QinQ support on Cisco SUP7L-E?

Current release note for Cisco IOS XE Release 3.2.0XO says:
These sections list the limitations and restrictions for the current release of Cisco IOS software on the Catalyst 4500E series switch.
•802.1q tunneling and related features are not supported.
but in feature navigator there is 802.1q available
- IEEE 802.1Q Tunneling
- Selective QinQ
Sup 6E has support also:
Be aware that 802.1Q requires WS-C4948, WS-C4948-10GE, ME-4924-10GE, WS-C4928-10GE, WS-C4900M, WS-X4013+10GE, WS-X4516, WS-X4516-10GE, or WS-X45-SUP6-E; Layer 2 protocol tunneling is supported on all supervisor engines.

Hi Riccardo,
I checked the tables and for my unterstanding SUP7L-E and SUP7-E are SW feature parity…
Out of the release note:
Additionally, Supevisor Engine 7L-E running Cisco IOS 3.2.0XO has feature parity with Supervisor Engine 7-E running Cisco IOS XE 3.2.0SG.
The feature set for Supervisor Engine 7L-E matches that of Supervisor Engines 7-E
That means Q-in-Q should also work on SUP7L-E within next IOS release (March – May 2012) … or am i wrong?
Thanks
Manuel
Von: rsimoni
Gesendet: Dienstag, 10. Januar 2012 16:52
An: Linder Manuel (CASSARiUS AG)
Betreff: - Re: QinQ support on Cisco SUP7L-E?
Home
Re: QinQ support on Cisco SUP7L-E?
created by Riccardo Simoni in Other Service Provider Subjects - View the full discussion

Similar Messages

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP's?

What are the features supported in Cisco Prime Infrastructure for WLAN for autonomous AP’s?

• PI provides visibility for autonomous clients within the same list view as lightweight and wired clients (client list page).
• Rogue AP detection for autonomous AP's is not supported (it's supported in CUWN).
• Alarms/events for client authentication issues (e.g. authentication failure) are displayed in PI.
• Config management for autonomous AP's is via CLI template. Config comparison and archiving functionality in PI leverages these same features that were brought in from LMS, so need to defer to others in terms of whether this is a cross-platform feature in PI or is only supported on a subset of platforms. Config comparison/archive is supported in CUWN.PI supports both infrastructure (e.g. AP Tx Power and Channel, busiest AP, AP utilization, etc.) and client (e.g. client count, client sessions, etc.) reports, and there are extensive reports for CUWN

Dynamic Routing Protocol Support in Cisco ASA Multiple Context Mode

                   Dear Experts,
Wold like to know whether dynamic Routing Protocol Support in Cisco ASA Firewall Multiple Context Mode. If yes then please provide OS version and Hardware Model of Cisco ASA Firewall. Appreciate the quick response. Thanks.

Hi,
Check out this document for the information
http://www.cisco.com/en/US/docs/security/asa/roadmap/asa_new_features.html#wp93116
Its lists the following for software level 9.0(1)
Multiple   Context Mode Features
Dynamic routing in Security   Contexts
EIGRP and OSPFv2 dynamic   routing protocols are now supported in multiple context mode. OSPFv3, RIP, and multicast routing   are not supported.
Seems to me you would need some 9.x version to support the above mentioned Dynamic Routing Protocols.
I don't think its related to the hardware model of the ASA other than that it requires a model that supports Multiple Context Mode. To my understanding the only model that doesnt support that is ASA5505 of the whole ASA5500 and ASA5500-X series.
Hope this helps
- Jouni

Is VSS supported in Cisco Prime Infrastructure 1.2?

Is VSS supported in Cisco Prime Infrastructure 1.2?

VSS support (converting standalone switches into a VSS) was introduced with LMS 3.0.1 if I remember well and it is still there in LMS 4.2 (Cisco Prime Infrastructure):
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/user/guide/configuration/configvss.html
Config Mgmt is supported, also.

If we got Nexus 1000V from VMWARE , can we add the N1K to our CCO ( Cisco Account ) to have direct support from Cisco

Hi
If we got Nexus 1000V from VMWARE , can we add the N1K to our CCO ( Cisco Account ) to have direct support from Cisco
as sometimes it take some more time to get answer from VMWARE -> Cisco
Thanks

No. When you purchase support from Vmware, they are your support contact and they will escalate support to Cisco on your behalf if needed. This is the case for all OEM support. Cisco provides support for RHEL, Microsoft and VMware. We follow the same practice.
Deciding who to purchase support from is a decision of single point of contact for all VMware & N1K related issues vs. maintaining separate support contracts with each vendor individually.
Regards,
Robert

MPLS CE support on Cisco 2800 ISR router

Hi all, could I ask you for some hints about MPLS CE support on Cisco 2800 ISR router today? I`m finding restrictions and recommendations for feature implementation. Do you have any cisco web site about them?
Thank you for your advice and/or hints.
Peter

Thanks for an answer. I need to use multi-VPN model on CE router, but with QoS on one physical CE-PE connection (e.g. Frame-Relay DLCI).However, all VPNs on CE router must be secured for each one. The solution is Multi-VRF service feature, but, however, with multi-DLCI model on Frame-Relay and QoS per DLCI. Now, I`m finding a scenario to provide multi-VPN model on CE router with single-DLCI model and single QoS per one DLCI for all VPNs. And that, MPLS CE feature on C2800 could be used, if possible.
So, I don`t know more about MPLS CE on C2800 and I don`t know make a result to propsed solution...

EoMPLS support on Cisco ISR G2 2921?

Hi there is saw in feature navigator that EoMPLS is a supported feature for 2921...
- Can somebody please confirm that EoMPLS is supported with Cisco 2921?
- Is pseudowire redundancy possible?
Thanks
Manuel

Hi Manuel,
yes it is supported (if I am not wrong since release 12(4)T) and also L2VPN PW redundancy is supported.
Riccardo

How many numbers of GRE Tunnels are supported on Cisco 3925 router?

Hi...
I would like to know that.......
How many numbers of GRE Tunnels are supported on Cisco 3925 router?
Thanks....

This is what I found in my search:
There may be factors such as memory constraints that will place practical limits on how many tunnels you can support. But there is also a hard limit on the number of tunnels that you can configure. That limit is based on the limitation of the number of IDBs supported by your router. The IDB is the Interface Descriptor Block and each interface (physical, or tunnel, or loopback, or whatever) requires an IDB. The number of IDBs will vary by platform and sometimes by release level of the code that you are running. You can use the privileged command show idb to see what the limitation is on your router. On the 1841 router that I just checked the limit on IDB is 1200 (which is a pretty large number - I believe that you would encounter other limits on performance or on size of configuration before you exhaust the IDB limit).
https://supportforums.cisco.com/thread/2007932
Hope it helps.
Jatin Katyal
- Do rate helpful posts -

Can IPV6 QOS support in Cisco 3750x switches

Hi
I have tried IPv6 qos using class map in Catalyst 3750 switches but the platform is not support.
Can anyone configured the IPV6 qos in Cisco 3750-X switches. Does it support?
Cisco 3750 config
policy-map up
class bwtest-up
police 2048000 128000 exceed-action drop
policy-map down
class bwtest-down
police 512000 128000 exceed-action drop
trust dscp
class-map match-all bwtest-up
match access-group name bwup
class-map match-all bwtest-down
match access-group name bwdown
ipv6 access-list bwup
permit ipv6 2402:xxxx:x:x::/64
ipv6 access-list bwdown
permit ipv6 any 2402:xxxx:x:x::/64
L3(config)#int g1/0/4
L3(config-if)#service-policy input up
QoS: class(bwtest-up) IPv6 class not supported on interface GigabitEthernet1/0/4 ( error)
Please help!

interface GigabitEthernet1/0/4
description ##Test LAN-IPV##
no switchport
bandwidth 2048
no ip address
load-interval 30
speed 100
duplex full
ipv6 address 2402:xxxx:x:x::1/64
ipv6 enable
ipv6 ospf 200 area 0
end
switch sw version
Cisco IOS Software, C3750 Software (C3750-IPSERVICESK9-M), Version 12.2(55)SE9, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Mon 03-Mar-14 22:45 by prod_rel_team
Image text-base: 0x01000000, data-base: 0x02F00000
ROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)
Cherry uptime is 6 days, 7 hours, 23 minutes
System returned to ROM by power-on
System restarted at 07:04:50 IST Thu Mar 19 2015
System image file is "flash:/c3750-ipservicesk9-mz.122-55.SE9.bin"

Are HTTPS probes supported in Cisco devices ?

Hello,
I am aware Cisco supports HTTP probe types. Are HTTPS (HTTP Secure) probes are supported in Cisco devices too ? If so from which IOS version ?
Your comments are very much appreciated.
Thanks.

Hi ,
As per my understanding there is No IOS code which support HTTPS opeartions , Only HTTP operations are supported as of now.
Thakns
Afroz

Maximum cos1 (voice traffic) supported by Cisco ASR 1006 router

Dear Team,
Please confirm the maximum cos 1 traffic supported by cisco ASR 1006 router.

Yes, it would. If you are planning on terminating a single site on this router I would spread over multiple routers for redundancy.
Table 6 explains number of ports and channels providing you have the DSPs:
http://www.cisco.com/c/dam/en/us/products/collateral/routers/2800-series-integrated-services-routers-isr/product_data_sheet0900aecd8057f2e0.pdf

IPv6 support in Cisco UC - especially CUAC

Guys,
Does anyone have any recent detailed information on IPv6 support and Cisco UC? The documentation on CCO is out of date by 3 years and doesn’t include information on applications such as Attendant Console (CUAC). The latest documentation from the UC 10.0 Beta Training is very high level. With key features like extension mobility not supporting IPv6, it’s difficult for us to advise customers on deploying a Cisco UC deployments whilst they are planning migrations to IPv6.
Does CUAC support IPv6?
Any updated details on Cisco UC support would be very much appreciated!
Thanks
Jonny

The philosophical direction of Cisco is to have full IPv4 and IPv6 parity across feature sets. Any IPv4 feature should appear in the same license level of software for IPv6.
That said, some older software and platforms may have been missed.
See
https://supportforums.cisco.com/community/netpro/network-infrastructure/ipv6-transition/blog/2011/09/21/ipv6-feature-packaging-in-cisco-routers-and-switches
See if the problem persists with the latest version. If so, I'd treat it as a bug and open a case.

No of SSID support on Cisco WLC

Hi All,
Can you please help me on providing below details on Cisco wireless controller?
1. No of SSID support on Cisco WLC
2. Is it possible to restrict SSID on AP's (e.g. I have 10 SSID's configured on controller, I want first 10 Access points use set of SSID (SSID 1-5), and rest of the AP use SSID 6-10.
Thanks
Jamal

Hi Jamal,
Just to add a touch to the great info from Robert (+5 points Robert)
The feature you are looking for is called WLAN Override in WLC 4.x versions.
Enabling WLAN Override
By default, access points transmit all defined WLANs on the controller. However, you can use the WLAN Override option to select which WLANs are transmitted and which ones are not on a per access point basis. For example, you can use WLAN override to control where in the network the guest WLAN is transmitted or you can use it to disable a specific WLAN in a certain area of the network.
From this doc;
http://www.cisco.com/en/US/docs/wireless/controller/4.0/configuration/guide/c40wlan.html#wp1114777
Once you create a new WLAN, the WLAN > Edit page for the new WLAN appears. In this page you can define various parameters specific to this WLAN including General Policies, RADIUS Servers, Security Policies, and 802.1x Parameters.
**Check Admin Status under General Policies to enable the WLAN. If you want the AP to broadcast the SSID in its beacon frames, check Broadcast SSID.
Note: You can configure up to sixteen WLANs on the controller. The Cisco WLAN Solution can control up to sixteen WLANs for Lightweight APs. Each WLAN has a separate WLAN ID (1 through 16), a separate WLAN SSID (WLAN name), and can be assigned unique security policies. Lightweight APs broadcast all active Cisco WLAN Solution WLAN SSIDs and enforce the policies that you define for each WLAN.
From this good doc;
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a0080665d18.shtml#c3
In 5.x versions you will use AP Groups, because in WLC 5.x versions, WLAN Override has been replaced with the "AP Groups" feature;
Creating Access Point Groups
After all access points have joined the controller, you can create up to 150 access point groups and assign up to 16 WLANs to each group. Each access point advertises only the enabled WLANs that belong to its access point group. The access point does not advertise disabled WLANs in its access point group or WLANs that belong to another group.
http://www.cisco.com/en/US/docs/wireless/controller/5.2/configuration/guide/c52wlan.html#wp1128591
To learn more about AP Groups check out George's excellent video
http://www.my80211.com/cisco-labs/2009/3/22/cisco-ap-group-nugget.html
Hope this helps!
Rob

C2600xm MPLS and QinQ support

Does anybody know an IOS version that supports both MPLS and QinQ support. Nearly all advance enterprise services 12.4 support QinQ and some 12.3T, but i believe that later versions of IOS 12.3 and onwards removed MPLS support. I could really do with finding both these features in the same IOS as it would greatly help me study. IOS selector is hard to trust as it doesnt appear to label MPLS support under some IOS which i know have the commands. Also certain 12.3T ios have been deferred which makes getting them to try hard to begin with.
So far i have tried the below.
c2600-adventerprisek9-mz.123-11.T.bin <-- QinQ no mpls
c2600-adventerprisek9-mz.123-26.bin <-- no QinQ
c2600-advipservicesk9-mz.123-4.T6.bin <--no QinQ
c2600-telco-mz.123-26.bin <-- MPLS but no QinQ
c2600-telco-mz.124-7.bin <- no MPLS
All the 12.4 IOS have had the tag-switching/MPLS commands removed.
Any help will be most appreciated!

Hi,
If your CE at both ends are routers, then you can configure both CE's with a Sub interface on the trunk link that is going towards PE. On this Sub interface of CEs you can configure IP address and also, if CEF is enabled on router and the interface then you can use mpls ip command on this sub interface and form LDP neighborship between both CEs over this l2 circuit.
Yes MTU size will have to be capable of supporting this increased packet size.
Regards,
Shailendra

Android tablets supported for Cisco Jabber for Android 10.5 ?

Exist a list with tablets support for this realease ?
In release notes only include smartphones.
Anoher question, is about version android client, in google play exits a old version, but not 10.5, any reason for this ?
Thanks in advance.

The tab listed for support is " Google Nexus 10 (Android OS 4.4.x) ". Please refer to the following link for more information;
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/jabber/10_5/CJAB_BK_D6497E98_00_deployment-installation-guide-ciscojabber/CJAB_BK_D6497E98_00_deployment-installation-guide-ciscojabber_chapter_011.html#CJAB_RF_D3CF90B1_00
Quoting the following link; https://play.google.com/store/apps/details?id=com.cisco.im&hl=en ;we have got the J4A 10.5 listed on the playstore.
- please rate if this helps.

QinQ support on Cisco SUP7L-E?

Similar Messages

Maybe you are looking for