QoS Problem - Outbound Ethernet Marcation
Hi all,
I have a problem with QoS.
Everytime a voice packet go outbound through an Ethernet interface the router remove the DSCP marcation 46 (EF) and marks as 0. Serial interfaces work fine.
I've tried with different IOS versions but the problem is the same.
If anyone has faced this problem before, please let'me know what IOS version this QoS configuration work.
Cheers ///
Neirival de Sousa (Brazil/Angola)
Hi,
can yo be more specific about your hardware/software and general setup?
Also one more thing: are you sure it happens outbound? Could it be that a LAN switch is receiving the frame/IP packet and the default port settings for Catalysts kick in? QoS wise all LAN ports on the Catalyst switches are untrusted, thus any marking will be set to 0 (best effort), when received on such a port. You need to issue a "mls trust ..." command on each port, where markings should be passed unchanged. The "..." is "cos" or "dscp" and depends on hardware/IOS.
Hope this helps! Please rate all posts.
Regards, Martin
Similar Messages
-
ASR1001 QOS Problem %QOS-4-TUN_MOV_FAIL
Dear member,
I have facing a problem on the ASR with QOS problem, I configured a hqos on phyical interface and hqos on tunnel interface, the number of tunnel about 350.
I check on the logging, the QOS on tunnel was continues fail and install.
============================================
%QOS-6-TUN_INSTALL: Installing suspended policy on Tunnel2000.
%QOS-4-TUN_MOV_FAIL: Queueing hierarchy move failed on Tunnel2780, suspending policy.
%QOS-4-TUN_MOV_FAIL: Queueing hierarchy move failed on Tunnel2000, suspending policy.
%QOS-6-TUN_INSTALL: Installing suspended policy on Tunnel3080.
%QOS-4-TUN_MOV_FAIL: Queueing hierarchy move failed on Tunnel3080, suspending policy.
%QOS-6-TUN_INSTALL: Installing suspended policy on Tunnel2380.
%QOS-4-TUN_MOV_FAIL: Queueing hierarchy move failed on Tunnel2380, suspending policy.
%QOS-4-TUN_MOV_FAIL: Queueing hierarchy move failed on Tunnel70, suspending policy.
%QOS-6-TUN_INSTALL: Installing suspended policy on Tunnel2140.
============================================
Any member have this experience.
Attach the QoS configuration for reference.
Regards
RussSeem not related to this bug as ASR only suspended policy without reboot.
Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.2(4)S, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Mon 23-Jul-12 20:03 by mcpre
IOS XE Version: 03.07.00.S
License Level: adventerprise
License Type: Permanent
Next reload license Level: adventerprise
cisco ASR1001 (1RU) processor with 1156392K/6147K bytes of memory.
Processor board ID SSI170805JC
4 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
7741439K bytes of eUSB flash at bootflash:.
Configuration register is 0x2102 -
So I have a wierd problem.
Sometimes the ethernet port is working, sometimes not.
I've tested the ethernet cable and it works perfect with other computerS.
I've tested my macbook pro with other ethernet cables and the problem still occurs.
I've tested the ethernet plug (in the wall) and it works pefect with other computerS.
So only last potential problem : the ethernet plug / card IN my macbook pro.
It is a 2.8 Ghz Intel Core i7 with 8 Gb of 1067 Mhz DDR3 RAM, and OS X 10.7.4.
The problem is just random... sometime it works, sometime it doesn't... sometimes it works, and stop working... sometimes it works for days without problems... sometimes it doesn't work for days, with nothing to do.
Can anyone help? I don't think I'm on the warranty anymore... so before I go drop my MBP at an Apple Store, I want to make sure I've tryed everything.
Especially for the price I paid for this MBP, can't believe I'm hustling with such a basic feature......
THANKS FOR THE HELP!!!I've used the reset chache solution with mixed success. I finally tripped over something that actually works every time. The "secret" seems to be getting the apply button active when you are on the "location" where the ethernet connection is configured. Here is what I did.
move the ethernet connection configuration to another "location" within network preferences. I called mine Home Wired.
When the cable disconnected situation occurs, switch to the location that has wireless and enable wireless. Now turn it back off.
Switch to the wired location and highlight the wired configuration and click apply. It goes through the steps of acquiring an IP and then you are connected.
Easy peezy -
I have Power Mac G5 1.8 single. I have a problem with ethernet port, before it was working with the internet, but now i shows it is connected even the cable is disconnected. I'm running Leopard 10.5. any help
Reset the PRAM.
http://support.apple.com/kb/HT1379
If that fails, reset the PMU.
Scroll down the following page and click the G5 link for instructions:
http://support.apple.com/kb/ht1939 -
Dears
I want your help in figuring out the problem in configuration, as I am trying to deploy qos on DMVPN
# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb Target Network
1 172.23.1.5 172.23.11.5 UP 00:16:57 D 172.23.11.5/32
NHRP group: spoke_group1
Output QoS service-policy applied: none
AUBEgypt-RHT-R this router is hub
shooting club is spoke
but i can't see the result as expected :
AUBEgypt-RHT-R#show dmvpn detail
Legend: Attrb --> S - Static, D - Dynamic, I - Incomplete
N - NATed, L - Local, X - No Socket
# Ent --> Number of NHRP entries with same NBMA peer
NHS Status: E --> Expecting Replies, R --> Responding
UpDn Time --> Up or Down Time for a Tunnel
==========================================================================
Interface Tunnel172 is up/up, Addr. is 172.23.11.1, VRF ""
Tunnel Src./Dest. addr: 172.23.1.1/MGRE, Tunnel VRF ""
Protocol/Transport: "multi-GRE/IP", Protect "IPSEC_PROFILE"
Interface State Control: Disabled
Type:Hub, Total NBMA Peers (v4/v6): 1
# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb Target Network
1 172.23.1.5 172.23.11.5 UP 00:16:57 D 172.23.11.5/32
NHRP group: spoke_group1
Output QoS service-policy applied: none
Crypto Session Details:
Interface: Tunnel172
Session: [0x689D0324]
IKE SA: local 172.23.1.1/500 remote 172.23.1.5/500 Active
Capabilities:D connid:1004 lifetime:23:44:18
Crypto Session Status: UP-ACTIVE
fvrf: (none), Phase1_id: 172.23.1.5
IPSEC FLOW: permit 47 host 172.23.1.1 host 172.23.1.5
Active SAs: 4, origin: crypto map
Inbound: #pkts dec'ed 127 drop 0 life (KB/Sec) 4514806/113
Outbound: #pkts enc'ed 127 drop 0 life (KB/Sec) 4514807/113
Outbound SPI : 0xA67C0EBD, transform : esp-aes esp-sha-hmac
Socket State: Open
Pending DMVPN Sessions:
AUBEgypt-RHT-R#show ip nhrp
172.23.11.5/32 via 172.23.11.5
Tunnel172 created 00:17:17, expire 01:42:42
Type: dynamic, Flags: unique registered
NBMA address: 172.23.1.5
Group: spoke_group1
Shooting-Club#show dmvpn detail
Legend: Attrb --> S - Static, D - Dynamic, I - Incomplete
N - NATed, L - Local, X - No Socket
# Ent --> Number of NHRP entries with same NBMA peer
NHS Status: E --> Expecting Replies, R --> Responding
UpDn Time --> Up or Down Time for a Tunnel
==========================================================================
Interface Tunnel1 is up/up, Addr. is 172.23.11.5, VRF ""
Tunnel Src./Dest. addr: 172.23.1.5/MGRE, Tunnel VRF ""
Protocol/Transport: "multi-GRE/IP", Protect "IPSEC_PROFILE"
Interface State Control: Disabled
IPv4 NHS: 172.23.11.1 RE
Type:Spoke, Total NBMA Peers (v4/v6): 1
# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb Target Network
1 172.23.1.1 172.23.11.1 UP 00:17:48 S 172.23.11.1/32
Interface Tunnel2 is up/up, Addr. is 172.23.22.5, VRF ""
Tunnel Src./Dest. addr: 172.23.2.5/MGRE, Tunnel VRF ""
Protocol/Transport: "multi-GRE/IP", Protect "IPSEC_PROFILE"
Interface State Control: Disabled
IPv4 NHS: 172.23.22.1 RE
Type:Spoke, Total NBMA Peers (v4/v6): 1
# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb Target Network
1 172.23.2.1 172.23.22.1 UP 00:17:48 S 172.23.22.1/32
Crypto Session Details:
Interface: Tunnel1
Session: [0x669AD6D4]
IKE SA: local 172.23.1.5/500 remote 172.23.1.1/500 Active
Capabilities:(none) connid:1007 lifetime:23:43:28
Crypto Session Status: UP-ACTIVE
fvrf: (none), Phase1_id: 172.23.1.1
IPSEC FLOW: permit 47 host 172.23.1.5 host 172.23.1.1
Active SAs: 2, origin: crypto map
Inbound: #pkts dec'ed 134 drop 0 life (KB/Sec) 4437700/52
Outbound: #pkts enc'ed 133 drop 1 life (KB/Sec) 4437700/52
Outbound SPI : 0x90A47368, transform : esp-aes esp-sha-hmac
Socket State: Open
Interface: Tunnel2
Session: [0x669AD5E4]
IKE SA: local 172.23.2.5/500 remote 172.23.2.1/500 Active
Capabilities:(none) connid:1008 lifetime:23:43:29
Crypto Session Status: UP-ACTIVE
fvrf: (none), Phase1_id: 172.23.2.1
IPSEC FLOW: permit 47 host 172.23.2.5 host 172.23.2.1
Active SAs: 2, origin: crypto map
Inbound: #pkts dec'ed 133 drop 0 life (KB/Sec) 4409710/55
Outbound: #pkts enc'ed 133 drop 1 life (KB/Sec) 4409710/55
Outbound SPI : 0xEEC2E783, transform : esp-aes esp-sha-hmacDears
I want your help in figuring out the problem in configuration, as I am trying to deploy qos on DMVPN
# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb Target Network
1 172.23.1.5 172.23.11.5 UP 00:16:57 D 172.23.11.5/32
NHRP group: spoke_group1
Output QoS service-policy applied: none
AUBEgypt-RHT-R this router is hub
shooting club is spoke
but i can't see the result as expected :
AUBEgypt-RHT-R#show dmvpn detail
Legend: Attrb --> S - Static, D - Dynamic, I - Incomplete
N - NATed, L - Local, X - No Socket
# Ent --> Number of NHRP entries with same NBMA peer
NHS Status: E --> Expecting Replies, R --> Responding
UpDn Time --> Up or Down Time for a Tunnel
==========================================================================
Interface Tunnel172 is up/up, Addr. is 172.23.11.1, VRF ""
Tunnel Src./Dest. addr: 172.23.1.1/MGRE, Tunnel VRF ""
Protocol/Transport: "multi-GRE/IP", Protect "IPSEC_PROFILE"
Interface State Control: Disabled
Type:Hub, Total NBMA Peers (v4/v6): 1
# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb Target Network
1 172.23.1.5 172.23.11.5 UP 00:16:57 D 172.23.11.5/32
NHRP group: spoke_group1
Output QoS service-policy applied: none
Crypto Session Details:
Interface: Tunnel172
Session: [0x689D0324]
IKE SA: local 172.23.1.1/500 remote 172.23.1.5/500 Active
Capabilities:D connid:1004 lifetime:23:44:18
Crypto Session Status: UP-ACTIVE
fvrf: (none), Phase1_id: 172.23.1.5
IPSEC FLOW: permit 47 host 172.23.1.1 host 172.23.1.5
Active SAs: 4, origin: crypto map
Inbound: #pkts dec'ed 127 drop 0 life (KB/Sec) 4514806/113
Outbound: #pkts enc'ed 127 drop 0 life (KB/Sec) 4514807/113
Outbound SPI : 0xA67C0EBD, transform : esp-aes esp-sha-hmac
Socket State: Open
Pending DMVPN Sessions:
AUBEgypt-RHT-R#show ip nhrp
172.23.11.5/32 via 172.23.11.5
Tunnel172 created 00:17:17, expire 01:42:42
Type: dynamic, Flags: unique registered
NBMA address: 172.23.1.5
Group: spoke_group1
Shooting-Club#show dmvpn detail
Legend: Attrb --> S - Static, D - Dynamic, I - Incomplete
N - NATed, L - Local, X - No Socket
# Ent --> Number of NHRP entries with same NBMA peer
NHS Status: E --> Expecting Replies, R --> Responding
UpDn Time --> Up or Down Time for a Tunnel
==========================================================================
Interface Tunnel1 is up/up, Addr. is 172.23.11.5, VRF ""
Tunnel Src./Dest. addr: 172.23.1.5/MGRE, Tunnel VRF ""
Protocol/Transport: "multi-GRE/IP", Protect "IPSEC_PROFILE"
Interface State Control: Disabled
IPv4 NHS: 172.23.11.1 RE
Type:Spoke, Total NBMA Peers (v4/v6): 1
# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb Target Network
1 172.23.1.1 172.23.11.1 UP 00:17:48 S 172.23.11.1/32
Interface Tunnel2 is up/up, Addr. is 172.23.22.5, VRF ""
Tunnel Src./Dest. addr: 172.23.2.5/MGRE, Tunnel VRF ""
Protocol/Transport: "multi-GRE/IP", Protect "IPSEC_PROFILE"
Interface State Control: Disabled
IPv4 NHS: 172.23.22.1 RE
Type:Spoke, Total NBMA Peers (v4/v6): 1
# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb Target Network
1 172.23.2.1 172.23.22.1 UP 00:17:48 S 172.23.22.1/32
Crypto Session Details:
Interface: Tunnel1
Session: [0x669AD6D4]
IKE SA: local 172.23.1.5/500 remote 172.23.1.1/500 Active
Capabilities:(none) connid:1007 lifetime:23:43:28
Crypto Session Status: UP-ACTIVE
fvrf: (none), Phase1_id: 172.23.1.1
IPSEC FLOW: permit 47 host 172.23.1.5 host 172.23.1.1
Active SAs: 2, origin: crypto map
Inbound: #pkts dec'ed 134 drop 0 life (KB/Sec) 4437700/52
Outbound: #pkts enc'ed 133 drop 1 life (KB/Sec) 4437700/52
Outbound SPI : 0x90A47368, transform : esp-aes esp-sha-hmac
Socket State: Open
Interface: Tunnel2
Session: [0x669AD5E4]
IKE SA: local 172.23.2.5/500 remote 172.23.2.1/500 Active
Capabilities:(none) connid:1008 lifetime:23:43:29
Crypto Session Status: UP-ACTIVE
fvrf: (none), Phase1_id: 172.23.2.1
IPSEC FLOW: permit 47 host 172.23.2.5 host 172.23.2.1
Active SAs: 2, origin: crypto map
Inbound: #pkts dec'ed 133 drop 0 life (KB/Sec) 4409710/55
Outbound: #pkts enc'ed 133 drop 1 life (KB/Sec) 4409710/55
Outbound SPI : 0xEEC2E783, transform : esp-aes esp-sha-hmac -
Middleware problem -Outbound queue is stuck in SAP R/3 system with message
Hi Middleware gurus ,
We are stuck with a serious issue . We are trying to download Business partners from SAP R/3 4.6c system to SAP CRM 5.2 system using CRM Middleware
Previously we did a successful Initial download of 2 Business partners from SAP R/3 to CRM . Their BP numbers in CRM are 001 and 002 . The Delta load is working fine for the both the BPs which are already downloaded
Now , the real problem is when we are trying to download a new Business partner . When we set the Filter ( BP no 003 ) in MW adaptor object CUSTOMER_MAIN and start the Initial load again , we see that the Outbound queue is getting stuck with message STOP .
There are two queues generated in SAP R/3 system with names MASS_CRM_CUSTOME and R3AD_CUSTOME . The status for both the queues is STOP and when go for details it mentions sapsuck ..SAPMSSY1 -Message no. SR 053.
Even we checked the txn SMW01, the Bdocs message is "Recived ( Intermediate state) " for Bdoc type BUPA_MAIN.
We really dont as to why the Initial load worked fine with 2 BPs and later when want to do more BP Initial Load the Outbound queue is getting stuck
Also , by unlocking the 2nd queue R3AD_CUSTOME we are able to release it , but the first queue MASS_CRM_CUSTOME* is stuck
Please help us urgently
Regards
Dinesh and Ritvij
Email : [email protected]
Mobile -+91=9704933315Hi Praveen and other Middleware gurus,
We checked on this . Actually the RFC is used for connecting to SAP R/3 system.
We also raised an OSS message on this and found a reply that in transaction CRMM_BUPA_MAP, we can map the required BP . But the SAP support guy recived an error received the error:
An RFC link is not maintained in the Middleware
Message no. CRM_BUPA_MAPPING051
We have set the RFC link , but still the problem continues!!!
Please help further..
Regards
Dinesh and Ritvij -
Z77A-GD65 Problems with Ethernet (Intel 82579V) Code 10 and 55 error
it is just a day with disaster. I bought Z77A-GD65 yesterday, and now it almost driver me crazy , i have two most famous problem of the board ,the CODE10 and ERROR 55!!!
after i bought this board to home ,i spend few hour to figure out the reason why the system can not be booted.
the DIMM SLOT 3&4 of my board is malfunction,no matter what combination i use (1&3,2&3, 3&4...etc),but it works for 1 and 2(i have 4 ram sticks,all of them is fine)
i do upgrade to BIOS 10.5(thx god ,i have two computer ,otherwise i cant even do it because of following issue)
after i solve the problem by only plug in 2 ram (DIMM1&2), succeed to boot up, a new problem occurred to me ,the CODE10!
latest driver , clean system install ,cmos cleaned, does not help.
i have read this thread for code10
https://forum-en.msi.com/index.php?topic=158591.msg1167303#msg1167303
and for error55
https://forum-en.msi.com/index.php?topic=158224.0
it seems the best way to solve it is RMA.
I notice that there is an Authorized Motherboard Repair Center (East Coast):
361 Alden Road
Markham, Ontario, L3R 3L
i live in Toronto, can i just go there and give the board to them to fix it or i can only mail it?
If i need to mail it ,what should i do?Code 10 means the device cannot start. You have the right driver for the Intel 82579V is shorted by either a motherboard screw or a raiser under it. The ethernet adapter has lights which light up id driver is installed (even though code 10 is in effect).
Solution: Remove 1 or 2 motherboard screws and turn the pc on. Repeat until you find out which screw caused the issue. For me it was the screw closest to the ethernet controller.
The wa i fixed it was I was used a plastic washer and I was still able to have the motherboard screw in and at the same time not get code 10 anymore and my Intel 82579V worked fine since. -
Windows 7 Home Sharing Problem (wireless/ Ethernet)
Hello
I spent a few days trying to figure out why home sharing didn't work. I've got 2 windows 7 pc. So comptuer A can detect computer B iTunes library but computer B cannot detect computer A library although the settings such as allow sharing on iTunes preferences are all checked.
Comptuer A was connected using ethernet cable and computer B was using wireless. Both are desktop at different location of the house connected to the same network.
So when I insert an wireless adaptor to Comptuer A and conects it wirelessly to my router, the homesharing appears. Whereas when i connect it with an ethernet cable, it fails.
Is there anyway to troubleshoot this issue?
ThanksI was able to resolve my issue. Here's how:
Did a lot of research on this. I have a Linksys WRT120N router where the only device not on Wifi was my Windows 7 PC (it was plugged in with an Ethernet cable while everything else was on Wifi). Having fiddled with the router settings to no avail, I went out and bought a Wireless USB adapter to put the Windows 7 PC on Wifi.
When I set that up, I could now see my Windows 7 library on the Apple TVs. However, when I went into the library, it was stuck on "Loading Library" in perpetuity.
I looked in my list of Windows services running (Start -> Control Panel -> Search for "Services") and noticed that, even though I disabled the Windows Firewall in the System and Security settings, the Windows Firewall service was still running. I disabled the service (right click -> properties) and restarted the computer. Voila, it works now.
It is possible that the problem was the Windows Firewall service (not the Wireless), but I've read countless posts where people had issues with the devices being on wired and Wifi and not seeing each other. As such, I haven't (and don't plan to) tested it back with just the Ethernet cable. If you're having my issue, you can try that first.
I should also note that when this wasn't working, I was also unable to use my iPhone to pair as a remote with iTunes. It would pair but the iPhone would be stuck in "Looking for" when I tried to control the library. This is now also fixed after doing the above.
Hope this helps anyone else frustrated out there. -
Windows 8.1 Upgrade problem with Ethernet on a Flex 15
Windows 8 was upgraded to Windows 8.1 Upgrade on a Flex 15.
The first time I tried to do the upgrade, I had enough problems that I re-installed from a Windows 8.1 image. All went well and all the drivers work except the Ethernet. The upgrade was relatively painless if you ignore the necessary reboots.
The latest Ethernet driver was downloaded from Lenovo and it was upgraded through Device Manager to version 8.26.218.201
In spite of Device Manager saying the Realtek ethernet adapter is working, no network is recognized by Networks and Sharing Centrewith when an ethernent cable is plugged into the Flex 15 i. The cable is good and has been checked by way of another computer.
I have previously used the hard-wired ethernet once and it worked but I do not remember where the laptop stood during the pgrade path.
This may be a hardware problem which will require mailing the laptop for the repair, or it may be a software / dirver issue.
If anyone has a suggestion, please let me know. The only other thing I can do is reistall from scratch to confirm it is a hardware problem.
With thanks in advance.
Solved!
Go to Solution.OK So I'm not the smartest cookie in the cookie jar.
The Ethernet worked all along, but I inserted the ethernet cable UP-SIDE-DOWN. The Flex 15 has a 1/2 size ethernet female plug and it has a small cover which flips down. This is to allow the adapter in a thin shell
The male end can be plugged in upsidedown unlike a normal-sized ethernet female. It goes in, but does not click. So a word to the wise ... the plastic prong of the male end is on the bottom. -
Problems with Ethernet controller and PCI device driver on Satellite L30-10X
Hellow!
Sorry for my bad English, I'm from Russia.
Just few days ago I bought Satellite L30-10X with W Vista on board. My opinion, that this OS does't very good on this computer, so I install W XP.
I have some problems with drivers. At first, I dont know what model I have:PSL30 or PSL33? I download all drivers for both models. But, after installation, computer doen't find drivers for Ethernet controller and PCI device...Hi
Satellite L30-10X belongs to the PSL33E series. This number can be found on the label placed on the bottom of the unit!
You have to choose this number from the driver download form to get the compatible XP drivers.
I dont know why you are not able to install the LAN driver. Ive got the same notebook with Vista and Ive installed the XP and all drivers run fine.
I assume you have installed the drivers in wrong order. Please take the look in the Toshiba installation instruction txt file. In this order you have to install the driver! Its important.
I think you should install the XP again to ensure the clean registry and then download and install the compatible XP drivers like mentioned in the installation instruction file.
Good luck -
I had a connect with 2 computers - pc and macbook. I often switched cable between them and one day connect on macbook disappeared and it still disappears. But connect on pc is ok and I don't know what is a problem - or it's a bad cable, or it's a bad ethernet-adapter. Does anybody know what I must doing?
p.s. sorry with english, I don't know it very goodBut I haven't a modem - just a cable, which plugs into ethernet port. And macbook says that cable isn't plugged in, but it can't be true!! Later all was ok and I had a good connect!
-
QOS problem (multicast) with 3750
Hi,
I need help to solve following problem.
I have setup qos in our 3750, see below.
Unicast traffic is handle correct, However with multicast streams the router set the dscp to 0
Has somebody any idea what is missing?
Too old sw? Cisco IOS Software, C3750 Software (C3750-ADVIPSERVICESK9-M), Version 12.2(35)SE,
Regards Niklas
ip multicast-routing distributed
ip multicast multipath
mls qos srr-queue input priority-queue 1 bandwidth 10
mls qos srr-queue input dscp-map queue 1 threshold 1 46
mls qos srr-queue input dscp-map queue 2 threshold 1 11 24 30 48
mls qos srr-queue output dscp-map queue 1 threshold 1 48
mls qos srr-queue output dscp-map queue 2 threshold 1 46
mls qos srr-queue output dscp-map queue 3 threshold 1 40
mls qos srr-queue output dscp-map queue 4 threshold 1 11 24 30
mls qos
interface GigabitEthernet1/0/22
switchport access vlan 41
switchport mode access
load-interval 30
srr-queue bandwidth share 25 25 25 20
priority-queue out
mls qos trust dscp
interface GigabitEthernet1/0/23
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 40
switchport mode trunk
load-interval 30
srr-queue bandwidth share 25 25 25 20
priority-queue out
mls qos trust dscpHi,
Here comes the printouts:
with mls qos enabled:
cisco-Mcast#sh mls qos interface gigabitEthernet 1/0/22 statistics
GigabitEthernet1/0/22
dscp: incoming
0 - 4 : 0 0 0 0 0
5 - 9 : 0 0 0 0 0
10 - 14 : 0 0 0 0 0
15 - 19 : 0 0 0 0 0
20 - 24 : 0 0 0 0 0
25 - 29 : 0 0 0 0 0
30 - 34 : 0 0 0 0 0
35 - 39 : 0 0 0 0 0
40 - 44 : 0 0 0 0 0
45 - 49 : 0 0 0 0 0
50 - 54 : 0 0 0 0 0
55 - 59 : 0 0 0 0 0
60 - 64 : 0 0 0 0
dscp: outgoing
0 - 4 : 8881981 0 0 0 0
5 - 9 : 0 0 0 0 0
10 - 14 : 0 0 0 0 0
15 - 19 : 0 0 0 0 0
20 - 24 : 0 0 0 0 0
25 - 29 : 0 0 0 0 0
30 - 34 : 0 0 0 0 0
35 - 39 : 0 0 0 0 0
40 - 44 : 0 0 0 0 0
45 - 49 : 0 0 0 307 0
50 - 54 : 0 0 0 0 0
55 - 59 : 0 0 0 0 0
60 - 64 : 0 0 0 0
cos: incoming
0 - 4 : 0 0 0 0 0
5 - 7 : 0 0 0
cos: outgoing
0 - 4 : 8881981 0 0 0 0
5 - 7 : 0 307 0
Policer: Inprofile: 0 OutofProfile: 0
cisco-Mcast#sh mls qos interface gigabitEthernet 1/0/23 statistics
GigabitEthernet1/0/23
dscp: incoming
0 - 4 : 8931330 0 0 0 0
5 - 9 : 0 0 0 0 0
10 - 14 : 0 0 0 0 0
15 - 19 : 0 0 0 0 0
20 - 24 : 0 0 0 0 0
25 - 29 : 0 0 0 0 0
30 - 34 : 0 0 0 0 0
35 - 39 : 0 0 0 0 0
40 - 44 : 0 0 0 0 0
45 - 49 : 0 0 0 202 0
50 - 54 : 0 0 0 0 0
55 - 59 : 0 0 0 0 0
60 - 64 : 0 0 0 0
dscp: outgoing
0 - 4 : 0 0 0 0 0
5 - 9 : 0 0 0 0 0
10 - 14 : 0 0 0 0 0
15 - 19 : 0 0 0 0 0
20 - 24 : 0 0 0 0 0
25 - 29 : 0 0 0 0 0
30 - 34 : 0 0 0 0 0
35 - 39 : 0 0 0 0 0
40 - 44 : 0 0 0 0 0
45 - 49 : 0 0 0 1206 0
50 - 54 : 0 0 0 0 0
55 - 59 : 0 0 0 0 0
60 - 64 : 0 0 0 0
cos: incoming
0 - 4 : 11357772 0 0 0 0
5 - 7 : 0 2 0
cos: outgoing
0 - 4 : 0 0 0 0 0
5 - 7 : 0 1206 2
Policer: Inprofile: 0 OutofProfile: 0
cisco-Mcast#
mls qos disabled:
cisco-Mcast#sh mls qos interface gigabitEthernet 1/0/22 statistics
GigabitEthernet1/0/22
dscp: incoming
0 - 4 : 0 0 0 0 0
5 - 9 : 0 0 0 0 0
10 - 14 : 0 0 0 0 0
15 - 19 : 0 0 0 0 0
20 - 24 : 0 0 0 0 0
25 - 29 : 0 0 0 0 0
30 - 34 : 0 0 0 0 0
35 - 39 : 0 0 0 0 0
40 - 44 : 0 0 0 0 0
45 - 49 : 0 0 0 0 0
50 - 54 : 0 0 0 0 0
55 - 59 : 0 0 0 0 0
60 - 64 : 0 0 0 0
dscp: outgoing
0 - 4 : 0 0 0 0 0
5 - 9 : 0 0 0 0 0
10 - 14 : 0 0 0 0 0
15 - 19 : 0 0 0 0 0
20 - 24 : 0 0 0 0 0
25 - 29 : 0 0 0 0 0
30 - 34 : 0 0 7371 0 0
35 - 39 : 0 0 0 0 0
40 - 44 : 0 0 0 0 0
45 - 49 : 0 0 0 0 0
50 - 54 : 0 0 0 0 0
55 - 59 : 0 0 0 0 0
60 - 64 : 0 0 0 0
cos: incoming
0 - 4 : 0 0 0 0 0
5 - 7 : 0 0 0
cos: outgoing
0 - 4 : 7371 0 0 0 0
5 - 7 : 0 0 0
Policer: Inprofile: 0 OutofProfile: 0
cisco-Mcast#sh mls qos interface gigabitEthernet 1/0/23 statistics
GigabitEthernet1/0/23
dscp: incoming
0 - 4 : 0 0 0 0 0
5 - 9 : 0 0 0 0 0
10 - 14 : 0 0 0 0 0
15 - 19 : 0 0 0 0 0
20 - 24 : 0 0 0 0 0
25 - 29 : 0 0 0 0 0
30 - 34 : 0 0 23281 0 0
35 - 39 : 0 0 0 0 0
40 - 44 : 0 0 0 0 0
45 - 49 : 0 0 0 0 0
50 - 54 : 0 0 0 0 0
55 - 59 : 0 0 0 0 0
60 - 64 : 0 0 0 0
dscp: outgoing
0 - 4 : 0 0 0 0 0
5 - 9 : 0 0 0 0 0
10 - 14 : 0 0 0 0 0
15 - 19 : 0 0 0 0 0
20 - 24 : 0 0 0 0 0
25 - 29 : 0 0 0 0 0
30 - 34 : 0 0 0 0 0
35 - 39 : 0 0 0 0 0
40 - 44 : 0 0 0 0 0
45 - 49 : 0 0 0 2 0
50 - 54 : 0 0 0 0 0
55 - 59 : 0 0 0 0 0
60 - 64 : 0 0 0 0
cos: incoming
0 - 4 : 29272 0 0 0 0
5 - 7 : 0 0 0
cos: outgoing
0 - 4 : 0 0 0 0 0
5 - 7 : 0 2 0
Policer: Inprofile: 0 OutofProfile: 0
cisco-Mcast#
BR Niklas -
I'm trying to configure the router's QoS but I'm not succeeding . I put the game League of Legends as a high priority , but as soon as I turn on the TV with Net Flix the game connection is bad . My questions are as follows - DHCP is not done by the router , but the modem. This would prevent the operation of the QoS ? - QoS just work for WAN connection? Because i'm doing the connection on the ethernet port. - I need to put the TV or the Net Flix as low priority in QoS ? Below modem settings
Thanks for the quick return.Allow me to elaborate : - My internet is 10mb / s- The Internet comes via cable modem / router Thomson. This router is doing DHCP and sharing the internet via ethernet port to the E900 router.- I tried some settings to share the Internet via WAN without success . Thomson Modem configurations E900 Modem Thomson
-
Z77A-GD65 Problems with Ethernet (Intel 82579V) Code 10
Hi,
on a fresh install of Windows 7 64bit i cannot make the Ethernet port on the motherboard work. It installs fine, but when i check device manager i see this message:
This device cannot start. (Code 10)
I downloaded the latest driver, but still no change.
Looking in device manager, i noticed that the driver Windows had selected was Intel 82579LM, so i reinstalled the driver, and forced 82579V driver, but still no change. I assumed this must be a defect motherboard, so i rma'd it, and got a new one....with the same problem!!!
So any ideas with to do ?Quote from: Warner on 11-May-12, 04:10:22
Hello kaizerman,
Are you in the US?
Can you send the motherboard to me directly for analysis?
If needed, I will replace the board for you through RMA service.
Please email me at [email protected] but be sure to put my name in the subject field and your board model so it will come to me correctly.
Sincerely,
Warner
Hi Warner
Thanks for the reply. Unfortunately i'm not not in the US, i'm in In South Africa. Ive tried pro17 with no success... currently its showing the 82579V driver. but no still has the cannot start error code 10. I cant understand why it was working for a few days. then suddenly stopped. i made no hardware or software changes.
regards
Utterly perturbed -
Hi everyone,
I've got a probleme. I red the cisco QoS book, but it doesn't work for me.
I want to do what so many others do, reserve bandwitdh for some specific trafic. But if I test the config, every flow gets the same bandwidth.
I transmit from 2 pc's with a matching ip and a not matching ip each 100MB file. Teracopy shows me the bandwitdh of each 1,3 MB/s and if I look to the folder, the files arrive nearly at the same time.
IOS (tm) C2600 Software (C2600-I-M), Version 12.2(19), RELEASE SOFTWARE (fc3)
Standard IP access list it-intern
permit x.x.x.x (125133 matches)
permit x.x.x.x (60651 matches)
permit x.x.x.x, wildcard bits 0.0.0.255 (905968 matches)
Class Map match-any class-default (id 0)
Match any
Class Map match-any not-it-intern (id 1)
Match not access-group name it-intern
Policy Map cbwfq
Class not-it-intern
Bandwidth 70 (%) Max Threshold 64 (packets)
interface FastEthernet0/1
description # 20 MBit #
bandwidth 20000
ip address x.x.x.x x.x.x.x
service-policy output cbwfq
ip route-cache flow
no ip mroute-cache
duplex auto
speed auto
If I make:
ciscoHV3#sh pol int
FastEthernet0/1
Service-policy output: cbwfq
Class-map: not-it-intern (match-any)
11127978 packets, 4292340182 bytes
5 minute offered rate 4422000 bps, drop rate 0 bps
Match: not access-group name it-intern
11127962 packets, 4292327891 bytes
5 minute rate 4422000 bps
Queueing
Output Queue: Conversation 265
Bandwidth 70 (%) Max Threshold 64 (packets)
(pkts matched/bytes matched) 111155/27836979
(depth/total drops/no-buffer drops) 0/0/0
Class-map: class-default (match-any)
827815 packets, 919625061 bytes
5 minute offered rate 2911000 bps, drop rate 0 bps
Match: any
- I can see that pakets became matched.
I fall in dispair, please help.I've got a WAN connection, which is connected via FastEthernet to the router. The ISP garantees 20 mbit/s. There are 2 IPs and 1 Subnet that got low prior. So I created a Class that "Not" matches that Accessgroup. The remaining traffic should become a minimum of 70% of the bandwidth.
If I understand you, I only get congestion if i would use the physical interface speed (100mbit/s) and only in this case I can use the bandwidth comands.
But would work a config like this?:
Policy-Map cbwfq
Class not-it-intern
Bandwidth percent 70
Policy-Map police-all
Class class-default
police cir 20000000
service-policy cbwfq
interface FastEthernet0/1
description # 20 MBit #
bandwidth 20000
ip address x.x.x.x x.x.x.x
service-policy output police-all
ip route-cache flow
no ip mroute-cache
duplex auto
speed auto
I don't want to use shaping, thats the currently way how I limit the traffic for the sources of the ACL(it-intern). But shaping stresses the router a little bit too much and how I said, I dont want to limit I want to garantee a minimum of traffic.
By the way, thanks a lot for your help until now.
Maybe you are looking for
-
Trying to access powerpc hdd on my macbook pro i5.
Hi folks, I was wondering if anyone knew if it was possible to run an hdd with leopard installed from an old macbook i no longer have which had power pc architecture on a new macbook pro with an i5 processor? I tried a straight disk switch but the co
-
How to continue working on a project if I export the materials?
Hi, I am making a web series and came accross a problem. My computer's hard drive is almost full. I am trying to cut the raw footages and the finished copy of an episode to an external hard drive. I can paste the raw footages and the finished copy of
-
Hi, I'd like to know if it's possible to deploy an application developed with ADF & UIX on a JBoss/Tomcat Server. And what happens with other AppServers? Are there any licensing issues? Thanks. Miquel.
-
Substitution variables deletion
Hi , Some Substitution variables have been deleted in our prod env ..............where/which log files can we find the information ..who deleted them?
-
WebService SOAP response problems
hey, I'm developing a WebService, using EJB's. I have a session bean, which has several methods. One of them returns, say, a class like follows: class TeamDTO implements Serializable { private String name; private Integer teamId; //getters and setter