Pxi 1033 with expresscar​d 8360

Hello,
I have a PXI 1033 Chassis with ExpressCard 8360. I connect it to laptop using ExpressCard.
I want to connect it to PC desktop. Would you please tell me how can I connect. What kind of board i need to connect ExpressCard to PC desktop.
Best regards

There are 2 options for using your PXI 1033 with a desktop.  You can buy an NI PCIe-8361 to go in your desktop, then switch the cable between your desktop (with the NI PCIe-8361) and your laptop (with the ExpressCard-8360).  Or you can buy an ExpressCard adapter for your computer.
If you go the adapter route, you need to get one that plugs into a PCIe slot.  ExpressCard supports 2 interfaces: PCIe and USB.  On a "real" ExpressCard slot, both interfaces are available on the connector.  Some adapters plug into USB and only provide the USB interface, which works fine for ExpressCards that use the USB interface.  Some adapters plug into a PCIe slot and have a cable that plugs into a USB header on the motherboard, so it can support both interfaces (PCIe and USB).
The ExpressCard-8360 uses PCIe, so any adapter that connects via USB simply won't work.  Also note that the card retention isn't very good, and the slot won't support hot-plug like a native ExpressCard port.
- Robert

Similar Messages

  • Poor PXI IO performanc​e on Latitude E6410 with ExpressCar​d 8360

    Hello,
    I have a Dell Latitude E6410 with a Core-i5 M520 which is giving me very poor io performance when using an ExpressCard 8360 card to connect to a PXI Rack.
    The sustained IO rate that I can get appears to be about 1/3 of that that I can get using the same ExpressCard on a Dell Latitude E6400 (with a Core2Duo processor).
    I am using the A05 bios (latest at time of writing) on the E6410.
    Wade.

    I am running Windows XP (32 bit) sp3 in both cases.
    The E6410 has 4GByte of memory fitted.
    The E6400 has 2GByte of memory fitted.
    I have also use the same ExpressCard 8360 via a PXIe to ExpressCard Adaptor in a Desktop machine with similar performance figures to the E6400 - i.e. much better than the E6410.
    The Desktop Machine is an HP Compaq D7900 with 4GByte of memory, Core2Duo E8500 also running Windows XP sp3 (32 bit).
    Also, on the Desktop, I am running NI PXI Platform Services 2.3.2 and NI-Visa runtime version 4.3.
    On the E6410, I am running NI PXI Platform Services 2.5.2 and NI-Visa runtime version 4.6.
    I no longer have access to the E6400 so I am not sure what sofware versions were installed. However, they are unlikely to be new than the versions installed on the E6410.
    Wade.

  • URGENT: PXI-1033 and DAQmx problem

    I bought new laptop with Express Card slot Dell Inspiron 6400. I have PXI-1033 with integrated MXI bridge, Express Card 8360 and PXI-modules: PXI-6251, 6115, 5114 and 4071. I installed drivers 8.3 and plugged in PXI modules into PXI-1033. I first power up PXI-1033 and than power up laptop (with Express Card in it). Laptop can not start, again can not, blue window, and at last start. In MAX is listed PXI chassis with bridge and all modules, but mx is not listed and I can not use it from LabVIEW. What is the problem?

    Hi,
    To clarify, do the PXI modules show up under DAQmx devices?  What color is the Link LED on the 1033?  Do the cards all show up in Windows Device Manager correctly?  Also, are you able to power on the laptop successfully now every time, or does is have trouble booting each time you try and start it up?
    Have you inspected the MXI cable for bent pins or any visible damage?
    Thanks!
    Adam W
    Applications Engineering
    National Instruments

  • NI-PXI 1033

    Hello All,
    I got a new PXI 1033 with PXI 6602 already installed and I have NI PCIe 8361. I have Installed all the device drivers what I got in the package.
    NI PCIe 8361 is connected to PCIE port in my desktop computer.
    I am unable to detect any modules in MAX, what should I do to see PXI 6602, pls see the attached image.
    I am new to PXI usage, so confused where to look at
    Thanks in adv

    Try following the steps given in the troubleshooting guide:
    http://digital.ni.com/public.nsf/allkb/484F81E6570​AD803862569ED007AAA41?OpenDocument
    Also, try deleting the MAX database and detecting the chassis again:
    http://digital.ni.com/public.nsf/allkb/2C7480E8569​87FFF862573AE005AB0D9
    Regards,
    Vaibhav.

  • I got Internal Software Error -223044 with my PXI-4472, PXI-1033 and NI expresscar​d-8360 DaqMx 8.8

    When i running the self test of the board in MAX i got error -223044, anyone that has some ideas?? 
    STALT

    Hey Stalt,
    This particular internal error begs me ask a few questions.
    1) Has this 4472 ever been used with DAQmx?
    2) How old is this 4472?  When was it bought from NI?  Can you give me the revision letter of the board?  That is found by looking for a number printed on the board that usually begins with "ASSY", then there are several other numbers/letters, but the one letter I care about is the letter right before the "-"  So it would look like ASSY11111111E-01 so the revision would be "E"
    3) Do you have another PXI system (with DAQmx) that you can initialize this 4472 in? 
    Let me know
    -gaving
    Software Engineer
    National Instruments 

  • MAX does not recognize PXI-4056 DMM module with PXI-1033 chassis

    New to NI PXI chassis.   Using the PXI-1033 chassis with several installed modules.  I am able to see the chassis and two of the modules in MAX, but my PIX-4065(DMM) module is not listed/found.  Any advice?

    I have to ask the stupid questions first.  Do you have NI-DMM installed in your computer?  Is the DMM card fully inserted (I have seen people not lock the card in and expect it to work)?
    There are only two ways to tell somebody thanks: Kudos and Marked Solutions
    Unofficial Forum Rules and Guidelines

  • AIM ARINC board not detected with MXIe in a PXI-1033 chassis

    Hi,
    I have a PXI-1033 chassis with NI PXI-6229 and AIM boards (ARINC 429 & AFDX) linked to a PC with MXIe.
    Windows can't attribute enough ressources to this device (indicated in the devices manager) so I can't install drivers for my boards.
    If I only put NI PXI-6229 in my chassis, all is OK.
    If I only put AIM boards in my chassis, Windows doesn't boot.
    I tried with a PXI-1036 chassis linked to my PC with MXI-4, all is running correctly (NI and AIM boards).
    Is there anyone who detects a problem of compatibility between AIM boards and MXIe links, and what is the solution ?
    Thanks for answers.
    Matthieu

    Mmonterrat,
    Problems like this are quite often caused by the computer's BIOS.  Is there a BIOS update for your PC, and have you tried a different computer?
    You can get more information here:  http://digital.ni.com/public.nsf/websearch/05B7131814A5DDA38625710F006BB098?OpenDocument
    Robert

  • PXI-4070 with PXIe-1062Q+NIe-8360+Labtop Why? Max not found instrument.

    Dear all
    my condition
    PXI-4070 with PXIe-1062Q+NIe-8360+Labtop
    Window XP SP3
    NI-DMM 3.1
    Why? Max not found instrument.
    found PCI Device "PXI10:15::INSTR
    see picture
    How to fix this problem?
    Best Regard,
    Sermsak.
    Attachments:
    PXI-4070.jpg ‏42 KB

    Hello, 
    Is it possible to take another picture of MAX? That one is very pixilated and I can't quite make out the configuration/error. Does the chassis show up? Every now and then MXI compatibility software is needed for certain BIOS versions so this may be the cause. Did the system work ever before?
    Thanks,
    Eric E.

  • Suitable Laptop for PXI-1033

    I am using a PXIe-8360 with a PXI-1033 and am trying to find a laptop that is compatible with this system.  NI states that not all laptops work with this configuration and has a list of laptops that do have been tested at (http://zone.ni.com/devzone/cda/tut/p/id/5035).  This list is outdated and NI does not give any criterion on how to select a laptop that will work with this system on the webpage.  We have purchased an Acer 5680 and it doesn't seem compatible.  Is there a more recent list of laptops that are compatible?

    Hi PP83,
    I am afraid that the knowledgebase article you located (http://zone.ni.com/devzone/cda/tut/p/id/5035) has the most up-to-date information regarding compatibility between laptops and the Expresscard-MXI for PXI and PXI Express.  National Instruments is actively testing motherboards and laptops so that we can comment on compatibility with our MXI products. 
    For information on motherboards, desktops, and workstations compatible
    with MXI products, you can create a service request with National Instruments PXI Support group at ni.com/support.
    Regards,
    Anna M.
    National Instruments

  • NI PXI-4065 attached to PXI-1033 strange problem

    Hi all,
    I have a NI PXI-1033 Chassis together with NI PXI 4065 DMM and NI PXI 6514 device.
    The problem that I have is very annoying. When I restart my computer or install a new NI feature, the two NI PXI-6514 and PXI 4065 are no longer available as shown at the picture attached and I have to reinstall the drivers in order they to function properly. Why is this happening? Is it normal? 
    I will appreciate every help because it is urgent and important. Thank you! 
    Best,
    Iliya Gurov 
    Attachments:
    problem.JPG ‏42 KB

    I know this topic is ancient but I'm having a similar problem with my system:
    PXI-1033 (thru external PC / PCIe)
    DAQmx 9.2.2
    LabVIEW 8.5
    Windows 7 (32-bit)
    When starting MAX it gives the MAXPXITimeout error. Then MAX crashes most of the time or when it works, none of the devices are "present" according to MAX, i.e no initialize, fail self-test, etc. I tried this command "net start nidevldu" and I get a "windows system error 5 - access denied". So I ran the command prompt as administrator and then the NI Device Loader "successfully started". Now MAX works OK and all my devices are working, until next reboot. Is this a permission issue? I tried changing the NI Device Loader service to log as an admin, but no luck. After rebooting the same issue.
    Appreciate the help. Thanks,

  • PXI-1033 power up causes PC to boot up

     I have a PXI-1033 chassis connected to a Windows 7 PC via MXI-Express cable. Both the PC and PXI chassis are off. When I push the power button on the PXI chassis, the PC turns on. I cannot figure out the cause of this. Thanks.

    habsfan,
    This is expected behavior.  The PXI-1033 attempts to wake the host PC when it's turned on as a convenience so you can power up the whole system with a single switch.  The mechanism it uses is the PCIe WAKE# signal.
    Is it a problem for you, or are you just suprised by it?  I don't think there's a way to disable it on the PXI-1033, but there may be other ways.  Many systems have an option to enable or disable waking the system from PCIe cards, so you could look through the BIOS options of your PC.  Or, if you power on the chassis 4-5 seconds before connecting the MXI cable it shouldn't wake the PC.
    - Robert

  • PXI-1033 fan specificat​ions

    The PXI-1033 chassis powers up (2 green LEDs) and then shuts down in about 5 seconds.  The fan does not spin.   Unplugging all PXI boards does not help.    Found procedure for replacing fan.  Is this the likely cause ?

    It may be worth a try, but I would bet it is a faulty power supply.
    For this chassis, you must get in touch with NI, and send it in for repair in order to replace the power supply.
    You can contact the Applications engineering department by visiting ni.com/ask and creating a Service Request.
    Peter Flores
    Applications Engineer

  • PXI-1033 Linux Support

    Hi,
    I have a setup with one PC connected to a USB-6009 and PXI-1033 chassis.
    On windows both of the hardware work perfect.
    Now I want to switch to Linux.
    I installed
    (1) NI-DAQmx Base 3.4 - SUSE, RedHat
    (2) PXI Platform Services 2.6 - Linux - Beta
    on a Scientific Linux 5.5
    Everything went pretty well, no errors. I answered yes to all questions
    Now, when I run lsdaq, only USB6009 is seen.
    nipxi/nipxiconfig -l all shows nothing.
    Is PXI-1033 supported on Linux ?

    The PXI chassis is configured as the following
    Slot 2,3 PXI-6255
    Slot 4-6 PXI-6723
    Connected to PC using PXIe-8361
    nipxiconfig did not identify any card or chassis.
    However, I believe the hardware connection is OK as I have the following lspci result
    lspci
    02:00.0 PCI bridge: PLX Technology, Inc. PEX 8505 5-lane, 5-port PCI Express Switch (rev aa)
    03:03.0 PCI bridge: PLX Technology, Inc. PEX 8505 5-lane, 5-port PCI Express Switch (rev aa)
    04:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200(A) PCI Express-to-PCI Bridge (rev 03)
    05:0b.0 Class ff00: National Instruments Unknown device 70ff
    05:0c.0 Class ff00: National Instruments Unknown device 70ff
    05:0d.0 Class ff00: National Instruments Unknown device 70ff
    05:0e.0 Class ff00: National Instruments Unknown device 71e1
    05:0f.0 Class ff00: National Instruments Unknown device 71e1

  • Why should I restart my PC after every switch OF+ON of PXI-1033+5102

    Hi. I have NI  PXI-1033 chassis + PXI-5102 digitizer PXI-8430 (RS232). When I start the PC (Win XP) everything works perfectly. However, when I switch OFF+ON the chassis - nothing works (see img below) till I restart the computer.
    The question is how to do everythin work without restarting the PC?
    Thanks a lot.

    Dear Westves,
    You need to reboot your computer each time you want to re-establish connection between your PXI chassis/controller with your PC. 
    I'm afraid there is no work around for this issue.
    With Regards,
    Sammy Z.

  • Hi am trying to save Data into a write to measurement file vi using a NI PXI 1042Q with a real time mode but it is not working but when i run it with uploading it into the PXI it save in to the file

    Hi am trying to save Data into a write to measurement file vi using a NI PXI 1042Q and DAQ NI PXI-6229 with a real time mode but it is not working but when i run it without uploading it into the PXI it save in to the file please find attached my vi
    Attachments:
    PWMs.vi ‏130 KB

     other problem is that the channel DAQmx only works at real time mode not on stand alone vi using Labview 8.2 and Real time 8.2

Maybe you are looking for