QM inspection type 89.

Hi gurus,
I created Insp.lot manually, means inspection type 89.
Whe I do the UD, Inspectio Stock Tab is not available.
What is the reason of that?
Thanks
JAB.

Hi juan
There are Two types of lots which are available as per inspection type.
1.stock posting can be done.(Ex 01,04,08)--->called stock relevent
2.stock posting can not be done(Ex 03,89 etc)-->non-stock relevent
When you create a manual lot(in QA01) in SAP it is alway  non stock relevent.
also this can be seen throuugh "Post to inspection stock" indicator is not available in 89 type of inspection.so stock posting can not be done.
I hope you understood...
Regards
Sujit S Gujar

Similar Messages

  • Follow up action 14 Inspection Type- Equipment status change

    could anyone tell me which follow up action for 14 inspection type is to be bought into for changing Equipment Availablity status to Non Availability status when I reject calibration lot for that particular equipment.

    hi
    kindly check whether this FM will work for you QFOA_OBJECT_STATUS_SET
    regards
    thyagarajan

  • How to maintain inspection type at the time of material creation using LSMW

    Hi All,
    I have a differnet Issue.
    I am using a std. LSMW to create the materials.
    But now using same LSMW i have to maintain Inspection types(ART-RMQAM) for the materials to be created.
    How this can be done.
    This filed is not found in any structures like BGR....to  BMMH8
    Can I create such a structure ??
    Amol

    Some need the hard answer: it is not possible in one go.
    It is an embedded functionality in material master like classification, but it is not stored in a material master table.

  • Link of material movement with inspection type

    Hello Masters,
    I have scenario where component at shop floor will be segregated for inspection. The requirement is to do result/defect recording for those parts and if required then those parts need to be scrapped. So one way of doing that can be to move those parts to either blocked stock or QI stock (ideal option) or to specific storage location so that planning can be taken care of (if material are still in unrestricted then planning will consider those part as OK part and planning may fail). And to record result/defect we require inspection lot, which can be created by using above mentioned material movement.
    But problem is how to create inspection lot so that we can do result/defect recording for those materials and scrap those material.
    Please note that material master will have QM setup active (inspection type 01 - Goods Receipt Insp. for Purchase Order) and hence we can move material from unrestricted stock to QI stock only through QM.
    I am not sure if we should use inspection type 08 - Stock transfer inspection, as there can be many instances of material transfer within plant. And with inspection type 08 active, system will create inspection lot every time there is any material transfer.
    One way can be to create new goods movement only for this kind of transfer and new inspection type and link both together. So that when ever material is transferred using that particular goods movement, system creates inspection lot as well as material will be in QI stock. But I am not sure how this is possible or not and if yes then how this can be done.
    I know query was too long to read and I think I was clear enough to explain what the requirement is.
    It would be great if I can get some guidance from you masters at the earliest convenience as it is bit of importance.
    Thanks and regards,
    Devang

    Hi Devang,
    I guess this is Line rejection scenario. Correct me if understanding goes wrong. You have okayed the material against 01 inspection lot and UD has been given. Now you find this material defective on shop floor.
    I think the 2nd option suggested by marwadi sounds better. I suggest one more possibility, just check whether feasible.
    1.     Create quality notification Q2 type through QM01. While creating you can give references of original PO and material document, which fetch vendor name and material code automatically.
    2.     Record defects and all other required information in notification.
    3.     After this, you find an option in action box, transfer post unrestricted - >block . Click there. This will transfer the stock from unrestricted to block.
    4.     If you want planning persons should not consider this stock as OK, remove block stock from MRP stock availability check. As a result of which stock lying in block will not be considered as available stock.
    5.     From block stock you can send this material back to vendor through MIGO. Otherwise you can create return delivery from notification through action box also. Check what is feasible in your case.
    Here you need not create inspection lot, no need to use any user exit.
    Regards,
    Anand Rao

  • Inspection lot creation for inspection type 05

    Hi Gurus,
    We have finished material FERT & semifinished material HALB.We have assigned insp. type 02 & 05 in material master of matl. HALB.When we create production order for FERT & confirm the order , inspection lot is generated for matl.HALB of inspection type 02.
    Now we are reversing the goods issue by movement type mb1a, movement 262.In customizing for movement 262 inspection lot origin 05 is assigned.
    My problem is that when i reverse the goods issue with mvmt.262, inspection lot is not created for insp. type 05. What should be the reason behind this? or are any changes to be done to above setting?
    Regards
    Ram

    Hi Ram,
    Just check the SPRO setting SPRO---> Quality Management ->Quality Inspection->inspection lot creation--->inspection for goods movement --->deactivate quality inspection for a movt type.
    Here against movt type 262 uncheck the QM not active tick.
    It will solve your problem.
    Cheers,
    Tushar

  • Inspection type 01 - inspection lot creation based on vendor batch number

    Hi Guys,
    this topic has been discussed several times here, but I was not able to find a suitable answer for my question.
    I am facing the folowing requirement:
    I have activated inspection type 01 for a raw material.
    I am receiving a firs goods receipt from vendor A with vendor batch number 0001.
    The system creates its own goods receipt batch number 0546 based on internal numbering.
    A new inspection lot is created.
    I am posting a second goods receipt from vendor a with vendor batch 0001.
    The system creates a new batch number 0547 based on internal numbering.
    A new inspection lot is created.
    I do not want to get the second inspection lot, because I received vendor batch 0001 before and I am assuming it has been inspected or is in inspection.
    Option 1: Post the second goods receipt against the first internal batch number created.
    I am aware of this need at the moment, but a user is not always checking if there is an internal batch with the same vendor received before.
    Can I customize the system to create inspection lots based on the fact that the vendor batch number was received before?
    Or do I have to use an exit and some ABAP code to get the wanted result?
    Thanks for your advice in advance.

    You need to use one of the enhancements that Do-Wook has suggested.  There is no standard SAP way to suppress the inspection based on the vendor batch number.
    With the first enhancement you use the system to check for a previously received vendor batch and if one is found, then that batch number is proposed and not the next one from the numbering series.  In this case, the lot isn't created than due to the inspection lot control of the inspection type.
    With the second enhancement you check the vendor batch number and if it's been received you suppress the inspection lot creation and the stock goes right to unrestricted.
    You'll probably need to do one or the other.  Myself, I prefer the first enhancement.
    Craig

  • Mass creation of Inspection types

    Dear QM gurus
    How to create the inspection types in mass processing?
    For example I have to assigne  inspection type 05 for 100(with activation of Inspection Type indicator) materials (the material masters are already created )
    is there any method?Without using BDC or LSMW can i do it by MASS or MM17?
    Thanks
    MK

    There is std T code available for activation of Inspection type in SAP-QM
    Use T code QA08
    Enter Material & plant and Inspection type with mass processing.
    Regards
    Sujit

  • Creation of inspection type (mm02 insp.setup) in mass

    Hi All,
    Is there a way of creating inspection type for all materials via mass update.
    It is in the Quality management view of mm02.
    Thanks
    Venkat

    Hi
    Try to use trx MASS
    Max

  • GR Purchase Order to Blocked Stock / Inspection Type 01

    Hi all,
    I want to receive 100 KG of Material X from a purchase order:  95 KG to Quality Inspection Area and 5 KG to Blocked (Stock Category S)
    For the 5 KG to be received to the Blocked Stock, I used movement type 103, the material was received to "GR Blcoked Stock".
    Then I used movement type 105 to release it. I chose Stock Type "Blocked".
    After posting, the material was received to "Quality Inspection Area" and NOT to Blocked Stock. I think the reason was the Inspection Type 01 was activated, so the material was received by default to Quality Inspection Area.
    How can I receive a material directly to "Blocked Stock"?
    Regards,
    Kifah Yacoub

    thank you, but it seems you misunderstood my question.
    What i want is: How to receive from purchase order to Blocked Stock (Stock Category S).
    I tried movement type 103, but it's not exactly what i want.
    Thank you

  • Digital signatures for calibration inspection (inspection type 14)

    Hi,
    I want to use digital signatures for results recording and usage decision (ud) when performing a calibration (inspection type 14). Normally you'd set-up the material authorization for digital signatures. But this can't be added to maintenance plans or equipment. Is there any way to set-up digital signatures for calibrations?
    Regards,
    Maarten

    Explore SAP Note 576307
    It may help u.

  • In-process inspection in repetitive mfg-  Inspection type - 13

    Hi there,
                 Can any one please tell me what is the differrence between the inspection type -03 & 13.
    As per my understanding the only diff is that 03 is used in discrete mfg & 13 in repetitive mfg...
    what is the other differrence ........??
    Regrads
    Kaushik

    Hello Kaushik,
    actually you have already found out that 03 is for descrete and 13 for repetive manufacturing. What is the difference?
    03 Descrete Manufacturing : Limited production numbers and can be assigned to a customer order. Example: A computer built with various extras (built to order).
    Accordingly inspection plans and inspection points assigned can be configured rather freely.
    13 Repetitive Manufacturing: Production lines produce the same product in an unlimited number over a longer period of time. Example: Screws M8 x 40 mm (Mass production). In this case inspection plans need a relation to either time, numbers etc.
    I hope that this information answers your question.
    Regards
    Isabelle

  • Cannot create copy of Std inspection type 08 (Stock transfer inspection)

    Dear All:
    I have created a copy of std inspection type 08 as Z08CP. I have made all the relevant assigments in IMG such as Maintain Inspection Lot Origins and Assign Inspection Types, Default values, etc.
    During my unit testing I did use the newly created Z08CP but I have noticed I keep getting the error message " Change the inspection stock of material XXXXX in QM only" BUT THE MOMENT I SWITCHED THE MATERIALS MASTER BACK TO inspection type 08 the problem is gone. Only when I have the std inspection type in the material master I am allow it to post a MB1b (322) and created the inpscetion lot in the background
    Weird !!
    Any ideas.
    Regards,
    Mauricio

    Let me see if i understand exactly what you guys are saying.
    Following entries have been made in IMG
    1. Plant dependent QM settings. Inspection Type for Available Stock in Quality Inspection field is empty
    2. Maintain Inspection types: Created Z08CP as copy of 08
    3. Maintain Inspection Lot Origins and Assign Inspection Types. For lot origin 08. created the following relationship
    Lot Origin 08
    01     08     Stock transfer inspection
    02     Z08CP     Prod Defect: Stock transfer inspection
    4. Default values for inspection type. Copied default values from 08 to Z08CP
    Note i did not make any changes to IMG section "Inspection for Goods Movements"
    I tried again and same error was displayed. what is that I am missing here?
    Regards,

  • Inspection lot with inspection type 03 - Using Inspection plan

    Dear friends,
    I want to create an inspection lot at the time of production order release (ideally - insp type 03). But I want to use inspection plan as a task list instead of routing for that lot.
    Is it possible?
    Best Regards,
    Avinash

    Hi Swapnali,
    Was expecting this re-question.
    We are at a stage where system is already ready. The routing master data contains large number of alternatives and huge number of parallel sequences. We were looking for a solution in which we would make an inspection plan without touching routing master data. Second I want to create the lot at the time of order release (basically one lot per production order) so don't want to use insp type 04.
    In config, I assigned task list type Q in front of lot origin 03 (Maintain Inspection Lot Origins and Assign Inspection Types).
    But still system is picking the routing and not inspection plan. Is there a way out?
    Regards,
    Avinash

  • Report on material with inspection type

    Hi,
    is there any report which can show which material is assigned to which inspection type.
    regards
    Raj

    Dear Raj
    1 ) Make use of QA08. 
    2) Give the plant and choose in the TAB Deactivate inspection Type
    3) Maintain the inspection type 01 or 04 .
    4) Execute
    5) It will give you a list of material for which inspection types are assigned.
    you can even assign inspection type in mass through this
    hope this helps
    Regards
    Gajesh

  • Problem in bdc for adding another inspection type in mm01

    Hi,
    i had made a code in which it will maintain the quality view and there it will going to insert twi insoection type ZSTAGE and 03 . Te problem is when it uploads the value of 1 inspection type it works fine but when it is going to insert another insoection type i.e. 03 it again picks up the zstage .
    plzz provide me guidlines how to solve this problem that both of the inspection type should be inserted.
    here's d link for the code:-
    http://docs.google.com/Doc?id=dfxswwff_1p9zdnnf2
    Edited by: ricx .s on Apr 20, 2009 8:48 AM

    ur  code  looking  ok..
    just change  it..
    call function <b>'WS_UPLOAD'</b>--->to  <b>gui_upload</b>
    EXPORTING
    FILENAME = p_fl_mct
    FILETYPE = 'ASC'
    TABLES
    data_tab = Tmp_tab
    EXCEPTIONS
    CONVERSION_ERROR = 1
    FILE_OPEN_ERROR = 2
    OTHERS = 10.
    if sy-subrc <> 0.
    message e398(00) with 'Unable to upload data'.
    endif.

  • Make Inspection type 02 stock relevant

    Hi Experts,
    I have attached inspection type 02 for material ,
    During material transfer from one plant to another by means of stock transfer,(STO-VB,T code ME21N-VL03N) goods issue takes place, An inspection lot is generated, which is not stock relevant, How can i generate inspection lot with stock in Quality Inspection.
    Waiting for your replies,
    Regards,
    Nitin

    Dear Nitin
    02 inspection type is not stock relevant.
    What is the movemenet type you are using for stock transfer. make sure that you have QM active for that movement type. you can activate this in the config
    Inspection for Goods Movements
    MG Path:  Implementation Guide for R/3 Customizing >Quality Management >Quality Inspection > Inspection Lot creation -> Inspection for Goods Movements
    regards
    gajesh

Maybe you are looking for