PXIe-1062Q Power switch will not turn of chassis

I have a PXIe-1062Q PXI Chassis that I can turn on with the front mounted power switch, but it won't turn off again.  Is there something wrong with it, or am I missing something in the way that it's set up?
Solved!
Go to Solution.

Never mind.  Figured it out.  I need to press the power button for several seconds and then it turns off.

Similar Messages

  • PXIe-1075 Power switch will not turn off chassis

    Hi,
    I think I am having trouble turning my PXIe-1075 chassis off with the front mounted power switch. When I press the power switch, the green LED will ficker and the PWR LED on my PXIe-8360 MXI card will flicker from green to red and then back to green. I have a PXI-1042 chassis as well that seems to turn off properly. The switch on my PXI-1042 chassis has two positions, but the switch on my PXIe-1075 only seems to have one position. I am in a spot where I will need to power off my chassis to move it occasionally. Does it sound like my PXIe-1075 chassis has an issue? Am I missing something? I also tried holding the power switch. This will cause all the installed modules active light to turn off, but the PWR light on the switch and the PWR light on the MIX card will stay the same.

    Hello,
    The 1075 has two modes for shutdown.  You can select between the modes with the 'inhibit' switch on the back of the chassis.  When this switch is in the default position, the chassis will power down when you shut down the controller in the chassis (I'm not sure if it will automatically power down with the MXI connection when you shutdown the PC- I do not believe it will).  When the switch is in the manual position, the chassis does not shut down with the controller and you must use the Inhibit signal on pin 5 of the Remote Inhibit and Voltage Monitoring connector.  I believe your chassis is in 'Manual' mode.  More information on this is available in the manual on page 2-12:
    http://www.ni.com/pdf/manuals/372537b.pdf
    I do not think that the power button on the front can be used to power off the chassis.
    Jon F.
    Applications Engineer
    National Instruments

  • My nano 6th generation power button will not turn off

    My Nano power button will not turn my I pod off anymore.  It'a 6th generation.

    You can either do an out-of-warranty replacement at your nearest Apple Store for $65/$75 USD depending on the size of your Nano or have a 3rd party replacement of the switch.

  • My power cord will not turn green, what can I do

    My power cord will not turn green after preforming an update, what can I do

    http://support.apple.com/kb/TS1713

  • HT1320 my ipod nano is stuck in the lock position, my  hold switch will not turn off even when I move it, I have restored it and it came back on in the hold position

    My ipod naaIno is stuck in the lock position, my hold switch will not turn off even when I move it.  I have tried restoring it and resetting it and it still comes back on in the hold/locked postion.  It will only play when placed on a docking station and then I cant scroll to pick songs, I can only go to next song using buttons on docking station.

    You will need to have the hold switch replaced.

  • Limit switchs will not turn off

    We are using PXI 1031 with NI Motion Assistant and the Measurement and Automation Explorer. Our limit switchs are always reading active, and when we go into Axis Configuration to try and change thigns, something is creating an update loop that prevents us from changing any of the default confiurations. Any suggestions on either the update problem or the limit switch issues? Probing the limit switches shows good performance 0V-4.8V off/on, so it is not the hardware.
    Thanks,
    Aaron
    Solved!
    Go to Solution.

    What is the motion controller that you are using?
    We can try to go into Measurement and Automation Explorer, expand your particular motion device, go to Motion I/O Settings and disable all limit swithces and initialize to see if the limit switch will be turned off.
    Andy Chang
    National Instruments
    LabVIEW Control Design and Simulation

  • The power button will not turn on the computer.

    My Mac book pro screen is black and the power button will not start the computer.

    Try checking thru here.
    http://support.apple.com/kb/TS1367

  • My ipod touch 3g displays logo and low power but will not turn on

    My Ipod 3g displays the apple logo and the low battery screen but it will not turn on.
    Help please?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar
    Also maybe here:
    See:
    iPod touch: Hardware troubleshooting
    - Try another cable
    - Try another charging source
    - Look at the dock connector on the iPod. Look for abnormalities like bent or corroded contacts, cracked or broken plastic.
    - Make an appointment at the Genus Bar of an Apple store.
    Apple Retail Store - Genius Bar

  • IBook G3 800 GHz will work on battery power but will not turn on with AC pl

    This iBook will function with a battery, but when the AC is plugged in it does nothing. It will not turn on. Is this a logic board problem or maybe a short or something not connected inside for the AC plug?

    It's a rather complicated repair:
    http://www.ifixit.com/Guide/Repair/iBook-G3-12-Inch-DC-In-Board/134/1
    Apple doesn't consider it a do-it-yourself job.
    Expect to pay $115-$145 for the repair (plus shipping if you have to send it away). The iBook may not be worth the repair, so some people are trying to do it themselves.

  • G5 Power Mac will not turn on.

    I have a G5 dual 1.8, one of the earlier models, and I'm guessing the ram restart thing will not work on it. I was just using Safari, and the computer completely shut down, since then, I have not been able to turn it back on, I've tried using a different power cord, and I'm wondering if replacing the power supply will be my best bet.
    Message was edited by: Brian Hoisington

    Hi, and a Warm Welcome to Apple Discussions and the Power Mac G5 Forum!
    Well - if you have checked that the mains power right up to the G5 is definitely good (and have waggled the plug in the socket at the back of the G5, for good luck) - you could try resetting the PMU/SMU
    http://docs.info.apple.com/article.html?artnum=300341
    but, if you do not get a 'relay-click' from the PSU, low-down at the back of the G5, when you first connect the mains power, it probably won't help.
    There is a rather gloomy symptom chart (at page 104 in Preview) here - and also instructions.
    If you wish to take a gamble on it being the PSU that's the cause, they may be available here
    http://www.dvwarehouse.com/G5-Power-Supply-c-253247541.html&pltid=723fda346ab59730cfb5d40ab2fecc68
    http://www.mac-pro.com/Mac-Pro-Online-Store/PowerMacs-Intel-MacPro-Towers
    http://www.welovemacs.com/g5serviceparts.html
    and elsewhere.
    Please post again if you have any questions. Good Luck.

  • HT1688 wi fi switch will not turn on

    My iPhone 4s would not allow wi fi to turn on, after trouble shooting with tech support, I ws told it was hardware issue, so went and got a replacement at the Appple store, the guy turned it on and wi fi was searching in store, as I walked out of store (still in Mall) it went off and now wont come back on, I updated the phone and tried to do a restore and nothing will bring wi fi.  Any one else have this issue? 

    Hello Lee Ann,
    You may need to reset your phone's network settings.
    iOS: Wi-Fi settings grayed out or dim
    http://support.apple.com/kb/TS1559
    Cheers,
    Allen

  • T60 beeps four times after pushing power button; will not turn on.

    After returning from a flight yesterday, I tried to start up my T60.  After pressing the power button, all the usual status lights came on.  Shortly thereafter it beeped at me four times, approximately four seconds after pushing the power key.  It then stops doing anything at all.  The power and battery lights remain on.  Pushing the power key again tuns off the power and battery lights.  The screen never comes on.  I have checked the RAM (it is secure) and have tried booting on A/C w. no battery, A/C w. battery, and on battery alone.  Any help would be greatly appreciated.  Thanks in advance.
    Solved!
    Go to Solution.

    Hello,
    According to this document on Lenovo's web site, Beep and no beep symptoms - ThinkPad General, there may be an issue with the TPM (security) chip.  Have you been able to resolve the issue yet?
    Regards,
    Aryeh Goretsky
    I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
    S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
      Deutsche Community   Comunidad en Español Русскоязычное Сообщество

  • My iPhone has switched off and will not turn back on

    mmy iPhone 5c was working perfectly fine this morning whilst I have been in work. But when I left work and checked my phone in my pocket it had switched itself off and will not turn itself back on. I have tried to plug into charger but still not turning on

    Hi Kate,
    It must be very frustrating to be unable to use your iPhone since it won't even power on. Let's see if we can get things back up and running.
    I would suggest that you troubleshoot using the steps in this article - 
    If your iPhone, iPad, or iPod touch doesn't respond or doesn't turn on - Apple Support
    Start with the section titled If your device still won't turn on or start up.
    Thanks for using Apple Support Communities.
    Sincerely,
    Brett L 

  • My Ipad2 just shuts down and will not turn on. Rebooting does not help. He switched on when I start charging it. In this case, the battery is charged.

    My Ipad2 just shuts down and will not turn on. Rebooting does not help. He switched on when I start charging it. In this case, the battery is charged.

    Standard troubleshooting steps in the following order:
    1. Reset: Press the sleep/wake button & home button at the same time, keep pressing until you see the apple logo, then release. Ignore the slide to power off.
    If no change, continue:
    2. Restore your phone from a backup, note: if the problem is related to corrupt data, while this will restore a fresh OS, it will also restore the problem.
    If no change, continue:
    3. Restore as a "new" phone in itunes & re-sync your content. All saved data will be lost.
    If no change, make an appointment at an Apple store.

  • My ipad will not turn on/charge, itunes will not recognize ipad, has been charging for hours power and sleep button did not work

    My ipad will not turn on/charge. has been charging for hours. Itunes will not recognize it and i have tried the power/sleep button as well. PLEASE HELP!

    Please tell me that it has NEVER been jailbroke.  If it hasn't been, here are some standard repair procedures:
    First, try a system reset.  It cures many ills and it's quick, easy and harmless...
    Hold down the on/off switch and the Home button simultaneously until you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.
    If the Reset doesn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  It could take well over an hour!  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow the on-screen directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."
    At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod.  As before, say "yes."  Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time.  If that happens, only the apps that are part of the IOS will appear on your device.  Corrective action is simple -  choose manual "Sync" from the bottom right of iTunes.
    If you're unable to do the Restore (or it doesn't help), go into Recovery Mode per the instructions here.  You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again.  Also, if you have IOS-7, read this.

Maybe you are looking for