PXI-8532 DNET card is not detected in MAX

Hi all,
I'm using NI PXI-1031(4 slot PXI chassis). I have the following cards in the respective slots
Slot 1= PXI-8106 Controller
Slot 2= PXI-6259 card(AI)
Slot 3= PXI-6509 card(DI,DO)
Slot 4= PXI-8532 Card(DNET)
In MAX(Measurement & Automation Explorer), I was expecting all the above cards(PXI 6259, 6509 & 8532) to be detected under Devices and Interfaces. But only the AI and DIO cards are detected in MAX under Remote Systems>>PXI>>Devices and Interfaces.
PXI-6259 (PXI1 Slot2)
PXI-6509 (PXI1 Slot3)
The device net card, PXI-8532 is not detected in MAX. Does MAX shows/detects the DNET card?
In MAX, I selected Tools menu>>NI-DNET>>RT Hardware Configurations. Then a window prompts for RT IP address. After entering the IP address, I pressed OK. A message appears that no device is found.
Can any one help me how to detect the DNET card in MAX and do the DNET port configuration?
DNET driver version - 1.6.4
Thanks,
Raja
Solved!
Go to Solution.

Dirk,
Thanks for the reply. After updating the new driver, I am able to detect the DNET card PXI-8532 in MAX
New driver - NI-Industrial Communications for DeviceNet 2.1
But Im not able to configure the Device Net port. In MAX, I selected the menu option Tools>>NI-DNET>>RT Hardware Configurations. Then a window prompts for RT IP address. After entering the IP address, a message appears that no device interface is found.
By default, the DNET0 port is configured for the card in MAX. So I tried to communicate from LabVIEW using DNET0 port.
After installing Devicenet 2.1, an additional function palette has been added for DNET in LabVIEW.
Old DNET function palette - Instrument IO>>DNET
New DNET function palette - Industrial Communications
My original application was written with old function palette VIs which corresponds to DNET 1.6.4 version. In the download link that you shared has a description about the driver compatibility. The description says still the DNET card PXI-8532 is compatible with NI-DNET 1.x LabVIEW VIs.
With the old DNET VIs, I tried to establish communication with DNET interface port "DNET0". But it shows error while opening the interface.
Error Code ="-1074388957" - The Interface is invalid or unknown. Solution: Verify that the interface is assigned to a specific port within the Devices and Interfaces branch of the Measurement and Automation Explorer (MAX).
With the new DNET VIs(DNET 2.1.0), Im able to open the DNET interface successfully. But my original application was written in Old DNET VIs (DNET 1.6.4).
1. Do you know why the DNET 1.6.4 LabVIEW VIs are not working with PXI-8532 DNET card?
2. Can you help me how to configure DNET port in MAX for PXI-8532 DNET card?
Thanks,
Raja
LV 2009, Windows XP

Similar Messages

My sim card is not detected...

What can I do? I check it in other phone and it's OK. By my iPhone all the time said: Your sim card is not detected.

But I was done with my iPhone everything.
Have no idea what this means.
In your opinion it is a problem with hardware? Maybe.. But what I can do in this situation?
Copied from my previous post.
If OK in another cell phone and usable to place and receive calls, etc. with another phone, there is obviously a problem with your iPhone. This may be a hardware problem with the interior of the iPhone where the SIM card makes the connection with the iPhone, or it could be a software problem.
If no change after powering your iPhone off and on and/or after a reset, try restoring your iPhone with iTunes as a new iPhone or not from your iPhone's backup. If no change after this, your iPhone has a hardware problem.

Sim card was not detect after upgrade my iphone4s to ios 6.0.1

my sim card was not detected after i update to ios 6.0.1
i had ald try many time plug in n out my sim card it keep on show searching no service or no sim
i had reset my network setting n i reset all n now i cant activate my iphone

Connect your iPad to iTune (computer) and Check for Updates. Backup before you proceed with update.
http://i1224.photobucket.com/albums/ee374/Diavonex/Album%201/e0f22e92de98ebae10e 3fd537c16619e.jpg

Sound card is not detected under Windows 8

Hi there,
I bought an Asus Xonar DGX PCIe soundcard. When inserted it is not detected by the system; it is like it doen not exist.
I have a new Dell Inspiron 660 pc with 3mHz I5 processor, 8Gb memory, 4 extension slots, one full lengthand 3 PCIe, Nvidia Gforce GT640 graphics card (in the full length extension slot). Its running Windows8. The Xonar is inserted in the 3rd slot as the
second is blocked by the vent of the Gforce card.
I loaded the latest driver form Asus and disabled the on-board soundcard in the "Bios" but to no avail.
The first card was returned to the distributor with those problems as they expected it to be defect. Now i got a new one and installed it has the same problem.
Can anybody help me with this one??
Regards Steffen

Hi,
Please try the following:
1. Check if the card can work on other Windows 8 computers.
2. Update chipset driver and BIOS.
As this is a hardware issue, it is also recommended that you contact Asus and Dell for help.
Thanks.
Nicholas Li
TechNet Community Support

MOVED: Nvidia graphics card was not detected in your system

This topic has been moved to MSI Notebooks & Netbooks.
https://forum-en.msi.com/index.php?topic=178616.0

^^Gecko, I'm not bustin' on you, but you're wrong. Or, you are, but I doubt it, one of the lucky ones.
I've gotten 3.1 installed by running the setup .exe file from the DVD via Windows Explorer. Everything seems OK except the graphics/resolution. My NVIDIA card isn't recognized and my resolution options only go up to 1280 x 800.
The Window 7 Performance Information and Tools shows this:
"Graphics
Total available graphics memory Not detected
Dedicated graphics memory 0 MB
Dedicated system memory 0 MB
Shared system memory 0 MB
Display adapter driver version 6.1.7600.16385
Primary monitor resolution 1280x800
DirectX version DirectX 8 or earlier"
Apple, please, help us!
Message was edited by: K Dubb
Message was edited by: K Dubb

Suddenly my phone's microSD card is not detected

I have a Nokia 6300 which i have been using for more than a year. Suddenly last week my phone stopped detecting the microSD card (128 mb) which came along with phone. I tried taking out & re-inserting but it didnt help. I have also tried accessing it through Nokia Browser through my laptop but that has also not helped... I tried inserting in another phone but there also it is not detecting.
Is it a virus attack? How can I make my phone detect the card?
PLzzzzzzzzzz help me out. I have some important pics that I would miss out......

It's certainly not a virus.
It sounds like your card has become damaged or corrupted.
Your only option for recovering data from this card is to use it in a card reader with a PC along with data recovery software.
You can find plenty of free recover software by searching google.
If the PC manages to read the card without any special software then it may be a hardware issue with the card reader in the phone.

Z60m card reader not detecting cards

Hi,
I had my z60m formatted recently and since then the card reader does not detect cards. On searching online I found a ricoh card reader driver which claims to work for the z60m which I have now installed. Still no luck. The green light next to the card reader blinks when I put a card in which could mean the hardware works.
Hope someone can help me.
Thanks
Riaz

hi
drivers for card reader for z61m - win7 :
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=32...
they are HP but working just fine (mass controller question mark in DM)

New airport extreme card is not detected

I brought a new airport extreme card and installed as instructed but my computer is not detecting it at all. Im new to using a Mac, so please can someone let me know what I'm doing wrong? If you need more info please ask.
emac Mac OS X (10.3.9)

this is definately the correct card...
How do you know? To identify which eMac you have, you can use KB 86325, eMac: How to locate the serial number and identify your model. Then you will be able to determine if you need the AirPort card or AirPort Extreme card.
What kind of keyboard are you using?
The command key probably has an Apple symbol.
Here are some other symbols for those keys:

Ethernet card was not detecting...

I am using Dell Laptop, I have a inbuild NIC card. It is working fine in my Windows OS. But it was not detecting in OEL 5.5
I have a ADSL Modem and want to connect to Internet in OEL 5.5
Is it possible to use WiFi in OEL 5.5 ???
Anyway, I want to use Internet on my OEL 5.5 laptop

Karumudi7 wrote:
So, you are preferring Ubuntu. I have Ubuntu 10.04 Desktop edition CD, can I go with this?
Are the things are same like the OEL? Most things, yes.
Becoz there is no root in Ubuntu directly and the command is also different $su -iThere is - simply the security model is a tad different as a desktop o/s does not have a sysadmin dude, whereas a sever o/s does have.
To access root on Ubuntu, simply use:
sudo su - root
Type your password when prompted.
Or install Open SSH Server and you can ssh (from other platforms too) into your desktop - including as root. E.g.
sudo apt-get install openssh-server
What abt bash_profile?The same. Bash is bash is bash - irrespective of the distro.
If the things are same as in the OEL for Oracle 10g manual Database Installation, I can prefer that.Well, there's very little that is "special" with an Oracle s/w installation. It is a bunch of popup windows with a next and cancel button - all you need to do is read the text and change the defaults if needed. Anybody can install Oracle software. And how often do you install Oracle s/w? Definitely not every second day.
The important bit is not the installation itself - but how you administer the database.
Finally, wat abt Kernel Parameters, Will the parameters are same for all Distros?Mostly. Cannot speak for all distros, but the ones I've worked with use the sysctl command to set kernel parameters. As distros are based on a specific Open Source/GPL Linux kernel, those kernel parameters are the same. sysctl uses the config file +/etc/sysctl.conf+ - so that will also be the same across distros.
A distro does not mean something radically different. Underneath it all, it is the same source code. The differences come with what that kernel ships. What drivers are bundled? What Window manager? What versions used (stable, experimental, etc). What software packages are included.
If you are going to use Ubuntu, then I suggest installing XE. It is free. It is great for experimenting. You can create database instances. You can destroy them. You can use rman for backup and recovery. You can write your own database create scripts. You can sudo as the oracle o/s user, manage and monitor and kill processes. Etc.

Pxi not detected under max

Hi...
I have aPXI 1000B chassis with 8156B controller, i am trying to make the pxi get detected under MAX for 1 month now... still no result... i don know what the problem is...

i am using windows xp. the labview version is 7.1 with a 7.1 real time. the max version is 3.3 and the controller is 8156B with 1000B chassis. the pxi doesnot boot into anything, but when i connect a vga port the boot screen look like the one in photo i have attached.
Attachments:
8156B controller.jpg ‏319 KB
pxi boots to this screen.jpg ‏311 KB

HBA Card is not detecting in m4000 server

Hi,
hba is not detecting in M 4000 server. Any one plz help me.
Thanks & Regards,
Venkata Siva

Hi.
You not write what type/vendor new HBA.
You not write what you do for detect new HBA and what means new HBA not detected.
I hope you create */reconfigure* before install new HBA or make boot -r
Regards.

CRIO not Detected in MAX

Hello,
I'm totally new to NI and LabVIEW, so I may have done many unnecessary steps or missed something obvious, but here's the rundown (what I can remember) of what I tried:
I'm trying to make a cRIO-9073 (newer revision, IPreset switch does not reset IP to 0.0.0.0) work with LabVIEW 2011 SP1 (includes MAX 5.1.0f0 and NI-VISA 5.1) installed on Windows 7 Professional SP1 using a crossover ethernet cable. MAX does not recognize the cRIO in the Remote Systems tab. After initial problems, I was able to locate 2 IP addresses corresponding to the cRIO, but its still does not appear in MAX. I have tried the following:
refreshing the list using F5, rebooting the cRIO, and using the IPreset switch
reinstalling drivers on the computer using September 2011 NI System Driver Set CD
manually adding the a new remote VISA system in MAX (tells me that a device is already using that IP address)
manually adjusted the LAN settings in the Windows control panel and disabled DHCP
edited Internet Protocol Version 4 (TCP/IPv4)
manually set IP address and local subnet mask to match the cRIO settings
Added exceptions to the Windows firewall
NI-RIO RPC Server
VISA Interactive Control
I think that the software and/or drivers on either the computer or the cRIO may not be up to date or compatible with the rest, but I'm not too sure on how to install software on the cRIO if I cannot see it in MAX. Any ideas?
Thank you!
Solved!
Go to Solution.

Zach-H wrote:
To add the device manually you need to select "Remote Device (not on the local subnet)" not "Remote VISA System". The cRIO should try and default to a link local IP address (169.254.x.x Range) if it can't communicate with a DHCP server. This will likely be the case with the cRIO connected directly to the computer.
If your computer isn't on an agreeing IP and subnet mask its likely that the cRIO wouldn't show up unless you add it manually. You don't want to set them up as the same as the cRIO as they need individual IP addresses. I would recommend setting the subnet masks the same and adding one to the last number of the cRIO's IP address, which should allow it to show up in MAX.
Very useful document for this kind of a situation: http://digital.ni.com/public.nsf/allkb/abe4bc247e8ac9bc8625734e005cab42?OpenDocument
When I tried to add it as a "Remote Device (not on the local subnet)," I got the error message "The device at this address is not supported by the drivers installed on this host." I checked that my version of NI-RIO 4.0 is compatible with the cRIO-9073.
Also, I ran through the link you provided, and the steps did not remedy the problem. When I ran the cRIO with the CONSOLE OUT switch ON, I was able to get lots of information from the cRIO in the command prompt in Windows. This makes me think that there are no problems with the cRIO, but with the software I have installed on Windows. I'm not sure what else I can try to install, though.

EHWIC Card is not detecting when we put in the router

Hello Guys,
Currently my router doesn't detects the ehwic card and its currently working on hwic.
I just need to confirm if ehwic card supports T series IOS .
as per the below Cisco document it support min IOS 15.1.M series & I'm using 154-1.T1
appreciate if somebody can quickly confirm the same
http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/high-speed-wan-interface-cards/qa_c67-660125.html
http://www.cisco.com/c/en/us/td/docs/routers/access/interfaces/software/feature/guide/EHWIC_1_GE_SFP_CU_FM.html#wp1069000
please find my current IOS version & card type
Card is : EHWIC-1GE-SFP-CUV01
#Show version
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.4(1)T1, REL
EASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Wed 12-Feb-14 04:27 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)
Router uptime is 2 weeks, 3 days, 11 hours, 54 minutes
System returned to ROM by power-on
System image file is "flash0:c1900-universalk9-mz.SPA.154-1.T1.bin"
Last reload type: Normal Reload
Last reload reason: power-on
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.
2 FastEthernet interfaces
2 Gigabit Ethernet interfaces
1 terminal line
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)

Got the things from one test router having different image .please find below.,
#sho version
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.0(1)M1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 02-Dec-09 14:14 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M3, RELEASE SOFTWARE (fc1)
uptime is 50 minutes
System returned to ROM by power-on
System image file is "flash0:c1900-universalk9-mz.SPA.150-1.M1.bin"
    ##### sh diag
Slot 0:
C1941 Mother board 2GE, integrated VPN and 2W Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 00:50:40 ago
EEPROM contents at hardware discovery:
PCB Serial Number        :
Hardware Revision        : 1.0
Part Number              :
Top Assy. Part Number    : 800-30798-01
Board Revision           : B0
Deviation Number         : 0
Fab Version              : 03
Product (FRU) Number     : CISCO1941/K9
Version Identifier       : V01
CLEI Code                :
Processor type           : C8
Chassis Serial Number    :
Chassis MAC Address      :
MAC Address block size   : 96
Manufacturing Test Data : 00 00 00 00 00 00 00 00
EEPROM format version 4
EEPROM contents (hex):
WIC Slot 0:
-       Unknown WAN daughter card
        WIC module not supported/disabled in this slot
        PCB Serial Number        :
      Hardware Revision        : 1.0
       Part Number              :
       Board Revision           : A1
Top Assy. Part Number    : 800-34350-01
Deviation Number         : 0
Fab Version              : 05
RMA Test History         : 00
RMA Number               : 0-0-0-0
RMA History              : 00
Product (FRU) Number     : EHWIC-1GE-SFP-CU
Version Identifier       : V01
CLEI Code                :
Unknown Field (type 00D4): CC
Asset Identifier         : A0
EEPROM format version 4
EEPROM contents (hex):
===
show inventory
NAME: "CISCO1941/K9 chassis", DESCR: "CISCO1941/K9 chassis"
PID: CISCO1941/K9      , VID: V01 , SN: ######

Lenovo y510p - Intel card is not detected

Hello,
Recently I bought Lenovo y510p laptop in that configuration:
Lenovo Y510p
Intel Core i7 4700MQ
RAM 8 GB ( 1 x 8 GB ) 1600 MHz / PC3-12800
1TB HDD, 8gb SSD
NVIDIAGeForce GT 755M
After some problems I installed Arch on it. I had problems with black screen on start. After all I wanted to install drivers for Nvidia Optimus. But when I typed `lspci` I got that response:
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06)
00:01.1 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x8 Controller (rev 06)
00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05)
00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05)
00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05)
00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #4 (rev d5)
00:1c.4 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #5 (rev d5)
00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05)
00:1f.0 ISA bridge: Intel Corporation HM86 Express LPC Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05)
00:1f.3 SMoBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05)
01:00.0 VGA compatible controller: NVIDIA Corporation GK107M [GeForce GT 755M] (rev a1)
01:00.1 Audio device: NVIDIA Corporation GK107 HDMI Audio Controller (rev a1)
07:00.0 3D controller: NVIDIA Corporation GK107M [GeForce GT 755M] (rev a1)
08:00.0 Ethernet controller: Qualcomm Atheros QCA8171 Gigabit Ethernet (rev 10)
09:00.0 Network controller: Intel Corporation Centrino Wireless-N 2230 (rev c4)
First thing I noticed is that my CPU is detected as Xeon, not i7 and there is no line with Intel VGA. But in /proc/cpuinfo` this CPU is detected as i7:
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 60
model name : Intel(R) Core(TM) i7-4700MQ CPU @ 2.40GHz
stepping : 3
microcode : 0x12
cpu MHz : 2921.156
cache size : 6144 KB
physical id : 0
siblings : 8
core id : 0
cpu cores : 4
apicid : 0
initial apicid : 0
fpu : yes
fpu_exception : yes
cpuid level : 13
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx pdpe1gb rdtscp lm constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf eagerfpu pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 fma cx16 xtpr pdcm pcid sse4_1 sse4_2 movbe popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm abm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid fsgsbase tsc_adjust bmi1 avx2 smep bmi2 erms invpcid
bogomips : 4791.76
clflush size : 64
cache_alignment : 64
address sizes : 39 bits physical, 48 bits virtual
power management:
// and rest till 7th proessor
Thanks for all answers.
Last edited by grzlus (2014-08-29 16:34:55)

You mean you don't have a Nvidia card in the UltraBay? And Windows shows 2 Nvidia GPUs and Intel GPU at the same time?
Have you checked BIOS/UEFI settings? From what I read, this thing has a hardware mux, so even with just one Nvidia GPU it's possible to switch between Intel/Nvidia/Optimus. But I couldn't tell if this can be done in BIOS/UEFI or if it requires some more magic that's done from Windows.

PCMCIA Wlan card is not detected: Error 1058: service cannot be started

PLEASE HELP!
I am running WXP Pro for over 2 years and I have been connecting to the internet via a wireless pc card in my laptops PCMCIA slot with no problems. Suddenly last week it started to randomly disconnect and reconnect, and now it has gone off completely.
I bought a new WiFi card and still didn't work. I have checked the device manager and the PCMCIA cardbus driver is working fine as is every other device. The wireless card driver and some other network related drivers fail to start no matter what I try and how many times I try. I have tried another laptop and both my old card and the new one work fine.
All the device driver that I try to start have the error
"Error 1058: The service cannot be started, either because it is disabled or because it has no enabled devices associated with it."
The card driver is installed, just not starting, it's like the laptop cannot detect or see the card in the slot
Please help; I am having trouble finding anyone with the same problem after a week of searching the web.

Hi
This behavior can occur if the service is disabled or if the service is disabled for the hardware profile that you are currently using.
To enable the service do this:
1. Click Start, point to Programs, point to Administrative Tools, and then click Services.
2. Double-click the service that did not start.
3. Click the Log On tab.
4. Verify that the service has not been disabled for the hardware profile that you are using. If it has, click Enable.
5. Click the General tab. Verify that the service has not been disabled in the Startup Type box. If it has, click Automatic to have it start when you start the computer.
This was described here in the MS knowledge base article
http://support.microsoft.com/kb/241584

PXI-8532 DNET card is not detected in MAX

Similar Messages

Maybe you are looking for