PXIe acquiring and disk streaming speed

Good evening,
I need to acquire and stream to disk the status of N.8 digital lines at 100 MHz clock, idest 100MBytes/sec data rate, in continuously mode (without data loss) for five minutes.
I've thought to a PXIe configuration with:
PXIe 6544 High speed DIO,
PXIe 1071 Chassis,
PXIe Controller with solid state H.D. option.
Is that configuration enough?
Thanks.
Natalino Roberto

Hello Roberto,
According to NI PXIe-6544 specifications, you should be able to achieve typical data streaming rates 400 MB/s for acquisition and 400 MB/s for generation. So, you shouldn't face with any issue from this side.
Does your application provide an host interface communicating with embedded application? If doing so, you may need to design your application according real time guidelines.
Let me know if you need help or additional assistance.
Have a nice day.
Matteo C. - Test Engineer

Similar Messages

Audio and Video streaming speed to high

I'm struggling for a couple of weeks to stream fm radio to my BB. It switches over to wap, and right after that the buffer starts filling. I hear a coupke of seconds of normal sound, and then the speed doubles. Anyone knows what i'm doing wrong?

It is video transmission only. That is the only example I can find that comes close to what you are trying to do. Together along with this demo:
http://www.ni.com/white-paper/13881/en/
You may be able to piece together what you are trying to do. Other than that, I don't see any current audio/video streaming examples. If you pursue this application, don't forget to give back to the community!
http://www.ni.com/examples/

New Homehub and download/streaming speeds still sl...

Hi,
Just received a new Homehub 3 today and it has not disconnected from the broadband yet however my download and streaming speeds are much slower than they were before I started experiecing faults with the previous homehub. Does this mean it take a few days for my connection to become stable again? I've tried different channels and that has not helped at all.

Is this okay?
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
0 days, 01:24:39
Downstream:
5.844 Mbps
Upstream:
448 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
15.7 dB / 23.0 dB
Line attenuation (Down/Up):
32.2 dB / 18.0 dB
Output power (Down/Up):
19.7 dBm / 11.9 dBm
FEC Events (Down/Up):
80 / 0
CRC Events (Down/Up):
0 / 0
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
0 / 0
Error Seconds (Local/Remote):
0 / 0
If there is no problem with the stats could there be something wrong with my line or do I need a new microfilter? Tech support at BT suggested that I should get a new master socket installed and it could be causing porblems with my connection. However I have had BT Broadband for almost 2 years now and my download and steaming speeds have usually remained high and consistent throughout that time period.

Safari won't open certain web pages and download/stream speed slow

I have recently been experiencing problems with viewing certain websites, content on websites, streaming video, and downloading files. Sometimes the website will load but all the images will be blue question marks. I cannot get anything to load on youtube. Streaming video on Netflix is really slow as well. My bandwidth allowance on my network is 3 mbps (I'm the only user) and I have been getting between 40-300 kbps when downloading things. I have restarted Safari, my computer, and still no change. Any idea on what's going on? Thanks!
Machine:
Snow Leopard 10.6.8
2.16 GHz Intel Core 2 Duo
2 GB 667 MHz DDR2 SDRAM

Welcome to Apple Support Communities.
You're not alone. Others, especially with early MacBooks, have reported slower Safari performance after updating to OS X 10.6.8. and Safari 5.1
Using any popular search engine with the terms "mac os x 10.6.8 slow internet" will reveal dozens of similar complaints.
I did too with my mid-2007 MacBook, similar to yours, except I have 4GB RAM (3 GB usable). After a few days of 'spinning beachball' I restored my system to OS X 10.6.7 and internet performance returned to what I remembered.
One of the longer threads with a number of suggestions is here:
https://discussions.apple.com/thread/3142362?start=0&tstart=0

Brand new MacBook Pro has really slow download and streaming speeds

I'm new to Macs, and don't know much about computers in general. But I got a 13" MacBook Pro almost two weeks ago and have been experiencing really slow download and video streaming speeds. Pages load one image at a time, Netflix is almost impossible to use because the videos will stop buffering every five minutes even if I let them buffer for more than ten minutes. I haven't been experiencing any issues with wifi on my phone, and I've troubleshot our router. I'm not sure what it could be--but then again, I don't know a whole lot. Before I go running off to the Apple Store or call support, is there anything I can try in the meantime? Thanks!
Here are the system specs:
Processor 2.4 GHz Intel Core i5
Memory 4 GB 1600 MHz DDR3
Graphics Intel Iris
Software OS X 10.9.3 (13D65)
74.23 GB free out of 120.47 GB

Check with your isp regarding your download & upload speeds as well as streaming. You need to determine if the issue is on their end. You can also check on the speedtest.com website. Compare what your isp tells you to the net speed website.

How to acquire data through multiple channels in parallel using PXI 6070 E, PXI 4071 and LabVIEW?

Hi,
I am using NI LabVIEW, NI PXI 4071, and NI PXI 6070E to measure current through a variable resistance. Now, I am using one channel from SCB-68, but I want to add another channel in parallel so that I can have two resistors instead of one that I cam measure current through them.
I have attached a Pdf file showing the setup for hardware in use and LabVIEW code also.
Can anyone look at these files and give me guide lines or ideas that can help me resolving this issue, please.
Thanks in advance.
Best Regards,
Shaheen.
Solved!
Go to Solution.
Attachments:
IV copy for HS.vi ‏55 KB
Layout of NI Cards.pdf ‏248 KB

Your 4071 can only do one measurement at a time. Your DAQ cannot measure resistance either nor has it got any analogue inputs.
However, you could use a multiplexer and multiplex your 4071 DMM. This wont give you simultaneous measurements but can acquire data one after the other, the speed is obviously dependent on the multiplexer you choose!
Hope this helps.
Beginner? Try LabVIEW Basics
Sharing bits of code? Try Snippets or LAVA Code Capture Tool
Have you tried Quick Drop?, Visit QD Community.

Ipad mini with retina display has really slow and laggy streaming but very high download speed

I just got my ipad mini with retina display yesterday. The regular internet works fine as far as I can tell. I tried streaming video from watch espn, netflix, and youtube, and all three apps were so slow I couldn't watch anything. I have a high download speed too, it is 15 Mbps. I tried turning off the QOS engine in my router, and my download speed was up to 30 Mbps, and I still had the same terrible streaming quality. I tried changing the DNS as well, and this did nothing. I tried doing all the restarting and other "quick fixes," and nothing seems to work. Can anybody help me?

I requested your post be moved to the iPad forum. This is the Mac Mini desktop forum

Journaling and Disk Speed

How much speed penalty do you take for having Journaling turned on for your main hard disk?

Not a great deal but there is some reduction in speed. If you work with large files and data access speed is critical to your needs, then you may see a slight benefit from disabling journaling. The trade-off is crash recovery. Journaling helps improve recovery from crashes caused by power outages or sudden shutdowns.
Here are two (slightly old) articles that explain about journaling:
http://www.lafcpug.org/featuresfilejournaling.html
http://docs.info.apple.com/article.html?artnum=107249

Rented movie not playing. I have 81Mbps Internet and can stream anything else HD. it's not WiFi either because signal strength is full and I can view anything other than rented movies on apple TV unit. it charges me for renting but doesn't play

Rented "Gone Girl" on apple tv. It charges me, but will not play for more than 4 seconds at a time. I have exercised every step of apple's troubleshooting and nothing fixes the problem. I have a very strong, steady 81 Mbps Internet connection speed and can stream any other HD through the apple tv except for this rented movie. This is not the first time this has happened either. I just gave apple $6 for free and am currently watching the movie streaming through my cable provider's on demand channel with ease. Oh yeah, and when I seek apple support for the issue, apple wants $2 just to contact someone! Give me my money back please and I will never attempt to use your poor tv service again.

The limitation of approximately 200 titles has been discussed before, we can't be sure whether it will be something that gets fixed or not. I'm not really sure what your other issues are, if I use search instead of lists, I find whatever I want and am able to rent or purchase subject to those options being available for that particular title.

How to find out the Streaming speed of a flash player?

Hi guys!
I am Testing web site which is having a flash video files. if I select an video file, it will open a new window and play the video.
now I want to find out the video player in which band with using to play with out any buffering.
Actually our client specified that player can play with out any buffering at 700kbps, I have 1Mb leased line, still it is buffering while playing the video.
Please help to me how find out the streaming speed of player.
Thanks
Tonny

Hi Markus,
I don't think ,there is any report which can help to get the serial no of AP.
Inventory( Report >Report Launch Pad> Inventory) is the ONLY report which gave the below information but NOT the serial no .
Inventory
This report allows you to generate inventory-related information for controllers, access points, and MSEs managed by Prime Infrastructure. This information includes hardware type and distribution, software distribution, CDP information, and other statistics.
*** If anyone knows more deatils on this ,please share with us ***
Thanks-
Afroz
[Do rate the useful post]

Poor SSD disk IO speed in Oracle Linux 6.3 (Windows migration)

Hello,
I am trying to migrate from Windows to Oracle Linux, but I'm seeing very poor disk IO speeds. It's probably a tuning thing, but I'm relatively new to Oracle Linux and could use some detailed advice.
I took one physical server and migrated it from Windows 2008R2 to Oracle Linux 6.3 while maintaing the same Oracle version (11.2.0.3 Enterprise with ASM) and the same hardware (quad CPU 48 core HP DL585 G7 with 128GB RAM, 7 LSI 9200-8e HBAs, 28 Samsung SSD Drives). Disk IO performance, as measured using Oracle IO Calibration, was ~7,800MB/Second and 440K IOPS under windows but fell to ~2,400MB/Second and 250K IOPS under Linux.
Oracle Linux and the DB were installed using default values. The Oracle tools seem to have done a great job setting all of the obvious IO tuning parameters like the scheduler, but I figure that there are other important IO-related OS or DB parameters and that I have failed to configure the system properly.
My goal for the migration is sequential read IO speed and I would have bet money that Linux would provide better performance than Windows. I still think that it should. What basic IO tuning should I do for Oracle Linux using ASM and SSD drives?
Thank you!
Some details:
Oracle DB 11.2.0.3 enterprise installed via the GUI with the "Data Warehousing" template
ASM - single disk group, 28 SSD disks, AU=4MB
Oracle memory: Automatic memory management, 64GB allocated
Non-default Oracle params: filesystemio_options=setall, disk_asynch_io=true
Edited by: 975524 on Dec 7, 2012 8:56 AM

Thanks "dude" for the advice. Unfortunately, I am still seeing low IO speeds.
The default scheduler for OEL 6.3 with the DB pre-install package is deadline, which seemed like a far better choice than CFS. Based on your advice, I tried noop this morning and got the same results. I also tested with and without hugepages and saw only a small difference - at least in IO speed - I did not test overall DB performance. Lastly, I understand the /dev/shm issue, but even with the default configuration I'm getting 64MB allocated to Oracle, which is far more than is needed to test sequential IO - in fact I can get better results by using less RAM.
To answer your questions, I am testing using Oracle IO Calibration, which is an IO testing feature of the Oracle DB that is similar to the standalone Oracle Orion tool. I also performed a few tests using IOMeter, but found that the Linux version of that product was not giving me consistent data. The overall trend was the same however - IO on the Linux version far lower than the same hardware running Windows. The system is functioning very well, so I assume that everything has been installed correctly, but I do not think that it was installed optimally - thus my cry for help.
I am so surprised that Linux is showing slow IO!
Edited by: 975524 on Dec 7, 2012 9:22 AM

Decreased streaming speed after 10.5.7 update?

Has anyone had a decrease in streaming speed after the last mac security update package? I used to be able to watch video's direct from a site now i have to wait for a good 15-20 mins so i get a large buffer zone and then i can sometimes watch without interruption.

resolved...

How should i allocate the right RAM and disk space to windows through boot camp or parallels ?

i am trying to understand how you need to set things up when trying to run windows from a mac ( using bootcamp / parallels ). i want to understand the implications around RAM.
i have a mac with 1terra SSD and 16 GB of RAM, and if i want to install windows i need to partition and allocate memory and disk space for windows.
now i would be running on windows :
cad 2015
revit / rhino
photoshop and some other graphic softwares
so my questions are:
how do i decide how much space should be allocated to windows and once i decide that, can i change it later ?
how do i decide what RAM should be allocated to windows. and can i also change that in the future ?
now lets say i allocated 8 GB of RAM for winddows using bootcamp, does that mean that every time i log into my mac through OS, it will only be using 8GB of the total RAM ?
here's my last question : i have my parallels software yet to be installed, just as the windows 8 software. now should i use bootcamp to install windows ? could i install windows using parallels ? if yes which is better to use ?

oliverfrombeirut wrote:
so my questions are:
how do i decide how much space should be allocated to windows and once i decide that, can i change it later ?
how do i decide what RAM should be allocated to windows. and can i also change that in the future ?
now lets say i allocated 8 GB of RAM for winddows using bootcamp, does that mean that every time i log into my mac through OS, it will only be using 8GB of the total RAM ?
here's my last question : i have my parallels software yet to be installed, just as the windows 8 software. now should i use bootcamp to install windows ? could i install windows using parallels ? if yes which is better to use ?
1. Windows needs 60GB for good performance, add the needs of the apps you intend to use and I would say no less than 100GB. (it can be changed later but it is not an easy task unless you pay for Camp Tune)
2. You do not allocate Ram to Windows in Boot Camp. Windows will use all of it (64bit Windows) or 4GB (32bit Windows)
3. See 2
4. Use Boot Camp, Parallels will not allow Windows to run at full speed.
General Notes:
1. Make a complete backup of your Mac before you start! (do not skip this)
2. Read the Boot Camp directions, then read them again.

Help me understand my up-stream speed

Despite having excellent down-stream speed, I have been having problems with insufficient up-stream bandwidth for a long time. This causes me problems with a Vodafone Sure Signal to the point that I can't really use it for my mobile calls unless there is no other traffic on my broadband.
I have bounced between Vodafone support who tell me that I don't have enough up=stream bandwidth and I must speak to BT, and BT who tell me that my upstream speed is fine and there is nothing that can be done.
Until this weekend I though that my Broadband connection was typical with 448/7680 sync speeds. The BT speed tester doesn't show me my up-stream info. I'm not sure if it's because I'm a BT Vision customer, but instead it gives:
Test1 comprises of two tests
1. Best Effort Test: -provides background information.
Download Speed
5600 Kbps
0 Kbps
7150 Kbps
Max Achievable Speed
Download speedachieved during the test was - 5600 Kbps
For your connection, the acceptable range of speeds is 600-7150 Kbps.
Additional Information:
Your DSL Connection Rate :7680 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
IP Profile for your line is - 6500 Kbps
2. Assured Rate Test: -provides background information.
Download Speed
2125 Kbps
0 Kbps
600 Kbps
Max Achievable Speed
Download speedachieved during the test was - 2125 Kbps
For your connection, the acceptable range of speeds is 576-600 Kbps.
Additional Information:
Assured Rate IP profile on your line is - 600 Kbps
We were unable to identify any performance problem with your service at this time.
This weekend I helped my mother get a new broadband connection up and running and after the initial Home Hub 3 connection her speed test results were (printing to PDF initially mixed the data up):
Test1 comprises of two tests
1. Best Effort Test: -provides background information.
2. Upstream Test: -provides background information.
We were unable to identify any performance problem with your service at this time.
Download
Speed
2973 Kbps
0 Kbps 4000 Kbps
Max Achievable Speed
Download speed achieved during the test was -
2973 Kbps
For your connection, the acceptable range of speeds is
1200-4000 Kbps.
Additional Information:
Your DSL Connection Rate :
3648 Kbps(DOWN-STREAM), 1135 Kbps(UP-STREAM)
IP Profile for your line is -
3218 Kbps
Upload Speed
851 Kbps
0 Kbps 1135 Kbps
Max Achievable Speed
>
Upload speed achieved during the test was - 851 Kbps
Additional Information:
Upstream Rate IP profile on your line is -
1135 Kbps
This means that her download speed is approx half of mine, but her upstream is double !!!!
How is the up-stream speed determined, and more importantly how can I get my upstream speed to a more acceptable speed?
My Home Hub 3 stats are
Connection Information
Line state:
Connected
Connection time:
0 days, 23:07:45
Downstream:
7.5 Mbps
Upstream:
448 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Fast
Noise margin (Down/Up):
10.6 dB / 30.0 dB
Line attenuation (Down/Up):
18.7 dB / 9.0 dB
Output power (Down/Up):
19.9 dBm / 12.3 dBm
FEC Events (Down/Up):
0 / 0
CRC Events (Down/Up):
6 / 0
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
3 / 0
Error Seconds (Local/Remote):
6 / 0
Thanks for any help.
Solved!
Go to Solution.

you are on adslmax and the max upstream connection is 448 whereas your mother is on 21cn adsl2 with an upstream of about 1000. until your exchange is upgraded to 21CN you will not get a faster upload connection
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Do I need to keep older Final Cut docs and disks?

I'm trying to find out if I need to keep all of the documentation and disks to my licensed and registered Final Cut software. I've currently got Final Cut X installed. But, I have all manuals and install disks going back to Final Cut 1.0. I'm moving and would really like to not have take all the cumbersome Final Cut boxes with me. If I can get rid of them, how do I dispose of or recycle the paper and disks? Any chance I'll need any of it if I want to upgrade in the future?

Here's the section of the SLA on transfering to another owner: (from http://images.apple.com/legal/sla/docs/finalcutstudio2.pdf)
"3. Transfer. You may not rent, lease, lend, sell, redistribute or sublicense the Apple Software. You may, however, make a one-time permanent transfer of all of your license rights to the Apple Software to another party, provided that: (a) the transfer must include all of the Apple Software, including all its component parts, original media, printed materials and this License; (b) you do not retain any copies of the Apple Software, full or partial, including copies stored on a computer or other storage device; and (c) the party receiving the Apple Software reads and agrees to accept the terms and conditions of this License. All components of the Apple Software are provided as part of a bundle and may not be separated from the bundle and distributed as standalone applications.
Updates: If an Apple Software update completely replaces (full install) a previously licensed version of the Apple Software, you may not use both versions of the Apple Software at the same time nor may you transfer them separately.
NFR (Not for Resale) Copies: Notwithstanding other sections of this License, Apple Software labeled or otherwise provided to you on a promotional basis may only be used for demonstration, testing and evaluation purposes and may not be resold or transferred.
Academic Copies: If the Apple Software package has an academic label or if you acquired the Apple Software at an academic discount, you must be an Eligible Educational End User to use the Apple Software. "Eligible Educational End Users" means students, faculty, staff and administration attending and/or working at an educational institutional facility (i.e., college campus, public or private K-12 schools)."

PXIe acquiring and disk streaming speed

Similar Messages

Maybe you are looking for