QM Manual Inspection Lot - with Inspection lot origin 89

Hi QM Guru,
I did maintain inspection type 10 in this material but while i would like to create the inspection lot manually.
I try to create manual inspection lot manually , i encounter this error with Inspection lot origin 89.
No valid inspection type for material 10000037 was found or selected
Message no. QA280
Diagnosis
An active inspection type for the material 1XXXXXXX in plant XXXX could not be found for the specified origin 89 or none of the available inspection types was selected.
System Response
Inspection lots cannot be created.
Procedure
Check the inspection type setting in the material master.
Is there anything which i missing ?
Thank you.

Hi,
I hope you have got the answer for this query. You get this error because you are trying to create a manual inspection lot (origin 89) of a material for which Inspection type 89 is not activated.
From your statement,
I did maintain inspection type 10 in this material but while i would like to create the inspection lot manually.
I try to create manual inspection lot manually , i encounter this error with Inspection lot origin 89.
It is clearly stated that you are using different inspection types. As Rama has suggested, activate Inspection type 89 in the material master and make corresponding master data.
Other than that, you cannot create manual inspection lot for the origins 10, 11, 12, 13 & 14. Similarly, Automatic inspection lots cannot be created for origins 07, 15 & 89. This answers your further query raised in the thread.
ntn

Similar Messages

How to differentiate the insp lots with same lot origin

Hi,
My client is
1. Procuring a Finished good directly ( same way as Raw material is being procured ) & then sale it.
2. In another scinarion the same material may be produced at Vendor's end ( Sub contracting )
3. In another scinario this is in house produced material.
Now the requirement is seperate tracking / list for each case.
Inspection type 04 can be activated to address the 3'rd case.
But how to segregate 1'st & 2'nd case from each other ???
I have created one new inspection type Z01 for lot origin 01. Similarly insp type 01 is also activated.
If Z01 insp type is marked as preferred insp type, then system always consider this insp type.
How to differentiate inspection type Z01 & 01 at incoming inspection stage ????
regards,

Dear Gajesh / Roderick
Thanks for reply & Sorry for the delayed reply from my side.
Gajesh as per your suggestion i used the break point in user exit QAAT0001 & after that i have executed PO & MIGO transaction, But after executiing it did not stop at a particular break point.
AM i doing some thing wrong???? or any alternate solution is there??
Roderick, i have explored the status profile but found to be use fulll for changing stage one time only. i.e. between 0101 to 01. But here i want to choose the inspection type base on PO type.
Kindly suggest further action.
Once abain thanks.
regards,
Singh
Edited by: Singh15667 on Jul 24, 2009 10:54 AM

Inspection lot with inspection type 03 - Using Inspection plan

Dear friends,
I want to create an inspection lot at the time of production order release (ideally - insp type 03). But I want to use inspection plan as a task list instead of routing for that lot.
Is it possible?
Best Regards,
Avinash

Hi Swapnali,
Was expecting this re-question.
We are at a stage where system is already ready. The routing master data contains large number of alternatives and huge number of parallel sequences. We were looking for a solution in which we would make an inspection plan without touching routing master data. Second I want to create the lot at the time of order release (basically one lot per production order) so don't want to use insp type 04.
In config, I assigned task list type Q in front of lot origin 03 (Maintain Inspection Lot Origins and Assign Inspection Types).
But still system is picking the routing and not inspection plan. Is there a way out?
Regards,
Avinash

Minimum Lot with Fixed Lot

Hi Experts
I have one requirements that our some of the vendors can be supplied the minimum lot of 1200 Kg but after that they can supply the fixed lot of 600 Kg due to packing constraints but as per my understanding in standard SAP we can not set these both parameters simultaneously.
Please suggest.
Regards
Ajay Goel

Hi,
Based on which criteria you can define that the vendor can supply 1200kg for first lot and after that 600kg? Is it per day delivery constraint or anything other? Could you please elaborate.
Regards,
AKPT

Inspection Lot with Zero stock posting qty

Dear QM Consultants,
We have come across following scenario,
1.     Repetitive manufacturing
2.     Material has inspection type 04 and Z04. Preferred inspection type is not ticked. Z04 inspection type has been assigned to inspection lot 04.
3.     Production GR done by 131 movement
4.     Inspection lot generated with reference to 131 movement type. Lot for inspection type 04 is created.
5.     Inspection lot qty in QA32 it shows correctly as that of GR qty.
6.     But when we click on UD, in stock posting tab, qty to be posted it shows as ZERO. So no qty is available for stock posting.
Has anybody came across such scenario? Is this any bug? Any SAP note for this?
Best Regards,
Anand Rao

Dear Sujit, Thanks for so prompt reply,
Basically this is a complex case,
1.     See we have set Posting Proposal in Usage Decision as u2018To unrestricted useu2019 in selected sets for usage decision. That means we need not every time go to stock posting tab. The moment we select ACC UD code it automatically posts the stock to unrestricted use.
2.     Now, what has happed, by 131 movement declaration, backflush happened with 261 movement for child parts.
3.     Inspection lots with inspection type 04 were created. (Here we did not note whether the stock was posted in quality inspection or in unrestricted use)
4.     Now the requirement is to cancel 131 movement document. Kindly note UD were not given up to this moment.
5.     Now through MFBF, user did document specific reversal. As a result of which and as per my knowledge 132 movement should happen and 262 should also happen. At the same time inspection lot status should be set to LTCA. But in actual case 132 movement happened and 262 did not. Surprisingly inspection lot did not set to LTCA status. It remained in REL mode only.
6.     After this document specific reversal, user gave UD to these inspection lots without noticing where the stock was lying.(in unrestricted or in quality inspection). So the lot status set to UD   ICCO SPCO STUP after giving usage decision.
7.     Now while doing reverse engineering that why 262 movement did not happen, we came to know that no 321 movement happened for the inspection lots which were generated with reference 131 movement document
8.     Also, qty to be posted it shows ZERO as explained in my earlier post.
9.     When we display 132 movement document through MIGO, in where tab it shows stock type as Quality inspection. That means stock was lifted from QI for 132 movement.
In short it cannot be predicted where the stock was actually posted whether in QI or in unrestricted use. But yes the post to inspection stock tick has been ticked in material master.
Can you help further in this regard?
Best Regards
Anand Rao

Manual Inspection Lot for Inspection Lot Origin '04'

Dear SAPians,
We are presently getting Automatic Inspection lot with the Closing of Process order against Inspection Lot Origin '04'. Now there is a requirement came to generate Manual inspection lot against Inspection Lot Origin '04' but System is STOPPING US and giving an Error Msg. You Cannot Enter A Material for the Specified Origin. I feel that there is some customizing issue. Please suggest.
Thanks

Yes Atul,
The system is correcting you, remember the 04 type lot triggers in reference to the Order!!!!
So don't enter the Material, just enter the Plant and inspection type i.e. 04 and press enter in QA01 trx.
The system will ask you for the Order number.
NOTE:- This will be manual lot (Other inspection), so will not have the stock posting tab at UD, though it will have number range of 04.............
Regards,
Shyamal

Inspection lot with 01 origin for stock transfer (Intra company STO)?

Hi Sap Gurus,
As per standard SAP configuration for 101 movement type, 08 is the inspection type used for stock transfers (Intra company STO). But, there is a requirement from business to use 01 for Intra STO. Is it possible to get an inspection lot with 01 origin while GR to the delivery created for Intra STO ( Stock transfer B/n plants from same company code)?.
Thanks in advance
Venkat V

Hi All,
Thanks for your replies..
Its STO Purchase order between two plants under same company code. System triggers movement type 101 with movement indicator B - Goods movement for Purchase order and Receipt indicator X - Stock transport order. Here system expects inspection lot origin 08 as per standard SAP configuration(OMJJ).
I just wanted to check, is it possible to get inspection lot from 01 origin for this type of stock transfers. If anyone who worked on this area, please share your inputs.
Thanks in advance
Venkat V

Manual inspection lot with out specification

Hi gurus,
can anybody give me an example for Manual inspection lot with out specification?
regards,
sbabu

Hi,
Actually it is not useful in manual inspection lot because manual inspection lot used to check your quality of material at any movement.
Means for example your raw material is in store department but some time you suspect something about quality & you take decision to check quality of material that time it can be used. So in this case result record is mandatary,
Because your intention to create lot to checked material so not use ful without specification .
Also not any posting happening through this lot.just to check the material at any instance.
For any further clarification revert me back.
Some time client want to create lot but do not want to take results for that just they are interested in giving
UD & stock posting in that case you can remove tick task list required .This requirement mostly demanded for certain Engg items they do not want go material directly to unrestricted. it will go through UD.
But manual inspection lot I do not think it much useful.
Regards
SANIL

Inspection lot with Production Order

Hi friends,
I am PP consultant and need some help in setting up a scanario of Production order with inspection lot.
I need to setup a scenario where a inpspection lot is created from production order manually (not at the time of release). The purpose is to post few quantity of production order to scrap storage location. Inspection lot needs to be created only in certain production orders where some of the quantity has to be declared as scrap and that needs to be rejected with usage decision.
can any one please suggest the overview of such scenario.
Regards,
Rohit

Dear Rohit,
You want to create a manual inspection lot only for the purpose of Scrapping and also want it to be done with Usage Decision.
You can not use inspection type 89, as it is not stock relevant (Inspection type for Miscellaneous inspection),
There is one another solution with inspection type 08( inspection for Material Movement), but it might look Lengthy.
1. Release a Production order. say 100 qty.
2. If during process, 10 is scrap, then perform Partial Confirmation of 10 Qty.; Stock will be in Unrestricted.
3. Now, through MB1B, transfer 10 qty from Unrestricted to QI.
4. As you have inspection type 08 active, System will create an Inspection lot for 10 Qty.
5. You can post this whole 10 qty to Scrap while giving Usage Decision.
I think, in your process, Scrapping is not done frequently, that is why you do not want inspection lot at every production order.
in that case this solution may solve your problem.
regards,
Amol
Edited by: Amolbook on Jan 12, 2012 3:13 PM

Creation of Recurring Inspection Lots with Serial numbers

Hello,
We have the following scenario at our client :
MIGO_GR is used to create GR for materials with Serial number requirement. The serial numbers can be generated automatically or manually entered on the screen. At this point of time, the Shelf Life expiry date & Next Inspection date are calculated based upon the Production date. The Batch gets created with Next Inspection date, Inspection Lots are created and the Serial numbers are assigned by the system. The stock moves into QI.
The stock is moved from Quality restricted to Unrestricted stock via QA11. The serial numbers are handled by the system or can be managed on screen.
Transaction QA07 (Deadline Monitoring of Batches) is used to create Recurring Inspection. QA07 gives error message IO304 that "Only 0 serial numbers entered instead of 1". The problem is that system doesn't pick up the corresponding serial numbers.
OSS # 497845 mentions that Transaction QA07 can not handle serial number. The serial numbers are very critical to the business process.
Has anyone come across this situation before ? Please suggest solution or workaround. I tried using BAdI "INSPECTIONLOT_UPDATE" & was able to create Inspection Lots with serial number assignment, also manipulated Batch to change the Next Inspection date. The problem is Material Movement (322) Document does NOT get created.
Also tried implementing BAdI as per OSS # 608830 but doesn't give desired results.
Any help is greatly appreciated.
Best Regards,
Homiar Kalwachwala.

Hello all,
Just wanted to bring this on top to be noticed.
Would appreciate any help, suggestions...
Regards,
Homiar.

Weighted from quality score of chars. with Inspection Lots

Dear QM Guru's.
My question is about Quality Score with Inspection Lots.
The Scenario:
1. In a Quality master View in Material Master I use the option number 05 of The Q-Score Procedure (Weighted from quality score of chars.)
2. I use Inspection Points.
3. I have 10 Inspection Points in a Characteristic.
4. When I make the Usage desicion, the Quality Score takes the last Inspeciton point.
The questions:
1. Why the Quality Score does take the last Inspection points, ?
2. Is there a chance The Quality Score taking the average of all inspection points ?
Thanks in advance.
Federico

This procedure calculates the quality score as the weighted average of the characteristic scores.
The score for the characteristic is determined on the basis of the defect class score for the characteristic result. You define the weight of the characteristic in the inspection plan.
                                      Sum ( E_KQD(characteristic) * WEIGHT )
           E_KQD =                 ___________________________
                                                 Sum ( WEIGHT )
With E_KQD (charac.):       Score for characteristic defect class.
                              If the defect class is blank or zero,
                             the result corresponds to the maximum
                             allowed score.
     WEIGHTING:      Weight of characteristic according to
                             inspection plan.
Now
As I understand It is Maximum allowed score which you have defined or the Avg one.
If you want to have the Avg of all inspection points then Copy & modify the function module   KQD_COPY_REFERENCE_FORM ( originally KQD_FEATURE_CLASS_WEIGHTED )

Inspection Lot quantity change (lot origin 03) when Prod. ord. qty changes?

Hi,
it seems that for an inspection lot, with lot origin 03:Production, its Inpsection Lot qty doesnt change when the Production order Total Quantity field changes. Only the Actual Inspection Lot changes.
How can the Inspection lot quantity field of the Inspection Lot be changed accordingly?
Should the enhancement PPCO0007 be used?and then LOSMENGE (table QALS) =GAMNG (table AFKO)
Can it be done?
Thanks in advance

Hi,
In that case, you can do it by :
- Reread the master data of production order(From Menu Bar).
- The status of production order will be converted from "Released" to "Created".
- Release the production order again.
Thanks
SUMIT

Cancellation of Inspection Lot with Status LOLK

Lot with Origin 08 has the status "ICCO SPCO BRRQ LOLK". Stock has been scrapped through movement type 713 from the quality inspection area but the lot is still is displaying in QA32.
When we are trying to remove the status LOLK through QA12 system is not allowing to enter into screen and giving message "This function cannot be carried out."
How to cancel or remove this lot?

Hi,
status LOLK means Lot locked for batch record
So go to QA32 and select the relevant inspection lot and go to the Usage decision tab.
Click the menu bar " Usage Decision" and go to
Functions-block for batch record---deselect
Then save the lot and come again to functions--- cancel the lot.
By doing this you can cancel your lot
How to cancel or remove this lot?
Hope your problem will sorted out
Give a try and confirm
Regards
Hari

Inspection lot with stock tab for sale return from customer.

Dear,
In our organization there are two scenarios,
1)     Make to order- Strategy group -20
2)     Make to stock- Strategy group -10
I have maintained 05 inspection types in QM view for sale return inspection from customer.
1) In make to order scenario Inspection lot created with inspection stock tab which is OK.
2) But in make stock scenario no inspection lot is generated.
    Remember I donu2019t want inspection lot without inspection stock tab as per insp. type-06
So please suggest me, what can I do for getting inspection lot with stock tab for make to stock scenario.
Regards
Shabbir Kureshi

Hi
QCC0>Quality inspection>Inspection lot creation>Inspection for shipping>Assign Inspection Lot Origin to Delivery Type-->aganist delivery type Enter 05 inspection lot origine
Also in OMJJ check whether QM in active for mnt type 651
Regards
Sujit

Multiple result recording for Manual inspection Lot using inspection point

I want to record inspection result for inspection type 89 against *inspection point*. Then I create new inspection point and assign it in quality plan. Then I have done the multiple result recoding against one manual inspection lot in DEV server. But when it is going to QAS server then error is coming during result recoding. Error is "The results transaction cannot be used for
inspection" Message no. QE094.
Plz give me the solution to record the result.

Reason is very simple : the the inspection point definition in the task list header is incompatible with the sampling procedure assigned to the characteristic.Make sure that you select the appropriete radio button in QDV1 while creating sampling procedure and assign the same against each of the MIC's in the task list.
Make sure that the sample tab in QA02 is pressed while assigning the inspection specification & status of the lot is REL

QM Manual Inspection Lot - with Inspection lot origin 89

Similar Messages

Maybe you are looking for