Quad G5 - One processor runs 20 degreesF hotter than the other!

I use an app called Hardware Monitor to keep tabs on the various sensors in my G5. Today, for apparently no reason at all, CPU A (both cores) runs 20 degreesF hotter than CPU B!!! Not to mention 20 degreesF hotter than they ever did in the 4 months I've had the system. It does not matter if the computer is idle or if I give it a heavy work load, CPU A is always about 20 degrees hotter (it varies about 5 degrees -- for example, A is 122.3dF right now, and B is 103.0dF). I did a clean OS install on a different drive and took readings again, sure enough, it is the same. I removed all peripherals, check inside for dust, debris, etc... I can find no reason why this would happen! So far it has not been a problem, all the fans and pumps run at normal speeds. In the past my temps varied from about 98dF when idle, to about 150dF when under heavy load. CPU A now is 122dF - 165dF! Anyone have any ideas?

This is only speculation, but it may because your coolant is not flowing at peak efficiently. What could cause this? There are micro-channels the coolant flows through to cool the processors. They may be starting to clog up for some reason or another. If the processors get to hot, the unit will go into thermal shutdown, so you don't need to worry -- yet. I would keep your eye on it and if the unit shuts down while you are working on it, check your logs for lines with "thermal" in them and get the unit looked at. Your LCS may need to be replaced at that point.
Also, make sure you have/get AppleCare!
-Bmer
Mac Owners Support Group
Join Us @ MacOSG.com
 An Apple User Group 
ITMS: MacOSG Podcast >>

Similar Messages

Qosmio X300 - one Geforce 9800 GTS runs hotter than the other

Hi.....Does anyone have a clue why 1 of my 2 gfx cards seems to be running alot hotter than the other? I would assume they would both be roughly the same temp. This is an example...Nvidia Defaul @ 1680x1050
512MB GeForce 9800M GTS (Toshiba) 63 C
ForceWare version 186.42
512MB GeForce 9800M GTS (Toshiba) 49 C
ForceWare version 186.42
256MB GeForce 9400M G (Toshiba) 56 C
ForceWare version 186.42
SLI Disabled
When i exited playing F1 2010 yesterday, one of the cars was 90C and the other about 58C......Im sure that isnt right. !!!!
Also i see that it says SLI disabled....again i dont understand this, as i thought my rig automatically switched to SLI mode when needed.
These temp readings was taken from the program speccy.
My laptop is a Toshiba Qosmio X300-15U....running windows 7 ultimate 64 bit. 4gb ram. Q6600@2ghz.
Any help would be really apprieciated.
Thanks

Well i'm sorry you've had such clueless replies to your question.....if i had a cent for everytime a "regular" toshiba contributor says "use compressed air" or "only use Toshiba display drivers blah..blah`.....i'd be a very rich man!
The simple reason why only 1 of your 9800m gts cards is hot is because it is the only card being utilised in most games especially recent ones like F1 2010.
You see the toshiba graphics driver you have installed on your Qosmio is nearly 2 years old-and it doesn't contain any SLI profiles for games that have been released after this driver was created (mid 2009).
Just because you have 2 Nvidia GPUs in the laptop it does not mean that they are being utilised everytime-in fact it is totally dependent on having an SLI profile for specific program/game within the driver itself.
If you open the Nvidia control panel and go to advance settings/manage programs you can scroll down a list of sli profiles for programs installed on you machine and also view a complete list of all profiles within the driver.
It is possible to add you own sli profiles on this screen by browsing for a games executable and adding it to the list of preinstalled profiles.
However in my experience this rarely,if ever, produces much of a performance increase and can sometimes cause instability-and is no substitute for Nvidias own SLI profiles.
So.. the only way you can gain an SLI boost in games is by having the latest driver with the latest profiles....but wait i hear you say..
Toshiba haven't updated the driver for our laptop since 2009!!!
Yes thats the massive downside of owning a gaming laptop especially one as unique as Qosmio x300-just see my post in the Gaming forum-`Toshiba display drivers and what they don't want you to know' and i'm not gonna go into all that again.
All i say is that you can get some great advice on using modified Nvidia drivers on Laptopvideo2GO.com and if you go to the forums and look under Nautis1100 Hybrid and optimus drivers you'll find a new thread especially created for owners of qosmio X300s.
Good luck!

How to proportionally scale one side of a photo more than the other?

Does anyone have any suggestions as to how to scale one side of an image more than the other? I've tried Content-Aware scale but it always yields ugly results. Any help is greatly appreciated.
Peter

Hi Peter
I thik the main problem is the amount of the side of the column showing is making the right column appear larger.
I would therefore suggest moving part of the right side of the image slightly to the left.
You need to be careful in distorting the image as it will show up in the perspective on the floor.

CPU A Is hotter then the other

i check my iStat a lot and my system monitors and I have noticed that my Mac Mini has 2 CPU A's and the second one is always about 10 degrees or more hotter than the other one and everything else that is measured. It says CPU A and CPU A and the second one runs hottest. Is this normal? and if not what can I do?

Cores in Core Duo, Core 2 Duo and dual processor systems all tend to run at differing loads, and thus differing temperatures. What you're seeing is the two cores in your CPU, and more than likely if you were to run something like MenuMeters with the CPU monitor switched on and set to show the cores separately, you'd notice that one core is generally handling marginally higher loads.
That would mean the temperatures you see are normal. On the few instances I monitor internal temperatures on my systems, I see broadly similar results to yours for the same reason. As such, I'd say this is nothing at all for you to be concerned with - and indeed, that there is not much value in running such software as iStat since it gives you information that really doesn't have a useful context. If you find that the system doesn't correctly run the fan up to high speed when it should, that would be a good sign of a problem!

I have two iMac's one running 10.6.8 and the other 10.8.2 What Apeture program should I purchase?

I have two iMac's one running 10.6.8 and the other 10.8.2 What Apeture program should I purchase?

You can currently only buy the current version Aperture 3.4.3 at the AppStore, and that version requires MacOS X 10.7.5. at least, see the release notes: Aperture 3.4.3
So you will not be able to install this version on your Snow leopard machine. Maybe you can buy a boxed retail version of an earlier release, compatible with Snow Leopard, but the newer version is faster and compatible with iCloud.
Do your iMacs both have the same processors and memory? You will wan to use your fastest mac with the best graphics card and the most RAM to run Aperture, also a large screen would be desirable.
Regards
Léonie

Duplicates. I use iTunes match. When I run exact duplicates, I get duplicates that say uploaded for one and uploaded with a cloud for the other. Which one do I delete?

Duplicates. I use iTunes match. Two questions:
When I run exact duplicates on the library on my Mac Air, I get duplicates that say uploaded for one and uploaded with a cloud for the other. Which one do I delete?
Some of the duplicates say matched and matched with a cloud. Same question - which one should I delete?

I'm not sure I understand the question.
First I would update your iTunes match. iTunes match will tell you what is duplicates and then you can just delete them from the library.
Second, the course in a situation like this is to delete ONE duplicate and see what happens. Make sure you have that song backed up somewhere just incase it deletes it completely. But usually I'd delete one and then see if it deletes both or just the one you pressed.
Thirdly, update iTunes match. It usually does a good job of locating actual duplicates.

How to authorise more than one machine (1 tablet Android and one PC running Windows XP Pro) with the same Adobe ID ?

How to authorise more than one machine (1 tablet Android and one PC running Windows XP Pro) with the same Adobe ID ?

Cloud License allows 2 activations http://www.adobe.com/legal/licenses-terms.html
-Install on a 2nd computer http://forums.adobe.com/thread/1452292?tstart=0
-Windows or Mac does not matter... 2 on the same operating system, or 1 on each

Why is one slot saying 2.5gt/s and the other 5.0gt/s?

Hello,
I have a 2008 mac pro with 3.0 Ghz Harpertown processors. I thought these 2008 mac pros had two PCIe 2.0 slots, but yet according to my system profiler.. one slot is reporting at 5.0 and the other is 2.5 - what gives?
ATI Radeon HD 4870:
Name: ATY,MotmotParent
Type: ATY,MotmotParent
Driver Installed: No
Bus: PCI
Slot: Slot-1
Vendor ID: 0x1002
Device ID: 0xaa30
Subsystem Vendor ID: 0x1682
Subsystem ID: 0xaa30
Revision ID: 0x0000
Link Width: x16
Link Speed: 2.5 GT/s
ATI Radeon HD 2600:
Name: ATY,Lamna
Type: display
Driver Installed: Yes
Bus: PCI
Slot: Slot-2
Vendor ID: 0x1002
Device ID: 0x9588
Subsystem Vendor ID: 0x106b
Subsystem ID: 0x00a6
Revision ID: 0x0000
Link Width: x16
Link Speed: 5.0 GT/s
Shouldn't both slot 1 and 2 be PCIe 2.0?? Why is one being reported as 1.1 and the other is being reported as 2.0? Is there something wrong with my PCIe slot?? I am saddened to hear this as I traded up my 2006 mac pro and now I see that i am not getting 2 x PCIe 2.0 slots as reported.

DpArt,
Are you sure that is what the problem is? When I get home from work tonite, I will try to swap the cards and see. Originally, my harpertown mac shipped with the ATI Radeon 2600 XT, a very mediocre card and its in slot 2 reporting 5.0, while the ATI Radeon 4870 is a 1GB slightly overclocked(applemacanix) flashed card and its in slot 1 reported as 2.5 which I am hoping that this is an oversight and not a mechanical failure or problem with my pcie slot.

It's hotter than the Sun!!

Scott1408 wrote:
Running smooth as liquid metal. I would probably be more of a plasma at that point.

According to most website the Centre of the Sun is around 15Million °C
Well, some people in the office sometimes complain about the temperature and make silly comments like "It's hotter than the SUN!". Well normally i just laugh.
Well today might be the day these people are right, we had a new Datto device installed on Friday to start taking control of the Servers here and well this is what is being displayed!
Yes that's 4Billion °C!!!! Hope the AC in the server room can cope with this heat :)
This topic first appeared in the Spiceworks Community

How do I make one account's home folder visible to the other?

How do I make one account's home folder visible to the other? Also, when I begin to delete an account, it asks if I want to either delete its home folder, keep it in the users folder, or save it in a disk image. I want to be able to see it from my remaining account once I delete it, so if I leave it in the users folder, would I be able to see all the files (right now I can't

Use terminal to add ACL to the account,
at the prompt:
sudo chmod -R +a "<user> allow list,addfile,search,delete,add_subdirectory,delete_child,readattr,writeattr,readextattr, writeextattr,readsecurity,file_inherit,directoryinherit" /User/<user_name> #yep, all that goes on one line!#
#Replace <user> with the user name that you want to have file/folder privileges#
#Replace <user_name> with the account you want to process#
example:
sudo chmod -R +a "sue allow list,add_file, .... deletechild,readsecurity,file_inherit,directoryinherit
/User/joe
#sue now gets full access to joe's files and folders#
to remove:
sudo chmod -R -a "sue allow list,add_file, .... deletechild,readsecurity,file_inherit,directoryinherit
/User/joe
You can add as many users as you want! Just lather, rinse repeat. That is how I share my itunes
directory with the ones I want to share it with.
That's the simplest way. ACL permissions overrule posix permissions.

Jasper report on HTML when one image loaded from database and for the other

How to generate jasper report on HTML when one image loaded from database and for the other we give a image path
My code
ByteArrayOutputStream baos = new ByteArrayOutputStream();
          exporter = new JRHtmlExporter();
          exporter.setParameter(JRExporterParameter.JASPER_PRINT, print);
          exporter.setParameter(JRExporterParameter.OUTPUT_STREAM, baos);
          exporter.setParameter(JRHtmlExporterParameter.IMAGES_URI, strImageInputDirectory);
     exporter.setParameter(JRHtmlExporterParameter.IMAGES_DIR_NAME, strImageOutputPath == null ? "." : strImageOutputPath);
     exporter.setParameter(JRHtmlExporterParameter.IS_OUTPUT_IMAGES_TO_DIR, Boolean.TRUE);
     exporter.setParameter(JRHtmlExporterParameter.IS_USING_IMAGES_TO_ALIGN, Boolean.FALSE);
     exporter.setParameter(JRHtmlExporterParameter.IS_WHITE_PAGE_BACKGROUND, Boolean.FALSE);
          exporter.exportReport();
          byte[] bdata = ((ByteArrayOutputStream) baos).toByteArray();
Can any one help pls
Message was edited by:
ameet.au

hey sorry for posting it in this forum.
but do u have sample code for making it work.. since i am able to do it on PDF format(image from Database and another stored in the webserver) using
byte image[] =(byte[]) outData.get("image");
                    ByteArrayInputStream img = new ByteArrayInputStream(image);
                    hmimg.put("P_PARAMV3", img);
print = JasperFillManager.fillReport(reportFileName, hmimg, jrxmlds);
bdata= JasperExportManager.exportReportToPdf(print);

I have two Apple IDs - one associated with iPad and iPhone and the other associated with iMac and MacAir. I am going to lose the former e-mail address imminently and would like to associate all devices with just one ID. How do I do this? Thanks

I have two Apple IDs - one associated with iPad and iPhone and the other associated with iMac and MacAir. I am going to lose the former e-mail address imminently and would like to associate all devices with just one ID. How do I do this? Thanks

Thanks - I guess it is like there were two of me!
I bought the iPhone first and it seemed natural to link it to the (work) e-mail address which was in constant use. The iMac for home use came next and it seemed natural to use my home e-mail address, particularly as I knew by then that I would lose the work address after my imminent retirement. The same logic went for the recent puchase of the MacAir. I am not sure what happened with the iPad (also a recent purchase) - iTunes seemed to puch me towards the same ID as the iPhone.
It is not a huge problem - just makes my persona look schizoid! Otherwise very happy with everything Apple.

2 of my movies are no longer working in my iTunes or on my iPod Touch, One doesn't play at all and the other gets to about 29:00 than stops working and I don't want to buy them again. What's happening?

2 of my movies are no longer working in my iTunes or on my iPod Touch, One doesn't play at all and the other gets to about 29:00 than stops working and I don't want to buy them again. Then also when I added a non-iTunes movie and tried to have iTunes make an iPod/IPhone version it gave me error -4. What's happening to my movies?

I also have to add that the right earbud only doesn't work on my phone while i'm listening to music. If I'm face timing it's okay. what the heck.

I reset network settings on my iPhone. However now it looks as if my iPhone and iPad are no longer linked. They are both connected to my apple account but when I send an imessage from one it is not picked up by the other. What do I do?

I reset network settings on my iPhone. However now it looks as if my iPhone and iPad are no longer linked. They are both connected to my apple account but when I send an imessage from one it is not picked up by the other. What do I do? If anyone can help it would be very much appreciated. Many thanks x

Check Settings > Messages > Send & Receive on both your iPhone and your iPad to make sure that the following are all true:
(1) you have selected the same Apple ID on both devices,
(2) you have the same entries checked under "You can be reached by iMessage at:" on both devices,
(3) you have the same entry checked under "Start new conversations from:" on both devices,
and
(4) that the entry checked in #3 is one of those checked in #2 on both devices.
When you say it has affected your iCloud account, what effect has it had?

I am facing a weird problem with my iphone 4s Wi-Fi connectivity. As i connect my iphone to my office Wi-Fi, internet works in one building, but it doesnt work in the other building, although the phone shows Wi-Fi is connected. Please help me out!!

I am facing a weird problem with my iphone 4s Wi-Fi connectivity. As i connect my iphone to my office Wi-Fi, internet works in one building, but it doesnt work in the other building, although the phone shows Wi-Fi is connected in the other building. This problem was not there earlier but has occured recently. I would also like to mention that none of my other colleauges who uses iphone are not facing this issue. Please help me out!!

Assuming you entered the correct WiFi password for your network, see these articles:
iOS: Troubleshooting Wi-Fi networks and connections
iOS and OS X: Recommended settings for Wi-Fi routers and access points

Quad G5 - One processor runs 20 degreesF hotter than the other!

Similar Messages

Maybe you are looking for