QM Recording File Storage Location

I am working on my first QM installation and am a little confused as to what to enter in the Recording File Storage location on the Configuration Setup. This was ordered and planned as a 2 server installation - a base Server and a Recording server. I am running through the Configuration Setup on the Base server and am at the point where I have to define either a Local or External Storage location. So, should this location be a location on the seperate Recording server?

Make sure the drive is formatted Mac OS Extended (Journaled)
1. Quit iPhoto
2. Copy the iPhoto Library from your Pictures Folder to the External Disk.
3. Hold down the option (or alt) key while launching iPhoto. From the resulting menu select 'Choose Library' and navigate to the new location. From that point on this will be the default location of your library.
4. Test the library and when you're sure all is well, trash the one on your internal HD to free up space.
You cannot move the Library to a server of any kind.
See this article
http://support.apple.com/kb/TS5168
for more. Note the comment:
“Additionally, storing the iPhoto library on a network rather than locally on your computer can also lead to poor performance or data loss.”
Regards
TD

Similar Messages

Default File Storage Location

Where does Garageband store the audio data by default?

Okay.
So if I'm trying to email another friend (with Garageband) a song created in GarageBand called "Song 1," I just attach the file called "Song 1" to the email and they should be able to open it in their copy of GarageBand?

Material Master Record - How to remove or delete storage location

Dear all,
Is there a way to remove or delete a storage location accidentally extended via MM01 due to extending the general plant view?
I've tried the following:
1. I've used MM06 to flag the particular storage lcoation for deletion. However, when go to MM02 and select the plant view, the storage location that already been flag still exist for selection. I only get the warning prompt "The storage location has been flag for deletion".
2. I tried MMSC attempt to delete and I get either messages with different material master record:
a) "Material not fully maintained for this transaction/event"
OR
b) "Storage location 60BF already exists and cannot be deleted"
P/S: If this question has been asked before by others, please point me to that thread.
I'm grateful for any suggestion. Thanks.
Steven

Hi Jurgen,
I've gone through the data archiving project in the past. I was actually hoping I don't have to go through this big exercise for this minor situation.
The storage locations in the SAP system are fine. The problem is that when I came in to this organization, I found out that the procurement users have accidentally extended material master record to those storage location irrelevant to them. Those users don't post any stock to those accidentally extended storage location. They admit that it was a mistake. So, I don't really have to do stock movement or GI out from those affected storage location because there's nothing in them.
Now that I've initially flag for deletion (MM06) of those mistakes done by those procurement users over the few years counting to 2000+ material master records affected. But the standard behavior of the SAP system allows change to proceed in MM02 except for that warning message MM081. So, I was actually asking around to explore if there's actually an option to make it an error prompt instead and stop the whole change process at MM02 transaction level.
If I may re-confirm, what I've done so far via flaging for deletion of material master record at storage location level - is this the only correct solution available?
Hope this clarifies my intention of opening this thread. Sometimes, users are quite tough in accepting the results from standard SAP system behavior.
Thanks for the time in explaining.
Steven

Can I change the iPhone backup files storage position?

My C drive is almost full! And iTunes on the iPhone backup file exists by default C drive, can not be changed! D drive I have 20GB of hard disk space, but I am not able to backup file exists D hard disk, what can change the backup file storage location? I do not want there C drive!

This may Help... See here for where backups are stored...
http://support.apple.com/kb/HT4946

Change Software Update Service storage location - OS X Server 2.2

What's the best way to change the file storage location used by the Software Update Service in Server 2.2? I don't want to change the default "Service Data" location for the other services.
Generally I like to make as few changes to the standard configuration as possible, but in this case I need to make an exception. I'd really like to to get the catalog of update files on to an External Pegasus RAID.
I've tried using a symlink to the /Library/Server/Software Update/Data folder. That didn't work as the service was unable to update the catalogs.
Should I use a symlink on the whole /Library/Server/Software Update/ folder or is there perhaps a better way?
With any potential solutions, how likely is is that changes I make likely to be overwritten with future updates.
Thanks,
GRW

Question (please use responses in bold in square brackets)
Response
1
Update went smoothly with NO problems [No]
No
2
Update actually solved existing previous problem with server [Not sure yet]
Not sure yet
3
Updated from Server App version 2.2 [Yes]
Yes
4
If answer to Q.3 was 'No' please advise previous server version [Server app version #]
5
OS X version at the time was 10.8.2 [Yes]
Yes
6
If answer to Q.5 was 'No' please advise previous OS X version [-]
To clarify:
1) As it was updating application data, I got an error message at the very end of the update saying that some application data may not be usable/work/wasn't updated (something to that tune) with a yellow triangle and exclamation mark inside it. After the update, I rebooted the server just in case then let everythign start up normally. All services turned on as per usual.
I have gone through most of my services that I run and I'll list off everything that I've tried out and it's state:
Caching Server - Looks OK
Contacts - Functioning so far as expected
Calendar - Functioning so far as expected
Profile Manager - Was able to test a push profile add and delete with success
DNS - Functioning as normal
Software Update - Looking good so far (I had issues with it stopping and restarting randomly with an interval of a month or two between events, hoping that is fixed, though it never affected functionality - it was in the error logs)
File Sharing - Working as expected
Open Directory - No issues thus far
VPN - Looks OK
Websites - Functioning as expected
Hope that helps you guys!

Purchase info record for PO determine by Storage location

Dear Guru,
Can you please advice when during the creation of PO, is there possible to determine the Purchase info record by the Purchasing Org, material, Vendor as well as "Storage Location".
Reason,
Sometime we need to raise the PO those customer who will be exempted from the governamt VAT or duty which the goods has to delivery to the country Bonded warehouse.
I created 2 Storage location;
1.) 1000 for general WH
2.) 2000 for Bonded Wh
So i would like to know if we can create 2 different info record determine by Storage Location?
Thank you very much,
Regards
Chee Wee

Hi
In Standard SAP it is not possible

LSO 600 Configuration - Central Storage Location for XSLT Files

Hi,
We are implementing LSO 600 with enhancement pack 2 and I am haiving trouble figuring out what do do with the configuration steps
Enter Address of Central Storage Location for XSLT Files
and
Enter Address of Central Storage Location for Templates.
The config notes indicate that these can be a directory or network path with the format
servername\filename\.
As I understand it this is is the address of the file on the Portal Server where XSLT files and templates be stored. The problem that I am hearing from the basis team is (I am qouting an email from them) "who accesses the share? Is it the server, the client PC or both? Were running in a linux environment so I dont have any shares the PC can access."
Does anybody have any input?
Thanks,
Andy

Hi Andy!
I am happy that the issue is already clear!
Beeing busy makes life more interesting )
May I ask for your private mail, because I had some questions regarding your LSO implementation.
Mine is:
[email protected]
Thx in advance and have a nice day!
best regards,
Zsolt
P.S.: since I am a Moderator for SDN it is my job to keep the rules on the Forum therefore I would like to ask you to close this thread because the question - as you stated - is answered.
Thank you!

IPhone backup storage locations (notes, files, email signatures, etc.)?

how does one back up notes, files, and email signatures on an iPhone? Where are they stored on a Mac. Does it all go into my iTunes library?

The backup file that iTunes makes stores that information. The file is located in ~/Library/Application Support/Mobile Sync/Backup. This file is not easily readable, but is the file used when you restore your phone from backup. This Apple article explains the backup: http://support.apple.com/kb/HT1766
To find a utility to get information from the backup file, do a Google search for "backup extractor Mac".

Quality Management v9 - Recording file is .spx and size of 0 kb

Guys,
I have theses versions here :
CUCM v9.1.2
Quality management 9.0.1.57
UCCX 9.0.2.11001-24
Desktop are connected on the PC port of the phone !
I want to do the desktop recording and I have an issue where the storage location contains only .spx files that are empty with 0 bytes.
Here is the troubleshoot I did :
From the Recording interface I can see all the conversation but I can't play it.
If I use wireshark I can see the RTP on the destop, I can convert it and listen that RTP stream..so the stream is going to PC
If I run the QMDump on the desktop of the agent I see the G711 Ulaw which is good but I can't find Skinny hearts beats ( logs of QMdump Attatch ).. I rebooted the phone but still..
I see on the troubleshooting guide, that this situation could be during the conversion process, it says we need to get logs and escalate the case.
Anyone have a suggestion ?

Mary,
this issue pertains to either not receiving a SIP invite to start recording, or not receiving the actual RTP from the phone. More than likely it is not receiving a SIP invite. Check the (WFO 9.0 "Recordserver.dbg") or (WFO 10.0 "Ctiservice.dbg") logs , look for INVITE, it should tell you if you received it or not.
Example of a good SIP invite:
SIP: IN|INVITE sip:[email protected]:5060 SIP/2.0|6156255c|10.192.252.36:32880->10.32.2.66:5060|Call-ID: [email protected]|From:
Example of a BAD SIP response:
type=Network Recording,person=140]] call CiscoCall[Call[2:20211600];ConnectionId=31651532] should have received SIP but didn't!
If you are getting a SIP invite, then check the ports between Phone and Recordserver to ensure RTP can get through.
If you are NOT getting a SIP invite, check your CUCM configuration for Recording:
here is a link to guide you.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/admin/6_0_1/ccmfeat/cmfsgd601/fsmr.html#wp1047595

Archiving material master - storage location

Hi experts,
I am in process of archiving storage locations of few material codes which are split valuated.
Actually material/s are extended to 3-4 storage location and one storage location has to be removed from the same.
i am using transaction code SARA with archiving object MM_MATNR and getting following error -
plant/storage location dependent batch records exist.
please suggest how to correct the error
relevant solution will suitably be rewarded please.
regards,
Pawan Khurana

I had not spoken about the tick for delete in test mode in the selection screen.
I spoke about the variants for test and production run in customizing to your archiving object.
If the variant that is saved for production run, has the tick for test run, then it just will not work.
Further you should select X Complete for Detail log and list for P_PROT_O,
This way you should get spool file that tells you more about errors or succesfull archived items.
What did you do with the box in from of "Consider batch record without deletion flag" ?
If empty, are you sure you have manually set the deletion indicator in MSC2N?
What about the other boxes in this options section?

DataBase Tables for fetching storage location text

Hi All,
May I know the database tables used for storing storage location text.
Regards
Nikhil
Moderator message: please do some research before asking.
Edited by: Thomas Zloch on Mar 14, 2011 9:22 AM

Dear Jaques,
Check in these tables,
SER00                        General Header Table for Serial Number Management
SER01                        Document Header for Serial Numbers for Delivery
SER02                         Document Header for Serial Nos for Maint.Contract (SD Order)
SER03                         Document Header for Serial Numbers for Goods Movements
SER04                          Document Header for Serial Numbers for Inspection Lot
SER05                          Document Header for Serial Numbers for PP Order
SER06                          Document Header for Serial Numbers for Handling Unit-Content
SER07                          Document Header for Serial Numbers in Physical Inventory
EQBS                         Serial Number Stock Segment
EQKT                           Equipment Short Texts
EQSE                           Serial Number Records
EQST                           Equipment to BOM Link
EQUI                           Equipment master data
EQUK                           Quota File: Header
EQUP                           Quota File: Item
EQUZ                           Equipment time segment
Regards
Mangalraj.S

Mc.9 Multiple storage location issues

Hi,
I am fetching data from mc.9 in my program but if the use enter multiple storage in selection only 1st value is printed following is code and how will i come to know which material is for which storage location since mc.9 data is not getting stored anywhere
SELECT-OPTIONS : SLOC LIKE S031-LGORT.
SUBMIT RMCB0300 WITH SL_WERKS-LOW = PLNT
                    WITH SL_LGORT IN SLOC
                  WITH SL_MTART = 'HALB' WITH SL_MTART = 'VERP'
                    WITH SL_MTART = 'ROH' WITH SL_MTART = 'FERT'
                    WITH SL_SPMON-LOW = FPERIOD
                    WITH SLV_NO = 'STK'
                    WITH SL_SPMON-HIGH = FPERIOD EXPORTING LIST TO MEMORY AND RETURN.
while append to internal table even if i specify both high and low value it prints low and high incorrectly how will this problem will solved
itab-lgort = sloc-low.
Help required for same.
Thanks
Shruti

Hi Shruti,
I simulated the code given by you and all the storage locations are being populated in the backed.
You can check this by putting a breakpoint at the below code in RMCB0300 and checking the value of sl_lgort[]. You will receive the number of SLOC inputs provided.
AT SELECTION-SCREEN OUTPUT.
FLG_FOUND = FALSE.
PERFORM SPEZIAL_AT_SELECTION_SCREEN_O IN PROGRAM (LIS_PROGNAME)
                                        CHANGING FLG_FOUND
                                        IF FOUND.
This is a data issue and you may not have any records for the selected input.
Regards,
Jovito.
Edited by: dsouzajovito on Dec 29, 2010 5:56 AM

Valuation at Storage Location Level

Dear Experts ,
We need to transfer Stock from Storage Location to another Storage Location. MVT 311
The problem is that we want the system to create Financial Document during this step, And as we know valuation is on Company Code or Plant Level .
So What help us to execute this is it profit center or Business Area or what ?
Please Advice

Hi,
Try this,
You can follw this following process for Stock Transfer between Depots (locations):
Material should exist in both the plants (Delivering & Ordering),
Internal customer should be assigned to the ordering plant ( MM -> Purchasing -> Purchase Order -> Setup stock transport order -> assign the internal customer to the ordering plant and assign the Sales area of the internal customer)
T-code : OMGN
Assign its Sales area to the delivering plant
Assign the document type and Delivery type NB and NLCC
Assign the Supplying plant --> Receiving Plant --> NB
Take the delivering plant and assign the sales area.
Vendor master has to be created and assign the supply source ( Delivering Plant).
Create a purchase order ME21N (Purchasing Document type UB)---> Save
Delivery - VL10 B ---> Calculation rule (appropriate) --> Assign the purchase order number here and execute.
Select the Delivery creation line and do the back ground process.
Start the log display and see the delivery document number by the documents button
Go to VL02N --> do picking and PGI --> Then do the MIGO with respect to the delivery document.
Subsequently yopu can also issue stock transfer Invoice (which is treated as Proforma Invoice & not posted in accounts) for records or to be given with vehicle.
Hope this helps...
Regards
KK

Material/Serial Nbr is "Stuck" in a storage location and can not be moved

We have a situation created by my customers which has lead to a situation I have never seen before. A material/serial nbr. that is in our Returns location that can not be transfered, issued, removed, or anything via ANY MIGO movement type combination.
This is what happend:
- Customer return processed. Material ABC, Batch XYZ with Serial Nbr. 123 brought into our "RT" StoreLoc.
- Clerk processed MIGO to do a Stock Transfer of this material to another StoreLoc. (PS). He entered in the material ABC, batch XYZ, and a bad serial number 1233. He used a 453 Movement type.
- After realizing his mistake, he processed MIGO again and processed a GI Xfer posting with a 972 movement type to get rid of the bad material/serial nbr. he had just moved to the PS StoreLoc.
- Then he tried to redo the Stock Transfer using a 453 Movement type for the material ABC, batch XYZ, and the good serial nbr. 123, but, he gets a "Deficit of BA Ret.blocked prev. 1.000 EA " error message.
- At this point, he contacts me to ask what can be done.
No matter what we try to do, we can not access this part/serial nbr. combo to move it or issue it or whatever. It is like a ghost now. You can see the serial number via IQ03, but you can not do anything with this part/serial nbr.
Help! Do I need to write an ABAP to physically delete this material/serial nbr from its batch?

Hi,
First of all, I would assume you used customized movement type 972 to 'get rid of' your material ID with wrong serial number 1233 at PS storage location. If this is the case, then this posting did not return the stock quantity from PS to your RT storage location and that why when you tried to make another posting (with correct serial number 123), an error message was popped up as you simply do not have available stock. The solution in this case are -
1)   Cancel the posting that you made previously with movement type 972. This cancellation will help return your stock (though with wrong serial number 1233) to PS storage location;
2)   Cancel the posting that you have posted to move your stock back from PS to RT (again with wrong serial number). This steps ensure the stock quantity '1' is available at RT storage location;
3)   Make another stock transfer (with correct movement type 453 and serial number 123) from RT;
4)   Delete the serial master record 1233 so that it can no longer be used.
Cheers,
HT

Inspected stock posting to multiple storage location without batch

Hi,
At the time of Usage Decision, I want to post the inspected stock to multiple storage location i.e., Rejected Stock to Scrap Storage Location, Qualified Stock to Unrestricted Use Storage Location.
Quick response will be appreciated.
Anandkumar KS

The scrap line has no storage location since that stock is typically written off and scrap cost center is defined in configuration.
A possible alternative is to set up VMENGE08 and VMENGE09 with the same material movements you want to use. You obviously aren't using the 553 movement type as that writes off the material. That could give you two lines to use for your scraping. I can't remember if these stock posting lines give you the storage location option or not and I don't have a sandbox available to test today. If you need to post more then two grades in one inspection lot, you'll have to do the first two postings, save the UD, then come back in and do a second posting for the next two grades.
Read the configuration help file you'll find in confg for "Define Inventory Postings" under the QM config.
You can also change the displayed names of the stock posting lines. That's explained in the config file as well.
Craig

QM Recording File Storage Location

Similar Messages

Maybe you are looking for