PVDM + Bri Dialin problem
Hi everybody, i configured a c2811 with 2 bri and a pvdm module to accept incoming data connection via modem. Everything is ok except that after user is authenticated suddenly router disconnects connections with irregular time; it could be 2 mins, 5 mins etc... Anyone has an idea about? What it could be? Or if you see something wrong in configuration.
Thanks in advance, Fabio.
Please configure network-clock-select 1 bri 0/0/0 and network-clock-select 1 bri 0/0/1.
Hope this helps, please rate post if it does!
Similar Messages
-
I'm having a problem with PPP dropping connection. I have Solaris8 - (Intel) Everything is going fine then all of a sudden I get this "process_ipd_msg: interface ipdptp0 reports an error " message in the logs and it drops the line and reconnects. (I've included part of the log below)
This problem has been giving me problems for days. I've tried everything I can think of... Anyone have any ideas what is going on here or how I can fix it? How do I find where this "reports an error" is coming from? (ie what the error is)
Any help please.
Thanks,
Michael
Modem: USR 56K External
OS: SunOS krose 5.8 Generic_108529-05 i86pc i386 i86pc
12:01:09 054485 ipdptp0 ppp_diag: [ID 501754 kern.debug] SEND PPP ASYNC 57
Octets NB (AP) VJ_UNCOMP_TCP 45 00 00 34 a0 16 40 00 40
12:01:09 054486 ipdptp0 ppp_diag: [ID 947544 kern.debug] SEND PPP ASYNC 15
Octets NB (AP) VJ_COMP_TCP 50 0a 78 ac 71 75 69 74 0d 0a
12:01:10 054487 ipdptp0 ppp_diag: [ID 462543 kern.debug] RECEIVE PPP ASYNC
57 Octets NB (AP) VJ_UNCOMP_TCP 45 00 00 34 59 08 40 00
12:01:10 054488 ipdptp0 ppp_diag: [ID 697767 kern.debug] RECEIVE PPP ASYNC
72 Octets NB (AP) VJ_UNCOMP_TCP 45 00 00 43 59 09 40 00
12:01:10 054489 ipdptp0 ppp_diag: [ID 505786 kern.debug] SEND PPP ASYNC 57
Octets NB (AP) VJ_UNCOMP_TCP 45 00 00 34 a0 18 40 00 40
12:01:10 054490 ipdptp0 ppp_diag: [ID 946063 kern.debug] SEND PPP ASYNC 57
Octets NB (AP) IP_PROTO 45 00 00 34 a0 19 40 00 40 06 be
12:01:10 054491 ipdptp0 ppp_diag: [ID 546447 kern.debug] RECEIVE PPP ASYNC
57 Octets NB (AP) VJ_UNCOMP_TCP 45 00 00 34 59 0a 40 00
12:01:10 054492 ipdptp0 ppp_diag: [ID 349955 kern.debug] RECEIVE PPP ASYNC
57 Octets NB (AP) IP_PROTO 45 00 00 34 59 0b 40 00 fd 06
12:01:10 054493 ipdptp0 ppp_diag: [ID 589690 kern.debug] SEND PPP ASYNC 57
Octets NB (AP) VJ_UNCOMP_TCP 45 00 00 34 a0 1a 40 00 40
12:01:27 054494 ipdptp0 ppp_diag: [ID 791769 kern.debug] SEND PPP ASYNC 89
Octets (AP) IP_PROTO 45 00 00 54 84 bb 40 00 ff 01 36 c2
12:01:27 process_ipd_msg: interface ipdptp0 reports an error
12:01:27 disconnect: disconnected connection from ipdptp0
12:01:27 054495 ipdptp0 ppp_diag: [ID 221690 kern.debug] RECEIVE PPP ASYNC
27 Octets NB LCP Proto-REJ ID=07 LEN=22 Rej_proto=a234
12:01:27 054496 ipdptp0 ppp_diag: [ID 267406 kern.debug] SEND PPP ASYNC 9
Octets NB (A) IP_NCP Term-REQ ID=ef LEN=4
12:01:28 054497 ipdptp0 ppp_diag: [ID 203052 kern.debug] RECEIVE PPP ASYNC
89 Octets NB (AP) IP_PROTO 45 00 00 54 7e 9b 40 00 fd 01
12:01:28 054498 ipdptp0 ppp_diag: [ID 626626 kern.debug] RECEIVE PPP ASYNC 9
Octets NB (A) IP_NCP Term-ACK ID=ef LEN=4
12:01:28 054499 ipdptp0 ppp_diag: [ID 188677 kern.debug] SEND PPP ASYNC 9
Octets NB LCP Term-REQ ID=f0 LEN=4
12:01:31 054500 ipdptp0 ppp_diag: [ID 424189 kern.debug] SEND PPP ASYNC 9
Octets LCP Term-REQ ID=f1 LEN=4
12:01:34 054501 ipdptp0 ppp_diag: [ID 906425 kern.debug] SEND PPP ASYNC 9
Octets LCP Term-REQ ID=f2 LEN=4
12:01:34 054502 ipdptp0 ppp_diag: [ID 854706 kern.debug] RECEIVE {Unescaped
characters: 0a 0e } PPP ASYNC 69 Octets {BAD FCS} NB (A
12:01:34 054503 ipdptp0 ppp_diag: [ID 146661 kern.debug] RECEIVE PPP ASYNC 9
Octets NB LCP Term-REQ ID=f2 LEN=4
12:01:34 054504 ipdptp0 ppp_diag: [ID 882942 kern.debug] SEND PPP ASYNC 9
Octets NB LCP Term-ACK ID=f2 LEN=4
12:01:34 054505 ipdptp0 ppp_diag: [ID 776435 kern.debug] RECEIVE PPP ASYNC 9
Octets NB LCP Term-ACK ID=f2 LEN=4
12:01:34 054506 ipdptp0 ppp_diag: [ID 494070 kern.debug] PPP DIAG CLOSE
12:01:40 process_ipd_msg: ipdptp0 needs connection
conn(ppp)
Trying entry from '/etc/uucp/Systems' - device type ACU.
Device Type ACU wanted
Trying device entry 'cua/a' from '/etc/uucp/Devices'.
processdev: calling setdevcfg(ppp, ACU)
fd_mklock: okHi,
On a similar occassion wherein I was trying to get Aux Port configured for Remote Dialin (for exec access and not for data) I tried almost 4 USR modems and everytime all the modems would get stuck at the handshake and never be able to complete the process.
However when I changed the modem to a simple make and model, it did work!
I guess its a problem with USR, have you ever tried with some other brand?
Kind Regards,
Wilson Samuel -
Hi,
Hope you can help me with this, Im stuck.
I have a 2500 router with several external modems (US Robotics 56k) connected over asynch cables. the line config is setup to autocommand telnet to a backend server.
When I attempt to dial in, whichever modem answers, it seems to pick up the call, but then it drops almost immediately. The router log shows the same debug message each time:
Jun 18 14:40:20.691: tty1: Modem: HANGUP->IDLE
Jun 18 14:40:22.031: TTY1: Line reset by "Virtual Exec"
Jun 18 14:40:22.031: TTY1: Modem: IDLE->HANGUP
Jun 18 14:40:22.035: TTY1: destroy timer type 0
Jun 18 14:40:22.035: TTY1: destroy timer type 1
Jun 18 14:40:22.039: TTY1: destroy timer type 3
Jun 18 14:40:22.039: TTY1: destroy timer type 4
Jun 18 14:40:22.039: TTY1: destroy timer type 2
Jun 18 14:40:22.727: TTY1: dropping DTR, hanging up
Jun 18 14:40:22.727: tty1: Modem: HANGUP->IDLE
Jun 18 14:40:24.764: TTY1: restoring DTR
Jun 18 14:41:48.646: TTY1: Line reset by "Virtual Exec"
router config:
version 12.0
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname R1
logging buffered 50000 debugging
aaa new-model
aaa authentication login default local
aaa authentication login no_user enable
aaa authentication login noaut none
aaa authentication login noprompt none
enable secret 5 <removed>
username test password 7 <removed>
ip subnet-zero
clock timezone GMT 0
interface Ethernet0
ip address x.x.x.x 255.255.255.0
no ip directed-broadcast
no ip mroute-cache
interface Serial0
no ip address
no ip directed-broadcast
no ip mroute-cache
shutdown
no fair-queue
interface Serial1
no ip address
no ip directed-broadcast
no ip mroute-cache
shutdown
ip classless
ip route 0.0.0.0 0.0.0.0 x.x.x.x
line con 0
transport input none
line 1
no exec-banner
exec-timeout 0 0
no activation-character
autoselect during-login
session-limit 1
no vacant-message
login authentication noaut
modem Dialin
autocommand telnet x.x.x.x 3001 /noecho
terminal-type edit
exec-character-bits 8
special-character-bits 8
transport preferred telnet
transport input all
escape-character BREAK
stopbits 1
flowcontrol hardware
line 2
no exec-banner
exec-timeout 0 0
no activation-character
autoselect during-login
session-limit 1
no vacant-message
login authentication noaut
modem Dialin
autocommand telnet x.x.x.x 3000 /noecho
terminal-type edit
exec-character-bits 8
special-character-bits 8
transport preferred telnet
transport input all
escape-character BREAK
telnet transparent
stopbits 1
flowcontrol hardware
line aux 0
login authentication no_user
line vty 0 4
password 7 <removed>
endHi,
On a similar occassion wherein I was trying to get Aux Port configured for Remote Dialin (for exec access and not for data) I tried almost 4 USR modems and everytime all the modems would get stuck at the handshake and never be able to complete the process.
However when I changed the modem to a simple make and model, it did work!
I guess its a problem with USR, have you ever tried with some other brand?
Kind Regards,
Wilson Samuel -
ISDN BRI L2 problem in Austria
Installing BRI's for South-Africa Embassy in Vienna.Isdn is connected to telco l1is up but L2 shows the following:
Layer 2 Status:
TEI = 255, Ces = 1, SAPI = 0, State = ESTABLISH_AWAITING_TEI
Please help tried everythingHi Stefan,
Have a look at the following;
How about if you add "no dial-peer outbound status-check pots" in global config :
From Zulfiqar in this excellent Cisco ask the Expert Archive;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Expert%20Archive&topic=Network%20Infrastructure&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddaceb2/25#selected_message
or this thread from June of this year;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=IP%20Communications%20and%20Video&topic=IP%20Telephony&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1dda6c90/5#selected_message
Hope this helps!
Rob -
EPCF : Error in Init Method
Hi all,
When i try to run my EPCF , I'm getting the following error , please let me get some suggestion on this.
EXCEPTION]
#1#com.sapportals.portal.prt.component.PortalComponentException: Error in init method
Component : Framework.MyProducer
at com.sapportals.portal.prt.component.PortalComponentContext.init(PortalComponentContext.java:251)
at com.sapportals.portal.prt.core.broker.PortalComponentContextItem.refresh(PortalComponentContextItem.java:267)
at com.sapportals.portal.prt.core.broker.PortalComponentContextItem.getContext(PortalComponentContextItem.java:312)
at com.sapportals.portal.prt.component.PortalComponentRequest.getComponentContext(PortalComponentRequest.java:385)
at com.sapportals.portal.prt.connection.PortalRequest.getRootContext(PortalRequest.java:435)
at com.sapportals.portal.prt.core.PortalRequestManager.runRequestCycle(PortalRequestManager.java:607)
at com.sapportals.portal.prt.connection.ServletConnection.handleRequest(ServletConnection.java:240)
at com.sapportals.portal.prt.dispatcher.Dispatcher$doService.run(Dispatcher.java:545)
at java.security.AccessController.doPrivileged(Native Method)
at com.sapportals.portal.prt.dispatcher.Dispatcher.service(Dispatcher.java:405)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.sap.engine.services.servlets_jsp.server.servlet.InvokerServlet.service(InvokerServlet.java:156)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:390)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:264)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:347)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:325)
at com.sap.engine.services.httpserver.server.RequestAnalizer.invokeWebContainer(RequestAnalizer.java:887)
at com.sap.engine.services.httpserver.server.RequestAnalizer.handle(RequestAnalizer.java:241)
at com.sap.engine.services.httpserver.server.Client.handle(Client.java:92)
at com.sap.engine.services.httpserver.server.Processor.request(Processor.java:148)
at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)
at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)
at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
at java.security.AccessController.doPrivileged(Native Method)
at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:100)
at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:170)
Caused by: com.sapportals.portal.prt.component.PortalComponentException: Cannot find JSP file: MyProducer.jsp
at com.sapportals.portal.prt.core.broker.JSPComponentItem.getComponentInstance(JSPComponentItem.java:132)
at com.sapportals.portal.prt.core.broker.PortalComponentItem.getComponentInstance(PortalComponentItem.java:732)
at com.sapportals.portal.prt.component.PortalComponentContext.getComponent(PortalComponentContext.java:103)
at com.sapportals.portal.prt.component.PortalComponentContext.init(PortalComponentContext.java:242)
My portalapp.xml
<?xml version="1.0" encoding="utf-8"?>
<application>
<application-config>
<property name="SharingReference" value="com.sap.portal.htmlb"/>
</application-config>
<components>
<component name="MyProducer">
<component-config>
<property name="ComponentType" value="jspnative"/>
<property name="JSP" value="MyProducer.jsp"/>
<property name="SecurityZone" value="com.customer.portal/high_safety"/>
</component-config>
<component-profile>
<property name="tagLib" value="/SERVICE/htmlb/taglib/htmlb.tld"/>
</component-profile>
</component>
<component name="MyConsumer">
<component-config>
<property name="ComponentType" value="jspnative"/>
<property name="JSP" value="MyConsumer.jsp"/>
<property name="SecurityZone" value="com.customer.portal/high_safety"/>
</component-config>
<component-profile>
<property name="tagLib" value="/SERVICE/htmlb/taglib/htmlb.tld"/>
</component-profile>
</component>
</components>
<services/>
</application>Hi Bris,
The problem is that the MyProducer.jsp cannot be found (this has absolutely nothing to do with EPCF). Probably you have put it into the wrong path: "This path is relative to the private resources (in PORTAL-INF in PAR) of the portal application", see http://help.sap.com/saphelp_erp2004/helpdata/en/16/d12c413894f823e10000000a155106/frameset.htm
I.e., if you have put it under .../PORTAL-INF/pagelet/MyProducer.jsp, the corresponding portalapp.xml entry must read:
<property name="JSP" value="pagelet/MyProducer.jsp"/>
Hope it helps
Detlev -
Problem in calling BRI from PRI
Hi,
I am having problem in calling BRI from PRI. I am getting below message while debugging. Also note that calling from BRI to PRI is successful.
Mar 2 23:38:22: ISDN BR0/0 Q931: RX <- SETUP pd = 8 callref = 0x04
Sending Complete
Bearer Capability i = 0x8890
Standard = CCITT
Transer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x89
Progress Ind i = 0x8281 - Call not end-to-end ISDN, may have in-band info
Calling Party Number i = 0x2183, '1726601501'
Plan:ISDN, Type:National
*Mar 2 23:38:22: ISDN BR0/0:1: Incoming call rejected, unbindable
*Mar 2 23:38:22: ISDN BR0/0 **ERROR**: host_incoming_call: DIALER ERROR 0x1: b channel 0, call id 0x15E
*Mar 2 23:38:22: ISDN BR0/0 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x84
Cause i = 0x8095 - Call rejected
Pls help me.
Anis
9229109694Dear Dharmesh,
Can u pls explain where to enable PPP Multilink.
Dear p.bevilacqua ,
I did what u told (configure "ppp chap username" under dialer interface), but the problem is same.
Anis -
BRI problems / layer 1 deactivated
Hi there
I could really use some help for this issue. I need to implement a BRI line for voice as backup for a SIP line.
However I cannot make layer 1 come up as active. I know for sure the line is working as attaching a phone to the ISDN2 line makes me able to receive and make calls. So the line is ok from teleprovider side. Must be cable issue, makes a cable according to Cisco doc. "When the ISDN BRI port on the router is configured as an NT port, you must use a "rolled" cable (one with the transmit and receive leads swapped) to connect to a TE interface." But this does not help me still same outcome.
Any help is much appriciated.
Cisco2921 router IOS: 15.0 (1r) with BRI module NT/TE 2gen.
VGW#sh isdn status
Global ISDN Switchtype = basic-net3
ISDN BRI0/0/0 interface
dsl 0, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x80000003
ISDN BRI0/0/1 interface
dsl 1, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 1 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
VGW#sh controllers bri0/0/0
BRI unit 0:
layer 1 operating in LT-T mode.
Layer 1 is DEACTIVATED. (ISDN L1 State F3)
D Channel Information:
idb at 0x294042F4, driver data structure at 0x2941FF40
Infineon Chip Version 0x1
Infineon Registers:
Int. Status Register [ISTA]=0x00, Aux. Int. [AUXI]=0x00
D-channel: Int. Status Reg: [ISTAD]=0x00, Status. Reg: [STARD]=0x40
Mode Reg: [TR_MODE]=0x01
Transceiver Reg: [TR_CONF0]=0x00
Test mode Reg: [TMD]=0x00
IOM Control Reg: [IOM_CR]=0x08
Status Register [STAR]=0x40, Mode Register [MODED]=0xCA
Serial Data Strobe Control Reg: [SDS1_CR]=0x00, [SDS2_CR]=0x00
RX Buffer Descriptor is at 0x30BF37E4, Buffer size 1524
pak=0x3172EF74 data_ptr=0xE1D5FD4 partial_size=0x0
TX Buffer Descriptor is at 0x2940FEBC
pak=0x0 data_ptr=0x0 partial_size=0x0
0 missed datagrams, 0 overruns
0 bad datagram encapsulations, 0 memory errors
0 transmitter underruns 0 d channel collisions
B1 Channel Information:
0 missed datagrams, 0 overruns
0 bad datagram encapsulations, 0 memory errors
0 transmitter underruns 0 d channel collisions
B2 Channel Information:
0 missed datagrams, 0 overruns
0 bad datagram encapsulations, 0 memory errors
0 transmitter underruns 0 d channel collisions
B2 Channel Information:
0 missed datagrams, 0 overruns
0 bad datagram encapsulations, 0 memory errors
0 transmitter underruns 0 d channel collisions
interface BRI0/0/0
no ip address
isdn switch-type basic-net3
isdn overlap-receiving
isdn point-to-point-setup
isdn incoming-voice voice interface BRI0/0/0
no ip address
isdn switch-type basic-net3
isdn overlap-receiving
isdn point-to-point-setup
isdn incoming-voice voiceI had this problem a few months ago and it took several days of investigation and research to figure it out but I got there in the end. Hopefully this will save someone else a lot of frustration!
In short it was mainly sorted by adding the bearer-cap Speech command to my extra voice-ports.
This command specifies whether the 'call' will initialize for voice or data during the setup and can cause the line to drop/disconnect if it is set incorrectly.
FULL DETAILS
My client was using a UC540W-BRI-K9 with 2 phone lines coming in over a single ISDN device connected to a voice-port. They had purchased a plug-in 2-port voice-board to allow them to utilize another 4 phone lines via an extra 2 ISDN devices, however the company who installed this had failed to configure the system properly so even after I activated the extra lines they would always fail to dial-out as above.
The first step was to tell the plug-in voice-board to use the network-clock and set the ISDN-connected BRIs to use the network-clock:
network-clock-participate wic 1
network-clock-participate wic 2
network-clock-select 1 BRI0/1/0
network-clock-select 2 BRI0/1/1
network-clock-select 3 BRI0/2/0
I spent time investigating the BRI configuration, adding a few bits which I think helped activate the lines, although I still had the outgoing call failures on the new lines:
interface BRI0/1/0
no ip address
isdn switch-type basic-net3 <--- Copied this command to the other BRIs
isdn tei-negotiation first-call <--- Added this to all the BRIs
isdn point-to-point-setup
isdn incoming-voice voice
isdn sending-complete
isdn static-tei 0 <--- Added this to all the BRIs
trunk-group ALL_BRI 64 <--- Copied this command to the other BRIs
I then found the voice-ports had a separate configuration independent of the BRIs and the newly connected voice-ports required a couple of commands to be copied from the original, working voice-port. The problem was fixed once I applied the bearer-cap Speech command to the extra voice-ports, along with compand-type a-law (for a European system).
voice-port 0/1/0 <--- The original voice-port connected to the primary ISDN
compand-type a-law <--- Copied to the newly-connected voice-ports
bearer-cap Speech <--- Copied to the newly-connected voice-ports
voice-port 0/1/1 <--- Connected to 2nd ISDN
compand-type a-law
bearer-cap Speech
voice-port 0/2/0 <--- Connected to 3rd ISDN
compand-type a-law
bearer-cap Speech
voice-port 0/2/1 <--- Unused
The compand-type command is used to convert signals from analog to digital and is normally compand-type u-law for North America systems and compand-type a-law for European systems, as explained here:
http://www.cisco.com/en/US/docs/ios/12_3/vvf_r/vrg_c4_ps1839_TSD_Products_Command_Reference_Chapter.html#compand-type -
Problem connecting isdn bri voice interface to pstn
i'm trying to configure my ISDN BRI NT/TE voice interface card (VIC-2BRI-NT/TE) on router 3825 to link to my PSTN provider. This must allow my Cisco IP phones to pass call to the PSTN through my call manager 4.1.
I suscribe to two isdn line. The provider told me that the SWITCH TYPE is VN6 (COTE d'IVOIRE or Ivory Coast).
For my bri configuration, see file "interfaces configuration..."
My problem is that when i pass call from my Ip telephony network, the first call goes well. But after this first call, when i type the command isdn status, i can see that the layer 1 of my isdn interfaces are DEACTIVATED, and after a few minutes, it turn back to ACTIVE. During these minuite, i can't pass any call through my isdn interface.
for outputs of show isdn status command, and isdn debug q931 commands
see file "show isdn status and debug..."
Notice: when the status of the isdn layer is in the deactvated status, i can receive call from the pstn, but i can't passe call to pstn (the state changes to ACTIVE when incomming call from pstn arrive, but still stay DEACTIVATED when outgoing call is initiated)
Please help meI've entered the "isdn transition-delay 1" interface command and things seem to work well.According to the IOS help on my router,this command clears the ISDN D-CHANNEL after a delay of 1 second.
But i would like to get more information on this command, and also on the isdn layer 2 and 3 timers, and even possible on all the "isdn" interface command option.
THANKS -
following is my configuration of 1812.
interface BRI0
no ip address
encapsulation frame-relay IETF
dialer pool-member 1
isdn switch-type basic-net3
isdn point-to-point-setup
interface Dialer0
ip address xx.xx.xx.xx 255.255.255.252
encapsulation frame-relay IETF
dialer pool 1
dialer idle-timeout 0
dialer string XXXXXX
dialer max-call 4095
dialer persistent
frame-relay interface-dlci 16
frame-relay lmi-type q933a
my porblem is this when ever my Line of BRI is fluctuate for any reason my router does not automatically redials. instead i have to restart the router every time.
could any one suggesst me is there any thning wrong in my configuration.
but same configuration works well in 1841 with BRI module installed.
Thanks in advance.
RegardsAlthough you may manually configure dial peers to work with the MLPP for Analog and BRI Endpoints on Cisco IOS Voice Gateways feature, we recommend that you use Cisco CallManager autoconfiguration. Refer URL
http://www.cisco.com/en/US/products/sw/iosswrel/ps5207/products_feature_guide09186a00804202c9.html#wp1050570 -
Problem with unicast videostream using ISDN BRI between 2 876 routers
Hello,
I have two 876 routers with the proper IOS. I configured the ISDN line. It's working fine. Pinging and telnetting vice versa.
On one end there is a videocamera with the encoder (Bosch) connected to the Vlan-side of one router. On the other side of the ISDN line there is a decoder (with monitor) connected to the VLAN side of the outher router.
The encoder is configured to send a videostream to the (ip-address) of the decoder, unicast and 64Kb.
The problem is that the decoder doesn't seem to pickup the MPEG4 video-stream I
t does see the video stream( it shows a jpeg-snapshot which refreshes after several seconds).
Has anyone any idea what the problem could be?
Help appreciated.
With regards,
Jaap Laaij
NetherlandsHi P?,
Yes i do see an increase in packet counters.
What did suprise me today when I changed the network setting, both on encoder an decoder, from udp to HTTP (80). On the monitor the MPG4 stream appeared !?!?!
Although delighted, I don't see why UDP is not recognized by the encoder.
Or, am I fooled by the counters and is the rise of counters due to other traffic and UDP is not let through and HTTP (80) is.
Is it possible UDP goes for another subnet than I put in a static route for and therefore doesn't cross over?
If I seem confused, than your right :( :)
Any thoughts?
Thanx
Jaap -
4FXS-DID configuration problem using BRI to receive/send calls from/to PSTN
Hi to all.
Follow is the partial configuration of my CME.
It has a 4FXS card to use analog phones and faxes, and 4 ISDN Basic Rate interfaces.
On each port of the 4FXS DID card happens the following:
If I enable direct-inward-dial
I can receive calls from PSTN.
Off hooking the analog phone I cannot hear any free line tone. I cannot make any call from that phone.
If I disable direct-inward-dial
I cannot receive directly calls form PSTN.
Callers on PSTN after typing my number, they hear a free tone. Then just typing the extension desired the phone ring.
Off hooking the analog phone I hear a free line tone. I can make normal calls to everyone.
I have half the configuration working.
Where am I wrong?
I really appreciate your help.
Thanks to all.
Giorgio.
CME#sh ver
Cisco IOS Software, 2800 Software (C2800NM-IPVOICEK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2)
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
CME uptime is 2 days, 15 hours, 49 minutes
System returned to ROM by power-on
System restarted at 18:54:45 CDT Fri Aug 2 2013
System image file is "flash:/c2800nm-ipvoicek9-mz.124-24.T3.bin"
Cisco 2811 (revision 53.50) with 249856K/12288K bytes of memory.
Processor board ID FTX1120A08L
2 FastEthernet interfaces
4 ISDN Basic Rate interfaces
16 terminal lines
4 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
1948656K bytes of USB Flash usbflash0 (Read/Write)
497448K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
CME#sh telephony-service
CONFIG (Version=7.1)
=====================
Version 7.1
Cisco Unified Communications Manager Express
isdn switch-type basic-net3
voice translation-rule 1
rule 1 /^2929091\(..\)/ /\1/
rule 2 /^2929091\(.\)/ /\1/
rule 3 /^02929091\(..\)/ /\1/
rule 4 /^02929091\(.\)/ /\1/
voice translation-rule 2
rule 2 /\(.*\)/ /02929091\1/
voice translation-rule 10
rule 1 /\(^......$\)/ /0\1/ type national national plan isdn isdn
rule 8 /\(^......$\)/ /00\1/ type international international plan isdn isdn
voice translation-profile PSTN-IN
translate calling 10
translate called 1
voice translation-profile PSTN-OUT
translate calling 2
interface BRI0/0/0
description Isdn channels 1 & 2
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/0/1
description Isdn channels 3 & 4
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/1/0
description Isdn channels 5 & 6
no ip address
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/1/1
description not used
no ip address
shutdown
isdn switch-type basic-net3
isdn timer T310 60000
isdn overlap-receiving T302 3000
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
voice-port 0/0/0
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 1 & 2
voice-port 0/0/1
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 3 & 4
voice-port 0/1/0
translation-profile incoming PSTN-IN
translation-profile outgoing PSTN-OUT
compand-type a-law
description Connessione con CO Telecom channels 5 & 6
voice-port 0/1/1
description Disponibile
voice-port 0/2/0
input gain 14
connection plar 83
description Interphone 40
station-id name Citofono
station-id number 40
caller-id enable
voice-port 0/2/1
cptone IT
description Ced 35
station-id name CED
station-id number 35
caller-id enable
voice-port 0/2/2
cptone IT
description FAX_1 50
station-id name FAX_1
station-id number 50
caller-id enable
voice-port 0/2/3
cptone IT
description FAX_2 60
station-id name FAX_1
station-id number 60
caller-id enable
dial-peer voice 1001 pots
description **Sends call to PSTN line 1-2**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/0
dial-peer voice 2001 pots
description **Receives calls coming from PSTN line 1-2**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/0
dial-peer voice 1003 pots
description **Sends call to PSTN line 3-4**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
dial-peer voice 2003 pots
description **Receives calls coming from PSTN line 3-4**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/1
dial-peer voice 1005 pots
description **Sends call to PSTN line 5-6**
destination-pattern 0T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 2005 pots
description **Receives calls coming from PSTN line 5-6**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/1/0
dial-peer voice 2035 pots
description **Receives calls coming from PSTN to Extension 35**
answer-address 35
destination-pattern 35$
incoming called-number 35
port 0/2/1
dial-peer voice 2040 pots
description **Receives calls coming from PSTN to Extension 40**
destination-pattern 40
incoming called-number 40
no digit-strip
direct-inward-dial
port 0/2/0
dial-peer voice 2050 pots
description **Receives calls coming from PSTN to Fax 50**
destination-pattern 50
incoming called-number 50
no digit-strip
direct-inward-dial
port 0/2/2
dial-peer voice 2060 pots
description **Receives calls coming from PSTN to Fax 60**
destination-pattern 60
incoming called-number 60
no digit-strip
direct-inward-dial
port 0/2/3
CME#Hi Paolo.
Sorry for the delay. I was on holiday.
I would like to keep separate incoming calls from outgoing calls.
So I decided to keep two dial peers for every BRI interface.
I followed your suggestion on eliminate commands:
"incoming called-number" on FXSs,
various "progress_ind" on BRIs
Also I eliminated "direct-inward-dial" on FXSs,
Today I reconfigured and right tested the dial peers as following:
! Bri Interfaces
dial-peer voice 1001 pots
description **Sends call to PSTN line 1-2**
destination-pattern 0T
port 0/0/0
dial-peer voice 2001 pots
description **Receives calls coming from PSTN line 1-2**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/0
dial-peer voice 1003 pots
description **Sends call to PSTN line 3-4**
destination-pattern 0T
port 0/0/1
dial-peer voice 2003 pots
description **Receives calls coming from PSTN line 3-4**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/0/1
dial-peer voice 1005 pots
description **Sends call to PSTN line 5-6**
destination-pattern 0T
port 0/1/0
dial-peer voice 2005 pots
description **Receives calls coming from PSTN line 5-6**
destination-pattern 2929091..
incoming called-number .T
direct-inward-dial
port 0/1/0
! FXS interfaces
dial-peer voice 2035 pots
description **Receives calls coming from PSTN to Extension 35**
destination-pattern 35
no digit-strip
port 0/2/1
dial-peer voice 2040 pots
description **Receives calls coming from PSTN to Extension 40**
destination-pattern 40
no digit-strip
port 0/2/0
dial-peer voice 2050 pots
description **Receives calls coming from PSTN to Fax 50**
destination-pattern 50
no digit-strip
port 0/2/2
dial-peer voice 2060 pots
description **Receives calls coming from PSTN to Fax 60**
destination-pattern 60
no digit-strip
port 0/2/3
Thanks a lot Paolo. :-)
Giorgio. -
Hi, I have configured a VIC2-2BRI-NT/TE in a 2801 Voice Gateway (IOS 12.4(11)T4) placed in Lisboa (the operator is TELEPAC), and I can't make inbound/outbound calls. The interface config is:
interface BRI0/2/0
no ip address
isdn switch-type basic-net3
isdn overlap-receiving
isdn point-to-point-setup
isdn incoming-voice voice
The 'sh isdn status' command:
Global ISDN Switchtype = basic-net3
ISDN BRI0/2/0 interface
dsl 4, interface ISDN Switchtype = basic-net3
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 66, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 4 CCBs = 0
The Free Channel Mask: 0x80000003
And the 'debug isdn q921':
*Jan 25 13:29:40.480: BRI0/2/0 : Unexpected indication (4) in f3 code
*Jan 25 13:29:40.484: ISDN BR0/2/0 Q921: L2_EstablishDataLink: sending SABME
*Jan 25 13:29:40.484: ISDN BR0/2/0 Q921: User TX -> SABMEp sapi=0 tei=66
*Jan 25 13:29:40.496: ISDN BR0/2/0 Q921: User RX <- DMf sapi=0 tei=66
*Jan 25 13:29:45.380: ISDN BR0/2/0 Q921: User RX <- SABMEp sapi=0 tei=0
*Jan 25 13:29:46.380: ISDN BR0/2/0 Q921: User RX <- SABMEp sapi=0 tei=0
*Jan 25 13:29:47.380: ISDN BR0/2/0 Q921: User RX <- SABMEp sapi=0 tei=0
*Jan 25 13:29:48.376: ISDN BR0/2/0 Q921: User RX <- SABMEp sapi=0 tei=0
*Jan 25 13:29:49.388: ISDN BR0/2/0 Q921: User RX <- IDCKRQ ri=0 ai=0
*Jan 25 13:29:50.384: ISDN BR0/2/0 Q921: User RX <- IDCKRQ ri=0 ai=0
*Jan 25 13:30:01.376: ISDN BR0/2/0 Q921: User RX <- SABMEp sapi=0 tei=0
*Jan 25 13:30:02.384: ISDN BR0/2/0 Q921: User RX <- SABMEp sapi=0 tei=0
*Jan 25 13:30:03.380: ISDN BR0/2/0 Q921: User RX <- SABMEp sapi=0 tei=0
*Jan 25 13:30:04.384: ISDN BR0/2/0 Q921: User RX <- SABMEp sapi=0 tei=0
*Jan 25 13:30:05.388: ISDN BR0/2/0 Q921: User RX <- IDCKRQ ri=0 ai=0
*Jan 25 13:30:06.388: ISDN BR0/2/0 Q921: User RX <- IDCKRQ ri=0 ai=0
*Jan 25 13:30:17.380: ISDN BR0/2/0 Q921: User RX <- SABMEp sapi=0 tei=0
*Jan 25 13:30:18.384: ISDN BR0/2/0 Q921: User RX <- SABMEp sapi=0 tei=0
*Jan 25 13:30:19.384: ISDN BR0/2/0 Q921: User RX <- SABMEp sapi=0 tei=0
*Jan 25 13:30:20.384: ISDN BR0/2/0 Q921: User RX <- SABMEp sapi=0 tei=0
*Jan 25 13:30:21.388: ISDN BR0/2/0 Q921: User RX <- IDCKRQ ri=0 ai=0
*Jan 25 13:30:22.392: ISDN BR0/2/0 Q921: User RX <- IDCKRQ ri=0 ai=0
I have not idea to solve this issue. Has anybody any idea?
Thanks.
Regards.Hi, I don't know the lines features of de BRI. How can it influence in the configuration?
I have made the change in the interface (isdn static-tei 0), and now the layer 2 shows multiple_frame_established:
Global ISDN Switchtype = basic-net3
ISDN BRI0/2/0 interface
dsl 4, interface ISDN Switchtype = basic-net3
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 4 CCBs = 0
The Free Channel Mask: 0x80000003
But when I do a call I can hear a very noisely voice (I think it is an autoattendand console, but I can not understand anything). This is the output of the 'debug isdn q931' command:
*Jan 25 22:46:09.697: ISDN BR0/2/0 Q931: Applying typeplan for sw-type 0x1 is 0x
0 0x0, Calling num 3017
*Jan 25 22:46:09.701: ISDN BR0/2/0 Q931: Applying typeplan for sw-type 0x1 is 0x
0 0x0, Called num 217805000
*Jan 25 22:46:09.701: ISDN BR0/2/0 Q931: TX -> SETUP pd = 8 callref = 0x0C
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x81
Preferred, B1
Calling Party Number i = 0x0081, '3017'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '217805000'
Plan:Unknown, Type:Unknown
*Jan 25 22:46:09.917: ISDN BR0/2/0 Q931: RX <- SETUP_ACK pd = 8 callref = 0x8C
Channel ID i = 0x89
Exclusive, B1
*Jan 25 22:46:09.977: ISDN BR0/2/0 Q931: RX <- CALL_PROC pd = 8 callref = 0x8C
Display i = 'CHAMADA EM PROGRESSO'
*Jan 25 22:46:10.505: ISDN BR0/2/0 Q931: RX <- ALERTING pd = 8 callref = 0x8C
Progress Ind i = 0x8488 - In-band info or appropriate now available
Display i = 'A CHAMAR'
*Jan 25 22:46:10.581: ISDN BR0/2/0 Q931: RX <- CONNECT pd = 8 callref = 0x8C
Display i = 'IMPULSOS = 2'
Date/Time i = 0x0801191630
Date (yr-mm-dd) = 08-01-25
Time (hr:mnt:sec) = 22:48:76
Connected Number i = 0x0083, '217805000'
*Jan 25 22:46:10.585: %ISDN-6-CONNECT: Interface BRI0/2/0:1 is now connected to
N/A N/A
*Jan 25 22:46:10.585: ISDN BR0/2/0 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x0
C
*Jan 25 22:46:10.613: ISDN BR0/2/0 Q931: RX <- FACILITY pd = 8 callref = 0x8C
Facility i = 0x91A1130202906E020122300AA1053003020102820100
Protocol Profile = Remote Operations Protocol
0xA1130202906E020122300AA1053003020102820100
Component = Invoke component
Invoke Id = 36974
Operation = AOCDChargingUnit
*Jan 25 22:46:15.577: ISDN BR0/2/0 Q931: RX <- INFORMATION pd = 8 callref = 0x8
C
Display i = 'IMPULSOS = 2'
*Jan 25 22:46:35.317: %ISDN-6-DISCONNECT: Interface BRI0/2/0:1 disconnected fro
m unknown , call lasted 24 seconds
*Jan 25 22:46:35.317: ISDN BR0/2/0 Q931: TX -> DISCONNECT pd = 8 callref = 0x0C
Cause i = 0x8090 - Normal call clearing
*Jan 25 22:46:35.465: ISDN BR0/2/0 Q931: RX <- RELEASE pd = 8 callref = 0x8C
Facility i = 0x91A1130202906F020122300AA1053003020102820101
Protocol Profile = Remote Operations Protocol
0xA1130202906F020122300AA1053003020102820101
Component = Invoke component
Invoke Id = 36975
Operation = AOCDChargingUnit
Display i = 'IMPULSOS = 2'
*Jan 25 22:46:35.469: ISDN BR0/2/0 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x
0C
When the call is connected, the telnet window to the router stops working, and when the call is finished it works again. How can I solve that?
Regards. -
Hi all
Now my Cisco C40 use two BRI Europe isdn lines to connect the another site's tandbeg system.
The C40 can connected the remote site successful, but the remote site's screen is so small.
is there anyone konw it?Note: Your question would be better placed in the TelePresence section of the forums where these devices are more actively discussed than in the Conferencing section you've posted in - I'd suggest you move your discussion via the Edit button at the top of the page.
Can you please describe a bit more what you mean by the "screen is so small". The fact that you are using ISDN should have no impact on how the screen displays.
Can you also provide more information on how your C40 is configured - ie, what is the output device, what resolution is it set to on the C40, are you specifying a non-default layout? Is the other end presenting and hence you're seeing a presentation layout?
Wayne
Please remember to rate responses and to mark your question as answered if appropriate. -
Problem whit cisco 2921 + EVM-HD-8FXS/DID whit CUCM
Hello everyone.
I have the following problem that I am not able to resolve. I define a new connection BRI.
I can make calls seamlessly between the Cisco Unified Communications Manager (version: 8.5.1.10000-26) and Cisco 2921 (CISCO2921-V/K9).
But when you receive calls from BRI Cisco receives the call but the Cisco Unified Communications Manager does not tranfere for Ext
And I can not understand why. In other BRI interfaces do not have this problem.
This configuration here that I'm using.
Current configuration : 17238 bytes
! Last configuration change at 18:02:34 PORT Mon Apr 2 2012 by admin
! NVRAM config last updated at 18:02:56 PORT Mon Apr 2 2012 by admin
! NVRAM config last updated at 18:02:56 PORT Mon Apr 2 2012 by admin
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname <<omitted>>
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
enable secret 5 <<omitted>>
aaa new-model
aaa authentication login default none
aaa authentication login <<omitted>>
aaa accounting connection h323 start-stop group radius
aaa session-id common
clock timezone PORT 0 0
clock summer-time PORT recurring last Sun Mar 1:00 last Sun Oct 1:00
network-clock-participate slot 1
network-clock-participate wic 0
network-clock-participate wic 1
network-clock-participate wic 2
network-clock-participate wic 3
network-clock-select 1 BRI0/0/0
network-clock-select 2 BRI0/1/0
network-clock-select 3 BRI0/2/0
network-clock-select 4 BRI0/3/0
no ipv6 cef
ip source-route
ip cef
no ip domain lookup
ip domain name <<omitted>>
multilink bundle-name authenticated
isdn switch-type basic-net3
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed- <<omitted>>
enrollment selfsigned
subject-name cn= <<omitted>>
revocation-check none
rsakeypair TP-self-signed- <<omitted>>
crypto pki certificate chain <<omitted>>
<<omitted>>
quit
voice-card 0
dsp services dspfarm
voice call send-alert
voice call disc-pi-off
voice call carrier capacity active
voice rtp send-recv
voice service voip
no ip address trusted authenticate
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
h323
modem passthrough nse codec g711ulaw
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice class h323 1
h225 timeout tcp establish 5
voice translation-rule 1
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 2
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
rule 4 /^21 <<omitted>>/ /21 <<omitted>>/
rule 5 /^21 <<omitted>>/ /21 <<omitted>>/
rule 6 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 3
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 4
rule 1 /^0/ /400/
rule 2 /^/ /21 <<omitted>>/
voice translation-rule 5
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /^21 <<omitted>>/ /21 <<omitted>>/
rule 3 /^21 <<omitted>>/ /21 <<omitted>>/
voice translation-rule 11
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 12
rule 1 /^21 <<omitted>>/ /21 <<omitted>>/
rule 2 /.*/ /21 <<omitted>>/
voice translation-rule 13
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 14
rule 1 /.*/ /21 <<omitted>>/
voice translation-rule 15
rule 1 /.*/ /21<<omitted>>/
voice translation-rule 21
rule 1 /^./ /0&/
voice translation-rule 22
rule 1 /^./ /0&/
voice translation-rule 25
rule 1 /^./ /0&/
|
voice translation-rule 23
rule 1 /^./ /0&/
voice translation-rule 24
rule 1 /^./ /0&/
voice translation-rule 32
rule 1 /^212104974/ /21 <<omitted>>/
rule 2 /.*/ /212104975/
voice translation-profile INLINE_EMPA
translate calling 22
translate called 2
voice translation-profile INLINE_EMPB
translate calling 23
translate called 3
voice translation-profile INLINE_EMPC
translate calling 25
translate called 5
voice translation-profile INLINE_EMPE
translate calling 24
translate called 4
voice translation-profile INLINE_EMPD
translate calling 21
translate called 1
voice translation-profile OUTLINE_EMPA
translate calling 12
voice translation-profile OUTLINE_EMPA_NT_FAX
translate calling 32
voice translation-profile OUTLINE_EMPB
translate calling 13
voice translation-profile OUTLINE_EMPC
translate calling 15
voice translation-profile OUTLINE_EMPE
translate calling 14
voice translation-profile OUTLINE_EMPD
translate calling 11
license udi pid CISCO2921/K9 sn <<omitted>>
hw-module pvdm 0/0
hw-module sm 1
username admin privilege 15 password 0 <<omitted>>
redundancy
ip ssh time-out 60
ip ssh authentication-retries 2
class-map match-all Voz
match access-group 100
policy-map QoS
class Voz
priority 200
set precedence 5
class class-default
fair-queue
gw-accounting aaa
attribute acct-session-id overloaded
acct-template callhistory-detail
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
ip address <<omitted>> 255.255.0.0
ip access-group BLOCK in
load-interval 30
duplex auto
speed auto
h323-gateway voip interface
h323-gateway voip bind srcaddr <<omitted>>
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
description $ES_LAN$
no ip address
shutdown
duplex auto
speed auto
interface BRI0/0/0
description EMPD N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/0/1
description Ecotel EMPD N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/1/0
description EMPA N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation first-call
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/1/1
description EMPA N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/2/0
description EMPB N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/2/1
description Ecotel EMPB N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI0/3/0
description EMPE N:
no ip address
isdn switch-type basic-net3
isdn tei-negotiation preserve
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI0/3/1
description Ecotel EMPA N
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/0
description B EMPC N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn static-tei 0
interface BRI1/1
description Ecotel EMPE N:
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/2
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/3
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/4
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/5
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/6
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
interface BRI1/7
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn static-tei 0
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip rtcp report interval 500
ip access-list extended BLOCK
deny ip any host <<omitted>>
deny ip any host <<omitted>>
deny ip any host <<omitted>>
deny ip any host <<omitted>>
permit ip any any
ip radius source-interface GigabitEthernet0/0
radius-server host <<omitted>> auth-port 1647
radius-server host <<omitted>> acct-port 1647
radius-server key <<omitted>>
radius-server vsa send accounting
control-plane
voice-port 0/0/0
translation-profile incoming INLINE_EMPD
translation-profile outgoing OUTLINE_EMPD
compand-type a-law
cptone PT
voice-port 0/0/1
compand-type a-law
cptone PT
voice-port 0/1/0
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA
compand-type a-law
cptone PT
voice-port 0/1/1
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA_NT_FAX
compand-type a-law
cptone PT
voice-port 0/2/0
translation-profile incoming INLINE_EMPB
translation-profile outgoing OUTLINE_EMPB
compand-type a-law
cptone PT
voice-port 0/2/1
translation-profile incoming INLINE_EMPB
translation-profile outgoing OUTLINE_EMPB
compand-type a-law
cptone PT
description Ligacao Acesso GSM
bearer-cap Speech
voice-port 0/3/0
translation-profile incoming INLINE_EMPE
translation-profile outgoing OUTLINE_EMPE
compand-type a-law
cptone PT
voice-port 0/3/1
translation-profile incoming INLINE_EMPA
translation-profile outgoing OUTLINE_EMPA
compand-type a-law
cptone PT
description Ligacao Acesso GSM
bearer-cap Speech
voice-port 1/0/0
compand-type a-law
cptone PT
voice-port 1/0/1
compand-type a-law
cptone PT
voice-port 1/0/2
compand-type a-law
cptone PT
voice-port 1/0/3
compand-type a-law
cptone PT
voice-port 1/0/4
compand-type a-law
cptone PT
voice-port 1/0/5
compand-type a-law
cptone PT
voice-port 1/0/6
compand-type a-law
cptone PT
voice-port 1/0/7
compand-type a-law
cptone PT
voice-port 1/0/8
translation-profile incoming INLINE_EMPC
translation-profile outgoing OUTLINE_EMPC
compand-type a-law
cptone PT
voice-port 1/0/9
compand-type a-law
cptone PT
voice-port 1/0/10
compand-type a-law
cptone PT
voice-port 1/0/11
compand-type a-law
cptone PT
voice-port 1/0/16
compand-type a-law
cptone PT
voice-port 1/0/17
compand-type a-law
cptone PT
voice-port 1/0/18
compand-type a-law
cptone PT
voice-port 1/0/19
compand-type a-law
cptone PT
ccm-manager music-on-hold
no mgcp package-capability res-package
no mgcp package-capability fxr-package
no mgcp timer receive-rtcp
mgcp profile default
dial-peer voice 1 pots
description +++++ Dial-peer +++++
incoming called-number .
direct-inward-dial
port 0/0/0
dial-peer voice 10 pots
description touchwise
destination-pattern 1T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/0
dial-peer voice 20 pots
description globalmove
preference 1
shutdown
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 30 pots
description globaltemp
shutdown
destination-pattern 3T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 40 pots
description EMPE
destination-pattern 4T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/3/0
dial-peer voice 100 voip
preference 1
destination-pattern .
session target ipv4:10.35.2.1
voice-class codec 1
no vad
dial-peer voice 21 pots
description globalmove
preference 2
shutdown
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 101 voip
preference 2
destination-pattern .
session target ipv4:10.35.2.2
voice-class codec 1
no vad
dial-peer voice 24 pots
description globalmove
preference 1
destination-pattern 59[1236].......
port 0/3/1
forward-digits 9
dial-peer voice 25 pots
description globalmove
preference 1
destination-pattern 500T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 26 pots
description globalmove
preference 2
destination-pattern 500T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 27 pots
description globalmove
preference 1
destination-pattern 5[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/0
dial-peer voice 28 pots
description globalmove
preference 2
destination-pattern 5[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/1/1
dial-peer voice 34 pots
description globalTemp
preference 1
destination-pattern 39[1236].......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/1
forward-digits 9
dial-peer voice 35 pots
description globalTemp
preference 1
destination-pattern 300T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 37 pots
description globalTemp
preference 1
destination-pattern 3[123678]T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/2/0
dial-peer voice 14 pots
description empd
preference 1
destination-pattern 19386648.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 15 pots
description empd
preference 1
destination-pattern 19365483.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 16 pots
description empd
preference 1
destination-pattern 19341347.......
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/1
forward-digits 9
dial-peer voice 50 pots
description EMPC
destination-pattern 5T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 1/0/8
gateway
timer receive-rtp 1200
gatekeeper
shutdown
call-manager-fallback
max-conferences 4 gain -6
transfer-system full-consult
ip source-address 10.35.2.250 port 2000
max-ephones 100
max-dn 300
transfer-pattern 09........
transfer-pattern 02........
transfer-pattern 0.........
transfer-pattern 000T
transfer-pattern 4...
keepalive 10
time-format 24
date-format dd-mm-yy
shutdown
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
login authentication touchwise
transport input ssh
line vty 5 15
login authentication touchwise
transport input ssh
scheduler allocate 20000 1000
ntp master 5
endIf t i "Translation Pattern Configuration" switch to another "Partition" existing or internal it works.
If change back for the new i create. It does not work.
So I must be some flaw i made in Cisco Unified CM. -
Hi,
we have ISR 2801 router with 2xVIC2-2BRI-NT/TE, 1xVIC2-2FXS and PVDM2-8, IOS ver.c2801-spservicesk9-mz.124-9.T7.bin. We can see ISDN BRI ports but cannot see FXS ports.
Any help?
here some outputs from router:
sh ver.
Cisco 2801 (revision 7.0) with 235520K/26624K bytes of memory.
Processor board ID FCZ121412Q8
2 FastEthernet interfaces
4 ISDN Basic Rate interfaces
2 Voice FXS interfaces
1 DSP, 4 Voice resources
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
126976K bytes of ATA CompactFlash (Read/Write)
sh invent
NAME: "chassis", DESCR: "2801 chassis"
PID: CISCO2801 , VID: V04 , SN: FCZ121412Q8
NAME: "VIC 0", DESCR: "2nd generation two port BRI voice interface daughtercard"
PID: VIC2-2BRI-NT/TE , VID: V02 , SN: FOC12093QZW
NAME: "WIC/VIC/HWIC 1", DESCR: "2nd generation two port BRI voice interface daughtercard"
PID: VIC2-2BRI-NT/TE , VID: V02 , SN: FOC12093QL0
NAME: "WIC/VIC 2", DESCR: "2nd generation two port FXS voice interface daughtercard"
PID: VIC2-2FXS , VID: V01 , SN: FOC12121ZWM
NAME: "PVDM 0", DESCR: "PVDMII DSP SIMM with one DSP with half channel capcity"
PID: PVDM2-8 , VID: V01 , SN: FOC12085ZJS
sh voice port summ
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
============== == ============ ===== ==== ======== ======== ==
0/0/0 1 bri-voice up dorm none none y
0/0/0 2 bri-voice up dorm none none y
0/0/1 1 bri-voice up dorm none none y
0/0/1 2 bri-voice up dorm none none y
0/1/0 1 bri-voice up dorm none none y
0/1/0 2 bri-voice up dorm none none y
0/1/1 1 bri-voice up dorm none none y
0/1/1 2 bri-voice up dorm none none yI found out a solution. The problem is generated by insufficient DSP resources (PVDM2-8, I need more...).I had rearranged the position of the card and of course I've lost one ISDN BRI port. The result is as follow:
sh voice port summ
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
============== == ============ ===== ==== ======== ======== ==
0/0/0 1 bri-voice up dorm none none y
0/0/0 2 bri-voice up dorm none none y
0/0/1 1 bri-voice up dorm none none y
0/0/1 2 bri-voice up dorm none none y
0/1/0 -- fxs-ls up dorm on-hook idle y
0/1/1 -- fxs-ls up dorm on-hook idle y
0/2/0 1 bri-voice up dorm none none y
0/2/0 2 bri-voice up dorm none none y
voice-port 0/0/0
voice-port 0/0/1
voice-port 0/1/0
voice-port 0/1/1
voice-port 0/2/0
I hope that this will help anyone with this situation.
Maybe you are looking for
-
Windows 7 Driver for HP Deskjet 995ck
Please help me, i can't find the driver for this printer, i was searching in "drivers and suport" but it isn't...
-
Hi friends, [please forgive me if i am posting this in the wrong forum, all seems same to a fresher] Now, to my problem..i need a suggestion, a way or a method to implement the following! I am supposed to create a servlet that reads data from oracle
-
Query to get list of employees having photo attached with their profile and query needed to extract the January to April timesheets approved in oracle on 6th May 2008
-
Please assist...when i am trying to login following error is occuring .... Enter user-name: / as sysdba ERROR: ORA-01031: Message 1031 not found; No message file for product=RDBMS, facility=ORA
-
Where is my Assets folder?
I've been playing with the Flex Builder 3 and I've made many projects but I don't see any Assets folder? I see it referenced in tutorials and the developer's guide.