Qlogic 2300 HBA and secure path

Hi All,
I need to ask a question regarding secure path.We have E6900 sun hardware and Qlogic 2300 HBA adaptor. We connected this machine to HP EVA 5000 Storage and when we scan disks its showing two instead of one. I searched out some fourms and came to know that we have to install securepath for that purpose. Can any one please tell me what version we will install and 2ndly for time being can we install only one HBA or we need two HBA's?
Thanks in advance,.

i am facing the same problem with IBM SAN and IBM storage DS4300 connected to SUn v880r with 2 Qlogic HBAs---
Hope sun i has to upgrade thwie firmware to match all the SANs;;; isuppose its with the OEM frimware from sun that is being shipped where the problem get solved when i used a generic qlogic QLA2342 card on the same server and same combination.

Similar Messages

/dev/fc Qlogic 2300 card problem

I have just installed a Qlogic PCI 2300 card in two sun machines, one is a V480 and one is a V440. The V480 is fine and the card can be seen from the /dev/fc directory, the other box is where the problem is, there is no /dev/fc that has been created for the card plus on the install i get the following error
Installing QLogic QLA2300 driver as <QLA2300>
## Installing part 1 of 1.
/kernel/drv/q3ip_v9
/kernel/drv/qla2300_v9
[ verifying class <none> ]
## Executing postinstall script.
("pci1077,9") already in use as a driver or alias.
Installation of <QLA2300> was successful.
The thing is if i type modinfo|grep FC i get the following
27 123df4e 548a0 239 1 qla2300 (QLogic FC Driver v4.13.01)
61 13f08d4 6888 - 1 fctl (Sun FC Transport Library v1.14)
201 781c0000 c628 150 1 fcp (Sun FCP Pseudo Driver v1.25)
and when i run prtconf -v i get the following
fibre-channel, instance #1
System software properties:
name='hba0-max-frame-length' type=int items=1
value=00000800
name='hba0-execution-throttle' type=int items=1
value=00000010
name='hba0-login-retry-count' type=int items=1
value=00000008
name='hba0-enable-adapter-hard-loop-ID' type=int items=1
value=00000000
name='hba0-adapter-hard-loop-ID' type=int items=1
value=00000000
name='hba0-enable-LIP-reset' type=int items=1
value=00000000
name='hba0-enable-LIP-full-login' type=int items=1
value=00000001
name='hba0-enable-target-reset' type=int items=1
value=00000000
name='hba0-reset-delay' type=int items=1
value=00000005
name='hba0-port-down-retry-count' type=int items=1
value=00000008
name='hba0-maximum-luns-per-target' type=int items=1
value=00000008
name='hba0-connection-options' type=int items=1
value=00000002
name='hba0-fc-tape' type=int items=1
value=00000001
name='hba0-fc-data-rate' type=int items=1
value=00000002
name='hba0-pci-latency-timer' type=int items=1
value=00000040
name='hba0-pci-x-max-memory-read-byte-count' type=int items=1
value=00000000
name='hba0-link-down-error' type=int items=1
value=00000001
name='hba0-link-down-timeout' type=int items=1
value=0000003c
name='hba0-persistent-binding-configuration' type=int items=1
value=00000000
name='hba0-fast-error-reporting' type=int items=1
value=00000000
name='hba0-extended-logging' type=int items=1
value=00000000
name='hba0-queue-full-retry-count' type=int items=1
value=00000010
name='hba0-queue-full-retry-delay' type=int items=1
value=00000002
name='hba0-security-protocols' type=int items=1
value=00000000
Driver properties:
name='pm-components' type=string items=3 dev=none
value='NAME=qla2300(1)' + '0=Device D3 State' + '3=Device D0 State'
name='scsi-selection-timeout' type=int items=1 dev=(239,0)
value=000000fa
name='scsi-options' type=int items=1 dev=(239,0)
value=00107ff8
name='scsi-watchdog-tick' type=int items=1 dev=(239,0)
value=0000000a
name='scsi-tag-age-limit' type=int items=1 dev=(239,0)
value=00000002
name='scsi-reset-delay' type=int items=1 dev=(239,0)
value=00000bb8
sd, instance #46 (driver not attached)
System properties:
name='lun' type=int items=1
value=00000000
name='target' type=int items=1
value=00000000
name='class_prop' type=string items=1
value='atapi'
name='class' type=string items=1
value='scsi'
sd, instance #47
System properties:
name='lun' type=int items=1
value=00000000
name='target' type=int items=1
value=00000001
name='class_prop' type=string items=1
value='atapi'
name='class' type=string items=1
value='scsi'
Driver properties:
name='pm-hardware-state' type=string items=1 dev=none
value='needs-suspend-resume'
name='ddi-failfast-supported' type=boolean dev=none
name='ddi-kernel-ioctl' type=boolean dev=none
Hardware properties:
name='devid' type=string items=1
value='id1,sd@w4849544143484920373330313033353630303030'
name='inquiry-revision-id' type=string items=1
value='0000'
name='inquiry-product-id' type=string items=1
value='DF600F'
name='inquiry-vendor-id' type=string items=1
value='HITACHI'
name='inquiry-device-type' type=int items=1
value=00000000
sd, instance #48 (driver not attached)
System properties:
name='lun' type=int items=1
value=00000000
name='target' type=int items=1
value=00000002
name='class_prop' type=string items=1
value='atapi'
name='class' type=string items=1
value='scsi'
sd, instance #49 (driver not attached)
System properties:
name='lun' type=int items=1
value=00000000
name='target' type=int items=1
value=00000003
name='class_prop' type=string items=1
value='atapi'
name='class' type=string items=1
value='scsi'
sd, instance #50 (driver not attached)
System properties:
name='lun' type=int items=1
value=00000000
name='target' type=int items=1
value=00000004
name='class' type=string items=1
value='scsi'
sd, instance #51 (driver not attached)
System properties:
name='lun' type=int items=1
value=00000000
name='target' type=int items=1
value=00000005
name='class' type=string items=1
value='scsi'
sd, instance #52 (driver not attached)
System properties:
name='lun' type=int items=1
value=00000000
name='target' type=int items=1
value=00000006
name='class' type=string items=1
value='scsi'
sd, instance #53 (driver not attached)
System properties:
name='lun' type=int items=1
value=00000000
name='target' type=int items=1
value=00000008
name='class' type=string items=1
value='scsi'
sd, instance #54 (driver not attached)
System properties:
name='lun' type=int items=1
value=00000000
name='target' type=int items=1
value=00000009
name='class' type=string items=1
value='scsi'
sd, instance #55 (driver not attached)
System properties:
name='lun' type=int items=1
value=00000000
name='target' type=int items=1
value=0000000a
name='class' type=string items=1
value='scsi'
sd, instance #56 (driver not attached)
I am at the stage of pulling my hair out :) any ideas why no /dev/fc is being created ?
Cheers,
Mike

Hi, have you got this problem solved somehow ??
I have a similar situation, same boxes, same results with v880 and some problems with v490.
In prtpicl -v you see info about the adapter:
vendor-id=0x1077
subsystem-id=0x9
This correspond to HP adapter firmware, that should work with HP software (Secure Path). Are you using this ??
This may be a problem, an HP adapter (based on QL2300 but with modifyed firmware) and Sun driver.
How did you solved the issue ??
thanks

How to Set up HTTPOnly and SECURE FLAG for session cookies

Hi All,
To fix some vulnerability issues (found in the ethical hacking , penetration testing) I need to set up the session cookies (CFID , CFTOKEN , JSESSIONID) with "HTTPOnly" (so not to access by other non HTTP APIs like Javascript). Also I need to set up a "secure flag" for those session cookies.
I have found the below solutions.
For setting up the HTTPOnly for the session cookies.
1] In application.cfc we can do this by using the below code. Or we can do this in CF admin side under Server Settings » Memory Variables
     this.sessioncookie.httponly = true;
For setting up the secure flag for the session cookies.
2] In application.cfc we can do this by using the below code. Or we can do this in CF admin side under Server Settings » Memory Variables
     this.sessioncookie.secure = "true"
Here my question is how we can do the same thing in Application.cfm?. (I am using ColdFusion version 10). I know we can do this using the below code , incase of HTTPOnly (for example).
<cfapplication setclientcookies="false" sessionmanagement="true" name="test">
<cfif NOT IsDefined("cookie.cfid") OR NOT IsDefined("cookie.cftoken") OR cookie.cftoken IS NOT session.CFToken>
<cfheader name="Set-Cookie" value="CFID=#session.CFID#;path=/;HTTPOnly">
<cfheader name="Set-Cookie" value="CFTOKEN=#session.CFTOKEN#;path=/;HTTPOnly">
</cfif>
But in the above code "setclientcookies" has been set to "false". In my application (it is an existing application) this has already been set to "true". If I change this to "false" as mentioned in the above code then ColdFusion will not automatically send CFID and CFTOKEN cookies to client browser and we need to manually code CFID and CFTOKEN on the URL for every page that uses Session. Right???. And this will be headache.Right???. Or any other way to do this.
Your timely help is well appreciated.
Thanks in advance.

BKBK wrote:
Abdul L Koyappayil wrote:
BKBK wrote:
You can switch httponly / secure on and off, as we have done, for CFID and CFToken. However, Tomcat automatically switches JsessionID to 'secure' when it detects that the protocol is secure, that is, HTTPS.
I couldnt understand this. I mean how are you relating this with my question.
When Tomcat detects that the communication protocol is secure (that is, HTTPS), it automatically switches on the 'secure' flag for the J2EE session cookie, JsessionID. Tomcat is configured to do that. Coldfusion has no say in it. So, for JsessionID, 'secure' is automatically set to 'false' when HTTP is detected and automatically set to 'true' when HTTPS is detected.
     If this is the case then why I am getting below info for jsessionid (As you mentioned it should set with SECURE flag . Right???). Note that we are using web server - Apache vFabric .And the application that we are using is in https and there is no hit is going from https to http.
Name:
JSESSIONID
Content:
782BF97F50AEC00B1EBBF1C2DBBBB92F.xyz
Domain:
xyz.abc.pqr.com
Path:
Send for:
Any kind of connection
Accessible to script:
No (HttpOnly)
Created:
Wednesday, September 3, 2014 2:25:10 AM
Expires:
When the browsing session ends
BKBK wrote:
2]When I checked CF Admin->Server Settings->Memory Variables I found that J2EE SESSION has been set to YES. So does this mean that do we need to set HTTPOnly and SECURE flag for JSESSIONID only or for CF session cookies (CFID AND CFTOKEN ) as well ?.
Set HTTPOnly / Secure for the session cookies that you wish to use. Each cookie has its pros and cons. For example, the JsessionID cookie is more secure and more Java-interoperable than CFID/CFToken but, from the explanation above, it forbids the sharing of sessions between HTTP and HTTPS.
     I understood that setting thos flags (httponly/secure) is as per my wish. But my question was , is it necessary to set those flags forcf session cookies (cfid and cftoken) as we have enabled J2EE session in CF admin?. Or in other way as the session management is J2EE based do we need to set those flags for CF session cookies?.
BKBK wrote:
3]If I need to set HTTPOnly and SECURE flag for JSESSIONID , how can I do that.
It is sufficient to set the HTTPOnly only. As I explained above, Tomcat will automatically set 'secure' to 'true' when necessary, that is, when the protocol is HTTPS.
     I understood that it is sufficient to set httponly only.but how we will set it for jsessionid?. This is my question. Apache vFabric will alos set secure to true automatically. Any idea??

[ANN] Online seminar - Web services management and security seminar

Join us now (Thu 09:00am) for a live seminar about Web services management and security here:
http://www.oracle.com/technology/tech/java/newsletter/seminars.html

I have got the following error when i run the WebServicesAssembler.jar
D:\Oracle\Oc4j\j2ee\home>java -jar d:/oracle/oc4j/webservices/lib/WebServicesAss
embler.jar -config etc/config.xml
Exception in thread "main" java.util.zip.ZipException: The system cannot find th
e path specified
at java.util.zip.ZipFile.open(Native Method)
at java.util.zip.ZipFile.<init>(ZipFile.java:105)
at java.util.jar.JarFile.<init>(JarFile.java:110)
at java.util.jar.JarFile.<init>(JarFile.java:52)
D:\Oracle\Oc4j\j2ee\home>java -jar WebServicesAssembler.jar -config etc/config.x
ml
Exception in thread "main" java.lang.InstantiationException: Unknown deployment
tag in JMS Web Service Example: <option>
at com.evermind.xml.XMLConfig.parseDeploymentMainNode(XMLConfig.java:293
at oracle.j2ee.ws.tools.WsAssemblerConfig.parseDeploymentMainNode(WsAsse
mblerConfig.java:68)
at com.evermind.xml.XMLConfig.parseRootNode(XMLConfig.java:268)
at com.evermind.xml.XMLConfig.init(XMLConfig.java:147)
at com.evermind.xml.XMLConfig.init(XMLConfig.java:88)
at oracle.j2ee.ws.tools.WsAssemblerConfig.init(WsAssemblerConfig.java:30
at oracle.j2ee.ws.tools.WsAssembler.main(WsAssembler.java:17)

Logical filename and logical path in lsmw

Hi all,
I am doing a lsmw for purchasing info record . i created a logicalpath and assigned a physical path to that . i created a logical filename and assigned the logical path .but when i assign that to the lsmw it is throwing error as 'LOGICAL PATH DOES NOT POINT TO PHYSICAL DIRECTORY' .
can anybody provide a solution for that .
Thanks & regards
Magesh anandan

hi ,
goto the tcode file then u find the relation between the logical and physical paths ...and their assignment..
hope it will helps u..
regards,
venkat.

Blends: Difference between open and closed paths modifying spine

Okay, just had a discovery today about the blend tool.
The difference between closed paths and open paths is critical when you want to modify a blend spine, such as make it curve. Between open paths, there is no spine shown when a blend is created. Ever notice this? Between closed paths, there is a spine, which can be modified, such as making it curved. Now, the trick is how to modify a spine with open paths when there is no spine shown. Found out today that starting with a closed path, segments can be deleted to make the path open, then the spine can be modified and the open path state maintained!
This is a huge bug in Illustrator and makes no sense to me. Wanting Adobe to fix this in the next major release. Hope this helps anyone struggling with this issue.

One thing you should be aware of concerning open ended splines:
It makes an enormous difference as to how the blend behaves whether the endpoints have handles or not.
Give them handles and you will find that you can alter the distribution of the blend objects just by adjusting the handles or by dragging on the spline itself.
Give it a try.

What is the diff b/w Conventional Path and Direct Path?

What is the diff b/w Conventional Path and Direct Path?
While doing exp/imp
which one is best in peroformance Conventional Or Direct
consider my Oracle is 9i (9.2.0) and Os is Solaris 9
Could you please clarify.....
Thanks

http://download.oracle.com/docs/cd/B10501_01/server.920/a96652/ch01.htm#1005685

I have forgotten my apple security questions, when I go to My Apple ID and click on password and security, there is no option to reset my security questions even though I have a rescue email adress, how do i reset my security question ?

I have forgotten my security questions but when I click on My Apple ID and got to password and security, there is no option to rest my questions and/or send my self a rescue email, what do I do now ?

You need to contact Apple. Click here, phone them, and ask for the Account Security team, or fill out and submit this form.
(89174)

Start up problems after Safari 3.1 and Security update

Updated safari and security update last night.
Safari downloaded and installed but there was an error downloading or installing the security update, I forgot.
After I restarted everything booted up fine, but was stuck on "Starting Mac OS X" screen.
Did a fsck and zap the pram, still stuck.
Today I tried booting up in safe mode, stuck on the gray screen with the apple logo.
Then I tried booting up from an external firewire dvd drive. Repaired permissions, repaired the disk, but it is still stuck on "Starting Mac OS X" screen. Help please...
Thank you

Ok i had a similar problem, with all the recent updates for Leopard, including the 10.5.2 combo update... the 12" PowerBook G4 kept getting stuck on the grey apple and spinning wheel... if it managed to get past this it would get stuck on the blue screen!!!
The way i got around this, after trying all these other tips was: Archived & Installed 10.5; restarted, waited; downloaded 10.5.2 Combo update, installed; restarted, waited; waited; waited; after getting back to desktop, restarted, waited; then ran Software Update only installing one at a time, and after each install, restarted, waited; when all Software updates completed, proceeded with iLife updates etc... It took a while (still quicker than the 3 days of failed installs and updates) with a lot of waiting on the blue screen (5-20mins) but we got there in the end. Disks where checked with Leopard Disk Utility before and after, permissions where checked before and after completing all installs, also with a DW 4.1 optimization. Also note worthy is the RAM was upgraded from the initial 256Mb (!!!) with an extra Gb.

Failed attempt to move log and database paths

Hi. Can anyone offer any advice on what might have caused an attempt to move Exchange 2010 (SP3) mailbox database and log folder paths to fail? I can't diagnose it, and would appreciate any advice.
We have two databases in a two-node DAG, one mounted on each node. I removed the passive copy of each database before the move attempts. The first moved ok. The second failed. Here's a summary of what happened:
Task 1:
DAG-NODE-A ----------------------------DAG-NODE-B
MAILBOX-DB-01                               MAILBOX-DB-01
MOUNTED                                        HEALTHY (passive)
- Dismount database
- Remove passive copy.
- Move logfolder path from R: to L:
and move EDB path from S: to M:
- Succeeded.
- Mount datbase.
- Re-add passive copy
All ok.
Task 2:
DAG-NODE-A ----------------------------DAG-NODE-B
MAILBOX-DB-02                               MAILBOX-DB-02
HEALTHY (passive)                           MOUNTED
- Dismount database
- Remove passive copy.
- Move logfolder path from R: to L:
and move EDB path from S: to M:
- Failed. Paths not moved.
- Database now won't mount.
- Database eventually mounts
after approx. 30 auto retries.
- Abandon attempt to move paths.
- Re-add passive copy.
END
Here's some more detail, included event log and shell output:
So, as per the above, with Mailbox-DB-01 (active copy on DAG-NODE-A), Exchange moved the paths without a hitch and I was then able to mount the database and re-add the passive copy. I then tried to move the paths for Mailbox-DB-02 (active copy on DAG-NODE-B),
but after a few minutes Exchange aborted the move, outputting errors to the Shell, the application log and the MSExchange Management log. A second attempt failed because Exchange found that "The .edb file path is not available. There is already a file
named M:\Mailbox-DB-02\Mailbox-DB-02.edb" - Exchange had created an EDB file in the target location, but the source EDB file was still in the source location and the path was unchanged. Rather than re-trying the move again, I decided to try to mount the
database, to check it was ok, but it wouldn’t mount.
I left it alone for an hour or so to have a think about what to do, came back to it and found Exchange had mounted the database (without moving the paths) after around 30 automatic retries. I was then able to re-add the passive copy.
I’m not keen to re-try the move without knowing why it failed, why the database then wouldn’t mount, and why it subsequently recovered. Any advice would be appreciated. Many thanks.
Output included
- a WinRM error in the Shell’;
- an App Log error event from my attempt to mount the database after the move failure, saying an attempt to open the EDB file for read / write access failed with system error 32 because the file was being used by another process;
- events recording failure to configure and start the database, and noting a serious error which caused it to terminate its functional activity;
- Event ID 3154 from MSExchangeRepl, saying an Active Manager operation failed / database action failed / MapiExceptionCallFailed;
- Event ID 10056 from source MSExchangeIS Mailbox Store in the App Log just before Exchange successfully mounted the troublesome database, saying “Patch all ID counters for database Mailbox-DB-02.”
One other thing which may or may not be relevant – the MSExchange Service Host service stops soon after being started on DAG-NODE-B (reboots have made no difference). On DAG-NODE-A, it runs consistently.
Here’s what seems to me to be the most relevant output from the Application Log and the MSExchange Management Log on DAG-NODE-B, and from the Exchange Shell:
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 10:46:19 ESE 327 General "Information Store (3720) Mailbox-DB-02: The database engine detached a database (4, S:\Mailbox-DB-02\Database\Mailbox-DB-02.edb). (Time=6 seconds)
Internal Timing Sequence: [1] 0.000, [2] 0.000, [3] 0.000, [4] 0.000, [5] 0.000, [6] 6.188, [7] 0.156, [8] 0.016, [9] 0.015, [10] 0.016, [11] 0.031.
Revived Cache: 0"
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 10:46:19 ESE 103 General "Information Store (3720) Mailbox-DB-02: The database engine stopped the instance (4).
Dirty Shutdown: 0
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 10:46:19 MSExchangeIS Mailbox Store 9539 General The Microsoft Exchange Information Store database "Mailbox-DB-02" was stopped.
==================================================================================
DAG-NODE-B, MSExchange Management log
Information DD/MM/14 10:46:19 MSExchange CmdletLogs 1 General Cmdlet succeeded. Cmdlet Dismount-Database, parameters {Identity=Mailbox-DB-02}.
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 10:46:19 MSExchangeRepl 3161 Service Active Manager dismounted database Mailbox-DB-02 on server DAG-NODE-B.company.corp.
==================================================================================
DAG-NODE-B, MSExchange Management log
Error DD/MM/14 10:46:20 MSExchange CmdletLogs 6 General Cmdlet failed. Cmdlet Get-PublicFolderDatabase, parameters {Status=True, Identity=xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx}.
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 10:46:21 MSExchange Assistants 9002 Assistants Service MSExchangeMailboxAssistants. Stopped processing database Mailbox-DB-02 (xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx).
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 10:46:21 MSExchange Assistants 9002 Assistants Service MSExchangeMailSubmission. Stopped processing database Mailbox-DB-02 (xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx).
==================================================================================
DAG-NODE-B, Application Log:
Error DD/MM/2014 10:51:08 MSExchange Search Indexer 104 General Exchange Search Indexer failed to enable the Mailbox Database Mailbox-DB-02 (GUID = xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) after 10 tries. The last failure was: MapiExceptionMdbOffline: Unable to
get CI watermark (hr=0x80004005, ec=1142)
==================================================================================
DAG-NODE-B, MSExchange Management log
Warning DD/MM/14 11:06:44 MSExchange CmdletLogs 4 General Cmdlet stopped. Cmdlet Move-DatabasePath, parameters {Identity=Mailbox-DB-02, EdbFilePath=M:\Mailbox-DB-02\Mailbox-DB-02.edb, LogFolderPath=L:\Mailbox-DB-02\Logs}.
==================================================================================
DAG-NODE-B, Exchange Management Shell output
Processing data from remote server failed with the following error message: The WinRM client cannot complete the operation within the time specified. Check if the machine name is valid and is reachable over the network and firewall exception for Windows Remote
Management service is enabled. For more information, see the about_Remote_Troubleshooting Help topic.
+ CategoryInfo : OperationStopped: (System.Manageme...pressionSyncJob:PSInvokeExpressionSyncJob) [], PSRemotingTransportException
+ FullyQualifiedErrorId : JobFailure
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 11:23:42 MSExchangeIS Mailbox Store 1000 General Attempting to start the Information Store "Mailbox-DB-02".
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 11:23:43 ESE 102 General "Information Store (3720) Mailbox-DB-02: The database engine (14.03.0162.0000) is starting a new instance (4).
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 11:23:43 ESE 105 General "Information Store (3720) Mailbox-DB-02: The database engine started a new instance (4). (Time=0 seconds)
==================================================================================
DAG-NODE-B, Application Log:
Error DD/MM/2014 11:23:53 ESE 490 General "Information Store (3720) Mailbox-DB-02: An attempt to open the file ""S:\Mailbox-DB-02\Database\Mailbox-DB-02.edb"" for read / write access failed with system error 32 (0x00000020): ""The
process cannot access the file because it is being used by another process. "". The open file operation will fail with error -1032 (0xfffffbf8).
==================================================================================
DAG-NODE-B, Application Log:
Error DD/MM/2014 11:23:53 MSExchangeIS 9519 General "The following error occurred while starting database Mailbox-DB-02: 0xfffffbf8.
Failed to configure MDB. "
==================================================================================
DAG-NODE-B, Application Log:
Error DD/MM/2014 11:23:53 MSExchangeIS 9519 General "The following error occurred while starting database Mailbox-DB-02: 0xfffffbf8.
Start DB failed.. "
==================================================================================
DAG-NODE-B, Application Log:
Error DD/MM/2014 11:23:53 ExchangeStoreDB 215 Database recovery At 'DD/MM/2014 11:23:53' the Microsoft Exchange Information Store Database 'Mailbox-DB-02' copy on this server experienced a serious error which caused it to terminate its functional activity.
The error returned by the remount attempt was "There is only one copy of this mailbox database (Mailbox-DB-02). Automatic recovery is not available.". Consult the event log on the server for other storage and "ExchangeStoreDb" events for
more specific information about the failures.
==================================================================================
DAG-NODE-B, Application Log:
Error DD/MM/2014 11:23:53 ExchangeStoreDB 231 Database recovery At 'DD/MM/2014 11:23:53', the copy of database 'Mailbox-DB-02' on this server encountered an error during the mount operation. For more information, consult the Event log on the server for "ExchangeStoreDb"
or "MSExchangeRepl" events. The mount operation will be tried again automatically.
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 11:23:54 ESE 103 General "Information Store (3720) Mailbox-DB-02: The database engine stopped the instance (4).
Dirty Shutdown: 0
==================================================================================
DAG-NODE-B, Application Log:
Error DD/MM/2014 11:23:54 ExchangeStoreDB 231 Database recovery At 'DD/MM/2014 11:23:54', the copy of database 'Mailbox-DB-02' on this server encountered an error during the mount operation. For more information, consult the Event log on the server for "ExchangeStoreDb"
or "MSExchangeRepl" events. The mount operation will be tried again automatically.
==================================================================================
DAG-NODE-B, Application Log:
Error DD/MM/2014 11:23:54 MSExchangeRepl 3154 Service Active Manager failed to mount database Mailbox-DB-02 on server DAG-NODE-B.company.corp. Error: An Active Manager operation failed. Error The database action failed. Error: Operation failed with message:
MapiExceptionCallFailed: Unable to mount database. (hr=0x80004005, ec=-1032)
==================================================================================
NOTE:repeat events similar to some of the above continue until Exchange eventually manages to mount the database:
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 12:15:56 MSExchangeIS Mailbox Store 1000 General Attempting to start the Information Store "Mailbox-DB-02".
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 12:15:56 ESE 102 General "Information Store (3720) Mailbox-DB-02: The database engine (14.03.0162.0000) is starting a new instance (4).
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 12:15:56 ESE 105 General "Information Store (3720) Mailbox-DB-02: The database engine started a new instance (4). (Time=0 seconds)
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 12:15:57 ESE 326 General "Information Store (3720) Mailbox-DB-02: The database engine attached a database (5, S:\Mailbox-DB-02\Database\Mailbox-DB-02.edb). (Time=0 seconds)
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 12:15:57 MSExchangeIS Mailbox Store 10056 General Patch all ID counters for database Mailbox-DB-02.
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 12:15:57 MSExchangeIS Mailbox Store 1133 General Allocating message database resources for database "Mailbox-DB-02".
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 12:15:58 MSExchangeIS Mailbox Store 9523 General "The Microsoft Exchange Database ""Mailbox-DB-02"" has been started.
Database File: S:\Mailbox-DB-02\Database\Mailbox-DB-02.edb
Transaction Logfiles: R:\Mailbox-DB-02\Logs\
Base Name (logfile prefix): E03
System Path: R:\Mailbox-DB-02\Logs\
(Start Duration=00:00:01.844) "
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 12:15:58 MSExchangeRepl 3156 Service Active Manager successfully mounted database Mailbox-DB-02 on server DAG-NODE-B.company.corp.
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 12:16:06 MSExchange Assistants 9001 Assistants Service MSExchangeMailSubmission. Started to process mailbox database Mailbox-DB-02 (xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx).
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 12:16:09 MSExchange Assistants 9001 Assistants Service MSExchangeMailboxAssistants. Started to process mailbox database Mailbox-DB-02 (xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx).
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 12:16:12 MSExchange Assistants 9017 Assistants Service MSExchangeMailboxAssistants. Managed Folder Mailbox Assistant for database Mailbox-DB-02 (xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) is entering a work cycle. There are 125 mailboxes on
this database.
==================================================================================
DAG-NODE-B, Application Log:
Information DD/MM/2014 12:16:30 MSExchange Search Indexer 108 General Exchange Search Indexer has enabled indexing for the Mailbox Database Mailbox-DB-02 (GUID = xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx).
==================================================================================


If you used the steps outlined in this TechNet article - http://technet.microsoft.com/en-us/library/dd979782.aspx - then you should have been OK. I will say that I read one
article that said to work one database at a time, then when you are sure it is operational to go back and do the next, etc.
(I also assume by your shorthand at the beginning of this document that you performed the tasks on the active node when you did this work. If so, that's the best way to do it, so if it failed, it wasn't because you used the wrong steps or did them
on the wrong system.)

Bursting with translation and security attributes?

Hi folks,
I've been lurking on the forum for a while and despite not always finding a solution, existing threads normally pointed me in the right direction - so thanks :)
I'm working on EBS 11.5.10 with the latest Bi-Publisher 5.6.3 (5472959) and bursting (5968876) patches installed.
I have successfully done the following individual AR Invoice Bi-Publisher tasks:
1. translated an invoice RTF template by attaching an xliff file to the data definition,
2. applied security attributes to the template to restrict updates on the resulting PDF,
3. burst a custom AR invoice print and emailed the resultant pdf's.
The PDF generated by the combined Invoice print correctly applies the translation and security attributes; however when I run the "XML Publisher Report Bursting Program" to the XML file the resultant burst PDF's do not apply the translation or security attributes. I assume this a limitation of bursting control files? If so, is this on the list of future enhancements to Bi-Publisher?
Here's an example of my control file document entry, I have included locale and pdf-security entries - these don't cause an error but equally don't generate the desired result (p.s. I know I'm emailing on a PRI filter - it's just a test):
<xapi:document output-type="pdf" delivery="att_email">
<xapi:template type="rtf"
location="/usr/tmp/xxxINVOICE3.rtf"
locale="fr-US"
pdf-security="true" pdf-encryption-level="1" pdf-permissions-password="xxxxxx"
filter=".//G_INVOICE_HEADER[PRINTING_OPTION='PRI']" >
</xapi:template>
</xapi:document>
Thanks
Dave

=================
==Properties Idea's
=================
You would have happened to try applying the security stuff in the application for your template? Try that and see if the pdf properties get set.
If that doesn't work your left with two options:
1. create a java concurrent program and set the properties manually.
2. Log a tar.
=================
==local idea's
=================
Are you sure you don't have to create template config for the locale? i suspect that's why it's not applying the xliff translation. Also, your NLS_LANG needs to be set to FRENCH for the approriate template to be applied. If your logged-in as english your french format template will not be applied, neither will the translation. As an example you can query vl table and you'll only get american (us) but if you alter your session you'll get the translation for that language when your query the table.
location="xdo://xxxAR.xxx_XML_PRINT.fr.US"
try it out and see if that works. Note: This will only work if your session NLS_LANG is set to FRENCH.

HT2534 My friend created me an itunes store account with his credit card , his credit card is about to expire and they are asking me to re-enter the credit card and security card number .... I don't have these numbers ... How can i create new itunes accou

My friend created me an itunes store account with his credit card , his credit card is about to expire and they are asking me to re-enter the credit card and security card number .... I don't have these numbers ... How can i create new itunes account without credit card?????

Why do you need to create a new account?
Just change the payment method.
http://support.apple.com/kb/ht1918

I forgot the answers for the security questions and when I try to change them (My Apple ID - Manage your account - Password and Security) I'm asked to answer the exact questions I'm Trying to change because I don't remember the answers. How can I do it?

I forgot the answers for the security questions and when I try to change them (My Apple ID -> Manage your account -> Password and Security) I'm asked to answer the exact questions I'm trying to change because I don't remember the answers. How can I do it?

Can't you try the email option instead?

[Request] Move Windows Control Panel applet from "System and Security" to "Programs"

The "Flash Player (32-bit)" Windows Control Panel applet should be moved from "System and Security" to "Programs" where the Java applet is.
Vote: https://bugbase.adobe.com/index.cfm?event=bug&id=2953107
Thanks

njb,
Why not just run the ThinkVantage System Update and let it install as usual. You can also "un-check" those drivers that you don't want to install.
*Non Lenovo employee*
I have a Y2P (i5) ... Feel free to ping me if you want me to test some applications with your Y2P if you have the same model. I don't mind keep doing recovery on it if needed .... =)

System and security control panel

Could someone with a W520 take a screenshot of the lenovo apps in their "system and security" section of control panel please. I am doing a ground up install from bare windows 7 to get rid of the preloaded SQL server 2005 and adding back the programe I want.
Just want to seee what came preloaded.
Thanks

njb,
Why not just run the ThinkVantage System Update and let it install as usual. You can also "un-check" those drivers that you don't want to install.
*Non Lenovo employee*
I have a Y2P (i5) ... Feel free to ping me if you want me to test some applications with your Y2P if you have the same model. I don't mind keep doing recovery on it if needed .... =)

Qlogic 2300 HBA and secure path

Similar Messages

Maybe you are looking for