Qosmio X300-13G - Cannot connect to WLan router using N draft

Hi
I've bought a Qosmio X300-13g (the only one availabe on Portugal :/ ) and i've tried to connect it to a wirelles N network, but I always receive an error:
windows couldn't connect 'cause the defenitions of the router are different from yours...
Well do you know why? I've tried with several routers and it's always the same..
Tks
Regards

Hi
Yes, i've tried with a SMC WBR14S-N2 and now I'm using a Sitecom 300N (wl-183 / wl-541), I only receive the error when I choose the N mode, when I try the Mixed (G-N) it works (the computer connect with the G mode)
Thanks

Similar Messages

Satellite Pro 6100 - Cannot connect to WLAN router

Hi there,
I have brought a 2nd hand Satellite Pro, Model version SP6100 (PS610E-029ZV-EN), P4 1.7Ghz, 512Mb, 30GB, with Windows 2000 Pro loaded.
I cannot get the wireless to connect to my router. The switch is in the correct position.
I want to change to XP using the key supplied with the laptop from new (dual OS) however I can't get it to reformat using an XP disc at start up or if I use the recovery cd (start with holding C down and release when it runs up) it begins but displays "invalid drive specification" three times and loads Win2000.
Can anyone advise how (or if!) I can reformat as I would like?
Any help will be greatly appreciated.
Cheers.

Hi Jaba,
I'm quite happy to 'start again' and erase the existing partions via reformatting however I do not know how. I have tried starting with the XP disk in the dvd drive but it starts up in to 2000 without reading the XP disk.
I would prefer WXP than W2000 as it will be for home use.
If you or anyone else can advise on how I proceed from here I would be very grateful.
Cheers All.

After updating my iPad 2 to iOS 6, I cannot connect to my router. I have turned the router off, left off for a considerable time, turned the iPad off and on, reset the network settings, nothing works. Any other suggestions?

After updating my iPad 2 to iOS 6, I cannot connect to my router. I have turned the router off, left off for a considerable time, turned the iPad off and on, reset the network settings, nothing works. Any other suggestions? It is obvious many others are having similar problems, so the iOS 6 looks like a loser.

I have just upgraded from a 3 to a 4S and now I can't connect to my wifi. I've tried everything, resetting network settings, switching to boot, renewing lease, rebooting, turning off cellular data etc etc. nothing works!! Very frustrating!

I cannot connect to the net using 3G, i have ipad2 16GB, i have tried resetting my ipad2, and resetting the network setting, my location is here in riyadh, everitime i try to connect to the net theres a pop message saying "could not activate cellular data

i cannot connect to the net using 3G, i have ipad2 16GB, i have tried resetting my ipad2, and resetting the network setting, my location is here in riyadh, everitime i try to connect to the net theres a pop message saying "could not activate cellular data network, please help me guys thanks.....

Thanks for the quick response. No, I did not get any error messages or any terms-of-usage screen. The employee I told my problem to was not computer savvy either. She just suggested I move to different spots w/in the library to see if that would make a difference. It didn't. When I connected to the library WiFi it did change the Verizon 3G that is usually in the upper left corner to iPad with two to three emanating arcs. I may have to go to the library in the next town. I was able to connect to theirs in the past when I had to download something greater than 20 MB. Unless I really want it, I will probably not even try to download something more than 20 MB due to the hassle. Yeah, I may have been better off getting a normal desktop or laptop and getting WiFi at home. To do that now would mean having my iPad 2 and a desktop computer, which I feel is extravagant. (I know there are a lot of big spenders out there who got the iPad as additional gadget for fun. This is a rich country.) A Verizon rep told me I couldn't set up a WiFi router at home just using an iPad. So it seems like a person who just uses 3G is limited to surfing the net (not even much YouTube because it eats a lot of data) and using email. I read about an app that helps print wirelessly using 3G, but a reviewer said you had to be an engineer to get it done right. BTW, I like the Steelers. I'm old enough to remember Franco Harris and that blond guy whose name escapes me back in the '70s. Since I live in North Jersey I feel I have to support the Giants. But I know football about as well as computers.

I cannot connect to the internet using apps but im connected to the internet!

i cannot connect to the internet using apps but im connected to the internet!

What makes you think that you are connected to the internet then?
Try:
- Resetting the iPod. Nothing will be lost.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
- Reset ntwork settings: Settings>General>Reset>Reset Ntwork Settings.
- iPhone and iPod touch: Troubleshooting Wi-Fi networks and connections

My Macbook Pro cannot connect to the internet using an ethernet cord.

My Macbook Pro cannot connect to the internet using an ethernet cord. It was working fine for weeks, then all of a sudden just stopped. What could the problem be?

Hi bean07670,
If you are having an issue with the Ethernet connection on your MacBook Pro, you may find the following article helpful:
Mac OS X: Troubleshooting a cable modem, DSL, or LAN Internet connection
http://support.apple.com/kb/TS1317
Regards,
- Brenden

TS1368 I cannot connect to iTunes store using iTunes. 'Secure link to iTunes store failed'. Please help!

I cannot connect to iTunes store using iTunes. I have version 11.0.2.26 on Win 7 pc. I have had no problems until recently. Can't say exactly the problem began as I don't normally use my computer to access the store but my last successful access according to iTunes diagnostics was 28th Feb 2013 (if thats useful?!)
I've run the Network Connectivity Test in iTunes diagnostics and I got the following results:
- Network interfaces verified.
-Internet connection verified.
-Secure link to iTunes failed.
When I click the help button next to the 'Secure link to iTunes failed' message I get the following:
''iTunes Help is unavailable because your computer isn't connected to the internet.'
My pc is connected to the internet. I've checked firewalls. Windows firewall is off. I'm running AVG internet security 2013. Iv've checked the firewall settings on that and iTunes is not being blocked.
Getting kinda frustrated. Can anybody help please???

I seem to have tracked down the problem. AVG Family Safety software was causing the issue somehow. I have uninstalled it and iTunes now working. I will contact AVG for a solution as I now have no way of blocking certain sites.

My pc cannot connect to iphone 4 using bluetooth,says no bluetooth driver.

my pc cannot connect to iphone 4 using bluetooth,says no bluetooth driver.

What exactly are you trying to achieve by connecting via bluetooth? If you have a tethering plan, that's the only thing that's supported via bluetooth to a computer. It cannot sync or transfer files via bluetooth. Those are not features of the iPhone.

Cannot connect to the net using my wi fi on my blackberry curve

hi there, i cannot connect to the net using my wi fi on my blackberry curve 8520. wen i go in to settings and click on to manage connections it as a tick at the side of wi fi and says TALKTALK- 3B0BD4 and a tick at the end. if i turn my mobile network of my signal goes, and when i try to connect to the net a message comes up saying unable to connect to the internet, please try again later. if the problem persists please contact your service provider.when i try to set up a new wi fi connection and scan for networks it comes up with TALKTALK-3B0BD4 and undernieth it says connected and the signal is full at the side of it? many thanks maria

i cannot browse the internet thru wifi using bb curve 9360..when i checked my wifi settings it says that im already connected but when im trying to browse it says cannot connect contact your service provider

Cannot connect to FMS 4 using rtmfp

Hi people,
I was try to connect my FMS 4 development server (Redhat linux OS) in live which was not connected, but the same setup in local windows is connected.
I do know whats the exact problem. Also i will stop the iptables in linux but no use. Please any idea, its worthful.
thanx and regards
Suresh

Hi Nikhil,
Appreciate your reply.
Both Firewall and the SELinux are disabled. But still cannot access the FMS
Server using http://ip-address. Windows installation works perfectly. But
still I can Telnet to port 80,1935 and 111 in the Linux installation. This
is weird. I don't know why the only the Linux setup is not working. Any
idea that I need to change any configuration in the Linux setup? Here is
the Linux version I've installed,
Re: Cannot connect to FMS 4 using rtmfp# uname -a
Linux GSMedia 2.6.18-274.12.1.el5 #1 SMP Tue Nov 8 21:37:35 EST 2011 x86_64
x86_64 x86_64 GNU/Linux
Re: Cannot connect to FMS 4 using rtmfp# cat /proc/version
Linux version 2.6.18-274.12.1.el5 ([email protected])
(gcc version 4.1.2 20080704 (Red Hat 4.1.2-51)) #1 SMP Tue Nov 8 21:37:35
EST 2011
Re: Cannot connect to FMS 4 using rtmfp# cat /etc/redhat-release
Red Hat Enterprise Linux Server release 5.7 (Tikanga)
Thank you.
Viraj
From:     Nikhil Pavan Kalyan <[email protected]>
To:     Kularatnav2012 <[email protected]>
Date:     01/05/2012 03:57 AM
Subject:     Re: Cannot connect to FMS 4 using rtmfp Cannot connect to FMS 4 using rtmfp

Cannot connect statefully to AuroraServer using inst1_http

I tested inst1_http using Net8 successfully. But when I run the url on the brower, I got "Cannot connect statefully to AuroraServer using inst1_http" message on the error.log file. Could some one let me know the cause?
Where can I find the log information about mod_ose, and ose?
Thanks,
Lixin

I am on Win 7 64 bit. iTunes and one other program I use could not make a secure connection although I was able to securely connect to online banking, etc. I tried ten different settings I read about in various posts under "Secure Connection" including the links about in your post. Nothing worked.
What finally worked for me was going into Control Panel, then selecting Internet Properties, then going to the Advanced tab, and then scrolling down to the Security section and unchecking "Check for server certificate revocation*" Note that I undid trusted sites (e.g. no trusted sites needed) and undid all the special Norton IS 2009 firewall settings and everything still worked. This seemed to all start with the updates starting with iTunes rev 9 but I can't be sure as I recently upgraded to Win 7 Premium Home from Vista Ultimate.
Hope it works for you. I will post this in a few other discussions on the same as I have not seen anything before that worked in my case.
Good luck.

My iphone 4s cannot connect the internet sometimes using the 3G, but sometimes it does work. i do not know what is wrong ?

my iphone 4s cannot connect the internet sometimes using the 3G, but sometimes it does work. i do not know what is wrong ?

5.0.2 has not been released, thus you can not upgrade.
Stedman

MacBook Pro Cannot Connect to Wireless Router

I have a brand new MBP and it won't connect to any non-apple wireless routers
- my computer is 2 days old (it's awesome and I love it accept that I can't get wireless connection at home)
- wireless router: westell versalink model 327 W
- PROBLEM: my mbp will detect the network just fine, but won't connect to it...just times out, it will connect to a neighbors linksys, but cannot load any internet pages, so still not helpful. When I try to connect to the wirelesss router using the network utility it asks for a WEP password, which it never did before because it's an open wireless router. (I know you should always password protect, but it's not my router...I'm just in the same house)
- I had a powerbook G4 and ibooks that have all connected fine to the same wireless network. My dad has an HP laptop that also connects fine
- it only connects to the apple brand airport wireless routers
- it will connect to the wireless router if I plug in the ethernet cord
- I have tried checking the connections, allowing all connections, repairing my disk permissions (even though my computer is only 2 days out of the box), resetting the router, opening the router so no password is needed...NOTHING WORKS!
- I also tried another wireless router (netgear): doesn't work
I've been reading around in some forums and this seems to be an apple and maybe more specifically a macbook pro issue (just by process of elimination). One forum said that it was because of an airport update that basically "breaks" mbp's airport and makes it not accept any non airport wireless connections, apple supposedly is working on a fix but who knows
I'm feeling disappointed and very upset that this is even a problem, especially with how many people I read are dealing with the same issue wit still no solution. My mbp was far from cheap and this just shouldn't be an issue. I'm planning on contacting apple and getting to bottom of this or at least some kind of answer.

- it will connect to the wireless router if I plug in the ethernet cord
this is because there is an actual physical connection between the router and the machine, so the router allows the connection automatically. i believe ALL wireless routers have a "Wireless Access List" in their config. the owner of the wireless router must add any machine or device seeking to gain access to the wireless router. consult your routers documentation on how to access the router from a web page and add your machine. this is usually done by adding the machine's mac address to the wireless access list. i added my 15"mbp and iphone to my netgear wireless router in about ten minutes and have no problem connecting every time.
also, when making any changes in Network Preferences, be sure to "Apply" after any change or adding any wep key. let me know if you have any questions.

LaserJet Pro CP1525nw cannot connect to new router (Home Hub 2000)

In December, we replaced everything EXCEPT our LaserJet Pro CP1525nw colour printer - new laptop (Dell Inspirion 15), new operating system (Windows 8.1 - 64 bit), new internet provider (Bell) and new wireless router (Home Hub 2000).
Immediately, we were unable to connect to the router. We tried all of the suggestions, including connecting the printer directly to the router - which worked, until we disconnected it and then they could not communicate again.
At the time, the only solution we could find was to connect our printer and laptop via USB cable and print that way - no more wireless printing, so unable to print from phones and iPad, but at least we could print from the laptop.
In the past month, we have become unable to use many of the features on our printer - when we try to select print options, we get the message "HPMSN103.dll has stopped working." So, we can still print, but cannot select options.
We have tried using the CD that came with the printer, and it gets to a certain point and then a fatal error occurs. We have tried downloading the "full solution" printer install program from the HP website, and the same thing happens. We have tried skipping that and just choosing the appropriate printer driver in Windows: if we only use that driver, we get a printer that shows up, but we cannot print if we select it (interestingly, though, we can actually access the printer options!); if we say we have the disc, then we get two printers showing up - we can select print options on the one that will not allow us to print, but not on the one that actually prints. If we try removing one of the printers, they both uninstall and we're back to square one.
So, we WANT to be able to get back to printing wirelessly - after all, we paid (handsomely) for a wireless printer! And we still cannot get our printer and the router to recognize each other. Can somebody help? We don't want to have to buy another printer.
Thanks!

Hi @Capers2 ,
I see that you are experiencing issues setting up the printer on the new router. I will certainly do my best to help you.
Thank you for providing that detailed information.
If the network name has any spaces or special characters, the printer may not recognize it.
The printer is only capable of sending/receiving in the 2.4 ghz band.
If it is set to 5 GHZ network you may need to change to 2.4 ghz. (rename the 5 ghz or shut it off)
The WPA key setting needs to be on AES to work correctly not TKIP.
Multi casting needs to be turned on.
Firewall on router has to have open ports for printer.
If you have Mac Filtering you need to give printer hardware address from Configuration page.
You might need to contact your router company for further assistance to check those settings.
I would reset the printer first to clear out any previous network settings.
Turn the printer off, hold down the wireless button and cancel (x button) while turning the printer back on and don't release the two buttons until the printer stops making noise.
Print out a configuration report and make sure the SSID and IP address are cleared.
Printing a Configuration Page.
The easiest way to setup the printer back on the wireless network is through a Ethernet connection and then switch over to wireless.
Disconnect the USB cable.
Remove any printer software by following these steps:
Go into Devices and Printers , click file then Server Properties, click on the Drivers tab at the top of print Server Properties window. Choose the printer you want to uninstall and click remove. Choose remove driver and package. Any that say Universal PCL 5 or Universal PCL 6 also remove and the Laserjet CP1525nw.
The next screen will give a warning, letting you know that deleting the driver package will remove it from the system. Click yes to say that you are sure you want to do this. (if the printer isn't listed that is OK)
Right click and delete any entries for the Laserjet in the Devices and Printers Window.
Run the uninstall from the CD.
Press the Windows key and the X key together. and select File Explorer, right click the CD for the
printer and left click open in new window.
Connect the printer to the router with a Ethernet cable.
Wait about 1 minute and the printer should have a valid IP address.
Print the configuration page to get the printer's IP address to configure the Wireless.
Type the IP address in Internet explorer's address bar which should open the printer's embedded web services page.
Setup the wireless through here now.
Click on the networking tab, wireless on the left, fill out the network information and apply the settings.
After the confirmation, then disconnect the Ethernet cable.
Now you should have a blue wireless light on the printer in about 1 minute.
Perform a clean boot on the computer and turn off the Antivirus Software. How to perform a clean boot in Windows.
Run the installation again.
If you are prompted to connect the USB cable during the installation, Then immediately after connecting the USB cable, follow the steps in this document to update the drivers so it doesn't error out. A Fatal Error Displays During Software Installation. Then the installation should continue.
Test the printer.
If there is anything else I can help you with, just let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Equium L10-300: Cannot see my Wlan router!

I have a Toshiba Equium L10 300 laptop with an internal Infocomm IPN 2220 wireless network card.
The laptop is running Windows XP Home SP2 and ConfigFree. I have updated the wireless drivers to the latest version.
I am trying to connect the laptop to a Belkin ADSL Modem with Wireless G Router (Model: FSD7632-A)
The wireless button is turned on.
When I refresh the wireless LANs in either windows or configFree, I can see every wireless LAN SSID on my street (which are also 54G) apart from mine. I have a other laptop which quite happily connects to the Belkin. The L10 stubbornly refuses to acknowledge its existence.
Does anyone have any idea why this is?
Any help woud be much appreciated.
Regards,
Alasdair

Hi
The WLan card seems to works because the other WLans are visible.
In my knowledge the integrated Ambit minPCI WLan card support 802.11b/g wireless technology.
I would recommend switching the mode to G only. This can be done in device manager -> WLan card properties -> advanced tab
Please also check if the Wlan card uses the same channel like Wlan router.

Qosmio X300-13G - Cannot connect to WLan router using N draft

Similar Messages

Maybe you are looking for