Qla2310f not shown in cfgadm/luxadm (san 4.4.11)
I have a problem, with two qlogic qla2310f HBA�s (not sun branded) that are not detected in luxadm/cfgadm.
The box is a SUN Fire 280R running solaris 8:
SunOS [hostname] 5.8 Generic_117350-27 sun4u sparc SUNW,Sun-Fire-280R
Originally it was connected to an older eva-san(HP) using HP-securepath 3.0d for multipathing.
When changing to a new EVA8000 san, i did the following:
1. Unmounted the san-disks, removed them fra Solstice.
2. deletede them in spmgr (HP Securepath)
3. unpresented the disks
4. unistalled Hp Securepath
5. presented disks from the new san (EVA8000)
6. installed SAN 4.4.11 and required pathces, using the "install_it" script
7. modified /kernel/drv/scsi_vhci.conf to enable mpxio globally and add hp specific Symmetric options for the eva8000 san.
After the reconfiguration reboot, i see the disks - however, i Cant see the two qla2310f in luxadm/cfgadm.
These utillities only see the internal controller, and the two internal disks:
Luxadm shows:
luxadm probe
No Network Array enclosures found in /dev/es
Found Fibre Channel device(s):
Node WWN:20000004cfbff6be Device Type:Disk device
Logical Path:/dev/rdsk/c1t0d0s2
Node WWN:2000000c500739e5 Device Type:Disk device
Logical Path:/dev/rdsk/c1t1d0s2
luxadm fcode_download -p
Found Path to 0 FC/S Cards
Complete
Found Path to 0 FC100/S Cards
Complete
Found Path to 1 FC100/P, ISP2200, ISP23xx Devices
Opening Device: /devices/pci@8,600000/SUNW,qlc@4/fp@0,0:devctl
Detected FCode Version: ISP2200 FC-AL Host Adapter Driver: 1.15 04/03/22
Complete
Found Path to 0 JNI1560 Devices.
Complete
Found Path to 0 Emulex Devices.
Complete
cfgadm shows:
cfgadm -l
Ap_Id Type Receptacle Occupant Condition
c0 scsi-bus connected configured unknown
c1 fc-private connected configured unknown
c2 scsi-bus connected unconfigured unknown
c3 scsi-bus connected unconfigured unknown
c4 scsi-bus connected unconfigured unknown
cfgadm -al
Ap_Id Type Receptacle Occupant Condition
c0 scsi-bus connected configured unknown
c0::dsk/c0t6d0 CD-ROM connected configured unknown
c1 fc-private connected configured unknown
c1::21000004cfbff6be disk connected configured unknown
c1::2100000c500739e5 disk connected configured unknown
c2 scsi-bus connected unconfigured unknown
c3 scsi-bus connected unconfigured unknown
c4 scsi-bus connected unconfigured unknown
Qlogics SANSurfer CLI shows all three adapters:
SANsurfer FC HBA CLI
v1.06.16 Build 57
Device List Menu
HBA Model QLA2300/2310:
1: Port 1 (OS 0): WWPN: 21-00-00-E0-8B-0D-AE-BF Online
HBA Model QLA2300/2310:
2: Port 1 (OS 1): WWPN: 21-00-00-E0-8B-0D-B6-BF Online
HBA Model qlc:
3: Port 1 (OS 0): WWPN: 21-00-00-03-BA-2F-AA-EF Online
4: All HBAs
cat /etc/path_to_inst |grep qla2300
"/pci@8,700000/QLGC,qla@3" 0 "qla2300"
"/pci@8,600000/QLGC,qla@1" 1 "qla2300"
the adapters are recognized at boot as well (and probe-scsi-all sees them as well as the san disks)
Oct 22 19:15:43 [hostname] qla2300: [ID 818750 kern.notice] QLogic Fibre Channel Driver v5.01 Instance: 0
Oct 22 19:15:43 [hostname] qla2300: [ID 572349 kern.notice] hba0: QLogic QLA2300 Fibre Channel Host Adapter fcode version 2.00.05 01/29/03
Oct 22 19:15:50 [hostname] qla2300: [ID 818750 kern.notice] QLogic Fibre Channel Driver v5.01 Instance: 1
Oct 22 19:15:50 [hostname] qla2300: [ID 572349 kern.notice] hba1: QLogic QLA2300 Fibre Channel Host Adapter fcode version 2.00.05 01/29/03
I currently use the disks "directly" without using multipathing:
ls -la /dev/dsk/c5t7d5s6
lrwxrwxrwx 1 root root 46 Oct 22 13:04 /dev/dsk/c5t7d5s6 -> ../../devices/pci@8,700000/QLGC,qla@3/sd@7,5:g
�
I need luxadm/cfgadm to "see" the two qla2310f adapters, in order to use multipathing, any ideas?
Same here:
V240 and X4200, QLF2340, Solaris 9 and 10 plus latest 9 recommended patch cluster connectec to McData and HDS.
Seems like a problem with luxadm and cfgadm, as on V480 with QLC2340 all works well...
Any new patches/fixes?
Cheers.
Similar Messages
-
ARIAL FONT IN REPORTS(WINDOWS), NOT SHOWN CORRECTLY UNDER LINUX
Our Reports are developed under Windows (Report Builder 9.0.4.0.33 and Windows 2000/Windows XP) and generated under Linux (IAS 10.1.2.0.2 with Red Hat Advanced Server). The Report Output is a PDF, that will be downloaded by the user with WEB.SHOW_DOCUMENT. This works fine, but fonts are not shown correctly in the PDF, especially ARIAL, which is the font we use.
I have run the Fontsolution Configuration Script from Metalink, but we still have a problem.
When you look at the font.pdf, wich is the testreport from fontsolutions, some sizes and styles of Arial are printed correctly others not.
Arial 8 is ok, but Arial 10 and Arial 12 are something like Times New Roman.
Arial 12 Bolded is correct, but Arial 12 italic and Arial 12 bold italic are also not
the Arial Font.
How can we correct this problem?
Regards
Udo
These are the files changed by Fontsolution Configuration Script:
uifont.ali
# uifont.ali provided in fontsolutions.tar for developer 9.0.2
# $Header: uifont.ali@@/main/22 \
# Checked in on Tue Jan 8 15:32:42 PST 2002 by idc \
# Copyright (c) 1999, 2002 by Oracle Corporation. All Rights Reserved. \
# $
# $Revision: /main/22 $
# Copyright (c) Oracle Corporation 1994, 2002.
# All Rights Reserved.
# DESCRIPTION:
# Each line is of the form:
# <Face>.<Size>.<Style>.<Weight>.<Width>.<CharSet> = \
# <Face>.<Size>.<Style>.<Weight>.<Width>.<CharSet>
# The <Face> must be the name (string/identifier) of a font face. The
# <Style>, <Weight>, <Width>, and <CharSet> may either be a numeric
# value or a predefined identifier/string. For example, both US7ASCII
# and 1 are valid <CharSet> values, and refer to the same character set.
# The <Size> dimension must be an explicit size, in points.
# The following is a list of recognized names and their numeric
# equivalents:
# Styles Numeric value
# Plain 0
# Italic 1
# Oblique 2
# Underline 4
# Outline 8
# Shadow 16
# Inverted 32
# Overstrike 64
# Blink 128
# Weights Numeric value
# Ultralight 1
# Extralight 2
# Light 3
# Demilight 4
# Medium 5
# Demibold 6
# Bold 7
# Extrabold 8
# Ultrabold 9
# Widths Numeric value
# Ultradense 1
# Extradense 2
# Dense 3
# Semidense 4
# Normal 5
# Semiexpand 6
# Expand 7
# Extraexpand 8
# Ultraexpand 9
# Styles may be combined; you can use plus ("+") to delimit parts of a
# style. For example,
# Arial..Italic+Overstrike = Helvetica.12.Italic.Bold
# are equivalent, and either one will map any Arial that has both Italic
# and Overstrike styles to a 12-point, bold, italic Helvetica font.
# All strings are case-insensitive in mapping. Font faces are likely to
# be case-sensitive on lookup, depending on the platform and surface, so
# care should be taken with names used on the right-hand side; but they
# will be mapped case-insensitively.
# See your platform documentation for a list of all supported character
# sets, and available fonts.
# BUGS:
# o Should accept a RHS ratio (e.g., "Helv = Arial.2/3").
#===============================================================
[ Global ] # Put mappings for all surfaces here.
# Mapping from MS Windows
#Arial = helvetica
#"Courier New" = courier
#"Times New Roman" = times
#Modern = helvetica
#"MS Sans Serif" = helvetica
#"MS Serif" = times
#"Small Fonts" = helvetica
"Sadvocra" = helvetica..Oblique.Medium
"sAdC128d" = helvetica..Plain.Medium
"CarolinaBar-B39-25F2" = helvetica...Bold
#"IDAutomationSMICR" = helvetica
# Mapping from Macintosh
#"New Century Schlbk" = "new century schoolbook"
#"New York" = times
#geneva = helvetica
#===============================================================
[ Printer ] # Put mappings for all printers here.
#===============================================================
[ Printer:PostScript1 ] # Put mappings for PostScript level 1 printers here.
# Sample Kanji font mappings
...UltraLight..JEUC = "Ryumin-Light-83pv-RKSJ-H"...Light..JEUC
...UltraLight..SJIS = "Ryumin-Light-83pv-RKSJ-H"...Light..SJIS
...ExtraLight..JEUC = "Ryumin-Light-83pv-RKSJ-H"...Light..JEUC
...ExtraLight..SJIS = "Ryumin-Light-83pv-RKSJ-H"...Light..SJIS
...Light..JEUC = "Ryumin-Light-83pv-RKSJ-H"...Light..JEUC
...Light..SJIS = "Ryumin-Light-83pv-RKSJ-H"...Light..SJIS
...DemiLight..JEUC = "Ryumin-Light-83pv-RKSJ-H"...Light..JEUC
...DemiLight..SJIS = "Ryumin-Light-83pv-RKSJ-H"...Light..SJIS
.....JEUC = "GothicBBB-Medium-83pv-RKSJ-H"...Medium..JEUC
.....SJIS = "GothicBBB-Medium-83pv-RKSJ-H"...Medium..SJIS
# Mapping from MS Windows
#Roman = palatino
#Script = "itc zapf chancery"
#FixedSys = courier
#System = helvetica
# Mapping from Macintosh
#"Avant Garde" = "itc avant garde gothic"
# Mapping from Motif display
#fixed = courier
#clean = times
#lucidatypewriter = courier
#lucidabright = times
#Arial = helvetica
#"Courier New" = courier
#"Times New Roman" = times
# MICR font
#helvetica=IDAutomationSMICR
#===============================================================
[ Printer:PostScript2 ] # Put mappings for PostScript level 2 printers here.
# Sample Kanji font mappings
...UltraLight..JEUC = "Ryumin-Light-83pv-RKSJ-H"...Light..JEUC
...UltraLight..SJIS = "Ryumin-Light-83pv-RKSJ-H"...Light..SJIS
...ExtraLight..JEUC = "Ryumin-Light-83pv-RKSJ-H"...Light..JEUC
...ExtraLight..SJIS = "Ryumin-Light-83pv-RKSJ-H"...Light..SJIS
...Light..JEUC = "Ryumin-Light-83pv-RKSJ-H"...Light..JEUC
...Light..SJIS = "Ryumin-Light-83pv-RKSJ-H"...Light..SJIS
...DemiLight..JEUC = "Ryumin-Light-83pv-RKSJ-H"...Light..JEUC
...DemiLight..SJIS = "Ryumin-Light-83pv-RKSJ-H"...Light..SJIS
.....JEUC = "GothicBBB-Medium-83pv-RKSJ-H"...Medium..JEUC
.....SJIS = "GothicBBB-Medium-83pv-RKSJ-H"...Medium..SJIS
# Mapping from MS Windows
#Roman = palatino
#Script = "itc zapf chancery"
#FixedSys = courier
#System = helvetica
# Mapping from Macintosh
#"Avant Garde" = "itc avant garde gothic"
# Mapping from Motif display
#fixed = courier
#clean = times
#lucidatypewriter = courier
#lucidabright = times
#===============================================================
[ Printer:PCL5 ] # Put mappings for PCL 5 printers here.
helvetica = univers
times = "cg times"
clean = "antique olv"
fixed = courier
lucida = univers
lucidabright = "cg times"
lucidatypewriter = courier
"new century schoolbook" = univers
terminal = "line printer"
#===============================================================
[ Display ] # Put mappings for all display surfaces here.
#===============================================================
[ Display:Motif ] # Put mappings for Motif displays here
# Fix for bug no 778937 DO NOT MOVE!
Roman.....sjis = lucida.....jeuc
Script.....sjis = lucidabright.....jeuc
FixedSys.....sjis = fixed.....jeuc
System.....sjis = lucida.....jeuc
.....sjis = .....jeuc
# Mapping from MS Windows
Roman = lucida
Script = lucidabright
FixedSys = fixed
System = lucida
# Mapping from Macintosh
"Avant Garde" = helvetica
"Bookman" = times
#===============================================================
[ Display:CM ] # Put mappings for all CM displays here.
# These are DEC-specific, and may need localization
*..Blink = Blinking
*..Inverted+Underline.Bold = ReverseBoldUnderline
*..Inverted+Underline. = UnderlineReverse
*..Underline.Bold = UnderlineBold
*..Inverted.Bold = ReverseBold
*...Bold = Bold
*..Underline = Underline
*..Inverted = Reverse
* = Plain # The font of last resort
# Oracle Report PDF sections
# Three new sections have been added:
# [ PDF ] - Used for font aliasing and Multibyte language support
# [ PDF:Embed ] - Used for Type 1 font embedding
# [ PDF:Subset ] - Used for True Type Font subsetting
[ PDF ]
# This example shows how to rename helvetica font to Courier font
# helvetica = Courier
# You can Alias specific styles of font as below
# helvetica.12..Bold.. = Courier.14....
# "Lucida Bright".12..Bold = "New Century Schoolbook"
# Support for Far Eastern Languages:
# PDF section can be additionally used to enable Multibyte language support
# built into Reports. To use this feature with Adobe (r) Acrobat (c), you
# need to install the Asian font pack available online at the Adobe web site.
# .....SJIS = "HeiseiKakuGo-W5-Acro"
# A Japanese report run with Shift-JIS character set is replaced to
# HeiseiKakuGo-W5-Acro CID font.
arial = Arial
"arial" =Arial
"arial narrow" = "Arial Narrow"
"courier new" = "Courier New"
tahoma = Tahoma
"microsoft sans serif" = "Microsoft Sans Serif"
"ms sans serif" = "MS Sans Serif"
"times new roman" = "Times New Roman"
[ PDF:Embed ]
# This example shows how to embed Type 1 helvetica font into the PDF file:
# helvetica = "helvetica.afm helvetica.pfa"
# You need to specify the .afm file before the .pfa file.
# The font files must exist in one of the folders specified in REPORTS_PATH.
[ PDF:Subset ]
# This example shows how to subset Arial True Type font into the PDF file:
# helvetica = "Arial.ttf"
# The True Type font files must exist in any one of the folders specified in
# REPORTS_PATH.
helvetica..Oblique.Medium = "Sadvocra.ttf"
helvetica..Plain.Medium = "Sadc128d.ttf"
helvetica...Bold = "CarolinaBar-B39-25F2-Normal.ttf"
# NOTES ON PRECEDENCE OF PDF SECTIONS:
# If you have entries for a same font in many PDF sections, then Font
# Aliasing entry will take precedence over Font Embedding entry. Entries
# in Font Embedding will take precedence over the entries in Font Subsetting
# section.
# Generic entries for a font must follow more specific entries for the same
# font. For instance, if you want to subset helvetica Plain, helvetica Bold,
# helvetica Italic and helvetica Bold-Italic fonts, your entries must be:
# [ PDF:Subset ]
# helvetica..Italic.Bold.. = "Arialbi.ttf"
# helvetica...Bold.. = "Arialb.ttf"
# helvetica..Italic... = "Ariali.ttf"
# helvetica..... = "Arial.ttf"
# If helvetica..... entry appears in the top of the list, all the styles of
# helvetica font in the layout will be subset as helvetica Plain font.
uiprint.txt
# This is the printer configuration file.
# The format for entries in this file is:
# <OSName>:<Type>:<Version>:<Long Name>:<Description File>:
# The first field is the name of the printer. It is the name you give
# to lpq.
# The second field is the type of driver to be used for the printer.
# Currently, "PostScript" and "ASCII" are the only types of driver for
# printers supported for now. But in future we may be supporting
# drivers for other printer types.
# The third field is the version of the type of printer driver. It's 1
# or 2 for all PostScript printers; or 1 for ASCII printers.
# The fourth field is a long description of the printer. This will be
# presented to the user in the "Choose Printer" dialog window.
# The fifth field is the printer description file to be used. For
# PostScript printers it is the PPD file of the printer. (This field is
# currently unused for ASCII printers.)
# You can use default.ppd for the description file if you don't have a
# PPD file for the printer, but it's best to use the correct PPD file
# for the printer.
# You must fill in at least the first two fields (printer name and
# type). If the version is empty, it defaults to "1"; if the long name
# or description are empty, they will default to empty strings. A
# version of 1 or an empty long name is fine, but, for PostScript
# printers, you must fill in the description file name.
# You don't have to update this file to use any printer. The printer
# chooser interface let's you select a printer and driver at run time,
# as well as associate a printer description file to the printer. You
# should list all printers accessible to users here, however, to
# simplify selecting a printer.
# The first entry in this file will be used as the default printer, if
# no printer was selected in the operating system. (For Unix, the
# following environment variables will be used in turn to get the
# default printer's name:
# TK2_PRINTER
# ORACLE_PRINTER
# PRINTER
# For other platforms, see the Installation and User's Guide for your OS
# for information on setting the default printer.)
# WARNING: Do not define multiple entries for the same printer by the
# same name. Selecting a printer with multiple entries will always result
# in the first entry being selected. Instead, see if your OS allows you
# to create an alias for the printer, and use an alias for the second type.
# The following are examples; replace them with printers accessible from
# this machine.
# hqunx15:PostScript:1:The really slow printer on 12th floor:dcln03r1.ppd:
# hqdev2_pos:PostScript:1:The fast ScriptPrinter in 1281:dclps321.ppd:
# hqunx106:ASCII:1:LNO printer in the 11th floor printer room:none:
# hqdev9:PostScript:1:Bogus printer for Reports ASCII QA:default.ppd:
# hqunx121:PostScript:1:APO printer in 500OP for NLS QA:ok800lt1.ppd:
# --- Note that the following two printers are aliases for the same
# --- physical printer, with different names for different types:
# tk2hp4m:PCL:5:HP printer in 771 for testing PCL:ui4.hpd:
# tk2bw1ps:PostScript:1:HP printer in 771 for testing PS:hp4mp6_1.ppd:
# Not A Printer:ASCII:1:Configure your uiprint.txt file:none:
fontprinter:PostScript:1:printer for fonting fixes:default.ppd:
datap462.ppd
*PPD-Adobe: "4.0"
*% Adobe Systems PostScript(R) Printer Description File
*% Copyright 1987-1992 Adobe Systems Incorporated.
*% All Rights Reserved.
*% Permission is granted for redistribution of this file as
*% long as this copyright notice is intact and the contents
*% of the file is not altered in any way from its original form.
*% End of Copyright statement
*FormatVersion: "4.0"
*FileVersion: "3.1"
*PCFileName: "DATAP462.PPD"
*LanguageVersion: English
*Product: "(Dataproducts LZR 2665)"
*PSVersion: "(46.2) 1"
*ModelName: "Dataproducts LZR-2665"
*NickName: "Dataproducts LZR-2665 v46.2"
*% ==== Options and Constraints =====
*OpenGroup: InstallableOptions/Options Installed
OpenUI Option1/Optional Lower Tray: Boolean
*DefaultOption1: False
*Option1 True/Installed: ""
*Option1 False/Not Installed: ""
CloseUI: Option1
*CloseGroup: InstallableOptions
UIConstraints: Option1 False *InputSlot Lower
*% General Information and Defaults ===============
*ColorDevice: False
*DefaultColorSpace: Gray
*FreeVM: "178744"
*LanguageLevel: "1"
*VariablePaperSize: False
*FileSystem: False
*Throughput: "26"
*Password: "0"
*ExitServer: "
count 0 eq { % is the password on the stack?
true
dup % potential password
statusdict /checkpassword get exec not
} ifelse
{ % if no password or not valid
(WARNING : Cannot perform the exitserver command.) =
(Password supplied is not valid.) =
(Please contact the author of this software.) = flush
quit
} if
serverdict /exitserver get exec
*End
*Reset: "
count 0 eq { % is the password on the stack?
true
dup % potential password
statusdict /checkpassword get exec not
} ifelse
{ % if no password or not valid
(WARNING : Cannot reset printer.) =
(Password supplied is not valid.) =
(Please contact the author of this software.) = flush
quit
} if
serverdict /exitserver get exec
systemdict /quit get exec
(WARNING : Printer Reset Failed.) = flush
*End
*DefaultResolution: 300dpi
*?Resolution: "
save
initgraphics
0 0 moveto currentpoint matrix defaultmatrix transform
0 72 lineto currentpoint matrix defaultmatrix transform
3 -1 roll sub dup mul
3 1 roll exch sub dup mul
add sqrt round cvi
( ) cvs print (dpi) = flush
restore
*End
*% Halftone Information ===============
*ScreenFreq: "50.0"
*ScreenAngle: "54.0"
*DefaultScreenProc: Dot
*ScreenProc Dot: " {dup mul exch dup mul add sqrt 1 exch sub } "
*ScreenProc Line: "{ pop }"
*ScreenProc Ellipse: "
{ dup 5 mul 8 div mul exch dup mul exch add sqrt 1 exch sub }"
*End
*DefaultTransfer: Null
*Transfer Null: "{ }"
*Transfer Null.Inverse: "{ 1 exch sub }"
*% Paper Handling ===================
*% Use these entries to set paper size most of the time, unless there is
*% specific reason to use PageRegion.
*OpenUI *PageSize: PickOne
*OrderDependency: 30 AnySetup *PageSize
*DefaultPageSize: Letter
*PageSize Letter: "statusdict /lettertray get exec letterR"
*PageSize Letter.Transverse: "statusdict /lettertray get exec letter"
*PageSize Legal: "statusdict /legaltray get exec"
*PageSize Ledger: "statusdict /ledgertray get exec"
*PageSize Statement: "statusdict /statementtray get exec"
*PageSize Tabloid: "statusdict /11x17tray get exec"
*PageSize A3: "statusdict /a3tray get exec"
*PageSize A4: "statusdict /a4tray get exec a4R"
*PageSize A4.Transverse: "statusdict /a4tray get exec a4"
*PageSize A5: "statusdict /a5tray get exec"
*PageSize B4: "statusdict /b4tray get exec"
*PageSize B5: "statusdict /b5tray get exec b5R"
*PageSize B5.Transverse: "statusdict /b5tray get exec b5"
*CloseUI: *PageSize
*% These entries will set up the frame buffer. Usually used with manual feed.
*OpenUI *PageRegion: PickOne
*OrderDependency: 40 AnySetup *PageRegion
*DefaultPageRegion: Letter
*PageRegion Letter: "letterR"
*PageRegion Letter.Transverse: "letter"
*PageRegion Legal: "legal"
*PageRegion Ledger: "ledger"
*PageRegion Tabloid: "11x17"
*PageRegion A3: "a3"
*PageRegion A4: "a4R"
*PageRegion A4.Transverse: "a4"
*PageRegion A5: "a5"
*PageRegion B4: "b4"
*PageRegion B5: "b5R"
*PageRegion B5.Transverse: "b5"
*PageRegion Statement: "statement"
*CloseUI: *PageRegion
*% The following entries provide information about specific paper keywords.
*DefaultImageableArea: Letter
*ImageableArea Letter: "20 16 591 775 "
*ImageableArea Letter.Transverse: "18 19 593 773 "
*ImageableArea Legal: "18 19 593 990 "
*ImageableArea Ledger: "18 16 1205 775 "
*ImageableArea Tabloid: "16 19 775 1206 "
*ImageableArea A3: "18 21 823 1170 "
*ImageableArea A4: "18 18 576 823 "
*ImageableArea A4.Transverse: "18 19 577 823 "
*ImageableArea A5: "18 19 401 577 "
*ImageableArea B4: "19 15 709 1017 "
*ImageableArea B5: "20 19 495 709 "
*ImageableArea B5.Transverse: "20 19 495 709 "
*ImageableArea Statement: "22 19 374 594 "
*?ImageableArea: "
save
/cvp {( ) cvs print ( ) print } bind def
/upperright {10000 mul floor 10000 div} bind def
/lowerleft {10000 mul ceiling 10000 div} bind def
newpath clippath pathbbox
4 -2 roll exch 2 {lowerleft cvp} repeat
exch 2 {upperright cvp} repeat flush
restore
*End
*% These provide the physical dimensions of the paper (by keyword)
*DefaultPaperDimension: Letter
*PaperDimension Letter: "612 792"
*PaperDimension Letter.Transverse: "612 792"
*PaperDimension Legal: "612 1008"
*PaperDimension Ledger: "1224 792"
*PaperDimension Tabloid: "792 1224"
*PaperDimension A3: "842 1191"
*PaperDimension A4: "595 842"
*PaperDimension A4.Transverse: "595 842"
*PaperDimension A5: "420 595"
*PaperDimension B4: "729 1032"
*PaperDimension B5: "516 729"
*PaperDimension B5.Transverse: "516 729"
*PaperDimension Statement: "396 612"
*RequiresPageRegion All: True
*OpenUI *InputSlot: PickOne
*OrderDependency: 20 AnySetup *InputSlot
*DefaultInputSlot: Upper
*InputSlot Upper: "0 statusdict /setpapertray get exec"
*InputSlot Lower: "1 statusdict /setpapertray get exec"
*?InputSlot: "
save
[ (Upper) (Lower) ] statusdict /papertray get exec
(get exec) stopped ( pop pop (Unknown)} if = flush
restore
*End
*CloseUI: *InputSlot
*OpenUI *ManualFeed: Boolean
*OrderDependency: 20 AnySetup *ManualFeed
*DefaultManualFeed: False
*ManualFeed True: "statusdict /manualfeed true put"
*ManualFeed False: "statusdict /manualfeed false put"
*?ManualFeed: "
save
statusdict /manualfeed get {(True)}{(False)}ifelse = flush
restore
*End
*CloseUI: *ManualFeed
*DefaultOutputOrder: Reverse
*% Font Information =====================
*% This datap462.ppd is provided by fontsolutions.tar
*DefaultFont: Courier
*Font ArialMT: Standard "(001.004)" Standard ROM
*Font Arial-ItalicMT: Standard "(001.004)" Standard ROM
*Font Arial-BoldMT: Standard "(001.004)" Standard ROM
*Font Arial-BoldItalicMT: Standard "(001.004)" Standard ROM
*Font ArialNarrow: Standard "(001.004)" Standard ROM
*Font ArialNarrow-Italic: Standard "(001.004)" Standard ROM
*Font ArialNarrow-Bold: Standard "(001.004)" Standard ROM
*Font ArialNarrow-BoldItalic: Standard "(001.004)" Standard ROM
*Font CourierNewMT: Standard "(001.004)" Standard ROM
*Font CourierNew-ItalicMT: Standard "(001.004)" Standard ROM
*Font CourierNew-BoldMT: Standard "(001.004)" Standard ROM
*Font CourierNew-BoldItalicMT: Standard "(001.004)" Standard ROM
*Font Courier: Standard "(001.004)" Standard ROM
*Font Courier-Bold: Standard "(001.001)" Standard ROM
*Font Courier-BoldOblique: Standard "(001.001)" Standard ROM
*Font Courier-Oblique: Standard "(001.001)" Standard ROM
*Font Helvetica: Standard "(001.001)" Standard ROM
*Font Helvetica-Bold: Standard "(001.001)" Standard ROM
*Font Helvetica-BoldOblique: Standard "(001.001)" Standard ROM
*Font Helvetica-Oblique: Standard "(001.001)" Standard ROM
*Font IDAutomationSMICR: Standard "(001.001)" Standard ROM
*Font Symbol: Special "(001.001)" Special ROM
*Font Tahoma: Standard "(001.001)" Standard ROM
*Font Tahoma-Bold: Standard "(001.001)" Standard ROM
*Font Times-Bold: Standard "(001.001)" Standard ROM
*Font Times-BoldItalic: Standard "(001.001)" Standard ROM
*Font Times-Italic: Standard "(001.001)" Standard ROM
*Font Times-Roman: Standard "(001.001)" Standard ROM
*Font TimesNewRomanMT: Standard "(001.001)" Standard ROM
*Font TimesNewRoman-BoldMT: Standard "(001.001)" Standard ROM
*Font TimesNewRoman-BoldItalicMT: Standard "(001.001)" Standard ROM
*Font TimesNewRoman-ItalicMT: Standard "(001.001)" Standard ROM
*?FontQuery: "
save
/str 100 string dup 0 (fonts/) putinterval def
count 1 gt
exch dup str 6 94 getinterval cvs
(/) print print (:) print
FontDirectory exch known
{(Yes)}{(No)} ifelse =
{exit} ifelse
}bind loop
(*) = flush
restore
*End
*?FontList: "
FontDirectory { pop == } bind forall flush
(*) = flush
*End
*% Printer Messages (verbatim from printer):
*Message: "%%[ exitserver: permanent state may be changed ]%%"
*Message: "%%[ Flushing: rest of job (to end-of-file) will be ignored ]%%"
*Message: "\FontName\ not found, using Courier"
*% Status (format: %%[ status: <one of these> ]%% )
*Status: "idle"
*Status: "busy"
*Status: "waiting"
*Status: "printing"
*Status: "warming up"
*Status: "PrinterError: BD check"
*Status: "PrinterError: Paper jam"
*Status: "PrinterError: Replace toner bag"
*Status: "PrinterError: Warming up"
*Status: "PrinterError: Timing error"
*Status: "PrinterError: Fuser check"
*Status: "PrinterError: Cover opened"
*Status: "PrinterError: Toner empty"
*Status: "PrinterError: Empty & reset output bin(s)"
*Status: "PrinterError: Sorter or jogger error"
*Status: "PrinterError: Scanner check"
*% Input Sources (format: %%[ status: <stat>; source: <one of these> ]%% )
*Source: "serial9"
*Source: "serial25"
*Source: "AppleTalk"
*Source: "Centronics"
*% Printer Error (format: %%[ PrinterError: <one of these> ]%%)
*PrinterError: "BD check"
*PrinterError: "Paper jam"
*PrinterError: "Replace toner bag"
*PrinterError: "Warming up"
*PrinterError: "Timing error"
*PrinterError: "Fuser check"
*PrinterError: "Cover opened"
*PrinterError: "Toner empty"
*PrinterError: "Empty & reset output bin(s)"
*PrinterError: "Sorter or jogger error"
*PrinterError: "Scanner check"
*%DeviceAdjustMatrix: "[1 0 0 1 0 0]"
*% Color Separation Information =====================
*DefaultColorSep: ProcessBlack.60lpi.300dpi/60 lpi / 300 dpi
*InkName: ProcessBlack/Process Black
*InkName: CustomColor/Custom Color
*InkName: ProcessCyan/Process Cyan
*InkName: ProcessMagenta/Process Magenta
*InkName: ProcessYellow/Process Yellow
*% For 60 lpi / 300 dpi =====================================================
*ColorSepScreenAngle ProcessBlack.60lpi.300dpi/60 lpi / 300 dpi: "45"
*ColorSepScreenAngle CustomColor.60lpi.300dpi/60 lpi / 300 dpi: "45"
*ColorSepScreenAngle ProcessCyan.60lpi.300dpi/60 lpi / 300 dpi: "15"
*ColorSepScreenAngle ProcessMagenta.60lpi.300dpi/60 lpi / 300 dpi: "75"
*ColorSepScreenAngle ProcessYellow.60lpi.300dpi/60 lpi / 300 dpi: "0"
*ColorSepScreenFreq ProcessBlack.60lpi.300dpi/60 lpi / 300 dpi: "60"
*ColorSepScreenFreq CustomColor.60lpi.300dpi/60 lpi / 300 dpi: "60"
*ColorSepScreenFreq ProcessCyan.60lpi.300dpi/60 lpi / 300 dpi: "60"
*ColorSepScreenFreq ProcessMagenta.60lpi.300dpi/60 lpi / 300 dpi: "60"
*ColorSepScreenFreq ProcessYellow.60lpi.300dpi/60 lpi / 300 dpi: "60"
*% For 53 lpi / 300 dpi =====================================================
*ColorSepScreenAngle ProcessBlack.53lpi.300dpi/53 lpi / 300 dpi: "45.0"
*ColorSepScreenAngle CustomColor.53lpi.300dpi/53 lpi / 300 dpi: "45.0"
*ColorSepScreenAngle ProcessCyan.53lpi.300dpi/53 lpi / 300 dpi: "71.5651"
*ColorSepScreenAngle ProcessMagenta.53lpi.300dpi/53 lpi / 300 dpi: "18.4349"
*ColorSepScreenAngle ProcessYellow.53lpi.300dpi/53 lpi / 300 dpi: "0.0"
*ColorSepScreenFreq ProcessBlack.53lpi.300dpi/53 lpi / 300 dpi: "53.033"
*ColorSepScreenFreq CustomColor.53lpi.300dpi/53 lpi / 300 dpi: "53.033"
*ColorSepScreenFreq ProcessCyan.53lpi.300dpi/53 lpi / 300 dpi: "47.4342"
*ColorSepScreenFreq ProcessMagenta.53lpi.300dpi/53 lpi / 300 dpi: "47.4342"
*ColorSepScreenFreq ProcessYellow.53lpi.300dpi/53 lpi / 300 dpi: "50.0"
*% For "Dataproducts LZR 2665" version 46.2
*% Produced by "GETapd.ps" version 2.0 edit 47
*% Converted to meet 4.0 specification
*% Last Edit Date: Sep 15 1992
*% The byte count of this file should be exactly 011228 or 011572
*% depending on the filesystem it resides in.
*% end of PPD file for Dataproducts LZR 2665If you want to make platform independent use of fonts, you have to use the family, such as sans serif.
Arial is owned by monotype (http://monotype.com/). You have to contact them if you wish to redistribute it with your application. They also might have a suitable version that renders nicely under linux.
Pete -
Font copperplate gothic bold is not shown correctly in my webssite
index page font= copperplate gothic bold is not shown in firefox.
In IE it functions okayDoesn't look like I have a ttf available, hmm...
~ fc-list | grep -i 'DejaVu Sans Mono'
/usr/share/fonts/t1-dejavu-ib/DejaVuSansMono-Bold.pfb: DejaVu Sans Mono:style=Bold
/usr/share/fonts/t1-dejavu-ib/DejaVuSansMono-Oblique.pfb: DejaVu Sans Mono:style=Oblique
/usr/share/fonts/t1-dejavu-ib/DejaVuSansMono-BoldOblique.pfb: DejaVu Sans Mono:style=Bold Oblique
/usr/share/fonts/t1-dejavu-ib/DejaVuSansMono.pfb: DejaVu Sans Mono:style=Regular -
Some fonts are not shown correctly in LabVIEW 2012
I found a bug related with fonts in LabVIEW2012 f3 KR.
- When I select NI7SEG in font selection dialog, right font is not shown in the example box.
- Draw text at point.vi shows same problem for some fonts while other fonts are working.
I reported it to Korean NI. As far as I know, this was not reported in previous versions and I couldn't find any related documents in Google.
So, here I would like to know whether it is related with only Korean version. Please let me know if English version is OK.
* OS: Windows 7 32bit KRJust now, I installed LabVIEW 2012 f3 (32-bit, English) and checked for the issue. But the font(NI7SEG) was not shown properly in VI either.
- Both of Korea and English version of LabVIEW 2012 on Win 7 Korea OS shows wrong results. It is same on 64-bit OS.
- LabVIEW 2010 but on same PC shows correct fonts.
Is there a limit of number of fonts in LabVIEW? There are more than 100 fonts are shown in the "Selection Font" dialog and I can divide them into 3 groups by sequential order. I find that all fonts in the 3rd group are not applied correctly.
(1st group)
Arial Unicode MS...
Bookshelf Symbol 3....
Windings 3
(2nd group)
@Arial Unicode MS...
@Terminal
(3rd group)
Arial...
Consolas...
Courier...
Licida Console...
NI7SEG...
Verdana -
IPC/VC: Knowledgebase/KB of ECC is not shown in CRM
Hi,
we would like to use the Variant Configuration in CRM.
Today we are using already the IPC in a standalone environment with an external system (IPC 5.0, the external system is using the IPC in the Java environment of ERP). From the same ECC System we would like to download now the knowledge bases to reuse them in CRM 7.0. All knowledge bases and runtime environments are already available. When I download the object SCE (with certain filters), I can see all those entries in table COMM_CFGKB in CRM.
Anyhow, when checking the material in CRM (e.g. commpr01 or WebUI), no knowledge base is shown!
The table COMM_CFGKB has exactly the same entries as ECC (Active = T, KB Usage 10, KBOBJNAME and Version filled etc.), but anyhow it is not shown at all in CRM. As these knowledge bases are very huge, I have tested also a very small and easy one. This one is getting downloaded the same way and has the same entries in table COMM_CFGKB and it is also visible in commpr01.
So my assumption is that the other KBs are not 100% correct. When checking them in ECC (cu36) I get many warnings and errors. Anyhow, they were downloaded to CRM (but won`t be shown). Business says that these warnings/errors are OK and that the external system which uses the IPC in ECC is not having any problems.
Question: is there any chance of using a KB in CRM which has warning/errors when it was generated in ECC?
Is there any chance of manipulating the KB before it gets imported into CRM. I have found Note 1044682 which explains a BADI.
Which tables/fields do we have to manipulate so we are able to use the KB in CRM.
As mentioned: business is aware of those errors and excepts that there might be a crash in the IPC for certain combinations.
Thx
GuidoHi Christophe,
OK, I think I understand your suggestion: you use the same IPC with your CRM as well as with the ECC system. So in CRM you just maintain the URL and a user in XCM to the "same" IPC. You mentioned that we need to download anyway the SCE. This is somehow logical as this is the base connected to CRM, but what is not clear to me is the fact, that if the SCE KB is used via ECC all SAP R/3 fields are available (like VBTYPE of the sales order where you have values like B or C). In CRM we use the same SCE KB but here these fields are not availble as the sales order transaction customizing in CRM does not contain such a field. Where is the logical link between the values which are available in IPC and the SCE?
Thx
Guido -
Voice memos sync not shown in iTunes
I am trying to sync my voice memos to iTunes a couple of times. They are not shown. I haven't updated my iPhone 5s to the latest software yet. It's still running iOS 7; my iTunes was updated though. Does anyone have a solution for this?
Thank you!!!You need to open iTunes on your computer. Then select music library from the left-hand. Then in the search window on the top right of the screen type in voice memo . The voice memo should now appear in the list is available music in the middle of the iTunes screen
-
Yosemite 10.10.1: Finder/CIFS mount problem: wrong folder count/folders not shown @samba shares
Hello to all,
we have several MacBook Pro (15" MBP Retina 2012/13"MBP Retina 2014) running. After upgrading to Yosemite 10.10.1 we had one nightmare after the other.
Most problems could be solved with 3rd party software upgrades but there are several problems with the operating system itselve which can not really be called a professional productive system at the moment...
Ok., one thing after the other...here is one of our biggest problems:
After upgrading from Mavericks or Mountain Lion to Yosemite 10.10.1 the CIFS/SMB mounts to our samba 3.x servers, running on Ubuntu Linux LTS 12.04 makes trouble. We could mount the server shares but after browsing with the Finder the beach ball occures and the Finder hangs forever. Sometimes we could not refresh the Finder, killing the process ended in a complete hang-up of the system which ended in a switch off death blow. This is not amusing because we have 30Tb of customer data there, which has to be worked out.
We heard about the SMB3 protocol which will be used per default in Yosemite and so we decided after some testings to upgrate our Ubuntu servers to the latest LSF 14.04. release with samba 4.1.6 installed. There was no message from Apple for this SMB protocol release upgrade, never heard something related to Yosemite (Why?).
Ok, after these server upgrades and disabling most of the Spotlight functions the performance to the CIFS shares was a little bit better as before but now we have another problem with the Finder...if you browse to the shares there are folders missing which have lots of files in it. For example there is a folder with 60 subfolders and 3562 files on the first level in it, the Finder shows 220 files and 15 folders. The Terminal shows a different count with "find . -maxdepth 1 -type d | wc -l" or "find . -maxdepth 1 -type f | wc -l" but there is also a difference to the original file and folder count. It doesn`t matter if the clients are connected via WiFi or Gigabit Ethernet. We have no access problems. We have the same behavior if we set the files and folders to 0777 permissions on the servers. The deletion of the preferences files of the users on the MacBooks does not solve the problem. If we use the "Go To Folder" option and type the path to a folder which is not shown in the Finder you get an result or not. But it is also possible that the result is not correct and there are also still files or subfolders missing.
In my opinion this is a timeout problem and a "special SMB3 protocol interpretation" which is buggy. We have one hint found in /var/log/system.log:
"Jan 23 14:35:49 wsosx33.clients.getcom.de KernelEventAgent[69]: tid 54485244 type 'smbfs', mounted on '/Volumes/customersdata2015', from '//x144067:@srvlxp013.servers.getcom.de/customersdata2015', not responding"
We had no problems with Mavericks at all, we still have no problems with Windows 7 Pro/Ultimate, Windows 2008R2 (native or virtual) or Linux Mint 17/17.1 clients, neither with samba 3.x nor with our actual environment and different newer samba releases.
We believe that this is a big bug in Yosemite, but we cannot go back to Mavericks because of incompatible TimeCapsule backups. Our workarround at the moment is that we have installed Linux Mint on our MacBooks to get 80% of our daily jobs done, rest has to be done with Windows 7 installed over virtualbox @Linux.
We have no clue at the moment how to solve this problem, the samba logs do not give any hint. The access from other operating systems is perfect and very fast, but not with Yosemite. We checked different tips found in the internet but nothing helped.
Does anybody has another idea to get Yosemite working or should we keep Linux Mint until Apple will provide a CIFS/SMB patch and going on with our workaround solution, which is productive at the moment ??? Our staff is not amused and wants one solution and not this workaround with two operating system. We have to decide wether we wait until Apple will get this fixed or we have to switch to Microsoft Windows (which is a No Go for me, but I will not be asked...).
Thanks in advance
C.Hi William,
thank you for your response.
As you can read in my post I talked about CIFS/SMB.
It makes no difference if we mount the share over CIFS or SMB.
Folders with lots of files will not be shown even if we use SMB3 or an older protocol.
As mentioned I believe this is a timeout problem.
Does anybody know how the CIFS/SMB timeout setting in Yosemite could be changed?
Kind regards
C. -
In my Apple Macbook Air, most of the USB Flash/Thumb Drives are not shown in the Finder Window. Only a few Brands of USB /Flash Thumb Drives are shown or compatible or shown in the Finder. How do I use any Flash/Thumb Drive with my Apple MacAir?
Yes, junker thumb drives pour like rain in the market.
Which makes are working on your Air, and which arent?
Stick to Sandisk and a couple of other reliable mfg. of memory sticks -
Reporting tab is not shown in the console
hi everyone
the reporting tab is not shown in the service manager console, the topology i am using is 2 servers [one for DW and the other for management server] both servers have their SQL server installed on each one, could you please tell me how i can start to get
this working or the steps i have to follow ?? isn't supposed to be working out of the box ? i have checked reporting services and they are runningProbably your report server is not pointing to the DWDATAMART database, try login to:
http://YourDWDatabase/Reports/Pages/Folder.aspx?ItemPath=%2fSystemCenter%2fServiceManager&ViewMode=List
click on DWDATAMART Connection, under connection string, do you see your DWDATAMART DB name and server name?
Antoine AL Ibry -
Text in PO(text tab in header & item) is not shown in the Print Preview
Hi Guys,
I face a problem in ME23N.Text maintained in Purchase Orders (text tab in header & item) is not shown in the Print Preview.
Can you guys help.Do I need to write a subroutine pool for this.
<<text removed by moderator>>
Regards,
Rajiv
Edited by: Matt on Nov 12, 2008 1:20 PMHi ,
Use bapi bapi_po_getdetail .
CALL FUNCTION 'BAPI_PO_GETDETAIL'
EXPORTING
purchaseorder = is_ekko-ebeln
item_texts = c_x
header_texts = c_x
TABLES
po_header_texts = it_header_text
po_item_texts = it_item_text.
Regards
Neetesh -
Approved and published items are not shown in the catalog search
Hello all,
We are implementing SRM 4.0 SSP scenario .
To support shopping of EBP we are also implementing CCM 2.0 as an add on.
Please note CCM and EBP are on same client and CAT & CSE are also on the same client.
No XI is involved. The catalog scheme was uploaded as CSV 2.0. The items for the catalog was created manually in CAT.
Although the item has the status "approved" and the procurement catalog which is also the master catalog was published successfully the item is not shown after searching by CSE in EBP. Also the categories of the scheme are not shown in the catalog search.
Do i have to approve the categories too and if yes can you explain me how to do this?
I think you see that I'm a newbie at srm and ccm and this problem is probably no real problem but I have not found any similar topics in the forum. So please can you help.
Thanks a lot for your help.
Best regards,
BerndBernd: the reason I asked about views is that you don't have any error messages. This might indicate that (a) you have no items in the view, or (b) there's something wrong with view-role-user assignment.
To check for (a), please go to the published procurement catalog, and go to Views tab. Check that your View is Active. Click on your View ID link to display view details. You should see a list of characteristics assigned to your view in Assign Characteristics sub-tab (the list should not be blank!). Go to Assign Items sub-tab. Navigate in your schema to find items that are supposed to be assigned to your view. You should see "Yes" in the "Assigned" column for those products. If you don't, then you simply don't have any items in your view.
Another thing I'd like you to check: when the user calls your procurement catalog for search, do you see the name of the catalog displayed just below the drop-down "Select Categories Hierarchically"?
Cheers,
Serguei -
Hi,
I have copied these problem on you site, as I could explain better then what they did, wich my problem remain the same as they have. And part me explaining what is really happen to my Laptop.
''Mozilla/Firefox 4 will not SHOW on my computer SCREEN.
Firefox won't load onto my computer. I have Windows 7, and each time I try to run the program to install it, it tells me I have another version still waiting to be installed that requires my computer to reboot. When I check "yes" to reboot, my computer reboots but still no Firefox. When I try to uninstall the the old Mozilla program from my Control Panels, there is no Mozilla files or programs listed not in my list of programs but when I go directly to the Windows File on the C: Drive, there's a Mozilla program file there. WHen I go into that file check, I attempt to open the uninstall program. I get an error message that says something to the effect of: "the version Mozilla on this computer is not compatable with my OS." Something about it being and 86bit program. My Firefox 3.6 worked fine 2 days ago. What's wrong??? ''
'''Firefox 4 using huge amounts of RAM on sites with Java scripts
I have been observing Firefox using huge amount of RAM when I am on sites that use Java Scripts to rotate images. I have tried a couple of different sites and have monitored the RAM usage. With Java script enabled Firefox 4 continues to grow its RAM usage by about 10MB a minute. I have had the usage hit as high as 1.5GB. As a comparison I have monitored the same sites in Internet explorer and have not seen the same issue. - Just to eliminate a site issue.
Turning off Java Script solves the issue and eventually frees the RAM.
I am using XP Pro, 3 GB RAM. '''''
My experince with Mozilla Firefox:
Here what really happen when I install the Mozilla Firebox on my La[top you can see the file is there but when I click the program to open its does not shown on the screen but when I check with WTM (Windows Task Manager) its shows that is ON and you can only witness the laptop going very slow and I have to reboot it, and I can not install any other Mozilla :( because of the same problem and all the above.
I really need Mozilla to work as soon as possible due to important deadlines I have pendent, and i can only use Chrome but is not my ideal program. Can you help me , please ?????
Thank you
Vitor MendesIf it opens in safe mode, you may have a problematic add-on. Try the procedure in the [[Troubleshooting extensions and themes]] article.
-
Available QTY is not shown in Production Order for SemiFinished Product?
Hi
In Production Order Available Qty value is not shown for SemiFinished product ( Stock is there), but it showing the Available for other rawmaterials in same Prdn. ordr..
The SemiFinished product is manufactured and its having lot of stocks ..while i am calling this SemiFinished product in other Production order the available qty is not shown.. so how come the end user comes to know that availlable..
GiriHi Jey
I will explain clearly so u can come what is hapening For Ex: Item ABC having child item A,B & C.
when calling the BOM of ABC in Prodn.order its showing the available of A, B & C... But after the production over for the Semifinished product it increases the stock.
When i am calling this Semifinished Product in other Produciton Order For Ex: Item AZ having Child item ABC & XYZ.
In this Scenerio it has to show the Available of item ABC whic is semifinished product its not showing,but in the same Production order it showing the available for Other item XYZ which is purchased one .. So this is the nature of SAP or i am doing any wrong....
Giri -
Segment field is not shown in profit center master data
Hi,
When i activated New GL ,but the segment field is not shown in profit center master data. How can i make the field shown ?
Thanks.After activating the New GL have you defined the segment? First define the segment under Enterprise Structure and in Fin.Acctg Global settings(New)-Legers-Display scenarios for General Ledger Accounting, you need to create new entries for FIN_PCA & FIN_SEG.
Hope this helps you. -
Crystal report not shown after application idle time
i have a web page which uses around 10 session variables to store values on a button click.and after assign session values Response.Redirect("~/url",false); to a a page which contains crystal report viewer.and report should show those session values.after keeping the application idle for 45 mins i click on the button which assign session values.then it's redirecting to the report page but the report is not shown.it shows a empty page and no errors shown(only happens application is idle for nearly 45 mins other wise works fine)
i'm using iis 7
in the web.config i have set sessionState timeout="60" and application pool idle time out to 60 mins.
any idea why this happensMake sure you are on SP 8
Make sure you are using .Close and .Dispose on your report objects as you get done with them.
What OS? (2003, 2008, 2012)
Provide more info on the following:
The problem is that the Crystal Report Viewer does not load after a few hours.
What does that mean? Errors? Warnings? Behavior? Symptoms?
- Ludek
Senior Support Engineer AGS Product Support, Global Support Center Canada
Follow us on Twitter
Maybe you are looking for
-
All: Is it possible to enforce data security filters when a report would need to be delivered to multiple users with individual data visibility? These users will not log in to the OBIEE 11g system and hence the user names (accounts) will not be prese
-
How do I remove plugin-container.exe safely and be sure it doesn't return?
plugin-container.exe keeps running in my Windows task manager slowing or sometimes freezing my computer. How do I eliminate this problem? I am running Firefox 4.0.1., which I will have to stay with for now as the update will not accept my Logitech pr
-
Premiere Pro Freezes mac while rendering Fast Color Corrector & Rgb curves
I am having a problem that is impacting our business. We are doing commercials that we are doing color correction of the subject using Fast Color Corrector and RGB curves. When these effects are added to the sequenced video, the performance of the Ma
-
My keyboard does not type the letter p or the number 0 in portrait/vertical position. And when I use the horizontal keyboard from time to time all functions on the bottom row do not work at all like the space bar, return key, etc. It has become a bit
-
Audigy Plat xp issues with SPDIF out
I recently did an XP pro reload and reinstalled the drivers for my audigy platinum with the results of lossing my spdif output to my reciever. Any suggestion?