QLLC to LAN convertion

Hello Forum
we are trying to establish a connection between 2 PUs and the M/F. The two PUs are actually two controllers inside an IBM 400. The IBM 400 is connected to a cisco with an x25 line. The M/F is connected to the ethernet side of the cisco.
So we need to implement a qllc to llc2 media convertion. The problem here is that both PUs use the same local x25 address since they come out of the same x25 line. So, how can we distinguish between these two on the x25 map qllc statement?
If we had only one PU then the configuration would be obvious:
x25 address 111
x25 map qllc 4000.0000.0002 222
qllc dlsw vmac 4000.0000.0002 10 partner 4000.0000.0001 (for example).
But what can we do for the second PU?
Regards, Apostolos.

The following document has a configuration example which is similar to the scenario that you are trying to configure. Hope this document will be useful to you.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/ibm_c/bcprt2/bcddlsw.htm

Similar Messages

Connect ni elvis ii with computer through LAN

hiiiiiii
has anyone tried to interface ni elvis ii board with computer through a usb to lan converter ?????
i am using a ni elvis ii board with emona datex and want to access it through LAN ....is it possible ??

Have you installed the ELVISmx/DAQmx drivers (see links below)?
http://joule.ni.com/nidu/cds/view/p/id/1047/lang/en
http://joule.ni.com/nidu/cds/view/p/id/3811/lang/en
James K.
National Instruments
Applications Engineer

USB Ethernet - manual configuration

Hello all,
I have a usb to ethernet adapter that I would like to use but can't seem to get to to work. I'm using an imac with Leopard and I've included some output below:
en0: flags=8822<BROADCAST,SMART,SIMPLEX,MULTICAST> mtu 1500
ether 00:1f:f3:4d:f3:12
media: autoselect status: inactive
supported media: autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,hw-loopback> 10baseT/UTP <full-duplex,flow-control> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,hw-loopback> 100baseTX <full-duplex,flow-control> 1000baseT <full-duplex> 1000baseT <full-duplex,hw-loopback> 1000baseT <full-duplex,flow-control> none
fw0: flags=8822<BROADCAST,SMART,SIMPLEX,MULTICAST> mtu 4078
From system profiler:
USB To LAN Converte̊:
Version: 1.01
Bus Power (mA):500
Speed: Up to 12 Mb/sec
Manufacturer: ADMtek
Product ID: 0x8511
Serial Number:0001
Vendor ID: 0x07a6
The adapter I'm using is a TrendNET TU-ET100c and from what i remember from the manufacturer's website it mentioned no drivers were required.
I really just want to assign an ip address to it and bring to interface up.
Any help would be greatly appreciated. Thanks in advance.

Then why not use a switch and router? I'm still a bit confused why the adapter is needed.
In any event I suspect the adapter requires drivers, but I don't see any definitive information other than it's only certified as Windows compatible (except Vista.)
I did find this relevant information regarding USB-Ethernet adapters for Macs: http://www.sustworks.com/site/newsusbethernet.html.

Is there a PORTABLE wireless router that I could travel with to convert hotel LAN lines into wireless signals for my iPad?

I travel regularly to Asia and I have been trying to compile everything I need into my iPad. Unfortunately, most of my hotels do not have wireless in the rooms just an LAN line. Does anyone know of a router (as small as possible) that I can plug an LAN line into that will convert it to a wireless signal I can access with the iPad. What I don’t want is to have to plug the router into a computer and program it forevery different LAN line I encounter. Thoughts???

As the others have said, Airport Express is one option. The catch as Allan said is that the configuration utility doesn't run on the iPad. It is rumored that iOS5 may have the utlity, but that doesn't help you now. If you can wait, then the Airport Express would arguably be the best for the iPad.
If you can't wait, you could get the D-Link DAP-1350. You configure it through a webpage, similar to how you would other home routers.
http://www.dlink.com/products/?pid=DAP-1350
I use the older DWL-G730AP 802.11g version and it's been very good to me for use by my Macbook Pro and iPad1.

The exposed service is in the right lane in BPEL converted from JPD

Hi,
Now I'm working on a project that requires using Fusion to replace the old WLI.
My major job is to convert JPD code in WLI to BPEL in fusion. (The JPD code was developed based on Weblogic Integration 8.1 )
I use a plugin for WebLogic Workshop 8.1 to export JPDs file into BPELs directly.
After some minor changes, the BPEL exported from JPD can be run on the server.
But when I open the BPEL in the visual designer in JDeveloper 11g, I see something strange.
According to my understanding, all exposed services should be placed in the left lane, and all referenced services should be placed into the right lane.
In the exported BPEL composite, when I open the composite.xml file in the visual designer, I can see all the services are in the right places.
But when I click into the BPEL process, I see all service are placed into the right lane, including the exposed service.
This really confuses me.
I tried to read the xml code of composite and BPEL to understand why in BPEL designer, even the exposed service is placed into the right lane. But I haven't got an answer.
I also tried to write a BPEL process by myself, but the exposed service icon cannot be moved to the right lane.
Does anyone has any ideas on this issue? Does oracle has some special way to deal with the code exported from JPD?
Actually, this issue doesn't cause any error in my application. I'm just curious why it happens.
Thanks in advance.

Hi,
I am also doing the same thing what you have done, please help me.
I have used BPEL export utility for exporting my JPDs to BPEL. but it was not a good help, ultimately i m creating a process manually.
the main problem what is the replacement of control(jcx files)
please guide me really it would be great help..
Thanks in advance and hope to hear from you.
my mail id is [email protected]
please send some document if you have...

Can two computers, one USB, other LAN, both use an HP 6310?

Hello,
Might be daft question. I have an HP 6310 all in one which I sometimes use (with difficulty, but does work) with Bluetooth and sometimes with USB. This works fine with one computer that was originally set up with the USB option.
I now have two computers and also a wired (LAN) network through a network switch and the router. Can one computer be set up with the USB software for local printing and the other with Ethernet,and still access the printer? You might ask why I don't just use the LAN on both, but I would just like to know if it is possible. I guess it comes down to whether the setup sends data to the printer to determine which method of connection to use, or is the printer just "dumb" and responds to whichever source is connected to it.
Naturally, as the only user of the network, I would not be using both computers at once for printing to avoid any conflict.
Many new printers are supplied with wireless 802/n capability, but is their a device that can convert the 6310 to wireless 802/n?
Thanks

Hello Meldrewoflewes,
Your Question " Can one computer be set up with the USB software for local printing and the other with Ethernet,and still access the printer? "
Answer : Yes
Regards,
Jabzi
Help the community by marking this post .
Was your question answered? Mark it as an Accepted Solution!
See a great post? Give it a Kudos!
I work for HP
Regards,
Jabzi
Give Kudos to say "thanks" by clicking on the "thumps Up icon" .
Click "Accept as Solution" if it solved your problem, so others can find it.
Although I am an HP employee, I am speaking for myself and not for HP.

How to convert 14GB to 2GB for IMDB upload using FinalCut Pro 7?

Hi,
I am submitting a 12 minute film to festivals and need to convert it from 14GB to around 2GB for best quality results in order to upload it to IMDB so that it could be streamed. I use FinalCut Pro 7 but the compression/export settings for the file are proving to be tricky.
Once I click on Export>Quicktime video
What settings do I choose to have the file be closest to 2GB and have the audio and video synced perfectly, maintaining the good quality of footage shot on Red?
14GB footage specs:
Dimensions: 1920 X 1080.
Codecs: Apple ProRes 422 (HQ), Linear PCM, Timecode
Color profile: HD (1-1-1)
Duration: 11:59
Audio Channels: 2
When I converted it to DVD: I got a DVD .m2v file around 465MB, it that the highest quality I can get for a DVD version?
Also, When I set the settings to 1280 x 720 it resulted in a file size of 275.4MB, when I wanted it to be around 2GB
Please help me asap. I need to get this done today. Thanks alot in advance!

Export a full quality file....FILE>EXPORT>Quicktime Movie. Self contained, sequence settings.
Take that file into COMPRESSOR. Look for the Quicktime 7 Streaming options...choose the H.264 LAN preset. SUBMIT.

Error when converting a 1602i to Autonomous

Hi all... just looking for a little help. I'm trying to convert a 1602i to an Autonomous OS.
I downloaded: ap1g2-k9w7-tar.152-2.JB.tar
Performed the following:
1.) Set PC LAN address to 10.0.0.5
2.) Start TFTP Server and point to folder holding the Autonomous IOS.
3.) Set timeout to 30 seconds
4.) Made a copy of the IOS and renamed it to: "ap3g2-k9w7-tar.default"
5.) Connect AP Ethernet port to Laptop LAN port using a Cat5 cable.
6.) Reset AP power holding the MODE button until the LED blinks Red (~20seconds) and then release the button.
The AP reloaded, and started downloading the IOS from the tftp....
Then I get the following message: (a lot of additional extraction messages I didn't paste)
extracting ap1g2-k9w7-mx.152-2.JB/html/level/15/ap_system-sw_sysconfig.shtml.gz (7145 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/html/level/15/ap_stationview-client.shtml.gz (5554 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/html/level/15/ap_contextmgr_ap.shtml.gz (4774 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/html/level/15/ap_contextmgr_scm.shtml.gz (5294 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/html/level/15/ap_contextmgr_scm-groups.shtml.gz (7511 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/html/level/15/ap_contextmgr_scm_summary.shtml.gz (5061 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/ap1g2-k9w7-mx.152-2.JB (9206971bytes)..........................................................................................................................................................................
Premature end of tar file
ERROR: Problem extracting files from archive.ap:
I've performed this on 2602 without any issues... and we have tried doing the tftp in romon...
ap: tar -xtract tftp://10.0.0.5/ap1g2-k9w7-tar.152-2.JB.tar flash:
Same result... went back to Cisco.com and downloaded the file again and tried again, same result.
Any help would be greatly appreciated.
Rich

I've tried both processes multiple times and have finally gotten to what appears to be the end. However after I reset the AP, I get an error when the AP starts loading the IOS from flash.
xtracting ap1g2-k9w7-mx.152-2.JB/S5.bin (106106 bytes).......................
extracting ap1g2-k9w7-mx.152-2.JB/K2.bin (5830 bytes).
extracting ap1g2-k9w7-mx.152-2.JB/K5.bin (75790 bytes)................
extracting ap1g2-k9w7-mx.152-2.JB/info (277 bytes)
extracting info.ver (277 bytes)ap:
IOS Bootloader - Starting system.
flash is writable
FLASH CHIP: Numonyx Mirrorbit (0089)
Xmodem file system is available.
flashfs[0]: 183 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31997952
flashfs[0]: Bytes used: 10417152
flashfs[0]: Bytes available: 21580800
flashfs[0]: flashfs fsck took 17 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 6c:41:6a:98:05:73
Ethernet speed is 1000 Mb - FULL Duplex
Loading "flash:/ap1g2-k9w7-mx.152-2.JB/ap1g2-k9w7-mx.152-2.JB"...uncompress: Unknown mzip segment type: 2
Error loading "flash:/ap1g2-k9w7-mx.152-2.JB/ap1g2-k9w7-mx.152-2.JB"
Interrupt within 5 seconds to abort boot process.
Boot process failed...
The system is unable to boot automatically. The BOOT
environment variable needs to be set to a bootable
image.
C2600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(25e)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Wed 30-May-12 03:34 by binugopa
ap:

Converting PDF to XSTRING for Adobe in WD ABAP Application

I have a requirement to develop a WD abap application in the portal, where 300 PDF's would exist on our LAN all with the pernr number embedded in the name. When a user logs onto the portal, it would retrieve the correct PDF for their pernr and display in an adobe form. In the application, I know how I can use the username, to derive the pernr to get the PDF name.
Right now I can use the upload functionality to upload(with an upload UI element) a particular file and put in a PDF with adobe, However, If I want to point to a particular file (based on the pernr name) on a secure folder on our LAN, can I do that?
If I plug in a file name instead of using the upload UI element, I need to figure out how to convert the PDF to an XSTRING so that I can pass that xstring to the adobe form interface.
Also, is there even a way to assign a file name on a LAN to an upload element in a WD ABAP application or is it necessary to use the dropdown to retrieve the file name from the users desktop in order for it to convert ot a PDF correctly?
Thanks,
Pam Laverty

hi pam,
I think it's not possible to select the file automatically. use action must be there.
So use upload ui element, once you click on upload button and select the file, that file data will be in DATASOURCE ATTRIBUTE ( the attribute which is binded to data property of upload ui element ) OF UPLOAD UI element in XSTRING format.
From there you can pass it to pdf.
Regards
srinivas

How do you create/add additional LAN IP blocks to the Westell A90-9100?

I have a Linksys at home and the double NAT is killing me. I'd prefer to add another IP block to the ethernet interface of the Westell, but it is not as cut and dry as the Linksys router I have. Is there a way to do this, or am I stuck with the typical port-forwarding configs? The devices I seem to have minor issues with are the media hub and the UMI telepresence. They are functional, but some of the features are not working. If there was only one device setup for NAT while routing IP addresses to the linksys that would work for me.
Westell = 192.168.1.1
Linksys E4200 = WAN: 192.168.1.254 and LAN 192.168.11.1 (NAT Enabled)
I'd like to add a static route from the Westell to the Linksys and remove the NAT on the Linksys, but when I did so, all traffic was blocked at the Westell. I tried RIP, but that did nothing for me.
I'd prefer not to convert the E4200 into a switch due to the extra features on it like the USB port for an external drive.
Any suggestions?
Thanks

I agree with the last suggestion. There's no need to have port forwarding rules in both the westell and linksys . So kill your port forwarding rules you made for.the linksys in the westell , assign the linksys a static ip and then dump it in the dmz. Then let the linksys handle all the port forwarding and additional ip blocks or VLANS

When converting a PDF from a scanned image on a Canon MFP, some of the text is jumbled

I am trying to use the Exportpdf.acrobat.com service and when I convert an image that was made into a pdf from Word, it is fine. If I exposrt a pdf that was scanned in from a Canon IR 2030i MFP, some of the text comes out jumbled and un-readable. Is there a certain setting to fix this?

Doc: I've had a similar experience, and here are the details, investigation, and a workaround. My printer is a Brother MFC-645CN, and I'm using Snow Leopard (10.6.8) on a 2010 iMac quad i5 connected to the printer over my ethernet LAN. Are you using a Brother printer?
Firefox has shown this kind of nasty issue for the past six months or so. It seems to be related to the imaging algorithms in Preview when dealing with Firefox (now at v.12) and the Brother printer -- the screwy second page (and beyond) show up skewed and up-sized when doing a print preview also. No such problem seen in Safari or anything else. I am not currently using any other Mozilla apps on this Mac besides Firefox.
A few months ago I tested printing from my administrator account and a different user account. Firefox printing was completely normal and as expected. When I went back to my main user account, back came the funky second page.I went through extensive troubleshooting to try to chase it down, systematically removing and replacing apps and preferences and many other Library files related to printing, Brother drivers, Firefox, and Preview. Nothing helped. Solution was to migrate my user files to an account where the printing problem wasn't happening. I deleted the problem user account.
Everything was fine for about three weeks, and then with no warning, printing was back to the bad second page, just as before. I am stumped, and I'll let smarter people try to figure it out. I use Firefox a lot, and it's possible that some add-on setting is interfering, or a web page I visited turned the printing funky again. I just don't know.
Also checked on a Mac G4 running Leopard (10.5.8) and Firefox 3.6.28. No printing/preview problems there.
Now, for the work-around I am currently using -- print each page separately, one at a time. Page 1, then page 2, etc. Preview and printing looks completely normal. Hope this works for you until the bug is located and squashed for good.
Glenn

Thunderbolt Port Converter

I have a Thunderbolt RAID H.D. which working fine with my iMac but my old Macbook Pro (2010) is actually a display port (not work with Thunderbolt) so my Macbook Pro can't connect to it.
So, I am thinking to purchase a Converter for my Macbook Pro but I don't have Firewire cable (I don't want to purchase converter and cable both), so it is possible to plug the Thunderbold<->Ethernet and connect to my Macbook Pro by LAN cable?
Thank you very much

There is no way you are going to be able to use the ThunderBolt RAID HD with a Mac that does not have a ThunderBolt port.
The simple rule of ThunderBolt is that the ThunderBolt end of the adapter must be connected to a ThunderBolt port to function correctly. Then the other end of the adapter can be connected to what ever bus the adapter converts the ThunderBolt to. This rule holds even for the ThunderBolt cable which is the adapter you need. You connect one end to the ThunderBolt port on your Mac and the other end to the ThunderBolt RAID HD.
So in your case it will not work.

Problème DAQmx buffer + convertion

Bonjour,
Alors voila mon problème:
Je fais l'acquisition d'accéléromètres par le module 9234 avec un compactDAQ 9174. Je veux faire une acquisition avec des échantillons en continue. J'ai un traitement du signal pour obtenir un spectre en dB ou je fais une moyenne de 12 spectres à afficher.
Lorsque je suis en continue, je ne peux faire le contrôle qu'une fois car après il me marque problème de buffer, alors je voudrais savoir comment réinitialiser le buffer avant chaque contrôle??? ou alors avoir une aide pour ce sujet!!!
De plus, je souhaite générer le code labview au lieu du vi express pour pouvoir intéragir avec la sensibilité et les paramètres d'acquisition mais là aussi j'ai un problème, comme vous pouvez le voir sur mon image jointe, l'assistantDAQ est converti correctement seulement quand je lance le contrôle il ne se passe rien, je pense qu'il ya un problème avec la boucle!!!
Donc voilà en gros, je laisse une image et les vi a disposition, et le but principale est que mon contrôle des 12 spectres moyenné soient plus rapide en passant par l'acquisition continue et en vidant le buffer, qu'en passant par l'acquisition de N echantillons où la ça marche très bien mais le temps est beaucoup trop long!!
Merci et n'hésitez pas à me contacter pour plus d'inof
Arnaud
Pièces jointes :
Convertion DAQmx.jpg ‏233 KB
Acquisition signal Ambiance.zip ‏233 KB

Je viens de corriger un problème, en faite quand je générais le code, et que je lançais le contrôle, je ne sortais jamais de la boucle, du coup j'ai mis une constante a vrai et ça marche!!
Cependant, j'ai toujours le même problème à savoir la rapidité, quand je suis avec le vi express, mon traitement des 12 spectres se fait en 400ms et dès que je génére le code, la ça explose et ça met 2s à faire le meme travail!!!
Alors faudrait que quelqu'un m'explique pourquoi, parce que je suis perdu là!!!
Merci

Can jmf broadcast mp3 files?convert mp3 to wav format to enable streaming?

Hello... can jmf broadcast mp3 file format audio files.. so that it can accessible.. since it is playable... or does it require conversion to another for in audio in order for it to be streamed on LAN... Thanks and more power to JAVA..

Man, have you ever opened Logic before? If you had you would have noticed that these instructions are for Logic and yes you will obtain 44.1/16 files if you choose these options in the "copy/convert" menue.

How can I import my music CD from an external drive (other PC) via LAN?

How can I import my music CD from an external drive (other PC) via LAN?
I have tried by "add..." but without success.

Hello DIRP,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iTunes: About the Add to Library, Import, and Convert functions
http://support.apple.com/kb/ht1347
Best of luck,
Mario

QLLC to LAN convertion

Similar Messages

Maybe you are looking for