Px4-300d stuck on boot 75% - HELP!!!

Hello all,
Yesterday I upgrade the NAS to the latest firmware: Firmware Version 4.1.104.31360 for px4-300d
Today, I've noticed that the network into the NAS is really slow and the NAS was stuck. I did a hard reset and now the NAS is stuck on 75% for almost an hour and it is also not accesiable via the network.
Is there way to overcome this issue? I have lots of data inside without any backup plan behind.
Thx,
Arix
Solved!
Go to Solution.

Hi there,
I wish I could help.
Unfortunatelly, I never had this file. no one provided it for me. only the local service center took care for this problem by restoring the firmware. they refused to give it to me.
If you do get it, it would be great if you can share it. (in case we would have this problem again).
Cheers,
A

Similar Messages

Stuck in boot need help badly

Hp pavilion p6-2103wb My Hp was workin perfectly fine then I tried to boot it and it just gets stuck in a boot loop and keeps turning on and of and on and off I opened it up and did what most people said to do which is take out the small battery and put it back in and it still doing it I also notice that my ram chip is loose and can just pull it out without undoing the latches and it wiggles side to side and when I retired to turn it on my first time it beeped like 3-5 times pause and did it again if you have any info on how to fix this ill be glad and extremely happy for your help thanks

Jokeonthego, welcome to the forum.
If you can pull the memory module out of the slot without opening the latches, I don't believe that it is seated properly. You need to open the latches and carefully place the module into the slot and push down until it snaps into place. Here is a guide to help you. Read it thoroughly. There is a section that shows how to install it.
The beeps that you are hearing are BIOS beep codes.
Please click the "Thumbs Up+ button" if I have helped you and click "Accept as Solution" if your problem is solved.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee.

Iomega px4-300d will not boot

So I have been running this in my home lab for my ESXi and HyperV clusters.I always shut off when done testing and maybe has a total of 200 hours on it.
Today I powered on my lab this AM and was running fine till tonight. Went to delete a VM from disk and it failed and noticed NAS was off. Tried to reboot, screen and power light flash once.
Now that is all it does. If you plug in or hit power button everything gets power for a second. Lights, LED, CPU and case fan then all goes off.
Tried reset but can't get power to it for 4 seconds to reset. Reseated RAM and all connections, no change. Don't have another comparable power supply but light is green on brick, will see if can test with DMM.
Pretty sure it is hosed but figured for the expense these are it was worth a post at least before I build something more reliable and cost effective.

Were you able to check the output of the power supply? Also a drive failure could prevent it from booting. You could try drive isolation but pulling one at a time or booting with only one at a time and see if it helps.

Px4-300d, no gui access, stuck 95%, lost shares, unstable

Hello,
i'm having a TON of issues with a px4-300d unit with 2x1tb drives:
1) with sw 4.0 (cant remmber the exact subversion) webgui stops responding after random days, but otherwise unit still is accesible
2) snapshots simply stopped working(generated) months ago when webgui stopped working, last ones are from september, in fact one of the snapshots made itself into a public share!
3) yesterday afternoon uniot could not be accessed anymore, after a powercylce it gets stuck in 95%, following another thread i removed disk 1 and it booted, but it lost ALL shares(in webgui, if you go to shares it stays there for a minute then empty) but i can see the volumes in the disk management.
Powercycled then readded drive 1, booted ok started rebuilding, same, no shares.
upgraded to 4.1.104.31360, i completed setup wizard yet status keeps telling me i need to complete setup :/.
Shares are STILL empty AND i have no "add" button or anything, it just stays there.
Checked drive status there's no smart failure or reallocs, dmesg also is not showing any particular error.
now it's rebuilding the array but i have no way to create shares or anything else
This is a RMAed unit from february 2014(prev unit failed similar to this one, but instead of losing the shares, it lost all DATA inside them, after debugging it turns the internal usb flash drive was corrupted).
OFC the unit is now out of warranty...
All in all so far it's more reliable to put data on a floppy drive than on this unit, it fails in the most basic of functions which is to safely keep data, confidence in this model unit is zero

Wesley,
it's raid 1
i checked it in the support log package for smartctl
188 is not present, the other 2 values are at zero on both drives.
Drives are Hitachi Ultrastar A7K2000 (the ones that came with the nas itself).
After the reconstruction is complete i did a fs check and rebooted, shares ae definititely still gone but i can't create new ones!
when i press the create shaes it stays there in "waiting" for a minute then the share dialogs apear, i select the volume i want and create a "test" share then the gui stopped responding, i reopened it, went to shares, nothing, create new share "test" and it tells me "A Share already exists with the name 'test'." Yet nothing is there and if i browse via SMB or FTP nothing is there
i need to fix this urgently!

Blackberry z10 help | My Mac cannot recognize the phone and my phone stuck at booting %99 for 6 hours nothing happened

My Blackberry z10 , Stuck at %99 Boot , and my Mac OSX doesn't recognize it?. i have latest Blackberry Link Version

The funniest part of the whole situation, Apple Care explained it to me as some kind of feature. The told me how to adjust the time when my computer sleeps and recommend I don't shut it down, let it sleep and "instant wake". I would bet if you called them about your Macbook, they would suggest you just close the lid and let it sleep rather than shutting it down.
Basically shutdown and restart have a problem and the solution is to not shutdown is how they explained it to me. They kept saying buzz words like "instant on" and "fast wakeup". My computer already could sleep and wakeup fast, but now shutdown and restart don't work right. I called them 3 times about it, but since they use these buzzwords, sounds like Lion is meant for a Macbook Air or a Mac with an SSD. If you have a normal hard disk, some of the saving/versions/resume features take too long to be written to the disk on shutdown. And when you start again, it takes a long time to reload the system to it's previous point.
Even if I uncheck the box to reopen windows on next start, it reopens them anyways.
If they can't give me a better explaination or some kind of fix, I will have to go back to Snow Leopard. I use my Mac in a production environment and depend on stability. They assured me before I upgraded that it would be stable and all the new saving and versions features could help my productivity. So far it's not helping me and downright annoying. You need to close all your windows before you close the program... if you have 5 windows open in terminal or textedit... every time you launch, they will launch all those windows. I just really want versions, not resume it seems.
But I can deal with it opening a million windows, just can't take it getting stuck on booting or not shutting down properly. This is a "feature" that should be fixed. LOL

PX4-300d is blocked in startup with 95% for 2 days already ! HELP !

Hi
My PX4-300d 4 disks 1 Tb , has 1 year and gave an alert about disk01 . Made a restart from EMC control panel ( normally this was solved this way in my old Iomega NAS) and now after power up a bar with 95% is presented on LCD and i cant get acess to nothing . this is already for 48 h , cant be a rebuild of the RAID , itsblocked ...
status led is off -
drive led is blinking sometimes
What shall i do to try to recover my info?
1-power off ?
2-remove and substitute drive that gave error? theorically system should work with only 3 drives ,
3-back button reset ?
Regards
Solved!
Go to Solution.

I'm sorry, I thought you already had a spare drive available. If you bought your device a year ago and registered it, then it should still be in warranty. Or if you have the original purchase receipt, they will be able to update your warranty and replace the hard drive for you per the warranty.
You might have to shut down the device when you replace the hard drive (I would shut the device down anyway to avoid further problems and data loss). Your data should still be there as long as no other drives fail. If you need to do data recovery on the hard drives, you can connect them to a Linux based device that will be able to read from the drives and retrieve the data.
Have questions and need answers?
Search the database for answers to FAQ's, software/driver downloads, tutorials, news, features and more!
LenovoEMC Support & Downloads
LenovoEMC North America Support Contact Page

Unable to enable security and create admin user after reset - px4-300d

Our px4-300d became inaccessible a few days ago. I couldn't get to any shares from any machine, and I couldn't get to the admin console. When I checked the unit, there was no indication that anything was wrong (ie - the panel didn't show any failure, I didn't get any emails indicating a failure, and there were no lights offering a clue to what was wrong). However the unit was completely frozen...the buttons on the front would not scroll through the different information on the panel.
I attempted to reset the device using the pinhole on the back, but the device wouldn't respond, so I had to power it down using the button on the front. When I tried to power it back up, it would come on for about one second, then immediately power off. I pulled all 4 drives out and powered it on again without any drives. This time it came up completely and I got a message on the panel that drives were missing. I started putting the drives in one at a time and the device recognized them all and I was able to login to the admin console. However, all the shares were missing and I received an email that the Storage Pool was degraded. I rebooted the device from the admin console and when it came back up, it started reconstruction. After a few hours, it completed, but I still had no shares and couldn't create any new shares. I also did not see any of my users, including the admin account I was logged in with. I tried to create a new user, and also tried creating a user I knew existed and neither one worked. The screen would just flash but nothing would show up. At this point, I decided to try to reset using the pinhole on the back of the device to reset the admin user so I could just create a new one. So, now I'm stuck at the 'Enable Security' screen. Every time I try to create an admin account, it just flashes and returns me to the same 'Enable Security' window.
Now what?
Solved!
Go to Solution.

If you are unable to get into it you will not be able to do the factory reset. You can try booting in buy removing one disk at a time. If you are still unable to then tech support should be able to supply you with the imager and try flashing it. I would keep it at 4.0.8 also,

My HP Pavailion 15-n020tu Stuck at Booting in Windows 8.1 Pro when I enable Hyper-V?

Hi,
I'm using HP Pavailion 15-n020tu Stuck at Booting in Windows 8.1 Pro when I enable Hyper-V. And I have to enable Hyper-V to test my Windows Phone Apps in MS Visual Studio? Mty friend Dell Laptop does not facing this problem with same configuration which I have. Then why me are facing this problem?
Help Me?
I tried on Windows 8 Pro but again same problem.
So many things I tried updating Windows, Updating drivers but failed.

Hello @Vikas_Kumawat80,
Welcome to the HP Forums, I hope you enjoy your experience!
I understand that you are looking to enable Virtualization on your notebook computer, and I would be happy to be of assistance!
While I do not have any experience with Virtualization, I do recommend taking a look at this resource on How to Enable and Use Client Hyper-V, as well as Run virtual machines on Windows 8.1 with Client Hyper‑V. I am not certain if this processor has hardware virtualization support, it appears that Windows 8.1 pro and enterprise may have built in capabilities.
If you require further assistance on this, you might have to contact Microsoft on the topic.
I hope this helps!
Best Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

My MBP 15" stuck at boot up on Lion!

My MBP 15" stuck at boot up on Lion! I have MBP 15" Mid 2010 with Mac OS X lion installed but after upgrading from Snow leopard to Lion all the problems start to happen ! I will explain them:
1-boot stuck.... I tryed to use these steps (Command+alt+P+R) but it didn't work ! and i need to leave my computer 3 days without using in order to work !
2-Quick Time Player crashing + Google Chrome Crashing + iPhoto crashing + mouse lag
3- Some times i can't use the brightness key on my keyboard.
4- It really hot some times ( I know its from the i7 Chip)
these are my system info:
-MacBook Pro 15-inch Mid 2010
Processor 2.66 GHz Intel Core i7
Memory 4 GB 1067 MHz DDR3
Graphics Intel HD Graphics 288 MB
Software Mac OS X Lion 10.7.2 (11C74)
I bought it before 7 months
please help me !

Have you run the hardware test that came with the computer?
http://docs.info.apple.com/article.html?artnum=303081

Urgent-stuck on booting windows screen-need a method to shutdown

My MacBookPro13 mid2009 stuck on booting windows. I can't restart, I can't shutdown, is there something for emergency shutdown? I tried to hold power button, but nothing. Now is running on battery hopping to shutdown and to work after.
Thanks for your help

i tried to hold down the power button for minutes and for nothing...thanks for your reply
I ran out of battery, switched it on and everything works fine now....
in the future how do I turn off if holding down the power button does not work?
Message was edited by: nairpic20

IPod Touch stuck on Apple Logo HELP!!!

My iPod Touch 4g is stuck on the Apple logo. I have tried the home button and power button together and it keeps going back to the Apple Logo. And then it is stuck there. Please help!!!

http://ipod.about.com/od/iphonetroubleshooting/f/Iphone-Stuck-At-Apple-Logo.htm
Basic troubleshooting steps
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101
 In Memory of Steve Jobs 

Disable PX4-300d power on automatically

I have PX4-300d running 4.0.2.9960 for evaluation purpose. After supply power to the unit, it immediately power on automatically. Can I change this behavior to keep it power off?
Solved!
Go to Solution.

kositapan,
You are correct, this is the behavoir of the device when it initially detects an active power supply is plugged in.
There is no settings or workaround for this as it is based on the hardware itself. The best thing that can be done to prevent the auto-boot is to keep the unit plugged in and shut it off as normal when the unit is not in use. If the unit is shut off it is not consuming power and would prevent the auto-boot up.
Have questions and need answers?
Search the database for answers to FAQ's, software/driver downloads, tutorials, news, features and more!
LenovoEMC Support & Downloads
LenovoEMC North America Support Contact Page

Px4-300d port forward iptables 50000- https

Hello. I've searched for similar problems but they weren't exactly the same.
I now need to open a https connection to my px4-300d to share folders to specific users.
I already open a portforward to SSH connection which is working fine.
ssh my.ip -p 50001 gets me to mynas.internal.ip:22
I've created a similar rule on port 50000 to port 443, and it starts to connect. I get the certificate out of date error, but then the connections just hangs there on an empty page.
On wireshark I can't see much more, only that my router/pc starts the TLSv1 session, but right after it sends a [FIN, ACK]
Any ideas please?
Thanks and regards.
Dave
Solved!
Go to Solution.

That is not fully true. Once you know the external ip adress of your network you can access your device both via https and ftp. eg.g. https://<external-ip> or ftp://<user-name>:<user-password>@<external-ip>.
(have not checked if this is true when cloud has never set up)
Bearing this in mind you can configure your router to use an own dyn-service with same portforwarding rules as with the cloud..........
Various PCs / Laptops ( sorry I still really love Dell and Fujitsu ;-))
Supporting Customers ix2s and ix4s -- Love Networking ( not only technically ).
I am not a Lenovo Employee.
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!

PX4-300D blocked 95%

Hi,
Yesterday I switched on the PX4-300D and it was blocked starting up at 95%. I don't have access to the web page and I can't do anything.
I shutted down pressing the power button for a long time and I restarted it but it keeps at 95%
I have sent an email to the support contact but I haven't receive an answer.
What can I do?
Thanks.

Hello danijoint
Usually devices hanging at 95% boot is due to a firmware or disk error.
I recommend that you try the following:
-- power off th unit, re-seat all disks, then try booting again.
-- If you were receiving an error for a specific disk before this began, please remove the disk and try booting without it.
-- try swapping disk 1 with one of the other disks in the unit while powered down. Then try booting again.
-- If the above does not work, you can try disk/bay isolation by trying to boot the unit each disk one at a time, we recommend trying each disk in each bay.
-- If there is still no change, try booting the unit without disks to see if the unit can boot on it's own as it should.
Please contact support if there is not change or if it can't boot on it's own.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Stuck at boot up

Mac mini is stuck at boot up. What to do?

Could be many things, we should start with this...
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.
If 10.7.0 or later...
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partitirion & use Disk Utility from there to Repair the Disk.
If that doesn't help Reinstall the OS.

Px4-300d stuck on boot 75% - HELP!!!

Similar Messages

Maybe you are looking for