QM In-Process Inspection for Batch Managed Material

Hi,
I have a issue related to UD of In-Process inspection for batch managed material. The production process is discrete manufacting for a cold rolling mill. A production order can have mutiple coils as per the production amount. To track the individual coil , batch management has ben activated. We have both in-process as well as inspection after production here.
For inspection after production we are fine as we are doing partial confirmation after every coil and have separate inspection lot having different batch number.
But for in-process I can have only one inspection lot for the production order (created on release of the production order). I can do the result recording but while trying to do UD u2013 it is asking for a batch number as the material is batch managed. W/o entering the batch number system is not allowing me to do the UD.
Is there any solution/work around of this problem.
-Regards
ashim

Hi Ashim,
you raised a very good question? i am helpless here to execute same scenario,
but i disussed with my QM guy here, he said, once the material is batch managed then it has to ahve batch in UD.
so i discussed ur case, which is very much valid for heavy ind like cement and all,
so what i suggest, u create a dummy batch in the UD for in process (no inventory posting)
and at confimation give ur usual batch (if system propose the dummy batch which u give in the UD for inprocess, try to change there--- i hope it should allow)
i would really like to here answer from u for this.
try to do as suggested, and let me know the results.
REgards,
Pravin mukkawar

Similar Messages

MB1C LSMW Recording fails with missing Prod Date for Batch Managed Material

An LSMW recording for transaction MB1C that was batch managed was successfully recorded. This included the entry of the Production Date before pressing enter to post the Good Receipts. However, when the transaction was executed, the error came back, "Enter the date of production". In looking at the screen in the lsmw batch results, it shows the date in the production date field.
I also tried to create the recording in the Transaction Recorder (trancode SHDB), and process the recording simulating the background mode and got the same results.
Any ideas why it seems to be ignoring the production date? Any help will be greatly appreciated.

An LSMW recording for transaction MB1C that was batch managed was successfully recorded. This included the entry of the Production Date before pressing enter to post the Good Receipts. However, when the transaction was executed, the error came back, "Enter the date of production". In looking at the screen in the lsmw batch results, it shows the date in the production date field.
I also tried to create the recording in the Transaction Recorder (trancode SHDB), and process the recording simulating the background mode and got the same results.
Any ideas why it seems to be ignoring the production date? Any help will be greatly appreciated.

Specification for batch managed procured material

Hi all
I have created bom for non batch manage material.
I have added batch managed procured material in bom, I have done classification of batch managed procured material in BOM .
I have created production order for header material of bom manually and done MRP after that. It has created PR for that material.
But in PR. iam not able to see specification from classification data (BOM ) for procured item.
Is there is any config iam missing?

Closing thread in MM forum and opening it in PP.

Does SAP Provide any standard conversion program for Batch Managment activa

Hi,
An idea if SAP Provides any standard program to conversion of non batch managed material to batch managed material in a productive SAP Environment and close open documents,
It would be great help if somebody can reply to these queries.
Thanks in advance
Regards
Bijaya Pradhan

Hi
Use the same Driver program RIPROV00 which is used as Script driver program to fire the output from smartforms also
Only thing is little bit you have to modify the program such that it triggers the smartform instead of Script.
I think there is no smartform driver program for this IW21.
see some standard SF driver program like RLE_DELNOTE and
modify it and use it.
Reward points for useful Answers
Regards
Anji

In Process Inspection for Repetitive Manufacturing

Hi All,
I'm trying to perform in-process inspection for repetitive manufacturing. I have a semi finished material which has the inspection type 13 activated in the material master. Rate routing for it has also been created. Characteristics have been assigned to its operation and the routing is attached to a production version. When I o to MFPR to create a lot, I specify the material, plant and production version with QM active (tried the other 2 options as well) but when I execute, nothing shows up in the list. When I click on create inspection lot, it says, "either select versions or place cursor on versions now" but there's nothing in the list?
Regards,
Bilal

Hi,
Please check whether the repetitive manufacturing check box and REM profile is defined in the MRP4 of material master.
Please define that and try to run the transaction MFPR.
It should solve your problem
Regards,
Sumit Gupta

In Migo,the batch managed material automatically goes into restricted sk.

Hi
In Migo,the batch managed material automatically goes into the restricted stock.The batches are created at the time of receiving and i want it to be receive it in unrestricted stock.
Note:The batches are received at the time of receiving.
Regards:Vijay

do your customizing in IMG > Logistics General > batch management > Specify Batch Level and Activate Status Management
there is a button for initial status for new batch.
make sure that there is no flag in the status column of the entries shown.

Convert non batch managed material to batch managed

What are the prerequisites to convert a non batch managed material to a batch managed one?

Hi
check following link it will help you
[Prerequisites for activating batch management with inventory already in SAP;
[http://help.sap.com/saphelp_erp60_sp/helpdata/en/1b/877e40417c6d1de10000000a1550b0/content.htm]
[http://help.sap.com/saphelp_erp60_sp/helpdata/en/3c/faadb99f6f3c4da80421490e4c91d3/content.htm]
Regards
Kailas Ugale

In process inspection for partial confirmation of production order

Hi QM Guru,
how i will do in process inspection for partial confirmation of production oder
Senior is this I have maintain inspection type 03 in finish material u2026..suppose production order quantity 20 kg..there are 2 operationu202610 and 20.. I have maintained MIC on operation 20u2026after release the production order lot are generatingu2026but when they confirm operation 10 they do partial confirmation for 10 kgu2026.then again when do confirmation 20..they checku2026for quality resultu2026
Then I do the result record ok of 10 kgu2026then they confirm 20 operationu2026.
Now. again he do the confirmation of rest production order 10 kg..opration 10 ok..but in operation 20..system does not check for qualityu2026..
Again I want to do the quality inspection of 10kg on 20 operationu2026
How I will do. kindly suggest me
Regards
Aqueel

Hello
I think that the process can be mapped in one of these ways:
- according to what you describe this is closer to a good receipt inspection and not to in-process inspection, as the trigger for the inspection is the GR and not the release of the order. So, why dont you give a chance to a 04 inspection type, with inspection lot creation for every GR ? Check the indictor in MM02, QM view for "04" inspection, and uncheck the "Stock in quality", so you dont get caught by the stock in quality and resembles in process "Non-stock relevant" inspection
- alternatively you can define the use of inspection points ? So you are adding new results as new confirmations are made. Disadvantage: you can only give one usage decision to the inspection Lot, irrespective of the number of samples you have analyzed.
Regards

ATP check for batch managed products

Hello All,
I have a requirement for ATP check for batch managed products and would be glad if someone can help me on that. One of the characteristics on my product is expiry date. Business wants to restricts confirming products which has an expiry date of less than 90 days for orders outside the country. How can we achieve that?

Hello
You can try with activating Shelf Life Expiration Date (SLED).
For config, check SPRO - Logistice General - Batch master - SLED
Then finally setup Customer Exit to calculate/check the SLED.
Exit EXIT_SAPLMHD1_001 for enhancement SAPLMHD1.
Further, you can refer following SDN thread for reference/understanding:
- SLED by customer/ material
Regards
JP

Specific Identification Cost for batch managed items (Follow-Up from P2P)

Specific Identification Cost method is used for serial and batch managed item. Using this method, the outbound cost of such items would be the original cost of specific goods, which can be determined according to the serial or batch number of that item.
Business One allows the user to receive batch managed items with a batch number that already exists in the DB. Its possible that the received quantity is added to on-hand quantity in the warehouse. In such case, the quantity on-hand of that batch and the received quantity may have different costs.
What should be the system behavior in such case:
1. Block receipts to the same batch with different costs.
2. Write the difference to a price difference account, as done in Standard Cost method.
3. Manage the batch cost with Moving Average method.
This thread is continuation from 'Specific Identification Cost for batch managed Items' <a href="http://p2p.sap.com/businessoneforum?type=join&login=1&uid=41FB661A76CED536C825C4E2B6FF4397&cid=91&go=z37225">discussion</a> in P2P SAP Business One Forum (Product Development Collaboration).
Previous discussion on P2P is summarized in the attached file.

Hi Peter,
This is a very important functionality that you are describing here. For example, in the Steel industry, it could be extremely useful to cost by batch or serial number.
If you receive a batch that already exists in the system and if the costing method for the product is moving average, then teh cost of the batch should be calculated based on the moving average as well.
If the costing method is standard, then the cost should go in a variance account.
If the costing method is FIFO, then it is a getting trickier...
Regards,
Vincent

Customer exit for Batch management

Hi experts,
I'm using customer exit for batch management for internal number assignment.
I need the Batch number as i mentioned below
DDMMYYB01
DD-Date
MM-Month
YY-Year
B-Block
01-Number
For this i need to give logic. How to give i'm not getting. This batch number creation will come at the time of GR.
Anybody help me?
Naren

Hi
Please use the user exit SAPLV01Z as I mentioned in your other thread, please go to SMOD to read its documentstion.
In SMOD, select the 'Documentation' and click 'Display', this will show the overview documentation.
Select the 'Componnet', then ciick the 'Display'. select each component and click 'Documentation Ctrl+F4) this will show the detailed documentation of them.
Best Regards.
Leon.

Recurring Inspection is required for non batch managed material

Hi Gurus,
My scenerio is I want recurring inspection of material but my material is not batch managed. is there any way around to cater this requirement?
Regards

Without Batch management the reccuring inspection is not possible because if you receive 100 quantity of material A on date X and consume 50 and again you purchase 50 on daye Y and comsume 30 out of it .. Then how the system will know about when to trigger this inspection and for how much quantity..Even you use development the system canot identify the materials got consumed .. If it is serialized material then you can do it by creating the development table and maintaining the receipt date for each serial no and the inspection date...

No Inspection lot for HU managed Material

Please Guide Me.
Scenario :- 1
For HU Managed Raw Material , If we activate inspection type 01 , and in the parameters if I activate check Box of HU Management.
The follwoing process happens.
1. At MIGO - Inbound Delivery is created
2. And as we do GR against that Delivery - Inspection Lot gets generated.
But Here we have to do result recording / UD against HU.
Which Seems to be OK process.
Scenario :- 2
If we do not activate HU Management in inspection type 01.
Then My understanding is that we have to do RR / UD against the Material.
But In my case here - No Inspection lot is getting generated.At GR it shows that Material of the stock type Q.
For which we use VLMOVE. We see nothing in QA32.We do not do any RR/ UD.
Kindly guide me ... if I have to do any necessary config for the same.

If the goods are in a handling unit, you have to select the indicator for HU inspection. Else inspection lot is not created.

Material getting set for Batch Management in O/B delivery

Hi Folks,
For a material which is not batch managed, I created an outbound delivery.
For some reason, the material is getting set as 'BatchManagement' even though the Batch Management indicator is not set.
Due to this PGI is not possible.
Any thoughts on why the 'Batch Management' indicator has been set and how to resolve this?
Regards,

Hi Jürgen ,
I am unable to replicate this problem in Q. Its occuring only in P while doing a goods issue.
Message is
"The batches are not defined for delivery item XXXXXX".
As I said earlier, we have not set the batch management check box in MM.
However the outbound delivery has the batch management check box selected .
Anything I missed to check? Q is almost identical to P. But still issue is only in P.
Regards,

Inventory Count for Batch Managed materials - Plant, S.Loc and Batch Wise

Hi.,
In the company's current scenario, the printing of batch managed materials are scheduled under 3 Job names.
1. First job determines the materials/batches that need to be created today using Program RM07ICN1
2. Second Job Processes the BDC Session created by Program RM07ICN1 using Program: RSBDCSUB
3. Third Job prints the Inventory tickts at the appropriate Storage location using Program: RM07IDRU
Each Job has its own variant.
The Variant for SL.No 1 is defined w.r.t
i. Material Type : Two Material types have been defined
ii. Under selection variable, GIDAT ( Planned count date and GBDAT are flagged.
Current Analysis:
A. The inventory documents get printed with Materials as per the cycle counting indicators defined which govern which material has to be currently counted.
B. Inventory documents are generated for all materials in all the plants and in all the storage locations
C. Batches for a material number may print on different cycle count documents throughout the year.
Customer requirement:
The inventory documents to print on basis of
1. Material, Plant and S.Loc.
This would help in identifying the batches which are currently being counted as well.
2. Customers requirement is to ensure that all batches are accounted for and will identify any overage of batches since in the current process, they are never reviewed as a whole.
QUESTION:
1. How to configure the Customer requriement.
2. How to configure the Variant/s, if thats the place the configuration has to be done to satisfy the customer.
3. How to activate the Variant in SE37 after definition in the Step Indicator. Does it activate on execution?
When i run the Program using SE38 , maintaining options in the Screen ( giving Material, Plant and S.loc), i get the desired list (Batches w.r.t Material,plant.S.Loc). But there is a list of over 150 Batch managed materials and it would not be physically possible to maintain the variant for each each Material,plant,S.loc wise.
Is there a way to configure the customer requirement/s.
Any and all help is much appreciated.
Thanks

Hello Mahesh,
Customer requrirement is specific, they want a list of Inventory Documents to be generated on basis of Material in each Plant-S.Loc batch wise.
Then you need to define multiple varinat for the program.
(a) If i am giving two variants in the same Program name RM07ICN1, how to execute one after after in sequence.
In testing, I have defined in the " Step", Progran RM07ICN1 with one variant and Program RM07ICN1 with another Variant. But on execution of Program RM07ICN1 thru SE38, the screen defined latter ( second variant screen data ) is displayed.
You need to define several steps in SM36 transaction for the program using each variant. SE38 you can use only to save your variant data so later you can use this variant in SM36.
Once you schedule the job with SM36 and release it then it will automatically execute this job as per your criteria (timeline)
Hope this helps.
Regards
Arif Mansuri

QM In-Process Inspection for Batch Managed Material

Similar Messages

Maybe you are looking for