Qosmio G30-126: how to connect analog TV and satellite TV simultaneously

Hi, I have a Qosmio G30-126 and have a problem with simultaneous receiving analog TV (by TV-in port in built-in TV tuner) and satellite channels from satellite set-top-box (by AV-in ports).
I can programm Windows Media Center for analog TV (but without satellite STB) by antenna TV-in port and it works perfectly.
I can programm Windows Media Center for digital channels from satellite STB (but without analog TV) by AV-in ports and it works perfectly.
But i can't program Windows Media Center for both analog TV i satellite STB, because during programming WMC forces me to choose between analog TV or satellite decoder and doesn't allow me to choose two signal sources.
For me it is a big problem, because I have cable TV (analog) and satellite STB with digital channels. And I want to watch on my Qosmio all channels.
Could anyone help me?

>... because during programming WMC forces me to choose between analog TV or satellite decoder and doesn't allow me to choose two signal sources.
I think in this statement you answered your question. I had Qosmio G30 long time ago and i also know that WMC cannot handle with two signal sources at the same time.
To confirm this contact Microsoft and ask them. I mean they have designed WMC and know how it works exactly.
Toshiba has just offered proper hardware (TV tuner) to offer TV option on this notebook.

Similar Messages

Qosmio G30-126 - How to get access to the bios!

I have a laptop Qosmio G30-126 and I don't know the key for entering the bios to change to properties for the HDD or any thing... so how to get access to the bios? what is the key for the bios??

Hi
Try to press the F2 button while powering the unit.
Older Toshiba notebooks supported the ESC and then F1 button
So these two options are possible

Qosmio G30-116: How to connect the Sky Digital box to watch TV?

I just recently purchased the Qosmio G30-116 on the understanding that I can connect my Sky digital to the laptop (somehow) and watch and record sky on the laptop
* note: I am not using freeview or normal TV I am using SKY DIGITAL *
usint the supplied converter cable to connect to the video-in on the laptop (video in is like a headfone jack and the converter converts from this to female RCA)
I have plugged it into the laptop then connect a 3 RCA to SCART to it and then into the sky box, when setting up the TV section in Windows Media Centre I follow the instructions until it gets to the point where it scans for a signal, (previous to that I get asked what kind of signal I receive, I select digital but have tried all combinations,) but it doesn't find a signal.
Now I have been told that Windows Media Centre does not support Analogue input and that the connection between the sky box and the laptop is analogue.
Is this correct or not? then, while typing this I have been told by someone else that my laptop is not capable of receiveing SKY DIGITAl as it can't decode it or something. Is this also correct? If not, what am I doing wrong and can anyone help me get this going? And have I been going about this the right way or am I totally up the wrong path if laptop is capable of it?

To start qosmio player
1.switch off computer using on/off blue lit on/off button to close windows operation.
2.make sure that the computer/windows is switch off
3.Now Touch the TV icon (Blue lit button)only or the DVD player ICOn (blue lit button)only. WITHOUT USING THE USUAL ON/OFF SWITCH
4.The qosmio player/engine will switch on instantly without booting windows.
5.TV will launch within 8 seconds and the same for DVD player
6.Pres F1 or F2 for further functions such as screen size,audio,forward.rewind.pause scanning the TV channnels (auto or manual)
7.You can do the same i.e open the qosmio player/TV with the supplied Toshiba/qosmio remote pressing the Live TV button ONLY for instant TV on or DVD menu ONLY for instant DVD player/CD player on WITHOUT USING THE ON/OFF SWITCH ON THE REMOTE.That is very much similar to a standard TV remote just press the TV or dvd menu .
8.If you touch the same icon buttons i.e TV and dvd player during the standard computer usage /windows operating system,IT WILL LAUNCH THE MEDIA CENTER BY DEFAULT.that's what happen to you!
I use the remote from my bed before going to sleep and the same from bed to watch early morning TV news
Qosmio is excellent for the versatility!
Enjoy
min
Message was edited by: min
Message was edited by: min

Qosmio G30-126 - Strange scratching noise

Hi!
I have a Qosmio G30-126 and OS Vista Ultimate. about a month ago my laptop was taken to service because it wouldn't turn on, but since last week, when I started it up there was a prolonged scratching noise on the startup, and since then whenever Im listening to music or if the laptop's on standby, there are some very weird scratching sounds coming out from the speakers. Short sounds that keep being repeated. Sometimes they stop after a few times, and other times, like last night, I had to restart.
I tried updating all available drives, but everything seemed up-to-date. I also googled the issue, but none of what I found was relative.
Can someone give me a clue as to what the issue might be? Is there something I haven't thought of that needs to be done?
Thanks a lot in advance!

That might be an option...how can i see if it is the fan though? Is there a way to do it on my own?
Is it possible that these sound issues might be because of overusage? I don't keep my laptop on 24 hrs a day, but some days it's on till the evening. But only after the service did this whole thing occur..

Qosmio G30-126 monitor become black and FN buttons don't work

Hello,
I have small problem, ehm two problems but perhaps small for you :)
Last week I install Vista ultimate WITHOUT RECOVERY CD..
It's OK, but I'm closing cover of notebook and instantly open, monitor become black and i can't anything do beyond restart .
In Control panel in possibilities of power supply , bookmark "options for closing pad" doesn't work.
Maybe it is by, because i don't driver if exist
And second problem maybe related with first but this is mistake by it, because I wasn't discover drivers because i don't hidden toolbar on up on dispay in Windows, where is standartly is.
I don't work major part hidden functions under key FN ( I think FN + F2,F3...F12) plus keys be the side POWER without multimedia keys on music..
Thx for help !!!
Sry for my bad english
Message was edited by: Martiosso

Hi Martin
First of all its interesting if you have downloaded and installed all Toshiba Vista drivers which are released on the Toshiba European driver page?
All drivers must be installed in the right order!
If I'm not mistaken the Qosmio G30-126 belongs to the PQG32E series. It was delivered with HD DVD drive and therefore you should choose the drivers for Qosmio G30 HD DVD (PQG32E)!!!
Please check firstly the Installation Instructions txt file and then install all drivers like mentioned in this document.
Regarding the display issue;
You should install the right NVIDIA driver from the Toshiba page!!
The FN keys and control buttons dont work because the Toshiba Vista Value Added Package was not installed. This package contains different applications which are necessary to get all Toshiba functions running!
Good luck

Qosmio G30-126 - Win7 or Vista instaltion hdd not showing

Hello everyone,
i have one system Qosmio g30-126.
I dont have the recovery cds.
I want to instal the Win7 or Win Vista.
He is not showing me the both 200+200 HDD.
plz telling to me what i do.

Hi mate
I think you dont need a SATA driver but RAID driver!
As far as I know the Qosmio G30 supports RAID and therefore you need to include the RAID driver.
Visit the Toshiba European driver page and download the RAID driver which is listed in the list.
Note: Choose the Archive in Product Type because G30 is an older series.
After you have downloaded and uzipped the driver, you will have to add this driver during the Windows installation setup.

How to connect my iPhone and iPad to Apple TV

How to connect my iPhone and iPad to Apple TV

Connect the iPad and Apple TV to the same WiFi network. Double Tab the home button on the iPad and then swipe your recently used apps from left to right until you see the mirroring icon which looks like a retangle with an up arrow. Tab that icon until you see the Apple TV. Tab Apple TV and slide the slider to the ON position. You should now see your iPad screen on the TV the Apple TV is connected to.

How to connect my iPad and iPhone to my new apple tv ?

how to connect my iPad and iPhone to my new apple tv ?

Also, make sure that all devices are on the same Wi-Fi network (e.g. not on a "guest" connection), and verify the ATV settings to see that AirPlay (and HomeSharing while you're at it) are turned on.

How to connect Master socket and extension to fibr...

I have just had my fttp service enabled.
I watched the online video on how to connect my phone, and it says that if you don't have the special socket that allows you to switch from copper to fibre, you should just connect the phne to the modem.
I don't have the socket, just a normal phone socket right next to the modem.
How do I connect my extensions? Can I just connect my modem to the socket and go from there, or do I need to do anything else?
Sorry folks, I know very little about this stuff!

There is a guide here.
http://bt.custhelp.com/app/answers/detail/a_id/37138/related/1
My guess is that you would have to disconnect your extension wiring from the old master socket, and plug it into the Tel 1 socket via a phone splitter, if you need a phone near the fibre modem.
There are a few other FTTP users on this forum, who may be able to give you more advice.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

How to connect Template project and Implementation project

Hi Experts,
     I would like to know how to connect Template project and Implementation project
    in Solution maneger.   Please help.
Best regards,
   Gaito

Hey Gaito,
great. Now that you have a template project, you need to create one or more templates within the project template.
Go to tab Templates (of your Templ Proj) and activate 'Global Rollout Functionnality' to be able to use the templates.
Create a new template thanks to button create. Visibility will be set to red 'private'. You ll have to set it to visible so it becomes visible from your implementation project.
You ll see when trying to do that next message 'No scenarios/configuration structures assigned to the template XXXX'. That means that in SOLAR01 you did not define a scenario that ll be used in template you re trying to create
In order to do that go to SOLAR01 for template project, select/create scenarios in tab structure and set in column template value of your template (the one you re creating in SOLAR_PROJECT_ADMIN) and in Global Attribute set value t Global
You l definitely find more info on this in sap document SMI310 (course). I don t know if you can find it on internet
Hope this helps
Regards
Khalil

How to connect, add delete and modify sqllite data base.

dear friends,
i am developing a stand alone project, in that i want to
store the datas in the local machine using sql lite. Iam new to
Flex. i know air and flash very well.. any body can help me, how to
connect, add, delete and modify the data in sql lite. i want to
store users option in local machine.. i got struct up. i have to
finish my project...pls..
thanks and Regards,
Syed Abdul Rahim

Hi,
Please find details on how to access SQL Lite database from
AIR applications at the URL below.
http://livedocs.adobe.com/flex/3/html/SQL_01.html
Hope this helps.

Qosmio G30-161: How to set dual screen in Vista

Hello, I have tried loads but am getting no where, I can get the other screen to work by shutting down and booting up but I only ever get one screen to work is there simple step by steb guides to getting dual screen working my machine is a G30-161 running Vista Ultimate.
Many thanks
Michael

I have had the same problem. I have a Qosmio G25-av513 which came with XP. I upgraded my operating system to Vista Ultimate and have everything working fine but have lost the ability to use the FN-F5 to activate a second display. After reading this user's similar problem, I tried turning my laptop off, connecting my projector and turning my laptop on again.
The projector now works but the laptop screen will not turn on until I disconnect the projector and reboot.
Anyway, I can live with that!

Qosmio G30-162 - How to handle dead battery?

I only use my Qosmio G30 connected to the mains. The battery is now exhausted and thus I have lost use of the computer. Do I have to replace the battery or is there any method of converting the PC for mains-only use? Any advice appreciated.. Elderly user.

Hi,
No, in such case you cant repair the battery and you need a replacement battery because battery is not repairable.
>or is there any method of converting the PC for mains-only use?
Hmm I dont know what you mean but you dont need a battery. You can also use the notebook with AC/DC adapter only. Thats no problem. :)

How to synchronize analog input and output from two different USB daq boards

Hi all,
I have two very differnt USB boards the NI USB 6008, which I am using to acquire the data (Analog Input) and a NI USB 9263, it is an Analog Output only board that I am using to deliver a signal (in this case a square pulse). The reason why I am not using the 6008 Analog Ouputs is because I need to deliver negative voltages and need the full +/-10V range.
Looking at similar posts I am pretty sure that I can't use an external trigger or a shared clock, I also tried to use the synchronization of timed structures but no cigar.
I am including a quick vi that I whipped out showing how the signal jitters due to the lack of synchronization. The AO from the 9263 connects to the AI in the 6008 in this example.
Solved!
Go to Solution.
Attachments:
Test Pulse.vi ‏117 KB

I talked to a specialist in the phone and tols me that it is not possible.

How to acquire analog signal and send a TTL pulse at the same time based on PXI 6123

Hi,
I am using a PXI-6123 data acquisition card, as the picture show in the attachment ,I want to acquire the analog signal of ai0 through reference analog window and at the same time send a TTL signal to trigger my camera. I have tried two methods, one is using the DAQmx Export signal.vi another is using DAQmx connect terminals, but when the data acquisition card acquire the analog signal, the DAQmx Export signal.vi and the DAQmx connect terminals sometime can send an TTL pulse ,sometime can not.
I don’t know why? or some other method that can achieve my arm is appreciated.
Regards
chunlei
Attachments:
method export signal.vi ‏21 KB
method connect terminal.vi ‏36 KB
Send a TTL pulse.JPG ‏288 KB

Hi,
Have things changed over the years?
I need to syncronise a digital output (Modul NI9474) and an analoge input (AI-Modul NI9203) module. I need to measure time intervals from a flank in signal A to a flank in signal B. I would like accuracies of the order of 1 ms. Currently, the signals are not synchronised, with errors of the order of 2 times the block length (block size x sample rate), sometimes much higher. The best I got so far was a block size of around 20 with a sample rate of 1 kHz.
If I use the master and slave settings on the RTSL settings, my program doesn't run properly.
If I use digital signals for input and output, I can syncronise them with RTSL settings and everything is good, but I can't always do that.
Also, if I do anything in the GUI (such as scrollowing something or going to another window), my output gets screwed up properly.
1. What can be done to synchronise AI with DO?
2. Is there something that can be done to avoid messing up the output when something happens in the user interface? (I know that I am messing up the outputs as they make some valves switch and that is loud).
Thanks in advance!

Qosmio G30-126: how to connect analog TV and satellite TV simultaneously

Similar Messages

Maybe you are looking for