PXIe-1075 Power switch will not turn off chassis

Hi,
I think I am having trouble turning my PXIe-1075 chassis off with the front mounted power switch. When I press the power switch, the green LED will ficker and the PWR LED on my PXIe-8360 MXI card will flicker from green to red and then back to green. I have a PXI-1042 chassis as well that seems to turn off properly. The switch on my PXI-1042 chassis has two positions, but the switch on my PXIe-1075 only seems to have one position. I am in a spot where I will need to power off my chassis to move it occasionally. Does it sound like my PXIe-1075 chassis has an issue? Am I missing something? I also tried holding the power switch. This will cause all the installed modules active light to turn off, but the PWR light on the switch and the PWR light on the MIX card will stay the same.

Hello,
The 1075 has two modes for shutdown.  You can select between the modes with the 'inhibit' switch on the back of the chassis.  When this switch is in the default position, the chassis will power down when you shut down the controller in the chassis (I'm not sure if it will automatically power down with the MXI connection when you shutdown the PC- I do not believe it will).  When the switch is in the manual position, the chassis does not shut down with the controller and you must use the Inhibit signal on pin 5 of the Remote Inhibit and Voltage Monitoring connector.  I believe your chassis is in 'Manual' mode.  More information on this is available in the manual on page 2-12:
http://www.ni.com/pdf/manuals/372537b.pdf
I do not think that the power button on the front can be used to power off the chassis.
Jon F.
Applications Engineer
National Instruments

Similar Messages

  • PXIe-1062Q Power switch will not turn of chassis

    I have a PXIe-1062Q PXI Chassis that I can turn on with the front mounted power switch, but it won't turn off again.  Is there something wrong with it, or am I missing something in the way that it's set up?
    Solved!
    Go to Solution.

    Never mind.  Figured it out.  I need to press the power button for several seconds and then it turns off.

  • HT1320 my ipod nano is stuck in the lock position, my  hold switch will not turn off even when I move it, I have restored it and it came back on in the hold position

    My ipod naaIno is stuck in the lock position, my hold switch will not turn off even when I move it.  I have tried restoring it and resetting it and it still comes back on in the hold/locked postion.  It will only play when placed on a docking station and then I cant scroll to pick songs, I can only go to next song using buttons on docking station.

    You will need to have the hold switch replaced.

  • My nano 6th generation power button will not turn off

    My Nano power button will not turn my I pod off anymore.  It'a 6th generation.

    You can either do an out-of-warranty replacement at your nearest Apple Store for $65/$75 USD depending on the size of your Nano or have a 3rd party replacement of the switch.

  • Limit switchs will not turn off

    We are using PXI 1031 with NI Motion Assistant and the Measurement and Automation Explorer. Our limit switchs are always reading active, and when we go into Axis Configuration to try and change thigns, something is creating an update loop that prevents us from changing any of the default confiurations. Any suggestions on either the update problem or the limit switch issues? Probing the limit switches shows good performance 0V-4.8V off/on, so it is not the hardware.
    Thanks,
    Aaron
    Solved!
    Go to Solution.

    What is the motion controller that you are using?
    We can try to go into Measurement and Automation Explorer, expand your particular motion device, go to Motion I/O Settings and disable all limit swithces and initialize to see if the limit switch will be turned off.
    Andy Chang
    National Instruments
    LabVIEW Control Design and Simulation

  • MSI z77A-G43 - After Shutdown - Fans will not turn off

    Just installed a new MSI Z77A-G43 Motherboard for my husband since his old motherboard died. The one thing I've noticed though is that the fans will not turn off after I do a shutdown and I'd have to do a manual shut down instead. Any ideas what could be happening? Also it will randomly restart when not shutdown completely with the fans still on.
    Here are the specs of the PC.
    MOBO: Z77A-G43
    Processor: Intel i5 - 2500k Quad Core
    Video Card: Geforce - GT 610
    Ram: 8 Gigs
    Hard Drive - 128gb ssd and 1.5 tb hdd
    It's really barebones since I'm trying to just get it to run then get it back to normal working order with the next pay check
    EDIT!!!!::
    Forgot OS is Window 7 Ultimate X64

    If you are sure that your CPU is seated properly and that the PWM fan connector is seated correctly, then you may want to test with another known working PSU. I am not saying that your PSU is faulty, but before exhanging the board, I would definitely test that as well.
    EDIT: Just a question, did you disconnect the power switch and the other front panel connectors of your case and started the PC by shorting the Power switch [pins 6 and 8 on JFP 1]with a screw driver tip ? The remote possibility exits that the cables may have been connected incorrectly or may have a short.

  • My iPhone is fully charged and just gives me a blank screen and will not turn off, what do I do?

    my iPhone is fully charged and just gives me a blank screen and will not turn off, what do I do?

    Reset the phone like the manual says:  hold the on/off switch and the home button simultaneously until the Apple logo appears.  May take up to 30 sec

  • HT200197 My Apple TV just has a white blinking light.  Will not turn off.  The TV shows nothing but the Apple logo.  It worked fine yesterday.  PS - I am not an IT person.  :)

    My Apple TV just has a white blinking light.  Will not turn off.  The TV shows nothing but the Apple logo.  It worked fine yesterday.  PS - I am not an IT person. 

    pull the plug for 30sec and try reconnecting power
    if that don't help
    Apple TV (2nd and 3rd generation): Restoring your Apple TV - Apple Support

  • The light on the back of my phone will not turn off, even when I turn the phone off. Help?

    The light on the back of my iphone 4s will not turn off. Even when I turn the phone off the light stays on.  Can someone help? I did notice that the camera on the back has a little bit of moisture. (I have 3 small kids).

    You will need to have the hold switch replaced.

  • When charged up I touch will not turn off with on off button

    When charged up my I touch will not turn off using the on/off button,can use the home button but I touch stays on & drains the battery.

    To turn the the iPod off you have to press and hold the On/Off button until the power off slider appears (about 5 seconds). Are you doing that?

  • My 1st generation iPad will not turn off and I have performed the suggested fix. What's next?

    My iPad will not turn off. I have done the off/sleep key home button procedure.

    Just to be perfectly clear, when you reset the iPad by hod,ing down on the sleep and home buttons at the same time for about 10 seconds until the Apple logo appears on the screen, that is a way of resetting the system and restrating the device. If you want to shut down, you still have to hold down on the power button until the slider appears and then slide to the right to shut the iPad off.
    IS this what you are doing and if so what happens when you try to shut down? Describe what happens in detail.

  • My shuffle will not turn off

    I purchased a shuffle this past August and have had no issue with it. I went on vacation and it did not get used for a week. I then synced up and let it charge, went on my daily run. When I tried to turn it off, the songs kept playing. The unit will play until the battery is dead and will not turn off.
    Any suggetions?

    If it really is a 1st Gen shuffle the switch sometimes breaks or gets crud in it preventing contact in some of its positions... The slide can be removed and contact cleaner can be sprayed inside.
    http://www.ifixit.com/Guide/iPod/iPod-Shuffle/Hold-Switch/98/1/Page-1

  • IPhone 4 is stuck in the telephone screen, will not turn off by holding down top button or main menu

    iPhone 4 is stuck in the telephone screen, will not turn off by holding down top button or main menu, can't send texts, emails, check internet etc.,

    Hold down the home and power buttons until the Apple logo appears(about 15 seconds). It should then restart.

  • My iPad will not turn off

    My iPad will not turn off. The power button no longer seems to do anything. Any ideas.

    Try reset iPad
    Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
    Note: Data will not be affected.

  • My camera light will not turn off

    My camera light will not turn off.  How do I get it to turn off?

    1. Try a Restart by pressing the sleep/lock button until you see the slider.  Slide to power off.  Restart by pressing the sleep/lock button until you see the Apple logo.
    2. Try a Reset by pressing the home and sleep buttons until you see the Apple logo. Takes about 5-15 secs of button holding and you won't lose any data or settings.

Maybe you are looking for

  • Airplay display keeps breaking up from my new Mac book. Help!

    When using the airplay from my iPhone or iPad the picture and audio works well. No breaking of picture or audio. When I try do the same from my new mac book pro the picture and audio keep breaking up, which is very frustrating considerng the new mac

  • Aligning ink cartridges

    I replaced ink cartridges now every time I turn on my hp psc 1315v all in one it prints another alignment page and tells me to align print cartridges I have done this repeatedly,but it keeps printing and telling me to align.I have removed and replace

  • Saving a FCP 6 file to be used in FCP 5

    Is there a way to save or revert a FCP 6 file to the previous version FCP 5.

  • BB Desktop Manager error 1316 (windows 7) - cannot be uninstalled

    Hi, I am new to the forum, because I cannot seem to find an answer to my query anywhere. I have a fairly new Dell laptop which has Windows 7 installed. When I first got it, I installed BBDM on it and did a couple of back ups (so it did work at some p

  • How to add png icons on image

    i have captured an image from the camera and now i want to add some png icons on that image these png icons are in the list,i want to select an icon and place it on the desired location on image, will any one guide how can i start with that thx in ad