document this ad nauseum in the hopes that someone can read it THOROUGHLY and offer me a solution to my problem.  What is my problem?  I am so busy fighting off Alligators that I forgot I only came in to drain the swamp!  Ah, but I remember now:  Cranky Boy can't watch Netflix on his iPad (2nd generation) in the north end of the house.
    Any solution that works will do.  I'll buy another piece of whatever kind of equipment you think best.

    Well, aren't you all that and a bag of chips!!!!
    Oh what a relief!  What a RELIEF!  
    That just cleaned up my life.  And Cranky Boy is actually smiling!!!
    Houston, we've got dots AND BARS!!!
    P.S.  All my firware and software are always current.  If I spent as much time looking for a reset button as I spend checking for software updates, I mighta not needed to work at this!!!!
    P.P.S.  Airport Utility shows Cranky Boy's iPad as the Airport Express' Wireless Client!!!   Who knew?
    Thank you so much, m'Lord.  I am in your debt.  What would you have me do?
    Patti in Tucson AZ

  • How to run Wired WRTG54G2 V1 in same subnet as my broadband router?

    Hi,
    I have a linksys broadband router E2000 and a cable running from it to another location where I have a linksys WRTG2 V1.
    I would like the WRTG2 to be running in the same subnet as the E2000, but I seem not be able to get this done.
    Appreciate any assitance. Is what I'm trying to do (briding I guess?) supported?
    regards
    Osama Salah

    So what you want to do is have these two routers in the same network, right? The WRT54G2 does not have a bridge mode option but this type of setup can easily be done. You simply have to cascade the routers LAN to LAN. For more details, check out this article: Cascading (Connecting) a Linksys router to another router.

  • How to put same target in one RDA daemon twice

    Hi
    Anyone have experience putting the same DSO target in one RDA daemon twice?
    I have a requirement to update one target from two sources in RDA. It seems that one of it always end in error.
    Thanks and regards
    Kwong Tat

    Hi Lev,
    Do the below steps:-
    first insert a table ,and create context according to ur need.
    now
    1.right click the table and then u get Insert Grouped Column .
    2.this will show u two options
    a)TableColumn
    b)TableColumn Group
    3)select table column group
    4)now right click on column group which generated in step 3 and Select Insert Column according to ur need(means how much columns u need)
    5)now in this new column right click and get Insert cell editor and choose whatever u want.
    means:-
    Right click on the table-->Select Insert Grouped Column -> Table Group Column
    Right click on the Table Group Column Created-->Select Insert Column-> Table Column..
    Repeat the above step.
    Right Click on the Table column->Insert Table Cell Editor.
    Hope this may help you...
    Deepak!!!
    Edited by: Deepak Arora on May 21, 2010 6:13 AM

  • Can not enter interface router.

    Cisco modem with Sitecom router and MacBook pro laptop and HP laptop
    IP router 192.168.0.1
    Can not enter interface and change SSID, code, etc. with the Apple mac.
    It works with the HP laptop.
    I just want the MAc to do that.
    What is there to be changed.

    Launch the Terminal application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, press the key combination shift-command-U. The application is in the folder that opens.
    ☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Terminal in the page that opens.
    Drag or copy – do not type – the following line into the Terminal window:
    curl -I http://192.168.0.1
    Press return. Post any lines of output that appear below what you entered. If there's no output within ten seconds, consider that a failure. You can then quit Terminal.

  • Logical ethernet interface routing

    Is there a way to configure a default route to a logical ethernet interface, another one that isn't of the physical unit? I.e., to have different default routes to hme0 and hme0:1?

    Hi radhika,
    Logical routing determines the logical receiver(s) for a given logical sender.
    Logical routing comprises the following two steps:
    Receiver determination during which you assign a receiver system to the sender interface of a sender.
    Interface determination during which you specify a receiver interface in the receiver system.
    Technical Routing is a Processing step of the Integration Engine that determines physical addresses of logical receivers.
    The physical address (end point) of the required receiver is retrieved from the Integration Directory.
    Both can be monitored in IE(ABAP) - SXMB_MONI.
    Thanks,
    Shweta

  • Put same toolbar button in two place

    Hi,
    Is there a way to put a same toolbar button in two or more places?
    Before version 4, I am able to put the 'Open a new tab' button in front of the bookmarks toolbar and still have the new tab button next to the last opened tab. But since the version 4 update, I notice the 'Open a new tab button' will only appear in one of these places.

    Hi,
    You can change the .skn file with notepad, but I'm not sure what will be retained in the output.
    For all skin related questions, check Rick Stone's Skinny on Skins: http://www.robowizard.com/RoboWizard/NewProject.htm#Downloads/Skinny_on_Skins.htm
    I don't know whether your questions are answered in skinny on skins, so post back if you don't find the solution in there.
    Greet,
    Willam

Maybe you are looking for