Qosmio F750-03W - face recognition not start and video freezes

I apologize for my English.
Nvidia 3D testing program wheel shots. The face recognition does not start.
If on, the image activator 3D is disturbed and I do not see the image in 3D.
If I try the Games 3D compatible (Left4Dead) activates the 3D in 1080p but the game is jerky as the test image 3D not activate the face recognition.
3D play is to see in 2D photos into 3D but how do I vadere photos in 3D?
If active 3D activator the image quality is poor.
I did set both normal and advanced, but the videos have gost effects especially on the sides.

Hi
It looks your Qosmio F750-03W PQF75C-03W001 is an Toshiba Canadian model as I found this here:
http://support.toshiba.ca/support/isg/center/en/index.asp?s1=Notebook&s2=Qosmio&s3=F750&s4=PQF75C-03W001
First of all you should update the BIOS to the latest version (at this time it seems that BIOS 2.0 is the latest one).
Also update the
nVidia Display Driver version 8.17.12.9039
Super-D IC Driver version 1.0.1613.809
Toshiba Blu-ray Disc Player version 1.0.1.299
as mentioned here http://support.toshiba.ca/support/isg/tsb/en/view.asp?docid=TSB001633
if 3D stereo effects are not ok use the X-tune to calibrate this.
You are recommended to use this utility to optimize the 3D stereo effects when using the Glasses-Free 3D function for the first time or being unsatisfied with the 3D effects.
To operate the X-Tune utility, follow the steps as described below:
1. Select the language and optimization mode, and then click OK. There are three optimization modes: Primary, Advanced and Professional. You can choose one based on your own experience.
2. Sitting about 60cm away from your computer, click Start to continue.
3. Follow the on-screen instructions on each step.
4. Use the left or right arrow key on the keyboard to adjust the effect. When you are satisfied with the effect, click Enter and then an information window will appear on the screen. Press the ESC key on the keyboard to cancel the optimization procedure.
5. Click Finish to close the X-Tune utility.
You said your face recognition does not work properly so uninstall this software. Do this also with the webcam driver/software. After both tools has been uninstalled, clean registry using CCleaner and install both tools again using the newest version.
Reboot and start the X-Tune again to calibrate the 3D effects.
In the Toshiba doc (link posted above) you can find this notice:
1. Set [Screen resolution] to 1920x1080. Glasses free 3D mode is not enabled except in 1920x1080 mode.
2. Depending on game, it does not work with glasses free 3D mode and work with 2D mode.
3. Depending on game, it is not displayed correctly with stereoscopic 3D mode
4. Game is not displayed with glasses free 3D mode when running TOSHIBA Blu-ray Disc Player with glasses free 3D mode
or running TOSHIBA Web Camera application.
5. The performance of the game will be decreased when playing game with glasses free 3D mode. If the performance of the game is decreased dramatically, please decrease the quality of image of the game using settings
of the game. If the performance of the game is still not enough, please disable glasses free 3D mode by unchecking [Enable stereoscopic 3D] at NVIDIA Control Panel.
6. Small fonts in the games may be difficult to read with glasses free 3D mode. At that time, please push 3D button of PC and disable glasses free 3D mode temporarily. Glasses free 3D mode is enabled if you push 3D button again
7. The response of the game may delay with glasses free 3D mode enabled. If you feel it and can not enjoy the game, please disable glasses free 3D mode by unchecking [Enable stereoscopic 3D] at NVIDIA Control Panel.
8. Glasses free 3D mode can be disabled temporarily by pressing 3D button of PC but it may be enabled while playing game. At that time, please push 3D button and disable it again.
9. When [Enable stereoscopic 3D] in NVIDIA Control Panel is unchecked, game will start with 2D mode. At this time, glasses free 3D mode is not enabled even if you pressed 3D button of PC while playing the game.
10. Glasses free 3D mode may be enabled except TOSHIBA Blu-ray Disc Player and games. At this time, please disable glasses free 3D mode by unchecking [Enable stereoscopic 3D] at NVIDIA Control Panel.
11. The color of video may be different from original when playing video with full screen mode on RGB and non 3D TV if [Enable stereoscopic 3D] is checked. At this time, please disable glasses free 3D mode by unchecking [Enable stereoscopic 3D] at NVIDIA Control Panel.
Hope this helps.

Similar Messages

  • Audio stopping and starting and video freezes

    Hello, I was playing back a clip in imovie when the audio stopped and started, and the video freezed.
    Please help.
    -filmmayker

    Never mind - I finally got it to stop. Thanks!

  • I am not able to launch FF everytime i tr to open it, it says FF has to submit a crash report, i even tried doing that and the report was submitted too, but stiil FF did not start, and the problem still persists, please help me solve this issue in English

    Question
    I am not able to launch FF everytime i try to open it, it says FF has to submit a crash report,and restore yr tabs. I even tried doing that and the report was submitted too, but still FF did not start, and the problem still persists, please help me solve this issue
    '''(in English)'''

    Hi Danny,
    Per my understanding that you can't get the expect result by using the expression "=Count(Fields!TICKET_STATUS.Value=4) " to count the the TICKET_STATUS which value is 4, the result will returns the count of all the TICKET_STATUS values(206)
    but not 180, right?
    I have tested on my local environment and can reproduce the issue, the issue caused by you are using the count() function in the incorrect way, please modify the expression as below and have a test:
    =COUNT(IIF(Fields!TICKET_STATUS.Value=4 ,1,Nothing))
    or
    =SUM(IIF(Fields!TICKET_STATUS=4,1,0))
    If you still have any problem, please feel free to ask.
    Regards,
    Vicky Liu
    Vicky Liu
    TechNet Community Support

  • Just installed Firefox 3.6. Firefox will not start and Firefox safemode does not start either. Using Task manager I do not see if started either. If I create a new profile and start from that window, Firefox starts up. I see no error windows/messages. I d

    Just installed Firefox 3.6. Firefox will not start and Firefox safemode does not start either. Using Task manager I do not see if started either. If I create a new profile and start from that window, Firefox starts up. I see no error windows/messages. I do have it listed in my Firewall as an exception program with Permit All. What is happening?
    == This happened ==
    Every time Firefox opened
    == After removing Firefox and Reinstalling it. ==
    == User Agent ==
    Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; GTB6.4; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.04506.30; .NET CLR 3.0.04506.648; MS-RTC LM 8)

    If that new profile works then you can transfer some files from the old profile to that new profile (be careful not to copy corrupted files)
    See http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox
    See also [[Basic Troubleshooting|#Make_a_new_profile|Basic Troubleshooting: Make a new profile]]

  • I attempted to load Itunes update and it will not start and faults out

    I attempted to load an update to I Tunes and it has now faluted out and will not start and it gives me an error message

    Hey lljmustang,
    Thanks for the question. I understand you are experiencing issues with iTunes for Windows. Let’s troubleshoot the iTunes installation by completely removing and reinstalling iTunes and all related components (it is important to remove all components in the order listed).
    Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
    http://support.apple.com/kb/HT1923
    Additional Information:
    How to restart the Apple Mobile Device Service (AMDS) on Windows
    http://support.apple.com/kb/TS1567
    Issues installing iTunes or QuickTime for Windows
    http://support.apple.com/kb/HT1926
    Thanks,
    Matt M.

  • TS1702 i have erased my all phone contact list and then the message comes that it will be deleted with in an hour. but now my phone is not starting and only the apple logo appears on the screen. what should i do now..!

    i have erased my all phone contact list and then the message comes that it will be deleted with in an hour. but now my phone is not starting and only the apple logo appears on the screen. what should i do now..!

    That number is for an apple server in the UK that is used for iMessage activation.  A hidden SMS is snet to that number when you turn iMessage on and is used to verify your phone number.  I suggest you turn iMessage off.  In settings/phone turn on dial assist.  Check with your carrier to see if you can send an international SMS as you end that possibility to activate iMessage.  Rest your phone (Hold down the Sleep/Wake button and the home button together until the apple logo appears (ignore the ON/OFF slider) then let both buttons go and wait for device to restart (no data will be lost).) then turn iMessage back on.

  • When i plug my ipod in it says ipod cant be read cuz the apple mobile device is not started.And i went to services and apple mobile device properties and start stops in the middle.and its on automatic.and there isnt a stop button.

    when i plug my ipod in it says ipod cant be read cuz the apple mobile device is not started.And i went to services and apple mobile device properties and start stops in the middle.and its on automatic.and there isnt a stop button.when i click start it says the apple mobile device services stopped in the middle then stopped.it said some services stop in the middle if not used by other services.and i just updated itunes before all a this and ever since ive had errors.

    Have you looked at this article:
    iPhone, iPad, iPod touch: How to restart the Apple Mobile Device Service (AMDS) on Windows

  • Firefox will not start and open a website from a Thunderbird email link. It will go to a link from Thunderbird once Firefox is open, but will not initially start Firefox and proceed to open the Thunderbird email link.

    Firefox will not ''start'' and open a website from a Thunderbird email link. A link from Thunderbird will open once Firefox is ''already'' started, but will not initially start Firefox and proceed to open the Thunderbird email link.

    I also have this problem. I cannot open links from a discussion board I frequent nor can I open links from my email. Also after opening my email, I cannot go to any other sites except my home page. I can then go no where else.
    When I close Firefox and try to reopen it, it does nothing! I have to bring up the Task Manager and end the Firefox process before I can get back in.
    To the best of my knowledge, this problem started with the new update to Ver. 3.6.9. I am running Windows XP Media Center 2005

  • Oracle Fulfillment server does not start and also my concurrent manager is

    The oracle Fulfillment server does not start and also my concurrent manager is down, when ever iam trying to start them i getting error.
    even i restarted my laptop many times
    Iam using WINXP on my laptop.
    Pls help someone
    hsawwan
    Posts: 11,859
    Registered: 03/13/06
    Re: oracle Fulfillment server and concurrent manager problem
    Posted: Oct 13, 2008 9:26 AM in response to: user578071 Reply
    What is the error?
    What does CM log file say?
    Please run cmclean.sql and try to start the CM then.
    Note: 134007.1 - CMCLEAN.SQL - Non Destructive Script to Clean Concurrent Manager Tables
    https://metalink.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=134007.1
    where should i run in apps schema or some other schema, where can i find the log
    as iam using r12

    Duplicate thread ..
    oracle Fulfillment server and concurrent manager problem
    Re: oracle Fulfillment server and concurrent manager problem

  • My Imac does not start and make a terrible noise like an alert.

    Please help me, my Imac does not start and make a terrible noise like an alert when try to start ,the Imac keep a grey screen when try to start and keep there.

    Sounds like it is time  to take it to an Apple Store or AASP to be serviced. You can also try troubleshooting using Apple's Gray screen appears during startup instructions.

  • Apple home start page will not start and games will not load with flash.

    Apple home start page will not start and games will not load with flash.

    Never mind...I just figured it out. Restore windows when quitting box in Gen Prefs must be unchecked. To many new little things.

  • VisualRF not starting and showing communication error timeout

    Problem:
    VisualRf is not starting and shows connection timed out on the Airwave GUI.
    If we look at the visualRF logs,  from the location /var/log/visualrf/visualrf.log
    we can see the below error in the log:
    2015-06-14 11:53:29,461 WARN Inventory com.airwave.amp.RoleParserImpl Existing login cookie is null. Initialize amp login. 
    2015-06-14 11:53:29,479 ERROR Inventory com.airwave.amp.RoleParserImpl Failed to initialize session cookie. 
    2015-06-14 11:53:29,479 ERROR Inventory com.airwave.amp.RoleParserImpl prepareMethod 
    java.lang.Exception: Failed to login.
    Diagnostics:
    When we look at the below error,
    java.lang.Exception: Failed to login.
    We could see that VisualRF is trying to login to Airwave database and failing to login for whatever reason. When we look at the Airwave database for this visualRF user, we could see this below:
    The highlighted username in Yellow is the visualRF, VisaulRF creates this username randomly and we could see that login_attempts for this user is 10 and Airwave disables the user after 10 attempts. Therefore that explains why is_enabled  is 0.
    This could happen for different reasons, when we restore the visualRF backup and backup has some issues or when we do a vrf bootstrap, to do a factory reset on visualRF or could be any other reason.
    Solution
    To resolve this issue, all we need to do is update the Airwave database to enable this user, as shown below:
    [root@localhost mercury]# dbc "update users set is_enabled = 1 where username = 'AihmrH3MHQ';"
    once done, VisualRF would start working normally.

    Got the screenshot, thanks. And hello again Rob
    Follow-up:
    2) Not sure that it matters, but what's the url you see in the BrowserLab UI after making the request? What path do you have defined as the Local Site Path in your site definition in DW?
    3) How are you requesting the screenshots? From the BrowserLab panel inside DW?
    4) Open up the BrowserLab panel in DW and see what the drop-down control is set to. If it doesn't say "Local" change it to Local and press the preview button and let me know what happens.
    6) I want to make sure that none of the assets your page(s) need live outside the directory you've got within your DW site definition.
    Thanks,
    Mark

  • I pad not starting and showing linings..

    My i pad is not starting and showing linings of different colours when sleep/ wake button is pressed, then screen goes off . Again pressing sleep button is showing linings again. Holding home button with sleep button is also not solving the problem. I tunes is not downloaded on my ipad. It has been upgraded to
    i OS6.

    Have you tried a reset ? Press and hold both the sleep and home buttons for about 10 to 15 seconds, after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

  • Garageband does not start and I get this open and do not shut down or restart

    garageband does not start and I get this open and do not shut down or restart

    Such an error is always caused by inconsistent files in the Firefox program folder (application.ini and/or platform.ini and possibly others) and your only option is to reinstall that version of Firefox, either via the software repositories or the Mozilla server.<br />
    Be sure to delete all files in that folder before copying the files from that tar.bz2 archive.<
    *http://kb.mozillazine.org/Installing_Firefox#Linux
    Note that the current ESR version is 10.0.5
    *http://www.mozilla.org/en-US/firefox/organizations/all.html
    *http://www.mozilla.org/en-US/firefox/17.0.5/releasenotes/
    *http://www.mozilla.org/en-US/firefox/17.0.5/system-requirements/
    All Firefox releases:
    *https://ftp.mozilla.org/pub/mozilla.org/firefox/releases/ (17.0.5esr/, latest-esr/, latest/)

  • SAP MMC does not start and red in color

    Hi Gurus,
    We are in a process of installing EhP4 and there were lots of errors. We reverted back to old version.
    After moving back to old state i.e., EhP3, system does not start.
    1. SAPosCol does not start acutomatically in the service
    2. sapmmc does not show database details
    3. When I try to start the server through SAPMMC, all esmart03 0, esmart03 1 turns to red.
    Please let me know how i can fix this problem.
    I want to post screen shot, but i am not sure how i can post the same here.
    Thanks in advance.
    Regards
    Shreeshail

    Thanks Sunny for your reply.
    We had taken system system backup (complete "E" drive) where SAP server is installed. I had to stop EhP4 process as we got a requirement to bringup NWBC.
    We restored the "E" drive content and then restarted the SAP server.
    After that servies did not start and MMC does not show up Database details.
    Do i need to create services and MMC to fix the issues??
    Thanks in advance.
    Regards
    Shreeshail

Maybe you are looking for

  • 27" runs hot in target display mode

    Anyone else notice this..I use my 27" imac in Target Display Mode for my Mac Pro only and for some reason the fans slowly ramp up..especially the cpu unit to at least 1500. I find this odd as no processing is done and I doubt the GPU is used either.

  • Sourcefire - Malware cloud lookup fails with 'cloud lookup timeout'

    Hi, I am performing malware clould lookup using FirePOWER on ASA. I see the file event when I transfer the file, but the FireSIGHT is unable to  submit the file SHA-256 for cloud lookup. It times out. The FireSIGHT management IP is able to access the

  • Attach vi's in defined version

    Hi all As one might know there are different versions of LV in use and not everyone uses the newest version. Often there are attachments in some topics I'd like to look at, but in the end I can not because of the version (I use LV7.0, which is not th

  • Controlling within mini-player clears search field - annoying bug

    I've come across this annoying (repeatable) bug with iTunes 9... when I listen to music, I like to put an artist's name in the search field, then just let it play on shuffle from those search results. Typically no big deal, however, if I switch to th

  • I need to increase the sample rate to 50KHz to allow for arc detection

    In an effort to get our arc detection software running we need to capture data with a sampling rate greater than 10kHz. Would setting the 'samples per cycle' to 512 (as opposed to 192) would allow us to use your re-sampled data at the RT-Controller (