Qosmio F50-10z' s front operation panel doesn't work

My front operation panel doesn't work. I have tried to recovery my computer and reinstall the VAP but it still doesnt work.
I want to why...

Hi!
What do you mean with if it doesnt work?
If you try to install a newer version of Toshiba Value Added Package you should remove the old version first. Reboot the notebook and install the newer one.
Last but not least try to update the BIOS. You can find it on the Toshiba website:
http://eu.computers.toshiba-europe.com => Support & Downloads => Download Drivers
Bye

Similar Messages

  • Toshiba Front Operation Panel/Illumination Keys not working

    I am unable to toggle wireless on/off, mute/unmute, play/pause using Front operation panel LED keys on my Toshiba Qosmio F60. Currently I need to enable WiFi/Bluetooth from within Windows for it to work. Fn+F8 toggle works as soft block/unblock only if I have already enabled WiFi under Windows. Any ideas as how this can be done? The only LED Touch button that works under Debian/Ubuntu/Fedora is the Volume Up/Down button. Touchpad on/off toggle does not work with physical button above the touchpad or Fn+F9 either. Other Fn+ keys work eg., Fn+Esc for mute/unmute, Fn+F1 for lock etc.
    Interestingly even when the WiFi is turned off from within Windows on booting Arch with a pen-drive wifi-menu command detects all surrounding wireless networks properly for the first time. Even rfkill shows as hardware unblocked. But once a network is selected it fails and the subsequent rfkill commands show as hardware blocked.
    These problems seems related to Direct App Launch Button which probably can be solved in Linux by quickstart http://quickstart.sourceforge.net/
    I had raised a thread in Ubuntu, Debian, Red Hat forums as well
    http://ubuntuforums.org/showthread.php?t=2150307
    http://forums.debian.net/viewtopic.php?f=5&t=108921
    https://bugzilla.redhat.com/show_bug.cgi?id=1074504
    https://bugzilla.kernel.org/show_bug.cgi?id=72711
    The buttons look like this http://www.manualslib.com/manual/180150 … 159#manual
    Last edited by solomonsunder (2014-04-21 11:26:16)

    I get the below output when I run showkey -k
    Fn+1 (Zoom In)
    keycode 419 press
    keycode 419 release
    Fn+2 (Zoom out)
    keycode 418 press
    keycode 418 release
    Fn+Space (Zoom)
    keycode 420 press
    keycode 420 release
    Fn+F8 (Wireless Toggle)
    keycode 238 press
    keycode 238 release
    Fn+F9 (Touchpad Toggle)
    keycode 530 press
    keycode 530 press
    These are soft keys mentioned here http://www.manualslib.com/manual/180150 … 134#manual
    The front panel buttons and the small physical touchpad toggle button above the touchpad do not generate any codes. The Fn+F8 is a multi toggle in Windows after wireless is turned on through the front panel button (first press WiFi on, second press Bluetooth on, third press both WiFI, Bluetooth on, fourth press both off). Also there is no ouput for scancodes when I run showkey -s or xev. Am I missing anything?
    Last edited by solomonsunder (2014-04-22 13:22:22)

  • Qosmio F50-10Z Bios update crashed - how do I reset cmos?

    I have a Qosmio F50-10Z and as prompted by toshiba I downloaded the Bios update and began to install.
    My screensaver came on and the whole thing crashed.
    Would not turn off (even after holding down power button for 15 secs).
    Took battery out and then put it back in. Computer powers on but screen is blank and won't boot up.
    Tried to take it apart to flash the bios by taking out rtc/cmos battery (whatever it's called) but can't find the battery and got to the point where I wasn't willing to take it apart any further (has no-one else ever taken one apart?
    Couldn't find information or diagram or photo of where the battery was on net...manual for laptop really unhelpful)
    Have found comments about crisis disks but I don't know what this means.
    So, how to I reset bios?
    Please help - you are my only hope.

    Thanks for your comments. Do you know where I can download a Bios flasher or Bios recovery crisis disk from? There seem to be a lot floating around forums but I cannot find anything specifically for my laptop. Am I missing something on the Toshiba website? I have seen people mention downloading a bios flash utility from toshiba (specifically for the F45) but can't figure out where they are getting this from...
    In response to your recommendation - I know that is what I am encouraged to do but I'm in the UK - my nearest Toshiba recommended technicians are PC world conglomerate - the sort of guys who pat me on the head when I ask for specific RAM (rather than 'some memory, please'), look blankly at you when you say the word Bios, and bang their mouse when the computer freezes! Besides, they want 50 up front whether or not they manage to fix it, and given how many of my friends computers they have failed to fix that my boyfriend then fixed in ten minutes, I might as well burn my money as send it to them.

  • Booting from ESATA drive on Qosmio F50-10Z

    Hi,
    is it possible to boot from an external drive using the ESATA port?
    I have BIOS 1.60 installed but I don't see an option for ESATA?
    What about a USB drive? Laptop is a Qosmio F50-10Z
    Thanks

    I think its not possible to boot from eSATA. The BIOS must provide such functionality.
    I never tried this but I think this is not possible.
    As far as I know it must be possible to boot from an USB device.
    The BIOS does support this so try it.

  • I just reinstalled PSE 9 and now my edit effects panel doesn't work when I click on it. Help!

    If anybody had this problem and has the solution, please share and I'll be a happy camper again. I have Window Vista. Thanks.

    Hi,
    When you are saying that the edit effect panel doesn't work, Do you mean there is nothing in the panel (It is an empty panel) or there are items but when clicked nothing is happening ?
    Also, Is it the case with Edit Effect panel only or other panels are also behaving in same way ?

  • Qosmio F50-108 - Front operation panel issue

    Hello, I have qosmio F50-108 and the front panel does not work me, I think I uninstal a program. Please link to the driver. thanks akem
    sorry for my bad english

    Hi Akem
    Sorry but I dont understand what you are meaning exactly by front panel?
    Do you mean the Toshiba Control buttons like (play, pause stop, etc)
    If you are meaning these buttons and if you have removed an drivers which controls these buttons then a solution should be easy.
    First of al you should try to set the OS back to the early time point before you have removed this driver. For this you have to use the system restore utility.
    Secondly if the procedure described above will not work, try to reinstall the VAP (Value Added Package).

  • Qosmio F50-10Z - After BIOS update illuminated buttons don't work

    Tempro alerted me about a BIOS update - bios-20090415092322.zip - for 32bit Vista, released 15 April 2009, for my F50-10Z.
    Since then, the illuminated 'buttons' atop my keyboard no longer work - including, annoyingly, the button to turn off the illumination.
    Is there anything I can do at this point? I tried a system restore, but it didn't affect the BIOS.

    Hi, and thanks for your reply.
    I had previously tried reinstalling the Value Added Pack, to no avail (in fact I lost my special function keys also, which I got back via system restore), but after a bios reset it did the job.
    For anybody reading this after the event, to restore BIOS to defaults on a Qosmio f50,
    restart
    hit f2
    hit f9 (then indicate yes)
    hit f10 (indicate yes)
    I don't poke around in BIOS myself, having a healthy fear of the unknown, but I guess something had gone askew somewhere.
    I also found a little program called dimmer.exe which can actually turn off the lights if they are stuck on. For the record, I had the lights switched off when I reset the BIOS and reinstalled VAP
    Thank you both for your assistance.
    Message was edited by: Gemb

  • Card Reader issue on Qosmio F50-10Z

    I have had this issue for a while, It began with the original os Vista 32 bit, so i decided to buy the toshiba upgrade cd for windows 7, after upgrading everything worked fine, except the card reader, no matter how many times i installed/uninstalled,installed the driver it would not work!.
    So I used the recovery cd, not once BUT TWICE, and to no avail i sent it off to repair.
    I got a message on a piece of paper telling me it would work on the original os, i thought they had fixed something.
    So i used the recovery cd yet AGAIN, and to my short lifted excitement of seeing no yellow explanation marks i put in a micro sd card (2gb) which initially worked when i first bought this laptop, and got no response.
    The bigger problem is my warranty is now finished!, So basicly i have been BUMPED OVER, cause the memory card slot is NOT WORKING, and it wasnt an software related problem!
    Any reccomendations?.

    Hi karimtarek,
    Which driver version you are using on Vista and Windows 7? My Qosmio F50 is running Windows 7 and Im using driver version 1.00.29.02 from the Toshiba page.
    Are you using the same version?
    Furthermore it would be interesting to know if the SD card slot worked after you got the notebook from service center back. Have you tested this before or have you started recovery installation immediately?
    Have you tried different brand of SD cards? I always use SanDisk Extreme cards because they never made any problems.
    Furthermore you could try updating the BIOS. Maybe it works if you using a pretty old version
    Last but not least if its still not work and you think its a hardware malfunction, ask the service centre again. If you speak a little bit with technicians, maybe they can repair it as a gesture of goodwill.
    Good luck! :)

  • Remote panel doesn't work

    I am using 2011 SP1 version of LabVIEW, toolkits and add-ons. I am trying to make the following remote panel opening VI work.
    This used to work well on LabVIEW 8.5 but now I get an Error 7 from the last Invoke Node of the second loop. The top loop works fine. HPAC Main.vi is running as a startup VI on the RT target (PXI-8106). I can open its front panel using this VI. But the second loop can't open ST_viewer 1.vi. File names and paths are all correct. For building HPAC.rtexe, on the Source Files tab, HPAC Main.vi was chosen as a startup VI while ST_viewer 1.vi was put in the Always Included box. The VI server of the PXI is using TCP/IP port 3363. The PXI is directly connected to this host PC by an Ethernet cable.
    I also made a very simple project (attached file named ServerTest), deployed its rtext to the PXI and ran it as startup. After rebooting, I tried to open the remote front panel of main.vi and sub.vi on the PXI using access.vi. I get the following errors at the Invoke Nodes.
    For trying to open main.vi > Error 1352: Requested VI is not loaded into memory on the Server Computer
    Fro trying to open sub.vi > Error 7: File not found......
    As suggested in the article, Real-Time System Manager seems useful but I can't find it. Tools > Real-Time Module > and then I can't find the system manager. I only see Project Wizard, Configure Time-triggered Network and Execution Trace Toolkit. Does 2011 version have something else?
    Any help will be appreciated!
    Attachments:
    HPAC Executable.vi ‏33 KB
    ServerTest.zip ‏215 KB

    Thank you, JaymeW. I found the VI States tab in the Distributed System Manager. And yes, all the steps in that article were already done.
    If I set sub.vi as a startup VI on the PXI along with main.vi, then I can open it using the same method that opens main.vi. However, if I put sub.vi in Always Included box on Source Files tab and use the VI server to open it, I get errors.
    On the VI States monitor, I see main.vi running as a startup VI on top level when I turn on the PXI. Then, I run access.vi and open main.vi successfully. When I click the sub.vi open button, sub.vi appears on the monitor with Run Top Level status but I get error messages.
    At the first attempt to call the remote front panel of sub.vi, I get:
    LabVIEW: Resource not found.
    An error occurred loading VI 'lvfpp0.vi'.
    LabVIEW load error code 3: Could not load front panel.
    From the second call, I get:
    Error 1000 occured at Invoke Node in access.vi
    Possible reason(s):
    LabVIEW: The VI is not in a state compatible with this operation.
    Method Name: Run VI.
    Could you take a look at the attached simple project and suggest a solution? Thank you!
    Attachments:
    ServerTest2.zip ‏218 KB

  • If my front screen camera doesn't work

    My iPod is a 5th generation &' it's cracked in the front &' I've tried doing everything but it's doesn't work should getting a new screen help ? Or should I just get it fully repaired ? &' if I do get it repaired how should I get all my stuff back ?

    Apple will exchange your iPod for a refurbished one for $99 for the 16 GB 5G and $149 for the other 5Gs. They do not fix yours.
    Apple - iPod Repair price                       
    A third-party place like the following maybe less. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
    Replace the screen yourself if you are up to it
    iPod Touch Repair – iFixit                  

  • [SOLVED] Front audio panel still not working on K9N Neo V3

    I already posted on this here: https://forum-en.msi.com/index.php?topic=113813.0.
    I still didn't get front audio panel to work on MSI K9N Neo V3.
    Even with my new case; Sharkoon Revenge, it is not working. It wasn't working on my previous noname case too. However, front audio panel on my previous case was working on several other MBs except on this MSI K9N.
    Now, I'm using the latest Realtek HD audio driver.  I think it's from February '08. Just as with the driver dowloaded by Vista via Windows Update, anything plugged in front audio panel isn't recognized. In this new version of Realtek driver I can't find this Disable front audio panel option so I can't tell if it is checked or not.
    Once more, there is not much to do wrong while connecting. Case front audio panel cabel is the same as on all other cases I've ever seen/had. It's a cable with the same number and position of pins as in all other cases. It fits fine on MSI K9N Neo V3. Rear audio panel is working fine.
    Any solution to this!?

    Quote from: Jack the Newbie on 07-April-08, 03:25:15
    From what I can see from the Sharkoon product page, the front panel connectors of your case are not compliant with the Intel HD Audio Pin Standard. 
    Do you have a manual for your case that includes Pin/wire definitions for the front audio connectors?
    No. There was no manual in package. I never thought I will need one either.
    Here is Sharkoon Rebel Pin Assigment; http://img176.imageshack.us/img176/9729/pinslk2.jpg
    Quote from: Jack the Newbie on 07-April-08, 03:25:15
    Have you tried disabling automatic front panel jack detection in the Realtek HD Audio configuration utility?  If you don't know were to find that option, access the tab labeled "Audio I/O" and click on the tool icon.
    Yes, I tried disabling it. Two tabs (front audio out and front mic) appeared but none of it works.
    Quote from: HenryW on 07-April-08, 03:35:46
    From something I read: You can also physically check the audio cable of the front panel audio solution.  If there is a cable connected to Pin 4, you have an HD Audio module; if there is no cable to Pin 4, you have an AC97 module.
    I don't really understand this. Could you please check this on Pin Assignment scan I uploaded above!?

  • Qosmio F50-10Z - fan cycling on and off even when idle

    My f50 is constantly turning the fan on and off every couple of minutes, even when the machine is idle and has not run any applications.
    SpeedFan shows that the GPU is cycling constantly between 55 and 65 degrees C even when there are no apps running (e.g. just after booting) - the fan kicks in at 65, turns off at 55 and then slowly heats up again. The fan noise is noticeable (I don't think it is going full speed, though), and it is a bit abrupt and annoying to be happening constantly and doesn't seem like normal behavior. Core 1 and 2 on Speedfan are cycling between 40 and 45 C
    Outside temperature is 20 degrees, so the environment is unlikely to be a factor. I've air blasted the fan for dust (as much as you can seeing as the f50 isn't built to be taken apart by a Home User), but even when the fan is running the output doesn't seem noticeably hot.
    I'm am only running toshiba drivers from the website (currently 7.15.11.7590)
    My main concern is that this will negatively impact the life of the fan. Am I being overly picky or is there something I could be doing?
    Thanks for any advice

    Thanks for the reply Lars_3.
    The notebook came with Windows Home Premium pre-installed - I haven't replaced the OS at all, though I have created a recovery disk at the urging of OS when I first booted it.
    The BIOS is up-to-date as I use the Toshiba Tempro service (which again was pre-installed) and occasionally check with the website to make sure I haven't missed anything. I don't like the idea of installing drivers or anything else not released by Toshiba as I've seen people mentioning overheating shutdowns (at much higher temps) from using non-f50 drivers. I regularly keep the base elevated to enhance air circulation, and clean the intakes with compressed air, but it doesn't seem to make much difference.
    Everything else works perfectly (and I'm a happy customer) except for the noise factor of the fan switching on every two minutes during even light use (not even 3d game use, which I assume would utilise the 3d card more and be expected to come with greater fan use).

  • LV8.0 Auto-print front panel doesn't work

    On the front panel in VI Properties/Print Options the 'Automatically print front panel every time VI completes execution' is cleared when you exit the VI Properties dialog and return to it.  Consequently, you can't get the front panel to print by checking this option. 
    Brent

    Bshu,
    You're absolutely right. That functionality is faulty. A work around may be to use the operate>>print at completion function. FYI: if you enable this property, the  VI Properties/Print Options the 'Automatically print front panel every time VI completes execution' turns black. R&D is aware of both of these problems. Thank you for you're very valuable feedback and post to let us know if there's anything else we can help out with.
    Best Regards,
    Chris C
    Applications Engineering
    National Instruments
    Chris Cilino
    National Instruments
    LabVIEW Product Marketing Manager
    Certified LabVIEW Architect

  • I have a perplexing problem, in firefox the iframe in the spry tabbed panel doesn't work any ideas?

    I have made a page with spry tabbed panels, i have embedded an iframe in the content section of the second tab, this works perfectly well with Google, IE, Safari, Opera etc but just doesnt work in Firefox.
    If I make the tab panel containing the iframe the Default tab then it works, i just cant figure out why,
    By the way new to all this so be gentle please
    <div id="main_column">
         <div class="section_w500">
            <h2>North Bali Listings</h2>
            <div id="TabbedPanels1" class="TabbedPanels">
              <ul class="TabbedPanelsTabGroup">
                <li class="TabbedPanelsTab" tabindex="0">About North Bali</li>
                <li class="TabbedPanelsTab" tabindex="0">Land</li>   <<<<< This is the tab where the iframe is embedded in the content panel>>>>>
                <li class="TabbedPanelsTab" tabindex="0">Houses / Villas /Apartments / Rooms</li>
                <li class="TabbedPanelsTab" tabindex="0">Commercial</li>
    </ul>
              <div class="TabbedPanelsContentGroup">
                <div class="TabbedPanelsContent">A property analyst recently said that limited land availability in the southern parts of Bali, especially  in and around the Badung and Denpasar areas, has driven investors northward, in our opinion   at this time it is an ideal opportunity to  acquire property still at very sensible prices in this area, be it for investment or as a place of residence.. <br />
                  <p> <img src="../../../Images/Bali Scenes General/panoramic-views.jpg" alt="views" width="183" height="140" align="left" />Over the last few of years, investors have been targeting the northern area,  principally along the coastline ,  with its variety of pristine black sandy beaches, pebble beaches and rugged coastline, offering a variety of activities; scuba diving, snorkelling,  water sports, fishing, sailing. trekking  gives this area the potential to be world-class tourist destination. Research has shown that  property prices are set to rise above the average due to increased infrastructure development, and the planned opening of a new International Airport in the North shows the Bali Government's commitment to the develop this area as a future tourist destination.<br />
                    <br />
                    The Northern part of Bali  is also an excellent base for exploration further afield, close to the main portal for trips to other parts of Indonesia. <br />
                  Although it is largely undeveloped there is a wide range of properties and land with beach front to panoramic rice paddy views still to be found at good value for money. </p>
                  <table width="100%">
                    <tr>
                      <td align="left" valign="top"><div class="AreasOfBaliHighlight" style="color: #60C; font-weight: bolder;">This is an ideal time to consider your dream property  in this area; be it for investment, development or private use.</div></td>
                    </tr>
                  </table>
                  <p> The main tourist area in the North is arguably <span style="color: #F00">Lovina</span>, with property prices reflecting this especially beach front or with panoramic views so expect to see prices a little bit more expensive in and around this area. However inland prices are still very reasonable.<br />
                    <br />
                    <img src="../../../Images/Bali Scenes General/Traditional-lifestyle.gif" alt="village life" width="188" height="137" hspace="2" align="right" />Other  areas to be found in the North going towards <span style="color: #F00">Gillimanuk</span> the main portal for the ferry to and from Java; include: <span style="color: #F00">Pemuteran</span> popular diving area, <span style="color: #F00">Menjangan</span> <span style="color: #F00">Island</span>, a popular diving and nature reserve;  are also beginning to attract investors, resulting in  prices  rising.<br />
                    The area of the North of Bali travelling East from <span style="color: #F00">Lovina</span> towards the eastern part of Bali is quieter and more rural, with stunning coastline and secluded traditional village life, here life slows down, people are very friendly and happy to integrate with &quot;Bule (Foreigner), this life style is definitely completely different to the hustle and bustle of the South of Bali, perfect for future development and peaceful retirement, and with the development of the new <span style="color: #F00">International Airport</span> in this area, about 1/2 way between <span style="color: #F00">Singaraja</span> and <span style="color: #F00">Almpura</span> in the East, which makes this area an ideal investment opportunity as property and land prices are set to grow in this part of North Bali faster than other areas.<br />
                    <br />
                    <img src="../../../Images/Bali Scenes General/img_bali_1.jpg" alt="Quiet Lanes" width="189" height="124" hspace="2" align="left" />It has to be said that facilities for schooling, medical services and shopping are not as good as in the South or around Ubud area, which have higher concentrations of  established ex pat communities, and better facilities  also the job opportunities are not anywhere near as plentiful as in the South or Ubud areas, which limits the lifestyle for many people looking to settle in Bali, careful consideration has to be given if your intention is for a place for you to reside, and it is possibly an area for consideration as an investment opportunity, or for a development of hotel or villa resort, or as a second retirement home. </p>
                  <p>There are of course facilities for all the usual services and plenty of job opportunities, and a small but growing ex-pat community, especially in and around <span style="color: #F00">Lovina</span> and <span style="color: #F00">Singaraja</span> just not as many as in the other popular areas for ex pat's. </p>
                </div>
                <div class="TabbedPanelsContent">
                  <p> </p>
                  <table width="100%" border="0">
                    <tr>
                      <td valign="top"><h7 style="color: #C03"><span style="font-weight: bold"><span style="font-size: 12px; color: #FFF;">Property Code BSP 00130101</span><span style="font-size: 16px"> </span>SAMBIRENTENG - North East Bali 7,300 meters (</span></h7>
                        <span style="font-weight: bold; color: #B90033;">73 ARE) Beach front flat wooded land for Sale/ Rent</span></td>
                      <td><span class="button_01"><a href="#" onclick="MM_openBrWindow('North Bali/Gold Package Listings/BSP-00130101/Sambirenteng  Property Location Map.html',width=750,height=200')">Location Map</a></span></td>
                    </tr>
                    <tr>
                      <td width="77%" valign="top"><p>A golden opportunity to acquire a prime plot of beach front land in the North East of Bali in an area that enjoys newly awarded &quot;Tourism Status&quot;  ideal for the development of a small hotel or villa complex, easy access to many popular tourist spots already developing in the North.</p>
                        <p> A 3 meter wide sealed road gives acces to the whole length of this prime plot of land: Electric (PLN) Water (PDAM) Telephone &amp; Internet close to hand and readilly available</p></td>
                      <td width="23%"><a href="Carousel Sambirneteng Listings.html target="_parent"></a><iframe src="Carousel Sambirneteng Listings.html" allowtransparency="yes" frameborder="no" height="111" width="156" scrolling="No" align="middle" marginheight="0"></iframe></td>
                    </tr>
                    <tr>
                      <td valign="top">Purchase price<span style="color: #33C; font-weight: bold;"> 12,500,000,000 Rp</span><br />
                        Rental Price (25 years) <span style="font-weight: bold">9,450,000,000</span> <span style="font-weight: bold">Rp</span> <span style="color: #FFF"> (<span style="font-weight: bold; color: #3333D0;"> 5,200,000 Rp</span><span style="color: #3933D5"> </span> per are per year )<br />
                          Min Rental Period 25 Years, extendable to to a max of 75 years
                          (with full &quot;Right Of Use&quot; issued by owner)</span></td>
                      <td valign="top"><p class="button_01"><a href="../Gold Package Listings/BSP-00130101/BSP00130101 Details.html">Find out more</a></p>
                        <br />
                        <span class="button_01"><a href="../Gold Package Listings/BSP-00130101/BSP00130101_Enquiry Form.html" target="_parent">Make Enquiry</a></span></td>
                    </tr>
                  </table>
                  <p><br />
                  </p>
                  <hr width="100%" noshade="noshade" />
                  <p> </p>
                </div>
    <div class="TabbedPanelsContent">Sorry we don't have any listings under this catagory at the moment,,, Check back later or register with us, and we will send you regular updates of any new properties we list.<iframe src="Carousel Sambirneteng Listings.html" allowtransparency="yes" frameborder="no" height="111" width="156" scrolling="No" align="middle" marginheight="0"></iframe></div>
                <div class="TabbedPanelsContent">Sorry we don't have any listings under this catagory at the moment,,, Check back later or register with us, and we will send you regular updates of any new properties we list.</div>
    </div>
            </div>
            <p> </p>
          <p>
            <h7 style="color: #C03"></h7>
          </p>
    <h2></h2><!-- this stays empty to put dotted line under listings block -->
         </div>
         <div class="cleaner"></div>
        </div> <!-- end of main column -->

    Could you share a link to the page?
    Seeing it in context and in our browsers is much easier to debug.
    If not, make sure to run the validator here The W3C Markup Validation Service and clear out any problems. HTML errors, especially structural ones, will cause all kinds of display problems in various browsers/versions/platforms.

  • Hp office jet 7500 won't send fax, control panel doesn't work

    Control panel on HP Officejet 7500a printer/fax does not function, pressing icons is fruitless
    New ink cartridges recently installed
    Using 2 line telephone connection 

    Hi @cam100,
    I am wondering if a reset might help.
    I will send you a PM (Private Message), but before I do, feel free to review the HP Privacy Statement.
    This Privacy Statement informs you of our privacy practices and of the choices you can make about the way information about you and your online activity is collected and how that information is used. This statement is readily available on our HP.com home page and at the bottom of every HP web page.
    There are an increasing number of posts in this forum and elsewhere in the internet with the steps to do a resets on different printers.  The reset itself will sometimes fix problems, so the reset is not the issue. 
    Some resets require you to enter button combinations to open special menus on your printer that you were never meant to access.  These special menus are used by the developers and support personnel for debugging issues, but they are not meant for untrained users and can have unintended results.  One wrong button push and you no could no longer have a printer, but instead a pricey paper weight.  To top it off, if you do happen to "brick" the printer this way, it is considered customer induced damage, and voids the warranty automatically. These resets are only meant to be given out and used as a last resort, and under direct instruction of a HP tech support representative. They should not be done lightly!
    Printer Resets: What You Should Know
    Please check the little envelope on the top right hand corner of the forums page to check your Forums inbox.
    Please click the Thumbs up icon below to thank me for responding.
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Sunshyn2005 - I work on behalf of HP

Maybe you are looking for