QSIG VoIP Connection CCBS feature

We are connecting three PBXs wit VoIP.
Using 1760-V with 12.3(4)T11 images, VWIC-1MFT-E1 interfaces and isdn Q.SIG.
Our PBXs vendor and our customer wants to use CCBS
(call completion to busy subsriber).
But there we could not find any documentation, if this feature is supported or not.
And which IOS version to use.
Many thanks in advance.
August

Hi there,
QSIG with supplementary services is supported only with MGCP and with PRI backhaul in conjunction with ccm (this means the voice gateway passes the information to the end pbx).
http://www.cisco.com/en/US/partner/products/sw/voicesw/ps556/products_administration_guide_chapter09186a00803edb19.html#wp1139777
an example between avaya, ccm and how to configure 3745:
http://www.cisco.com/en/US/partner/tech/tk652/tk701/technologies_tech_note09186a00803d22cd.shtml

Similar Messages

Broken VoIP connection E61 to asterisk server afte...

After upgrading and restoring settings from backed up data the mobile phone finds it's WLAN connection and shows an established VoIP connection (as before).
But no incoming or outgoing calls are possible over VoIP. At server side nothing was changed.
Asterisk logs the following at session initiation:
-- Registered SIP 'XXX' at 192.168.1.184 port 5060 expires 3600
-- Got SIP response 400 "Bad Request" back from 192.168.1.184
When trying to call the phone:
-- Got SIP response 488 "Not Acceptable Here" back from 192.168.1.184
-- SIP/XXX-69d3 is circuit-busy
== Everyone is busy/congested at this time (1:0/1/0)
Anbody any ideas?
Thanks in advance.
Nazdravi

as far as i know, you'd need xsan nodes for all machines involved and san storage shared among all nodes. ideally, you'd need primary and secondary xsan metadata controllers just to deal with san metadata, and they should not be your od master or replica.
you could probably skimp on hardware and double up services on each machine, but it probably wouldn't save you much in the short term, at least.
how about moving to more power efficient processors for your current setup? your network as it is now sounds exactly like what some of my clients would love to have, but it would take a lot of cash to build with apple hardware/software.

VOIP connectivity with BIAMP Tesira DSP

Hello All,
We are looking at hooking a BIAMP Tesira DSP into our Lync 2013 server to handle VOIP calls in our conference room. The unit has an add in module specific for handling VOIP connectivity (SVC-2) but I haven't been able to find any documentation on how
to go about configuring it for a Lync server.
Has anyone ever worked with one of these or have any ideas on where to start?
Thanks!

Hi,
I agree with Holger Bunkradt. You need a Microsoft Certified Media Gateway or a SBC between Lync Mediation Server and the BIAMP Tesira DSP.
You can choose from the link below:
https://technet.microsoft.com/en-us/office/dn788945
Best Regards,
Eason Huang
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Eason Huang
TechNet Community Support

Cisco 7206VXR (NPE-G2) Error - %SW_MGR-3-CM_ERROR_FEATURE_CLASS: Connection Manager Feature Error: Class SSS: (QoS) - install error, ignore.

Dear Cisco Expert,
We are facing problem terminating PPPoE users on Cisco 7206VXR NPE-G2 router where in user connects to router but policy-map is not applying on user interface.
Below mentioned message is logged on router.
%SW_MGR-3-CM_ERROR_FEATURE_CLASS: Connection Manager Feature Error: Class SSS: (QoS) - install error, ignore.
Below is the "show version" output.
Cisco IOS Software, 7200 Software (C7200P-ADVIPSERVICESK9-M), Version 12.2(33)SRC, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 11-Jan-08 02:44 by prod_rel_team
ROM: System Bootstrap, Version 12.4(12.2r)T, RELEASE SOFTWARE (fc1)
aggr03 uptime is 1 day, 6 hours, 4 minutes
System returned to ROM by reload at 05:45:18 IST Wed Sep 3 2014
System restarted at 05:46:53 IST Wed Sep 3 2014
System image file is "disk2:c7200p-advipservicesk9-mz.122-33.SRC.bin"
Last reload reason: Reload command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 7206VXR (NPE-G2) processor (revision A) with 1966080K/65536K bytes of memory.
Processor board ID 31782123
MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2
6 slot VXR midplane, Version 2.7
Last reset from power-on
PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb1 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port Adaptor
Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>
for c7200 bandwidth points oversubscription and usage guidelines.
1 FastEthernet interface
3 Gigabit Ethernet interfaces
2045K bytes of NVRAM.
500472K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes).
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
Can somebody help please?
Thanks,
Nilesh.

Hi Inayath,
We are applying policy-map on user virtual-interface via radius attributes.
Cisco-Avpair+="lcp:interface-config#1=service-policy input 256k"
Cisco-Avpair+="lcp:interface-config#2=service-policy output 256k"
Below is the relevant configuration for cisco router.
aggri03#sh policy-map 256k
Policy Map 256k
    Class 256k
     police cir 520000 bc 32000
       conform-action transmit
       exceed-action drop
aggri03#sh run int virtual-te1
Building configuration...
Current configuration : 398 bytes
interface Virtual-Template1
mtu 1492
ip unnumbered Loopback100
no ip redirects
no ip unreachables
no ip proxy-arp
no logging event link-status
peer default ip address pool poolname
no snmp trap link-status
keepalive 60
ppp authentication pap callin
ppp ipcp dns 203.187.x.y 203.187.x.y
ppp timeout ncp 30
ppp timeout authentication 20
ppp timeout idle 480
end
Below is the complete log line on router.
Sep 3 16:41:31: %SW_MGR-3-CM_ERROR_FEATURE_CLASS: Connection Manager Feature Error: Class SSS: (QoS) - install error, ignore.
-Traceback= 4A9C88 4AAC20 4AB350 12B6040 12C8B38 2C2F24C 2C2F2FC 12C8E0C 12C9000 12C94D0 12B4788 12B4D40 12B4E84 12AFEB0 12B02FC
Please let me know if you want further information & thanks for your inputs.
Thanks,
Nilesh.

Caller ID problem between 2 PBX's across Cisco VoiP connection

Hi all,
I have two Cisco 2811 Routers connecting 2 Avaya Index PBX's via T1/E1 cards (configured for E1)across a LES 10 circuit. Everything works fine but the problem i have is when phone1 (John) at site A dials phone2 (James) a site B, the incoming number is shown but not the name of the person. When 2 calls are made within a site, the name of the calling party is shown (not the directory number). Can someone please shed some light on if this is possible across the VoiP connection and how i would configure it. I have attached the configs to help.
Thanks in advance,
Gary.

Ideally there should not be any line code violations on the data T1 at all.
Violations are at the data T1 and the voice T. And they shud be avoided.

Connected No Feature

Other than during Intercom, what puts a phone in the Connected No Feature call state for softkeys?

The iPad has it's own community forum:
https://discussions.apple.com/community/ipad
All the expert iPadders are there.

Choppy voip connection

I have 1MB wireless link from my ISP. I am using Cisco VOIP phones in my company. Over the months my VOIP quality is not good(on/off connectivity),though my internet is somehow working fine. When I talked to my ISP , they told me to use Cisco switch / router instead of Nortal. Moreover ISP also saying that the switch / router can be configured to full duplex/ half duplex because ISP equipment can be switched to half/duplex.
-->My questions.
1-what cisco router/switch should I use with voip phones ?
2-What duplex setting should be on the router/switch so voip quality be remains optimum.
3-Is 1MB link can be used for voip?
4-Is it possible to configure voip phones to full/half duplex ?
Please help. Thanks.

Hi,
2. If you're currently running your phones over a wireless connection, this can cause problems. Wireless doesn't have guaranteed bandwidth and it's half duplex.
If you were to switch this out with a router and switch, you could make every link full duplex.
Full duplex is what you should run everywhere. The only modern technology you should be running half-duplex on is wireless, because that's just the way it works.
1. The router depends on your company size and what you want to use it for.
3. 1 MB link may be alright, but again, it depends on how many active phone calls, what your data usage is, and what codec you're running.
4. Phones are auto-negotiating, and they will use either.

Multipoint VOIP Connection

Good Afternoon,
I want to connect through VOIP 15 different points.
Each point has 1 POTS Line and 1adsl Line. Each Point has Static IP address.
I want to use VOIP only for calls between those 15 points.
I am thinking to use SPA3102 to each point with analog devices.
All external calls will be redirected to the POTS line and all calls between the 15 points will be redirected through VOIP to the other point.
Is this possible to be implemented?
Do I need any extra Hardware to implement this? Like a SPA900 somewhere?
Is SPA3102 the appropriate device to do this?
The router each point is using is a CISCO B107. Are there any issues continue using this hardware?
Thank you very much in advance for your interest
dvachtse

I think the only way to do this and keep it manageable is to setup a PBX at one site. You could probably pull it off with an SPA9000, but you are right at the maximum number of connections and routing would be a pain. If it were me I would setup a trixbox at one location.

VoIP connection to PABX

Essentially, I'm trying to extend a analog line from a Nortel PABX across a data network to a slightly out of reach phone.
I have 2 routers (2801) equipped with FXO and FXS cards each. I want to extend a analog line (RJ11) from the PABX to the router with the FXO card and from that router to another router with a FXS card, and from there, to a POTS phone. The PABX would provide an extension to the phone, and would route calls to that extension to the connected port on the router. On the other hand, the router with the FXS card would capture whatever number the phone dials and just pass it straight alot to the PABX.
Is this possible? I've been reading reference material all week trying to figure it out.

Hi,
for the HQ router with 4 FXO's i have:
voice-port 0/3/0
input gain 2
output attenuation -4
timing hookflash-out 500
connection plar opx 200
impedance complex1
voice-port 0/3/1
input gain 2
output attenuation -4
timing hookflash-out 500
connection plar opx 201
impedance complex1
voice-port 0/3/2
input gain 2
output attenuation -4
timing hookflash-out 500
connection plar opx 202
impedance complex1
voice-port 0/3/3
input gain 2
output attenuation -4
cptone ZA
timing hookflash-out 500
connection plar opx 203
impedance complex2
dial-peer voice 5572 pots
destination-pattern 5572
port 0/3/0
dial-peer voice 5852 pots
destination-pattern 5852
port 0/3/1
dial-peer voice 5815 pots
destination-pattern 5815
port 0/3/2
dial-peer voice 5853 pots
destination-pattern 5853
port 0/3/3
dial-peer voice 200 voip
destination-pattern 20.
session target ipv4:10.61.156.1
incoming called-number .
dtmf-relay h245-signal
no vad
and for the remote site with 4 FXS i have:
voice-port 0/2/0
input gain 2
output attenuation -4
cptone ZA
connection plar 5572
voice-port 0/2/1
input gain 2
output attenuation -4
cptone ZA
connection plar 5852
voice-port 0/3/0
input gain 2
output attenuation -4
cptone ZA
connection plar 5815
voice-port 0/3/1
input gain 2
output attenuation -4
cptone ZA
connection plar 5853
dial-peer voice 200 pots
destination-pattern 200
port 0/2/0
dial-peer voice 201 pots
destination-pattern 201
port 0/2/1
dial-peer voice 202 pots
destination-pattern 202
port 0/3/0
dial-peer voice 203 pots
destination-pattern 203
port 0/3/1
dial-peer voice 100 voip
max-conn 4
destination-pattern 5...
session target ipv4:10.59.1.70
incoming called-number .
dtmf-relay h245-signal
no vad
Hope this helps

VoIP connection to company server

Hi there,
When reading the specs of the IPhone 3G I was interrested in its capability to connect to VoIP servers. I noticed there are lots of apps around which let it connect to skype like services. In other words: services for which you need an account and you place calls via the Internet.
This is not what I am looking for.
What I need is a replacement for the Nokia E series.
With the Nokia E series I can make a VoIP profile connecting to our company VoIP server. The profile becomes an intergral part in the phones methodes of placing and receiving calls.
This way I can place and receive calls through our company VoIP server when in range of our Wifi network. When out of range it switches to the network of the telecom provider (like Vodafone).
Is this posible with Apple IPhone?
Peter

Seems it is called ISip nowadays.... looks good.
Now all I need is an IPhone to actually test it .... thanks

Nokia E51 VOIP connection

I have E51 mobile phone and appreciate if anyone in the forum knows how to configure SIP settings for internet telephone using
VOIP. Can this be done with EQO or Sype services?

what do u mean by recording?
T18>6210>8310>6800>6210>7610>6680>6210>E50>3110>2610>E65>E61i

Share play 'test connection speed' feature.

Just found this new addition, but how accurate is it?
I'm wired up, and get 49mb down & 3mb up and my share play test result is 'slow' and it says 'your internet speed is not strong enough for share play'
Feel free to post your results.
PSN Sux.

ocelot07 wrote:
Mine seems ok shareplay has worked fine for me since it released. I tried the test earlier and mine only makes it to 2 yellow bars and the unfotunate fact is that 90% of Aussies cannot use shareplay because of our crap internet network, but it is being fixed up with the National Broadband Network that the goverment launched a few years ago, which just came to my area recently, meaning I now get 22 down 4 up, and 13 down 2 up on PS4........much better than the 3 down 0.5 up

Predictive Analysis 2.0 - 'BW' connect feature ?

Hello folks,
In the latest Predictive Analysis, do we have 'BW' data connect feature ?
BW offline connection or connection via Lumira is fine.
Looking forward to hearing any response. My customer'd like to know this.
Thanks a lot.
JH Yang.

Hi JH Yang,
Thanks for the post.
Yes, the BW Connect (offline) feature should be coming to SAP PA.
According to this post: http://scn.sap.com/thread/3571348
Also you find the full Roadmap for Predictive Analysis here: Product Road Map Updates
Best regards,
Kurt

Connected Devices iOS 8 feature and iPhone 4s

Has anybody found an issue where calls to an iPhone 4s running iOS 8 will cause any other iOS 8 device to ring when they are connected on the same Wireless LAN?
Currently, even though the 'Connected Device' feature is turned off on iPhone 5s and iPad Air, calls to my iPhone 4s cause those 2 other devices to ring.
I don't have a 'Connected Device' feature listed in my 4s, but if I'm on the same WLAN all devices ring. If i turn off wifi, then only the 4s rings.
Anybody found this issue and found a way to stop it from happening?

Yes correct even my iphone 4s is dead just after 2 days of installing ios8...how can i repair it now?
its really disgusting on part of Apple inc to launch ios 8 without giving any warnings for its use....

Router 2911 with voice card VIC3-E/M VOIP Problem

hi All
I want to ask if any of you have any experience like this. I have deployed a new Cisco router (model 2911) in my client. The previous router they used is 2811. After deployement, the WAN & LAN connection work fine, but the VOIP connection does not work.
The previous router (2811) uses a voice card module VIC2-e/m. But the new router (2911) use voice card module VIC3-e/m. It is used to connect to the PABX Panasonic TD-1232.
Could this be a factor?
Can anyone help?

Hi,
In addition to what Terry has said, the only change is IOS 15.1 where Toll Fraud Prevention feature was introduced which says
The router will automatically add any destinations that are defined as an ipv4 target in a VoIP dial-peer to the trusted source list.You can run the command
show ip address trusted list
To overcome this behaviuor, you can follow the three ways as suggested in below link .The one has been already suggested by Terry.
https://supportforums.cisco.com/document/46566/understanding-toll-fraud-enhancements-1512t
your 28XX router has 12.4 IOS version
regds,
aman

QSIG VoIP Connection CCBS feature

Similar Messages

Maybe you are looking for