Putting PVDMs in NM-2V / VIC-2FXO / VIC-2FXS into DSP farm
I have a Cisco 2650XM router with an NM-2V module with one VIC-2FXO and one VIC-2FXS card in it. I'm very new to Cisco voice stuff and want to get started with it. I'm trying to pool the PVDMs on this router into a DSP farm so that they can be used in CME 4.1 with call conferencing / transcoding / VoIP calls between Cisco IP Communicator and Cisco VoIP physical phones but I'm having issues doing so. I believe I'm supposed to create a DSP farm by going into "voice-card X" mode and assigning them to the DSP farm?
I know that there are PVDMs present because they are listed when I do a "show voice dsp detail." I'm not sure if the PVDMs are present in the NM-2V module or actually on the VICs. Can someone offer advice?
Yeah, the only cards / modules that I have in the router are the NM-2V, VIC-2FXO, and VIC-2FXS. Here is the "show diag" output as well as some other ones that may be useful.
Press RETURN to get started!
*Mar 1 00:00:05.949: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
*Mar 1 00:00:25.281: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar 1 00:00:25.970: %SYS-6-CLOCKUPDATE: System clock has been updated from 00:00:25 UTC Fri Mar 1 2002 to 17:00:25 AZT Thu Feb 28 2002, configured from console by console.
*Mar 1 00:00:26.439: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
*Mar 1 00:00:27.873: %SYS-5-CONFIG_I: Configured from memory by console
*Jan 4 02:05:04.149: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.4(15)T14, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 17-Aug-10 05:40 by prod_rel_team
*Jan 4 02:05:04.153: %SNMP-5-COLDSTART: SNMP agent on host KINASE is undergoing a cold start
*Jan 4 02:05:04.322: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Jan 4 02:05:04.322: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Jan 4 02:05:05.435: %LINK-3-UPDOWN: Interface Foreign Exchange Office 1/0/0, changed state to up
*Jan 4 02:05:05.435: %LINK-3-UPDOWN: Interface Foreign Exchange Office 1/0/1, changed state to up
*Jan 4 02:05:05.439: %LINK-3-UPDOWN: Interface Foreign Exchange Office 1/1/0, changed state to up
*Jan 4 02:05:05.439: %LINK-3-UPDOWN: Interface Foreign Exchange Office 1/1/1, changed state to up
CNF-FILES: Clock is not set or synchronized, retaining old versionStamps
CNF files update complete (post init)
KINASE>en
KINASE#show diag
Slot 0:
C2650XM 1FE Mainboard Port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 3.0
PCB Serial Number FFFF
Part Number : 73-7755-04
RMA History : 00
RMA Number : 0-0-0-0
Board Revision : A0
Deviation Number : 0-0
Product (FRU) Number : C2650XM-1FE
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 03 6E 41 03 00 C1 0B FF FF FF 46 46 46
0x10: 46 FF FF FF FF 82 49 1E 4B 04 04 00 81 00 00 00
0x20: 00 42 41 30 80 00 00 00 00 FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Slot 1:
4 PORT Voice PM for C2600 Port adapter
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 1.1 Board revision H0
Serial number 26333860 Part number 800-02491-02
FRU Part Number NM-2V=
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x00: 01 65 01 01 01 91 D2 A4 50 09 BB 02 00 00 00 00
0x10: 88 00 00 00 01 06 27 17 FF FF FF FF FF FF FF FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF
VIC Slot 0:
FXO Voice daughter card (2 port)
Hardware revision 1.1 Board revision J0
Serial number 21522658 Part number 800-02495-01
Test history 0x0 RMA number 00-00-00
Connector type Wan Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 0D 01 01 01 48 68 E2 50 09 BF 01 00 00 00 00
0x30: 98 00 00 00 00 07 22 01 FF FF FF FF FF FF FF FF
VIC Slot 1:
FXO Voice daughter card (2 port)
Hardware revision 1.1 Board revision J0
Serial number 22783161 Part number 800-02495-01
Test history 0x0 RMA number 00-00-00
Connector type Wan Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 0D 01 01 01 5B A4 B9 50 09 BF 01 00 00 00 00
0x30: 98 00 00 00 00 11 16 01 FF FF FF FF FF FF FF FF
KINASE#sh voice dsp detail
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABORT PACK COUNT
==== === == ======== ========== ===== ======= === == ========= == ===== ============
C542 001 01 None 9.4.7 IDLE idle 0 0 1/0/0 NA 0 602/623
C542 002 01 None 9.4.7 IDLE idle 0 0 1/0/1 NA 0 593/590
C542 003 01 None 9.4.7 IDLE idle 0 0 1/1/0 NA 0 601/622
C542 004 01 None 9.4.7 IDLE idle 0 0 1/1/1 NA 0 593/590
KINASE#sh dspfarm
DSPFARM Configuration Information:
Admin State: DOWN, Oper Status: DOWN - Cause code: ADMIN_STATE_DOWN
Transcoding Sessions: 0(Avail: 0), Conferencing Sessions: 0 (Avail: 0)
Trans sessions for mixed-mode conf: 0 (Avail: 0), RTP Timeout: 600
Connection check interval 600 Codec G729 VAD: ENABLED
KINASE#config t
Enter configuration commands, one per line. End with CNTL/Z.
KINASE(config)#voice-card ?
<0-1> Voice interface slot #
KINASE(config)#voice-card 0 ?
% Unrecognized command
KINASE(config)#voice-card 0?
% Unrecognized command
KINASE(config)#voice-card 0?
% Unrecognized command
KINASE(config)#voice-card 0/?
% Unrecognized command
KINASE(config)#voice-card 0
^
% Invalid input detected at '^' marker.
KINASE(config)#voice-card 1
^
% Invalid input detected at '^' marker.
KINASE(config)#
KINASE(config)#voice-port 1/0/0
KINASE(config-voiceport)#?
Voice-port configuration commands:
battery-reversal Enable FXO battery-reversal detection
bearer-cap Specify the bear capability
busyout Configure busyout trigger event & procedure
comfort-noise Use fill-silence option
connection Specify Trunking Parameters
cptone Configure voice call progress tone locale
default Set a command to its defaults
description Description of what this port is connected to
dial-type Configure type of dialer for voice
disc_pi_off close voice path when disconnect with PI received
echo-cancel Echo-cancellation option
exit Exit from voice-port configuration mode
impedance Specifies the terminating impedance of the interface
input Configure input gain for voice
music-threshold Threshold for Music on Hold
no Negate a command or set its defaults
non-linear Use non-linear processing during echo cancellation
output Configure output attenuation for voice
playout-delay Configure voice playout delay buffer
pre-dial-delay FXO Pre-dial Delay
ring Number of rings
shutdown Take voice-port offline
signal The signaling type for the interface FXS or FXO
snmp Modify SNMP voice port parameters
station-id Configure station ID
supervisory Configure answer + disconnect supervision options
threshold Threshold [noise] for voice port
timeouts Configure voice timeout parameters
timing Configure voice timing parameters
translate Translation rule
translation-profile Translation profile
trunk-group Configure interface to be in a trunk group
voice-class Set voiceport voice class control parameters
KINASE(config-voiceport)#
Looks like the "voice-port" command works, but not the "voice-card" command.
Similar Messages
-
VOIP home lab with cisco 2620 and VIC-2FXO port
Hi all,
I m considering building a home lab for studying CCVP, the lab would be based on the follow components :
- CUCM 8.X (already installed)
- A couple of soft phones running in VMWARE with IP Blue and CIPC (they are already in place and registered with the CUCM)
- Cisco router 2620 with NM-2V and VIC-2FXO-M2 (for europe, I'm in France)
so here are my questions :
1/ it looks like the NM-2V comes with integrated DSP, so I should not need more DSP, I have got one PSTN analogic line only so I can make only one call at a time, please confirm
2/ my analog line comes via my home internet provider dsl box, i have already tried to connect an analog phone and it works, please confirm the router will be able to receive and place calls
thanks for your help, I m looking forward to begin my voice lab1. Yes, the NM-2V has built-in DSP resources for up to four calls (max voice port density with two 1st generation VICs). You cannot add further DSP chips to the NM-1V/2V, nor would you need to for what it does. You have one PSTN phone line, thus you can only make one call at a time. If you had a second line you could use the other FXO port for a second concurrent call.
2. If the phone line works then it will work with the router to make and receive calls. As Gregory said, just configure dial peers for what you need to do.
Here is some info on the NM-2V:
http://www.cisco.com/en/US/products/hw/modules/ps2617/products_tech_note09186a0080094ac0.shtml -
How to debug "vic-2fxo"'s dialer information?
who can tell the correct way to see the debug information about the vic-2fxo?
once i have used the command" debug dialer events" and " debug dialer packets" in the router. And I can initiate a successful call from remote phone to the Call manger through the vic-2fxo in the router. But I can see any debug information in the router either at the console or at the remote terminal.
Thanks
SincerelyWhat debug information are you looking for. If you are using FXO for voip purposes then debug vpm would show you the voice port signaling events and debug vtsp all would show you debug of vtsp layer when it communicates with the ccapi layer. For voip you can turn on debug voip ccapi inout. There are other deugs that can give you much more verbose information if you want to read through the h225 and h245 messages.
-
Hello
I have a router 2611XM and I'm trying to install a VIC-2FXO card but the router is not taking the card, it has the lights on but when you do sh ver doesn't show up the card. I install the IOS c2600-advipservicesk9-mz.124-25c.bin, still not working.
Any Help
ThanksEven though this is an old thread, I'll answer Tyson's question -
It may help someone else who stumbles across this thread in a search.
The VIC-2FXO you have is not supported with the NM-HD-2V
Look at:
http://www.cisco.com/en/US/customer/products/hw/routers/ps259/products_tech_note09186a00800e73f6.shtml
Second table in section on
"Cisco 17xx, VG200, 26xx, and 2800 Platforms Matrix"
Routers/Gateways
Model
261x, 2x, 5x
2600XM, 2691
Voice Network Module (right)
NM-1V 1 NM-2V 1
NM- HDV
NM-1V 1 NM-2V 1
NM-HD-1V 1 NM-HD-2V 1
NM-HD-2VE 2
NM- HDV
NM- HDV2
VIC (below)
VIC-2FXO, EU
Yes
No
Yes
No
No
No
No
The row is for the VIC-2FXO.
Look at the column 4, which is for your NM-HD-2V on 2600 platforms
It says "No"
The earlier NM-1V or NM-2V is required. That combination says "Yes" -
I am looking to purchase a new 2811 router and need to know if this card will work. It is located in a 1751. Here is the 'show inventory'
NAME: "WIC/VIC 2", DESCR: "2nd generation two port FXO voice interface daughtercard"
PID: 2nd generation two port FXO voice interface daughtercard, VID: 5.0
From what I can tell, a VIC-2FXO will not work in the 2811; it has to be the VIC2-2FXO. So which card is this?
Thanks,
-Matt
EDIT: I answered my own question with a 'show diag' which lists the FRU as VIC2-2FXO. Hopefully this might help someone else out.VIC2-2FXO
Two-port VIC ? FXO (Universal). Also supports Centralized Automatic Message Accounting (CAMA) with software configuration
http://cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b53c7.shtml -
In my environment there is a PBX connecto VIC2-2FXO at router CISCO1751-V. I have an old PBX and when I change the card to VIC-2FXO(EOL), I have from from PBX e works fine. But if I return the new card VIC2-2FXO it doesn't work, even tone is missing. What a real difference between VIC-2FXO and VIC2-2FXO
Hi Almir,
The card is comatible with 1751-4V. The VIC2 cards are the new generation cards. Working wise they are no different. I checked the configs nd they looked kinda incomplete. Usually the FXO works with a "connection plar/trunk". Neither did I notice any voip dial-peers.
Sample config for call flow : (phone---pbx---vic2-fxo---router1--ip---router2---fxs--phone)
voice-port 2/0
cptone BR
connection plar 3000
dial-peer voice 100 voip
destination-pattern 3000
session target ipv4:p.q.r.s
dial-peer voice 1 pots
destination-pattern .T
port 2/0
The above config should be fine for inbound and outbound calls. If this doesn't work please send me the following-
1. Exact call flow eg
2. deb voice ccapi inout
3. debug vpm signal
4. debug vtsp events
5. debug vtsp session
Subhrojyoti -
Difference between VIC2-2FXO and VIC-2FXO
All, kindly advice what is the difference between VIC2-2FXO and VIC-2FXO?
Also I will like to know if I can use VIC-2FXO in a 2821 Router.The difference is the normal evolution of products and technological generations.
You cannot do what you mentioned.
http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a00800e73f6.shtml -
How can we put the report which is generated by the program into spool??
How can we put the report which is generated by the program into spool??
I had generated a file in Unix which had the report but now the requirement has changed.
Regards,
Shashank.Hi Shashank,
If the program is executed in the background and it has the write statement then the spool will automatically generated.
Reward points if useful.
Regards,
Atish -
Can i put my SIM card from my old iphone 5 into my new Iphone 5 i just purcahed? And will my phone start working?
Yes all of the iPhone 5 family use the nano sim, so as long as you did not switch to a phone locked to another network it will work. But you do need to go through the activation/setup procedure with tHat sim.
-
Can I put the 2Gb RAM (X2) from my MacBook Pro into my MacBook? The intel is different (2Ghz not 2.3) and the speed is 2000 not 1333. But they are both DDR3.
I have just upgraded the Pro to 16Gb and the MacBook is SO slow. Just wondering if I could use the old RAM.Full specification of MB5.1 RAM;
204-pin PC3-8500 (1066 MHz) DDR3 SO-DIMM, non-ECC (non parity), unbuffered.
MBP8.1, 8.2 or 8.3;
204-pin PC3-10600 (1333 MHz) DDR3 SO-DIMM, non-ECC (non parity), unbuffered.
PC3 is the same as DDR3. the number is peak transfer rate (approximated).
Further reading suggests your swap may work, but it's not guaranteed. If you get 3 beeps on start up (or the sleep light flashing in bursts of 3), first check it's correctly seated, but be prepared to swap them back.
If you encounter any instability or kernel panics, change them back. -
Having issues when try to burn a disc., which I never had an issue doing. Yesterday when I tried to burn a playlist it says "checking media" but just sits there. I know drive is working because I can put in a purchased cd and can import it into my library, but now it just sits there and hums until I maually eject the disc.Before all this started it said something about that I should "calibrate disc", since then it won't let me do any burning. I can't find any options in " preferences to change anything except the burn speed. Any suggestions? Tried rebooting, tried using my wifes iTunes on same comptuer.
Could you post your diagnostics for us please?
In iTunes, go "Help > Run Diagnostics". Uncheck the boxes other than DVD/CD tests, as per the following screenshot:
... and click "Next".
When you get through to the final screen:
... click the "Copy to Clipboard" button and paste the diagnostics into a reply here. -
Put some data form the databse of SQL Server into SAP and auto general PR?
Dear all,
Can you tell me how I can put some data from the databse of SQL Server into SAP and auto general PR?
Best regards,
Merryzhang
Edited by: merry zhang on Feb 4, 2009 9:10 AMHi Zhang,
If i have understood your question properly, I guess you wanted to create Purchase Requistion automatically right?
Then you have lots of option simpilest one would be create a couple of Z table with all the fields that you require for header and Item.
create a Program and use BAPI function module to create the PR by reading the values from those Z tables. after creation delete the contents from the table. Schedule this program in Background periodically like everyday or weekly once however you would like it to be. So once the table has contents in it and when the program runs it will create the PR's (Purchase Requisition).
You can also use a workflow with the Z table. Once the Z table is filled you can trigger a workflow based on the Table change. I'm not sure like how to do it but I nkow that this process can also be used.
Hope this might have thrown some light upon.
Thanks,
Prashanth -
And then put in rice for 3 days and plugged it into my computer but it keeps flashing the Apple logo and a no charge sign. It also is not connecting to my computer and it does not say "Amelia's iPhone" in iTunes
Put it in rice for another 4 days.
-
I can not put the data of a field(LONG RAW) consulted into a item of a data block
I want to query a field that is LONG RAW(it's a image) and put the data into a item of a data block (in Forms Builder), when i write ":BLOCK.FOTO:=vfoto" i recieve this errors: "bad bind variable ....". How can i put the data of field of my DB and put the data in a item of a data block(in Forms Builder)?.
I can store a image in a table of my DB, but i want to query a image stored in my DB and put it into anothers table, all this on FORMS BUILDER.You have to base the image item on a base table and use EXECUTE_QUERY on that block. You can't do a direct select in PL/SQL into the item
-
Daughter forgets password to Ipod..trys it to many times and it says disabled connect to itunes. So I do so and it shows all the music and junk she has on the ipod but I dont know where or how to unlock the device to where we can use it again..Any iinfo greatly appreciated!!
Disabled
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
Maybe you are looking for
-
Java.lang.IllegalArgumentException: org.apache.fop.svg.SVGElementMapping
Hi, I have an FOP application which presents the data retrieved from database in a PDF format. Now when Iam trying to deploy the FOP application to OC4J and I get the following error. java.lang.IllegalArgumentException: org.apache.fop.svg.SVGElementM
-
Retrieving backed up data from IMac to IPhone 4
Hi I took my IPhone4 to the apple store today as I was receiving an error when trying to update to IOS6. They updated but all of the data was removed form my phone, which I thought was ok as I had backed up to my ITunes. Now I have got home and my IT
-
My finder is now a desktop space.
My finder is now a desktop space.I would rather have the option of running is as a window or a full screen app. Any help would be appreciated.
-
Hi , I am doing import of table using parfile with query option. My import is running is running from 4 hours where as export get completed with in half hours??? Kindly suggest... query_imp.par tables=ABC query=ABC:"WHERE TIMESTAMP BETWEEN '09/20/201
-
Hiding backend URL in BSP iView / connect via portal-server to backend
wrong posting / folder.. pls delete.. Message was edited by: Mario Kölzsch Message was edited by: Mario Kölzsch Message was edited by: Mario Kölzsch