QM & PM Calibration Process Configuration

Hi
I wanted to configure a calibration process. I have made the settings for PM and QM integration but unfortunately in our implementation QM is not in scope but I need to do the QM settings which will be required for calibration. Can anyone provide me a configuration document for calibration process which contains the settings for QM as well as for PM.
Thanks a lot for help.
Thanks & Regards
Vineet

Dear Vineet,
In QM SPRO you have to assign inspection type 14which is for inspection in plant maintenance. Also you have to maintain number range for this. most of work in calibration belongs to PM only.
Following is the flow:
1) IE01 : Create test quuipment.
2) QDV1: Create sampling procedure for plant mentenance.
3) IP42 : Create maintenance plan for equipment.
4) IA01 : Create equipment task list.
5) IP02 : Assign task list to maintenance plan.
6) IP10 : Schedule maintenance plan.
6) IP30 : Deadline monitoring of maintenance plan.
7) IP24 : Viewing schedule for calibration with order released.
8) QE71 / QE53 : Calibration Result recording and UD.
This is the way i have mapped the calibration process.
Hope this will help you.
BR
Shekhar

Similar Messages

Configuration of calibration process

sir i am new in sap pm.my boss given me a task that how to configure a calibration process in sap pm.i have seen on scn or google but i didn't get any document related to that please help me to configure a calibration process in sap.if you have any pdf or doc file then please share it to me.

Hi
It is a Huge data but Inshort I can tell you
1.Create Equipment using IE01
2.Create task list in IA01/IA05
3.Create Maintainance plan using IP01
schedule the equipment in the same with fix cycle.
4.Schedule through IP30.
Also In customization against PM order define the Inspection lot origin 14
After scheduling Inspec lot of 14 will be created
Then Do RR & DR
This is how it will be used
REgrads
Sujit

How to maintain calibration process in qm

sir,
i am new in qm module n and i m going to implement for qm module.
so pl tell how i maintain qm configuration data n calibration process of qm.

Hi
It is a Huge data but Inshort I can tell you
1.Create Equipment using IE01
2.Create task list in IA01/IA05
3.Create Maintainance plan using IP01
schedule the equipment in the same with fix cycle.
4.Schedule through IP30.
Also In customization against PM order define the Inspection lot origin 14
After scheduling Inspec lot of 14 will be created
Then Do RR & DR
This is how it will be used
REgrads
Sujit

Equipment calibration process

Hi experts,
in equipment calibration process we have created a plan and scheduled.
maintenance order with inspection lot created.Calibration completed and closed.
But for the next calibration due date again we have to save the schedule (IP10)
in order to create maintenace order with inspection lot automatically by the system.
is there any solution for this problem so that we don't have to save the schedule again and again to create maintenance order automatically ? Plz answer.

When you create a maintenance plans for calibration in the third tab you will find sort field, define one sort field specific to calibration in configuration and attach it with your all calibration plans. Now after completing the calibration work don't forget to run the dead line monitoring program. Simple select the sort field and execute it will not take more than a min and all your next planned dates will be adjusted automatically
Regards,
EJ

I have LabView but I do not have the Calibration and Configuration Palette,and I could not download it, how can I download it or if i cannot,can I work with the NI-DAQ Calibration_1200?

I have read in a tutorial for the board 1200 that I can calibrate it with the Calibration and Configuration Palette in LabVIEW, but I do not have them and I could not download it to access its libraries, so I can only download the NI-DAQ software,What's my best choice and if it is to download the palette with its libraries, how can download it with them?I'd appreciate your answers

If you wish to use your 1200 device in LabVIEW, you must download and install NI-DAQ. When you install NI-DAQ, it will ask you if you would like to install support for LabVIEW. By installing this support, you will then have access to the DAQ pallette in LabVIEW. The DAQ pallette requires that you have NI-DAQ installed.
For more information on installing and using your device, you can refer to the DAQ Quick Start Guide. You can download it from:
http://digital.ni.com/manuals.nsf/14807683e3b2dd8f8625677b006643f0/0eca53fe80911b1f862568560068295d
Regards,
Erin

IPC:bute in the field catalogue while processing configuration or pricing i

Hi,
I get this error (Message Class: PRC_MESSAGES_EXT (Messages for Calling Public Pricing Modules), Message Type: E, Message Number 099, Message variables: Message variables 1-4: IPC:bute in the field catalogue while processing configuration or pricing in context spe.condmgnt.customizing.dba.imp.AttributeClassObjectManager.createAttributeClassAttributeClassObjectManager.java)
when we ran IPC userexits.
We've added a field ZZPSTYV in the communication structure and modified the method to define this field like follows:
     public String[] determineRelevantAttributesForRequirement(
          boolean headerAttributes,
          int reqNo) {                         String[] relevantAttributes = new String[0];
     //Header?
     if (headerAttributes) {          }
     //Item
     else {
     //KOMP fields
     switch (reqNo){
          case 900:                              relevantAttributes = new String[] {"ZZPSTYV" };                                   break;
    return relevantAttributes;
Running this code we get the above listed error. Same error if we define unnecessarily a standard field, such as SOLD_TO_PARTY in place of ZZPSTYV.
Can anyone give us some advise as what we did wrong? Appreciate it very much,
Yanhui

Hi Yanhui,
Is it a item field? Remember that mixed fields should be declared at the header in the IPC.
Missing any other requirements?
Cheers
Andrew

Define Tabs and Process Configuration for Template (HAP_TA_CONF)

I am currently building a new appraisal template for my client and I have configured the process timeline in the development system via the IMG node Define Tabs and Process Configuration for Template (transaction code HAP_TAB_CONF).
Does anyone know how to transport the tabs and process configuration through the system landscape?
We are on SAP ECC 6.0 Enhancement Pack 4

Hi Sushil,
I have used the report RHMOVE30 as you recommended and it worked perfectly in one run. I did not have to create custom relationships. I simply selected all the Process Item (VH) objects for my appraisal template and ran the report.
Many thanks for your help. It has saved me having to configure the tabs and process timeline in each client.
Janet

Define Tabs and Process Configuration for Template

Hi All
I would like to give the local HR the ability to define Tabs and Process Configuration for Template
The only way I can find to create these definitions is using SPRO and I don't want to give HR users SPRO
Is there a transaction which will allow the HR users to define Tabs and Process Configuration for Template?
Thanks
Maya

You can try this URL:
http://server.domain:port/sap/bc/webdynpro/sap/hap_configuration?WDCONFIGURATIONID=HAP_AC_TAB_CONF
Just change server, domain and port to match your SAP instance.

JMF Process Configuration

I am working through the guide on JMF, but one of the examples is giving me problems. The lines of code are as follows:
Processor processor = null;
try
    processor = Manager.createProcessor(ml);
catch (IOException e)
    System.exit(-1);
catch (NoProcessorException e)
    System.exit(-1);
//configure the processor
process.configure();
// block until it has been configured
processor.setContentDescriptor(
                                 new ContentDescriptor( ContentDescriptor.RAW ));Ok. Here is the problem as I understand it. configure() is an asynchronous method. So when I get down to setContentDescriptor() the process isn't configured yet and it throws this exception:
javax.media.NotConfiguredError: setContentDescriptor cannot be called before configured
I've seen some people using a function called waitForState(), but when I try to us it the compiler calls it an unresolved symbol. Anyone have a solution for this one?
Thanks,
Khanathor
Message was edited by:
khanathor

Sorry about that, warnerja. I overlooked the JMF section of the forums and the fact that I was crossposting completely slipped my mind. It won't happen again.
Thanks,
Khanathor

Process Configuration

I am working through the guide on JMF, but one of the examples is giving me problems. The lines of code are as follows:
Processor processor = null;
try
    processor = Manager.createProcessor(ml);
catch (IOException e)
    System.exit(-1);
catch (NoProcessorException e)
    System.exit(-1);
//configure the processor
process.configure();
// block until it has been configured
processor.setContentDescriptor(
                                 new ContentDescriptor( ContentDescriptor.RAW ));Ok. Here is the problem as I understand it. configure() is an asynchronous method. So when I get down to setContentDescriptor() the process isn't configured yet and it throws this exception:
javax.media.NotConfiguredError: setContentDescriptor cannot be called before configured
I've seen some people using a function called waitForState(), but when I try to us it the compiler calls it an unresolved symbol. Anyone have a solution for this one?
Thanks,
Khanathor

Sorry about that, warnerja. I overlooked the JMF section of the forums and the fact that I was crossposting completely slipped my mind. It won't happen again.
Thanks,
Khanathor

Doubts on calibration process

Hi,
I AM DOING CALIBRATION PROCESS FOR THE FIRST TIME. The process i followed is:
IE01:Equipment
IP11: Maintainence Strategy
IA05: Task List
IP42: Maintainence Plan
IP10: Scheduling Of plan
IP30: Job Planning
Above this i have assigned Inspection type 14 to PM order type for calibration.
My doubt is:
1) Is the process that I am following is correct.
2) If yes, then after I schedule the orders by IP10, Do i need to relese the orders manually in IP10 or do the orders are made & released automatically when I execute IP30. Please let me know what is the process.
3) If i reject the MIC in result recording does the order still get the status of TECO as it gets when i accept the UD.
4) Do the maintainence orders get generated automatically after executing IP30 automatically.
PLease respond, I will award points.
Regards
Ashish Khurna

hi
Following is the pre requisite for calibration orders.
Maintain the inspection type 014 in customising (done by QM consultant)
Assign Inspection type 014 to order type PM05 in customising.
Maintaing the following master data:
Create Master inspection charecteristics
Maintain sampling procdedure
Tasklist with inspection point as 300 for equipment
Assign inspection charectersitics to operations
Maintain catalogs for results recording / usage decision
Create Maintenance Plan
Schedule the maintenance plan
Calibration orders would be generated
release and inspection lt will be created
Check through Tcode QA32 and process the inspection lot - results recording, usage decision
Trust this may help you.
Regards,
E-Jad

CMDTUX_CAT:754: ERROR: error processing configuration file

Hi Tuxedo Experts,
I have compiled and linked sample code tuxedo client and server (simpapp). According to README, the next steps is running tmboot -y command. Does it start the simpserv tuxedo server? If not, how do I start that?
Plus, when I ran this 'tmboot -y' command, I got the error:
===========================================
$ tmboot -y
tmboot: internal error: CMDTUX_CAT:754: ERROR: error processing configuration file
tmboot: internal error: CMDTUX_CAT:1360: ERROR: configuration file not found
===========================================
Would you please help me to resolve that.
Thanks & Regards,
Ahsan Asghar

Hi Ahsan,
You skipped some steps. One of the first steps is to set the environment variables given in the README. This is normally done by creating a script you can execute in the future, often called setenv.sh. After creating this script and executing like:
. ./setenv.sh
then you need to edit the sample UBBCONFIG file which for simpapp is called ubbsimple. This file contains the Tuxedo configuration information. You will need to replace the things in <> with ones appropriate for your system. The machine name should be the same as the output of the uname -n command.
Once you've edited the file, it needs to be compiled with the tmloadcf command. Then you should be able to boot and run your application.
Regards,
Todd Little
Oracle Tuxedo Chief Architect

Tabs and Process configuration - PMS

Dear Experts,
We're on EHP4 and using flexible performance management system. I would like to know if there is any possibility/settings by which I can uncheck the default tab. i.e. of Element type " Appraisal template" present under the config node "Define Tabs and Process Configuration for Template" .
Regards,
Sachin

Hi Sachin
Did you get the solution for your problem?
I have a similar requirement , is it possible to hide the default Appraisal tab?

Appraisal- "Define Tabs and Process Configuration for template"

Hi Experts,
I am looking for implementation of Flexible template. However, I am unable to do so because "Define Tabs and Process Configuration for template" config node is not available even though we have activated business functions HCM_OSA_CL_1 and HCM_OSA_CL_2. We are in EHP 5 SPlevel 44.
Please help.

1. Check with Business Function CA_HAP_CI_1 ..first go through the documentation of the Business Function.
2.Check with BC Sets is activated or not through tcode SCPR20PR...If it not activated then activate with Tcode SCPR20..
BC Sets for HR
EA-HR-MENU
EA-HR-AKH
EA-HR-IMG
Mohan

Performance Mgmt - Define tabs and process configuration for templates

Hi,
I would like to utlize the feature of process/phase/step configuration for appraisals by the Web Dynpro configuration for tab and process. I choose the "Process Configuration" tab, enter my appraisal template and period, and click "Start Selection". A warning is displayed "No process defined for <my appraisal template>". Clicking on "Add" and no matter what I did, I don't seem to be able to maintain any process/phase/step into the "Configure Available Elements for Process" table. What is the pre-requisite to maintain and configure the Process/Phase/Step(s) ?
How do I maintain the in preparation, in planning etc statuses in here, I created templates using SAP defined templates for ex: templates for performance feedback etc., statuses are maintained in there by default.
Can you please suggest anything?
Thanks
Murthy

>
Munna wrote:
> Hi,
>
> I would like to utlize the feature of process/phase/step configuration for appraisals by the Web Dynpro configuration for tab and process. I choose the "Process Configuration" tab, enter my appraisal template and period, and click "Start Selection". A warning is displayed "No process defined for <my appraisal template>". Clicking on "Add" and no matter what I did, I don't seem to be able to maintain any process/phase/step into the "Configure Available Elements for Process" table. What is the pre-requisite to maintain and configure the Process/Phase/Step(s) ?
>
> How do I maintain the in preparation, in planning etc statuses in here, I created templates using SAP defined templates for ex: templates for performance feedback etc., statuses are maintained in there by default.
>
> Can you please suggest anything?
>
> Thanks
> Murthy
Hi Munny, I am experiencing the same condition. I have released my template and when I go thru the IMG to the 'Define Tabs & Process Configuration' selection I get the browser screen for setting up the tabs and process. I click on the Process tab and see the screen but the New and Delete buttons are not active (grey'ed out). I toggled my review template (cancelled release and re-released) to see if it changed the symptoms but it did not.
All - are there other conditions that must be met before setting up the Process steps vis the IMG ? I have all of the Status/substatus config complete and it shows up in the right side, but I cannot add anything to the left side to define the process.
Chris Thomas
Duke University

QM & PM Calibration Process Configuration

Similar Messages

Maybe you are looking for