PXI-2532 switch cannot be read in MAX

Hey Guys, I have a PXI-1036DC Chassis with a PXI-2532 switch. I am sure I
have setup the hardware correctly as the switch passes the self test. However
when I try and create a new virtual device I am not able to pick the PXI-2532
switch. Any idea why this would be the case? I have tried the 'configure NI
switches' button and the switch does even appear here. Also tried adding new
logical names and driver sessions but still have no luck.
If someone could please help me with this problem it would be greatly
appreciated.
Nikini

Hi Nikini,
Please continue this thread here.
Best,
Adam
Academic Product Manager
National Intruments

Similar Messages

How to obtain 16 x 64 configuration using PXI-2532 switch

Hello,
We have a PXI 1042 chasis with PXI-8106 microcontroller and PXI-2532 switch. With this switch and NI TB-2641 we are able to configure the system as 8 x 64 switch. We would like to configure switch as 16 x 64 matrix . After some research I found out that we might need to use two PXI-2532 switches to acheive this. My question is let us suppose we configure two switches as 8 x 32 matrices then how can one switch access the elements on the other switch (In order to make this 16 x 64)? Is this possible ?What are the available alternatives?
Thanks,
kartik

Hi Kartik,
We have a really great developer zone article on combining switches, I think you'll find most the information your looking for in there.
Matrix Switch Expansion Guide
I also found the following screen shot in the NI switches help.
It looks like this would be easiest if you had the TB 2642, which would allow you to do column expansion with two 8x64 setups (to make a 16x64).
Let us know if you have any further questions.
Thanks
Scott M.
Applications Engineer
National Instruments

NI Switch Executive error when attempting to add NI PXI-2566 switch to new virtual device.

I just loaded Switch Executive and am wanted to explore its capabilities. I have a PXI system that I am setting up. Currently I have PXI-2566 cards in slots 8 and 9.
I was following the NI Switch Executive help documentation "Creating a Virtual Device" and attempted to create a virtual device with the 2566 modules and I got this error;
Error xBFFA000A occurred.
Failure loading driver module.
The driver for the DAQmx switch is not loaded.[DeviceXI1Slot9_ivi]
Attachments:
SwitchExecutiveError_01.bmp ‏229 KB
SwitchExecutiveError_MAX.bmp ‏364 KB

I had not loaded the "NI-DAQ 7" software that came with the 2566 switch card. I assumed that since MAX showed that I had version 7.2 of DAQmx that I was already up to date.
I received a new PXI-2532 switch, and when I got a "driver not found" error in Switch Executive when I tried to add the 2532 to a new virtual device, I had second thoughts on running the setup/install from the new discs.
After running the software install, I was able to add the 2566 switches to a virtual device in Switch Executive. However, the 2532 failed.
Error xBFFA4B4A occurred.
DAQmx Error -200181 occurred:
Channel name specified is not valid for the switch device.
Device: PXI1Slot10
Channel Name: r4
Attachments:
SwitchExecutiveError_02.bmp ‏35 KB

Vad gör "self test" för PXI-2532

Vilka tester utför "self test" för PXI-2532 switch board?
Testar den att varje relä fungerar?
Kan man utföra ett "self test" programatiskt från labview?
/Dan

Hey Nikini,
The first thing we need to check is that the required software is installed. From your post, it looks like you're trying to create a virtual device with NI Switch Executive (NISE). Can you please let me know which version of NISE you're using? To do this, open up Measurement and Automation Explorer (MAX) (should be on your desktop, or Start»Programs»National Instruments»Measurement and Automation) and then expand the Software tab:
While you're in there, let me know which versions of NI-DAQmx and NI-Switch you have installed.
Next, let's open up the NI-Switch Soft front panel (Start»Programs»National Instruments»NI-Switch»NI-Switch Soft Front Panel) and see if you can close relays in there.
-John Sullivan
Analog Engineer

How to wire up and use 256 points at a time on the PXI-2532

I have a PXI chassis with a PXI-2532 512-Crosspoint Matrix Switch Module, a TB-2640 connected to it, and a PXI-4072 FlexDMM and LCR meter.
I am trying to use the DMM to make measurements of something connected to the switch matrix. What I can't seem to figure out, is since the matrix is a 1 wire 4x128 matrix, how do you connect 256 points when there are only 128 conductors in the ribbon cables that attach to the 2640? There are 2 banks of 8, each with 16-pins, on the TB-2640, that seem to be wired internally together. I would like to utilize 256 points in the 512 matrix at a time, and currently I have the DMM hooked up to r0 and r1 to take the measurements. How would I hook up r2 and r3, in the same matrix?
If you are really confused I can explain further, but I haven't found anything that shows how you would actually connect 256 wires to the 2532, when there are only 128 columns. Any information helps.
Thank you.

Since the matrix is a 4x128, there are 4 rows and 128 columns to which you can connect devices under test (DUTs). You can not connect 256 different DUTs because there are not 256 connections. The points refer to the switches inside the card rather than the actual signals.
Here's a bit more info:
http://www.ni.com/white-paper/4453/en#toc3
Also I would post future switch questions here:
http://forums.ni.com/t5/Switch-Hardware-and-Software/bd-p/320
I hope this helps,
Eric E.

After upgrading recently I got this message: "The file 'iTunes Library.itl' cannot be read because it was created by a newer version of iTunes." The music/video files are still on my MacBook Pro. Is it because I'm still on 10.5.8? How do I fix this?

For your reference I’m using a MacBook Pro running 10.5.8. Several weeks ago on a Monday I received an upgrade for iTunes. When Tuesday arrived I attempted to log in so that I could download the latest freebie song(s). I was met w/this message: “The file ‘iTunes Library.itl’ cannot be read because it was created by a newer version of iTunes.”
The music/video files are still on my Mac (I’ve verified that via Searchlight), but I’m unable to open the program. Since I know that 10.5.8 is rapidly becoming prehistoric, could it be that the newest iTunes isn’t compatible w/this particular OS? I’d like to switch up, but understand that the newest OS won’t work on a Mac of this vintage (6 years old). In addition, my Adobe products (all CS2) won’t work w/anything newer than 10.5.8, so I’m reluctant to go to a newer OS (I just can’t afford the Adobe upgrade $$$ @ this point).
Is there any way to get a download of an “old” iTunes version? If there were, I’d simply refuse any future upgrades until my personal economy allows me to stop working as if it were 2006. Please advise, somebody!

I don't know how you received an upgrade for iTunes. You make it sound like it was sent to you. At most your computer will tell you of a new version and you tell it to download it and install it. However, a computer will not do this for a version which is incompatible. iTunes 10.7 came out a few weeks ago but your computer would not notify you and even if it did, 10.7 would refuse to install on your computer. So this part isn't making a lot of sense.
Two ways to get the 'newer version' message. One is to open your library on a computer running a newer version, and then try to open it with an older version. Usually happens when the library is on an external and used with multiple computers. The second way is if you have multiple versions of itunes installed on your computer.
The newest (and likely the last) iTunes for OSX 10.5.8 is iTunes 10.6.3 which has been out for quite a while.
iTunes 10.6.3.25 - http://support.apple.com/kb/DL1575

20gb iPod, error 1418, "disk cannot be read from or written to", and others

I am having a series of serious issues with my 4th gen 20gb. I have tried restoring it several times, syncing if and when it restores, then restoring it again when it tells me "disk cannot be read from or written to". Sometimes when I try restoring it i get the "unknown error 1418" message, so I disconnect the iPod and try again; sometimes it restores, sometimes it doesn't. I have also tried plain resetting it (select+menu) and that either gives me the dead smiley ipod or a folder with an exclamation point.
What can I do to salvage my beloved iPod?
Thanks for any and all help.

If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
http://docs.info.apple.com/article.html?artnum=60983
If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
Make sure you do all the following “TRYs”
A. Try to wait 30 minutes while iPod is charging.
B. Try another FireWire or USB through Dock Connector cable.
C. Try another FireWire or USB port on your computer .
D. Try to disconnect all devices from your computer's FireWire and USB ports.
E. Try to download and install the latest version of iPod software and iTunes
http://www.apple.com/itunes/download/
For old and other versions of iPod updater for window you can get here
http://www.ipodwizard.net/showthread.php?t=7369
F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
Intermediate Level
A. Try to connect your iPod with another computer with the iPod updater pre-installed.
B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
For Mac computer
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iTunes 7 and click “Restore”
For Window computer
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iTunes 7 and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“HP USB Disk Storage Format Tool”.
http://discussions.apple.com/thread.jspa?threadID=501330&tstart=0
C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
Tips
a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iTunes 7.
b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
http://discussions.apple.com/thread.jspa?messageID=2364921&#2364921
Advance Level
A. Diagnostic mode solution
If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
iPod 1G to 3G: "Menu" and "Play/Pause"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
iPod 1G to 3G: "REW", "FFW" and "Select"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
B. Format your iPod with a start disk
I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
If none of these steps address the issue, your iPod may need to be repaired.
Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
Or visit your local Apple Retail Store http://www.apple.com/retail/
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ or ifixit at your own risk
http://www.ipodresq.com/index.php
http://www.ifixit.com/
Just in case that you are at the following situation
Your iPod warranty is expired
You don’t want to pay any service charges
You are prepared to buy a new one
You can’t accept the re-sell value of your broken iPod
Rather than leave your iPod as paper-weight or throw it away.
You can try the following, but again, only do it as your last resort and at your own risk.
Warning !!!! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
Last Resort Level
1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
Exclamation point and folder and nothing else
http://discussions.apple.com/thread.jspa?messageID=3597173#3597173
Exclamation point and folder and nothing else
http://discussions.apple.com/thread.jspa?messageID=2831962#2831962
What should I do with my iPod? Send it or keep it?
http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
Strange error on iPod (probably death)
http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
Sad Face on iPod for no apparent reason
http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
Meeting the Sad iPod icon
http://askpang.typepad.com/relevanthistory/2004/11/meeting_thesad.html#comment-10519524
Sad faced iPod, but my computer won’t recognize it?
http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
iPod Photo: unhappy icon + warranty question
http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
4th Gen iPod Users - are we all having the same problem?
http://discussions.apple.com/message.jspa?messageID=2235623#2235623
Low Battery, and clicking sounds
http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
Sad faced iPod, but my computer won’t recognize it
http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
Sad iPod solution
http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
Re: try to restore ipod and it says "can't mount ipod"
http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
iPod making clicking noise and is frozen
http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
Cant put it into disk mode
http://discussions.apple.com/thread.jspa?messageID=3786084#3786084
I think my iPod just died its final death
http://discussions.apple.com/thread.jspa?messageID=3813051
Apple logo & monochrome battery stay
http://discussions.apple.com/thread.jspa?messageID=3827167#3827167
My iPod ism’t resetting and isn’t being read by my computer
http://discussions.apple.com/thread.jspa?messageID=4489387#4489387
I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.
Finally, I read a fair comments from dwb, regarding of slapping the back of the iPod multiple times
Quote “This has been discussed numerous times as a 'fix'. It does work, at least for a while. In fact I remember using the same basic trick to revive Seagate and Quantam drives back in the mid to late 1980's. Why these tiny hard drives go bad I don't know - could be the actuator gets stuck in place or misaligned. Could be the platter gets stuck or the motor gets stuck. 'Stiction' was a problem for drives back in the 80's. Unfortunately the fix can cause damage to the platter so we temporarily fix one problem by creating another. But I know of two instances where a little slap onto the table revived the iPods and they are still worked a year or more later.”UnQuote

Error: The disc cannot be read from or written to. HELP!

We have two new Video iPods in the family... when we try to update them, we get the message: The disc cannot be read from or written to. We also cannot delete/edit the songs on the iPod. When we check certain songs to put on one iPod, but not the other, EVERY song is added -even with "only update checked files".
Is there away to create two Libraries -one for each iPod- and fix the Updateing problem? please!

Hi all,
I am sorry to report that I too have this same disc error problem when syncing my iPod to my iTunes library. I take no comfort in knowing that I am one of many that have this same error. I checked on the iPod lounge forum and I just couldn't count the number of users that had the same problem. There are just so many!
I too have tried "5 r's" and I have also tried using a few "s" words and others...lol.
It seems like there is no "fix" for this problem but I will say this: If there is no solution, then I will no longer be buying iPods. This is my third iPod that I have purchased. Which makes my Apple investment near the thousand dollar mark. That is way too much money spent to not have a functioning music player. I will be switching to another player to see if the grass is greener on the other side.
I have been most dissappointed with this error and I will not be "recycling" this iPod for ten percent off of my next iPod purchase.

Video files cannot be read in Adobe Presenter 10

Errors
When attempting to embed a video file (mp4 or WMV) with Adobe Presenter 10, the encode finishes (it doesn’t encode automatically, so it’s done manually), but an error displays (This file cannot be read), so the video is not displayed.
Also, when creating a quiz, none of the text, aside from radio buttons and the Send button can be edited, such as the answers to the quiz.
PC Environment
・windows7 professional 64Bit
Software
・Microsoft PowerPoint2010 32Bit
・Adobe Presenter10 32Bit
Question:
Is there a way to solve either problem or know the cause of the errors?
Thank you very much for your time.

Your experience is better, than mine. I look after a website for a Electronics Servicing organization. I've created many PDF using Acrobat 3 - 7.0.7 (the older versions on OS9. I use OSX.3.9 on a G4-500 using 1.5 Gb of System RAM. And I uses OSX.4.5 on a PowerBook 17" using 2 GB of system RAM. Since switch to Acrobat 6 and then 7 I've never been able to have anyone view a PDF created in 6 or 7 Format. The File appears to be there and the file fize indicates it has content. Whether viewing on a PC or a Mac. If viewed on a PC all that is seen is a Blank page with no text, and if it had a graphic no graphic is shown. If however; the person on the other end happens to have Acrobat or Reader 6 they can view the Acrobat 6 Files. And If they have 7 they can see the 6 and 7 files as well as anything below. However; most of the PC viewers I deal with still use Acrobat or Reader 5. Its these viewers I find that can't view the files. I've noticed also that when you do getinfo on a Acro/Reader, or 7 File created on my computer that in the thumbnail preview, all you see is the Acrobat A symbol, or a Blank thumbnail. Opening in 7 they can be viewed. Opening in 5 (I still have a OS9 Drive and e.5.0.5 installed) all I get is a Blank page no text and no Graphics if any in the content. SO every since 6 and 7 have come out I've had to save, then optimize for Acrobat 5 in order for my readers to see the pdf's.

Message "Do you mean to switch apps? Reader is trying to open Internet Explorer" in blue bar. Why

First time user. Instructions on how to use not clear. My problem is the message "Do you mean to switch apps? Reader is trying to open Internet Explorer?" suddenly appeared in blue bar. Occurs with I click on links in PDF. What caused this? How to fix? How to avoid it from happening again?
Same conflict with email links, just different message: "Do you mean to switch apps? Reader is trying to open mail?"
Goal: Do not want to switch apps and do not want to be asked this question.
Environment: Windows 8, file developed in Publisher 365, Reader 10 "I think"

Pat
Thank you for responding. I have recreated the error, but cannot figure out how to use Snipping Tool to get screenshot of a Windows 8 panel. Have the tool placed in the tool bar, but tool bar not accessible on the PDF display. Any suggestions?
Perk

PXI 2532, TB 2641 - Need information on interface board solutions

Hi. I'm working on a project where I am going to be using a PXI-2532 and a TB-2641 to set up an 8 x 64 switch matrix. I need an possible solutions for an interface board that will take the signals from the 3 ribbon cables from the TB-2641 and route them to either terminal blocks or some connector that I can then wire my measurment signals into. I was hoping to use a 90 pin femal Elco connector, but right now will look at any options. Please let me know of any interface board solutions that are out there for me to look at.
Thanks,
Doug

No problem Doug,
The SCB-264x is just listed as an accessory right underneath all of the terminal blocks and with the cable options. If you contact an NI sales representative when trying to configure a system, they will be able to help you pick all of the correct accessories you need.
I will also recommend you check out our tutorial How to Connect Signals to the PXI/PXIe-2532 that walks through all of the components you'll have and the steps necessary to connect them in your system.
Eric S.
AE Specialist | Global Support
National Instruments

ORA-00376: file 2 cannot be read at this time

Hi,
Our SAP system is down. When checked I found PSAPUNDO tablespace needs recovery. (From SYSSMU1$ to SYSSMU10$ NEEDS RECOVERY and SYSSMU11$ to SYSSMU17$ are offline).
So I have created another tablespace PSAPUNDO2 and altered the system.
SQL >create undo tablespace PSAPUNDO2 datafile 'D:\Oracle\SOL\sapdata1\undo_2\UNDO.DATA2' size 700MB;
SQL>alter system set undo_tablespace=PSAPUNDO2 scope=spfile;
I have changed undo_management to Manual. And I have not dropped old tablespace PSAPUNDO yet,
I have restarted the system and initially the database was not open.
I gave command alter database open and opened it.
The oracle has been started normally. But still SAP instance cannot be started.
Last few lines of aler log:
Sun Jan 06 04:05:12 2013
Completed: ALTER DATABASE OPEN
Sun Jan 06 04:06:08 2013
Shutting down archive processes
Sun Jan 06 04:06:13 2013
ARCH shutting down
ARC2: Archival stopped
Adjusting the default value of parameter parallel_max_servers
from 160 to 65 due to the value of parameter processes (80)
Sun Jan 06 04:06:29 2013
Starting ORACLE instance (normal)
Sun Jan 06 04:14:09 2013
Errors in file d:\oracle\sol\saptrace\background\sol_smon_3796.trc:
ORA-00604: error occurred at recursive SQL level 1
ORA-00376: file 2 cannot be read at this time
ORA-01110: data file 2: 'D:\ORACLE\SOL\SAPDATA1\UNDO_1\UNDO.DATA1'
Now when i give command:
show parameter undo, I got the table_space name as PSAPUNDO2.But if I give command
SQL> select segment_name,owner,tablespace_name,status from dba_rollback_segs;
I am getting PSAPUNDO as the tablespace insteadof PSAPUNDO2. PSAPUNDO tablespace needs recovery. (From SYSSMU1$ to SYSSMU10$ NEEDS RECOVERY and SYSSMU11$ to SYSSMU17$ are offline).
Also
In BRTOOLS, in show tablespace command I cannot see the new tablespace PSAPUNDO2.
Kindly suggest how to resolve this issue.

Hi,
Thanks for your reply. When I checked SAP down issue(around 6th Dec) I had exteneded the tablespace PSAPUNO and PSAPSR3 with brtools and restarted the server.
Then I checked further and found the problem was PSAPUNDO needs recovery.
Then I created another tablespace PSAPUNDO2 and altered system. (See my previous post).
Now as you told I checked alert log history to check when the problem started and found the following:
Incremental checkpoint up to RBA [0x2aad.15fb6.0], current log tail at RBA [0x2aad.15ff4.0]
Sun Dec 02 19:01:16 2012
Beginning log switch checkpoint up to RBA [0x2aae.2.10], SCN: 179359877
Thread 1 advanced to log sequence 10926
Current log# 2 seq# 10926 mem# 0: D:\ORACLE\SOL\ORIGLOGB\LOG_G12M1.DBF
Current log# 2 seq# 10926 mem# 1: C:\ORACLE\SOL\MIRRLOGB\LOG_G12M2.DBF
Sun Dec 02 19:06:21 2012
Completed checkpoint up to RBA [0x2aae.2.10], SCN: 179359877
Sun Dec 02 19:25:04 2012
Incremental checkpoint up to RBA [0x2aae.2d36.0], current log tail at RBA [0x2aae.2e11.0]
Sun Dec 02 19:30:00 2012
KCF: write/open error block=0x19 online=1
file=2 D:\ORACLE\SOL\SAPDATA1\UNDO_1\UNDO.DATA1
error=27072 txt: 'OSD-04008: WriteFile() failure, unable to write to file
O/S-Error: (OS 33) The process cannot access the file because another process has locked a portion of the file.'
Automatic datafile offline due to write error on
file 2: D:\ORACLE\SOL\SAPDATA1\UNDO_1\UNDO.DATA1
Sun Dec 02 19:30:01 2012
Errors in file d:\oracle\sol\saptrace\usertrace\sol_ora_5408.trc:
ORA-00376: file 2 cannot be read at this time
ORA-01110: data file 2: 'D:\ORACLE\SOL\SAPDATA1\UNDO_1\UNDO.DATA1'
ORA-00376: file 2 cannot be read at this time
I am not sure what caused this error: ORA-00376: file 2 cannot be read at this time
I think there is no issue with Parallel_Max_Server as I can see its entry in Alert log since 2007.
Thu Oct 25 20:48:48 2007
Adjusting the default value of parameter parallel_max_servers
from 160 to 65 due to the value of parameter processes (80)
Thu Oct 25 20:48:48 2007
Starting ORACLE instance (normal)
Will wait for your reply.
Edited by: 980149 on Jan 6, 2013 9:32 AM

Cannot download Reader 9.4

Hi
Just purchased a new HP 200-5120uk, with Windows 7 and Norton Internet Security
Cannot download reader 9.4 -download hangs at 31.7%
Tried switching off antivirus but no help
Any ideas?

Have you tried downloading the executable directly from:
http://ardownload.adobe.com/pub/adobe/reader/win/9.x/9.4.0/en_US/AdbeR dr940_en_US.exe

IVI-C driver for PXI-2532

Hi,
Does anyone know where I can find the IVI-C driver for the PXI-2532 card?
Thanks,
Isadore

Hi Isadore,
I'm providing another link to the latest NI-Switch driver version (NI-Switch 3.8) as of 9/12/08:
http://joule.ni.com/nidu/cds/view/p/id/1118/lang/en
Hope this helps!
Chad Erickson
Switches Product Support Engineer
NI - USA

"The iPad/iPhone cannot be synced because it cannot be read from or written to"

Since updating to iOS 7.0.2, when syncing my ipad and my iphone I get the message, "The ipad/phone cannot be synced because it cannot be read from or written to." When I deselect all photos from being synced to my devices, the message no longer appears. This tells me the problem is obviously related to iphoto. Reading a few forums on this matter tells me the solution has something to do with emptying a photo cache, deleting photos, then reimporting; everything is rather vague. I always empty trash in iphoto, then I secure empty trash in finder, then I erase free disc space in disc utility. What exact steps must I take so that itunes will once again sync all images from iphoto onto both my ipad and iphone?

For those that follow~
After speaking to Apple Support for about 2 hours, the issue has been narrowed down to a corruption problem in the computers iPhoto Library.
To confirm this:
Problem: When ticking "sync photos" in iTunes, your sync fails with the error "cannot be synced, unknown error -50". (syncing other data is OK, only when ticking photos is there a problem)
Test: HOLD alt/option (mac) & open iPhoto. You will be prompted to create a new Library. (the old one will be left untouched)
Import a few photos to your new library.
Quit iTUNES & re-open it. Connect your device & go to the photo tab. Click Sync Photos, you will see your new library. Sync - it should now work.
In iPhoto you can switch between your old & new Library using the FILE >Switch Library option.
Additionally: You may also import photos to your device by using iTunes "Sync Photos *From Folder* " option.
This is a work around to get your photos onto your device without using iPhoto.
This is not a fix, my issue is ongoing. I am posting only to help future readers. In my case rebuilding the iPhoto Library (hold option/alt when opening iPhoto) was not able to correct the problem.

PXI-2532 switch cannot be read in MAX

Similar Messages

Maybe you are looking for