Quark Xpress Passport can't find the printer in Mac OS 9

Help! Been fiddling and now can't print to my HP 6940. Don't know what I've done I'm so stupid!

Hello,
Sounds like you moved the drivers. I am a bit confused, this is 9 OS section, yor profile says
10.4 I think.
Either way, I would go here
http://www.hp.com/sbso/bussupport.html
and download new drivers. If you are running classic or both, be sure to install the drivers in the correct Operating system folder. This is easy if you are running OS 9 only.
My guess is you moved or disabled the driver. You could also try a sherlock search for the driver on your computer under 9, but this could get confusing.
I think I'd install new drivers from the web.
If this works, start a new thread for the PDF troubles and perhaps we all can help on that as well.........Jim

Similar Messages

HT2495 I have a wirless network. I connect all my computers to it and a printer. I can print wirelessly from all computers. I tried to add the printer to my new Macbook, but can't find the printer on the add printer and scan icon on preferences.

I have a wirless network. I connect all my computers to it and a printer. I can print wirelessly from all computers. I tried to add the printer to my new Macbook, which is connecte to the network, but can't find the printer on the add printer and scan icon on preferences. I downloaded a installation printer utility from the Manufacturer (lexmark), but it didn't work. Any sugestions?
Thanks,
Ivette

You would need to get the IP address of your printer then manually add a network print queue.
To get the IP address, on the control panel of your printer, press on Setup > Network Setup > TCP/IP > View/Set IP address.

HT3669 I have an imac running OS10.6.8 and an Apple laserwriter 16/600PS. Is it possible to connect these directly without networking? Where can I find the printer driver?

I have an imac running OS10.6.8 and an Apple laserwriter 16/600PS. Is it possible to connect these directly without networking? Where can I find the printer driver?

It turned out that WD is the big bad guy in this game.
According the data rescue company where I asked for an inspection, both of the drives had their reader head loose. And in the one, which was my already-in-use disk its even damaged the platters... xxxxx
So its time to pay bunch of money to recover, and take a walk to wd service to bang on the desk.
Also note - it may be somehow related to intellispeed technology - since macs not really friendly with wd-s built-in solutions.
On the other hand, with WD GP 1Tb there is no problems at all for ages.
thanks guys, thread is closed

When I try to take a print out from documents in my mailbox, it tell´s me that it can not find the printer??. I have just downloaded epson iprint since I have an Epson wifi printer. The iprint did find and succesfully installed the printer.

When I try to take a print out from documents in my mailbox, it tell´s me that it can not find the printer??. I have just downloaded epson iprint since I have an Epson wifi printer. The iprint did find and successful installed the printer. Somebody who knows what to do?

Chances are you Can only print from the app from the printer maker
And where you are Trying to print from May only work with AirPrint able printers which the epson would not be

Can't find the printer connection on Satellite M40

Silly question but I can't find the printer connection on my satellite M40? There looks to be a place for it on the left hand side of the notebook - there is a little printer sign, but the actual socket is covered over - should I remove it? and how do I do it? Help!!

Hello
As far as I know you can connect printer directly if you use USB port (newer printers). On the left side there are three ports:
- RGB (Monitor) port
- One USB port and
- PC Card slot
I really do not understand where you have found printer sign there.

How can i find the printing program?

hi
i have sap script how can i find the printing program ?
ami

ami bardogo wrote:
hi
what is the different between the commands 'break' and 'break-point'
thanks,
ami
h2 Breakpoints h2
Apart from being able to execute an ABAP program in the Debugger, you can also start the Debugger call by the choosing a breakpoint. This is achieved by setting one or more of these breakpoints in the program. A breakpoint is a signal at a particular point in the program that tells the ABAP runtime processor to interrupt processing and start the Debugger. The Debugger is activated when the program reaches this point.
There is also a special kind of breakpoint called a watchpoint. When you use watchpoints, the Debugger is not activated until the contents of a particular field change. For more information, refer to the chapter Watchpoints.
Breakpoint Variants
The Debugger contains different breakpoint variants:
Static
A user-specific breakpoint is inserted in the source code as an ABAP statement using the keyword BREAK-POINT. A non user-specific breakpoint is set in the ABAP Editor using the BREAK user name statement.
Directly set
dynamic breakpoints
Can be set in the ABAP Editor or the Debugger by double-clicking a line, for example. Dynamic breakpoints are always user-specific, and are deleted when you log off from the R/3 System.
Breakpoints
at statements
The Debugger stops the program immediately before the specified statement is executed.
Breakpoints
at subroutines
The Debugger stops the program immediately before the specified subroutine is called.
Breakpoints at function modules
The Debugger stops the program immediately before the specified function module is called.
Breakpoints at methods
The Debugger stops the program immediately before the specified method is called.
Breakpoints at exceptions and system exceptions
The Debugger stops the program immediately after a system exception, that is, after a runtime error has been intercepted.
Static Breakpoints
Static breakpoints are always user-independent if there is no specification of a user name. Once a user has inserted the statement BREAK-POINT or BREAK name in an ABAP program, the system always interrupts the program at that point for that user or only for the user name. This procedure is only useful in the development phase of an application when program execution is always to be interrupted at the same place. For more information, refer to the chapter Static Breakpoints.
In HTTP sessions, a static breakpoint is skipped if you did not set additional dynamic HTTP breakpoints in the editor of a BSP page. Instead, a corresponding system log entry is written, which can be checked using transaction SM21.
Dynamic Breakpoints
Dynamic breakpoints are user-specific. Therefore, you should use them if you only want the program to be interrupted when you run it yourself, not when it is being executed by other users. All dynamic breakpoints are deleted when you log off from the R/3 System.
Dynamic breakpoints are more flexible than static breakpoints because you can deactivate or delete them at runtime. They have the following advantages:
·        You do not have to change the program code.
·        You can set them even when the program is locked by another programmer.
·        You can define a counter that only activates the breakpoint after it has been reached.
Special dynamic breakpoints are useful when you want to interrupt a program directly before a particular ABAP statement, a subroutine, or an event, but do not know exactly where to find it in the source code. Event here is used to refer to the occurrence of a particular statement, for example, or calling up a method. Special dynamic breakpoints are user-specific. You can only set them in the Debugger. For more information, refer to the chapter Dynamic Breakpoints.
In HTTP sessions, the system stops both at static and dynamic breakpoints if a dynamic breakpoint was set in the editor of a BSP page before program execution.
Lifetime and Transfer of Breakpoints
A static breakpoint remains intact as long as the BREAK-POINT or BREAK-POINT name statement is not removed from the source code. Without saving, dynamic breakpoints only remain intact in the relevant internal session. However, they remain in effect during the entire user session if they are saved by choosing the menu path Breakpoints ® Save in the ABAP Debugger. For more details on the subject of user sessions and modes, refer to Modularization Techniques in the ABAP keyword documentation.
If you call an HTTP session during a user session, only the HTTP breakpoints are loaded when the HTTP session is started. You activate HTTP debugging in the ABAP Editor by choosing Utilities ® Settings ® HTTP Debugging. Depending on the setting, the system then displays either the HTTP or standard breakpoints in the Editor.
If you call an update session during a user session, breakpoints that were defined beforehand in the calling processing unit are copied to the new update session, where they can be displayed under Breakpoints. If, in the ABAP Debugger, you check Update Debugging under Settings and then, for example, call the update module func using CALL FUNCTION func IN UPDATE TASK, a new window is opened in which you can debug this function module in the update session. All the breakpoints that were set in the calling processing unit can also be processed here.
For further information on special breakpoints, refer to:
Breakpoints at Statements
Breakpoints at Subroutines
Breakpoints at Function Module Calls
Breakpoints at Methods
Breakpoints at System Exceptions
h2 page break h2
WINDOW TYPES
When defining a layout set window, you must select a window type for the window. You can choose between three types:
Constant windows (CONST)
Variable windows (VAR)
Main windows (MAIN)
CONSTANT WINDOW
A window of type CONST has the same contents and size on all layout set pages, on which a corresponding page window is defined. This allows the processing of the window contents to be optimized internally.
Page windows whose allocated window is of type CONST must have the same size throughout the layout set. If a window of type CONST is full, all remaining text the application program wants to output in this window, is lost. Constant windows do not trigger a page break. In other words: all text exceeding the window size is simply truncated.
VARIABLE WINDOW
The contents of variable windows is processed again for each page, on which the window appears. The system outputs only as much text as fits into the window. Text exceeding the window size is truncated; the system does not trigger a page break. Unlike constant windows, the page windows declared as variable windows may have different sizes on different layout set pages.
As far as the processing of the window contents is concerned, the system currently treats constant and variable windows alike. The only difference is that constant windows have the same size throughout the layout set.
MAIN WINDOW
Each layout set must have one window of type MAIN. Such a window is called the main window of the layout set. For SAPscript layout sets, the main window has a central meaning:
It controls the page break.
It contains the text body that may cover several pages.
It allows to fix text elements at the upper and lower margins of the allocated page window (for example, for column headings).
As soon as a window of type MAIN is full, SAPscript automatically triggers a page break and continues to output the remaining text in the main window of the subsequent page. Page windows of type MAIN have the same width throughout the layout set. The SAPscript composer thus avoids reformatting of the text after each page break.
If a page does not have a main window, the system implicitly processes all other windows of the page and continues with the subsequent page. This page must not call itself as subsequent page (recursive call), since this would produce an endless loop. In such a case, SAPscript terminates the output after three subsequent pages.
HOW THE COMPOSER WORKS
The composer or layout set processor is the central formatting module for the print output. It prepares the texts for the different output devices by using the allocated styles or layout sets.
Processing a layout set happens in a certain order. You must know some facts concerning the different window types, the setting of subsequent pages, or the dynamic control from within the print program.
Page control in layout sets
Define subsequent page statically
Define subsequent page dynamically
Format a layout set page
PAGE CONTROL IN LAYOUT SETS
SAPscript automatically triggers a page break as soon as the main window of one page is full. To be able to execute the page break, the system must know on which subsequent page to continue outputting the text. You can specify the subsequent page either statically when defining the layout set, or you can set the subsequent page dynamically during layout set output.
If the subsequent page is not specified, SAPscript automatically terminates printing, thereby ignoring any other output statements of the application program.
DEFINE SUBSEQUENT PAGE STATICALLY
You define the subsequent page statically with the layout set maintenance transaction. First, specify the start page in the layout set header. The system automatically calls this page whenever the layout set is started. With this page, or, more correctly, with the page window of this page, the text output starts. For each page, specify the subsequent page in the page definition. After a page break, the system continues text output on the subsequent page defined for the last page. By specifying start page and subsequent pages, you can define a page sequence.
DEFINE SUBSEQUENT PAGE DYNAMICALLY
The page sequence set in the layout set definition can be changed by the application program dynamically at runtime. If you want the layout set to start with a page other than the one defined in the layout set header, specify the desired start page using the parameter STARTPAGE when you call the function module START_FORM. However, this new start page is valid only for the current call of the function module.
If you want to break to a subsequent page other than the one specified in the page definition, use the control statement NEW-PAGE to set the name of the new page.
NEW-PAGE .
NEW-PAGE ends the output on the current page. The new subsequent page is only valid for the current call of the control statement. You can either include the control statement explicitly into the text of a text element or pass it to the layout set output using the function module CONTROL_FORM.
FORMAT LAYOUT SET PAGE
The process of formatting the output is controlled by the text contents in the BODY area of the main window. If the main window is completely filled, or if the control statement NEW-PAGE appears in the main window, the system executes a page break. Only at this point in time the system formats the contents of the windows of the other types and replaces the variables with the current values.
For each other window, the system first outputs the default text element, if it exists. Then it processes and formats the list of the active text elements of this window, which you set using the function module WRITE_FORM with the parameter FUNCTION (SET, APPEND, DELETE). Any text that does not fit into the page window is truncated.
As a consequence to this processing order of the composer, the reservation of space for the TOP and BOTTOM areas must be made beforehand. If the BODY area of the main window already contains text, a new text output to the TOP area does not appear on the current page but on the subsequent page in the TOP area. The same applies for the BOTTOM area. If the BODY area is filled to such an extend that the new BOTTOM text no longer fits into the current main window, this text appears on the subsequent page in the BOTTOM area.
A frequent error in application programs is that for the subsequent page (for example, NEXT) of a layout set no main window is defined. If the formatted text of the previous page did not fit into the corresponding main window , the composer searches the subsequent pages for a main window to output the text remainder. However, if the subsequent page of NEXT is NEXT again, the composer encounters an endless loop.
To be able to create correct page breaks in longer text, you should define a main window on each layout set page.
LAYOUT SET CONTROL
To output SAPscript layout sets, in the print program you must always start the output with OPEN_FORM and end it with CLOSE_FORM. The function module OPEN_FORM initializes the SAPscript composer and opens the specified layout set for subsequent output. The system combines all output for this layout set up to the CLOSE_FORM to one print request. If CLOSE_FORM is missing, nothing will be printed.
To output data in a layout set, you must use the SAPscript function modules WRITE_FORM, WRITE_FORM_LINES, and CONTROL_FORM. You can use these function modules any number of times in any order between opening and closing a layout set.
You cannot use the ABAP/4 statement WRITE to write output to a SAPscript layout set.
Several print requests
Start a layout set again
Switch layout sets
Find layout sets
SEVERAL PRINT REQUESTS
Within one transaction, you can open and close several layout sets using OPEN_FORM and CLOSE_FORM, however not simultaneously. You can use parameters in the OPEN_FORM to control whether the output is stored in the same print request. But also the SAP spool decides, depending on several plausibility checks, whether new output is appended to an existing print request or whether to create a new print request anyway.
CALL FUNCTION 'OPEN_FORM'
CALL FUNCTION 'CLOSE_FORM'
CALL FUNCTION 'OPEN_FORM'
CALL FUNCTION 'CLOSE_FORM'
You cannot combine ABAP/4 list output and SAPscript output in one print request.
START A LAYOUT SET AGAIN
Usually a print program does not print only one urging letter or one account statement, but several layout sets for different customers. To have the output for each customer begin with the start page of the layout set, you must start the current layout set again and again.
To start a layout set again, you must first end the current layout set and then open the layout set again. Within one print request, first call the function module END_FORM. It executes the final processing for the current layout set. Then start the layout set again using START_FORM. Output then begins again on the start page of the desired layout set.
CALL FUNCTION 'OPEN_FORM'
CALL FUNCTION 'START_FORM'
CALL FUNCTION 'END_FORM'
CALL FUNCTION 'START_FORM'
CALL FUNCTION 'END_FORM'
CALL FUNCTION CLOSE_FORM
If you use START_FORM and END_FORM, you must not specify a layout set for OPEN_FORM. However, in this case you can use the SAPscript output functions only after opening a layout set with START_FORM.

I can't find the "on my mac"folder in mail.

I can't find the "on my mac" folder in email. I created all my folders there and now can only find the emails if I search for them, but still don't see the folders. There were on the left side under my email accounts before I had to convert to ICloud. Can anyone help me find them?

Thank you of the quick reply and I kind of now have more info.
Since posting my question I "exported" the mailbox and voila, 2.6GB of info. So I think I have some solution.
"Are you desiring to Archive mail older than six months and remove that from Mail?" Not from Mail, but the iCloud, but when I did remove from icloud, I want to make another back up, even though I have time machine. I want to basically burn a DVD or put old email on other storage media.
"With a better understanding of your goal -- I can help you to a solution." Okay great, appreciate it! I hope I made/make sense.
"If you haven't done a Rebuild lately, I'd highly recommend you start there:" Ummm I've never rebuild.... so I also wanted to back up the data before I rebuild I think, right? I have no other copy, these emails were removed from the iCloud, and put in a mail folder on my mac (which I can't find the mailbox (mbox) on the mac, user name--->documents---> mail folder---> there is no corresponding mbox that I just created, this folder/get info says circa 2012), so the mail on my mac is not copied from iCloud. Technically I do have the time machine backup.... but you never know if that gets corrupted.
So my thought prior to rebuild is to export, as a back up, then rebuild? As to mailbox naming, since I have no idea where the corresponding folders are on my mac, exporting first, might be best option. If I rebuild, will that break or possibly lose data?
Thoughts?
Andy

Where can I find the download for Mac OSX Server Mountain Lion ?

Where can I find the download for Mac OSX Server Mountain Lion ?

On the App Store. Search for it:

I have a HP Laserjet P1102w printer hooked up to the USB port of my Airport Extreme. I'm able to print to the printer wirelessly from my MacBook Pro. My iPad (2nd gen) can't find the printer. What do I need to do?

My iPad is on the same network as the Airport Extreme. The HP printer is on the list of Airprint printers but I'm not using it as a wireless printer, per se, as it's hooked up to the USB port on the Airport Extreme.
I installed the HP ePrint app on my iPad. Unfortunately, the app could not find the printer either.
As mentioned earlier, I'm able to print wirelessly to the HP printer via my MacBook Pro.

ApplePearApple wrote:
Since I'm able to print to the HP printer from my MacBook Pro using this configuration, shouldn't I be able to print to the printer from my iPad, especially when all of the devices are on/using the same network?
Not necessarily. AirPrint uses a protocol separate from the communication protocol used for the Extreme's USB port. The HP printer may disable AirPrint when its USB port connected to a valid device, which is my reason for recommending you use it wirelessly.
From AirPrint Basics:
AirPrint printers connected using Bluetooth or shared through a USB port of a Mac, PC, AirPort Base Station, or Time Capsule are not supported.
AirPrint printers connected by Ethernet are supported in OS X.
You may get more competent assistance from HP. See this HP support forum topic: iPhone & iPad can't Airprint to p1102w LaserJet
HP's Mac support has always been miserable though. I have been much happier since I abandoned HP and started buying Brother printers. They just work.

Should I be able to use a Lexmark Pro 205 wireless printer from my iPad 1? My iPad can't find the printer. Iveinstalled the Lexprint app on iPad and downloaded the Lexmark Listener on desktop computer. Still can't print from iPad.

Should I be able to use a Lexmark Pro 205 wireless 3 in 1 printer with iPad 1? I have installed the LexPrint app on iPad, downloaded the Lexmark Listener on desktop computer but still can't print from iPad. My iPad cannot find the printer. But I can print from desktop without USB cable. I upgraded the system on my iPad sometime ago. Suggestions??

Here is the list of AirPrint printers, and you particular printer is not on it. So that means you will need to use the Lexmark app, and print through your computer.
There is a Lexmark guy that hangs around these forums who may chime in with a response as well.
http://support.apple.com/kb/ht4356

Mx922 not working after ink changed. now computer can't find the printer! Help!

Computer said the ink was low. Changed the ink when it finally stopped because of an insufficent amount of ink. Now the computer can't detect the printer, let alone the ink change! I have read some other posts and tried to reset the drivers, that didn't work either. Now I can't even reinstall the drivers because the computer can't detect the printer. The printer is on and says that it's connected to the wireless network. It says my only other option is to connect via the USB, well Canon does not provide this model with a USB cord. So what now I have to go out and get a USB cord so that I can use my EXPENSIVE printer! That is why I paid more, so I wouldn't have to use wires!
Please if anyone has any solutions that I have overlooked please tell me! I really need to print for work.

I had a similar issue with my new Macbook Air. I ended up going and finding the bluetooth preferences (/Library/Preferences) and deleting them. Then I restarted. This time around it could see the printer.

Have installed my 7200 all in one on my network, however my new hp laptop can not find the printer

I have a 7200 printer installed in my network, however my new HP laptop can not find it. CD will not work with windows 7, download from HP site did not help. have also tried using IP address to find the printer to no avail ?

There are some Updates on this page. Have you tried them?
Also, download and run this utility: http://h20180.www2.hp.com/apps/Nav?h_pagetype=s-926&h_lang=en&h_client=s-h-e17-1&h_keyword=dg-NDU&ju...
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

6280 All-in-One printer - changing from USB to Ethernet connection - error - can't find the printer

I am trying to reinstall my C6280 All-in-One printer from the product CD - my original installation was for a USB connection, I would now like to reinstall to an Ethernet connection for use on our wireless nework. I have gone through the HP -Installing the Product Software in Windows XP for a Wired (Ethernet) Network Connection - instructions but keep getting the error message - Can't locate the Printer. I have connected the ethernet cable in the ethernet port of the computer and the router (Airlink 101). Any suggestions on what I might be doing wrong?
This question was solved.
View Solution.

Hi,
You can use the following link to setup the printer over a wired n/w.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01708573&tmp_task=setupCategory&lc=en&dlc=en&cc...
Just to confirm..Make sure that you connect the "Printer and Router using the ethernet cable"
To make sure that your printer is found during the installation, after connecting the ethernet cable, make sure that your printer is getting a valid IP address.
Setup Menu--Network--View Settings--Display Wired Summary.
Although I am an HP employee, I am speaking for myself and not for HP.

How to resume partial download of adobe CS6,can't find the file on mac

hi ,
i was downloading adobce cs6 purchased yesterday but could only download 4gb out of 4.8gb. when i am again trying to resume the same download i cant find the file on mac in downloads folder. dont want to download all over again. Any suggestions
regards
amit dave

The problem of tracks becoming de-linked between iTunes and the music files in your iTunes music folder happens for different reasons - this seems to come up fairly commonly in this forum.
The solution can be to locate each song in the iTunes library, as you mentioned - or, but wait, before I get to that...
trouble finding the original track in your iTunes music folder? maybe look for it under compilations, or if not using the 'group compilations preference' then look in the folder under the songs artist name, but what song artist name iTunes uses depends on what you have in the metedata tag spot for album artist or song artist. Any varyation in artist name spelling, in the menu item 'get info' metadata for any selected individual track will cause iTunes to create that as a separate artist folder in the library, even names like 'various' or any difference at all (even the word 'the' can change where in your iTunes music folder a track gets placed by iTunes). You can try to use the finder function of find file (finder munu item outside of iTunes) to locate hard to find items.
Back to how to re-link any de-linked tracks .
There may be scripts that can help re-link de-linked music files - or, at least provide you a list of such files, Scripts are easy to install and use...
at Dougs Scripts, there is one called iTunes Track CPR that might work
http://dougscripts.com/itunes/scripts/ss.php?sp=itunestrackcpr
or, if you just want a list of de-linked tracks, go to
http://dougscripts.com/itunes/
and find the script called List MIA's, this will create a text file listing all de-linked tracks
if you review the thread at
https://discussions.apple.com/thread/3633708
also the thread at
https://discussions.apple.com/message/17513078#17513078
you may find more insight into dealing with this kind of issue there, although some of that thread may not apply to your case, aspects of it might help.
Good luck.

Apps can't find the printer

my wife's ibook was set up for her at the school where she teaches. She was designated as a user, and the tech director was the administrator. But he's now left the school, and the new guy has no knowledge about macs. Last week the computer crashed while she was working in Mail. Somehow, that crash deeply affected administrator and user access including keychain access, printers, and the Microsoft user database.
I did my best to repair the damage, changing her status to administrator, rebuilding the database, and now most things seem to work OK. I deleted the former administrator, and a test user, using the Accounts preference.
One thing i still can't fix is printing. She uses two printers at work, and one at home. Testing on the home printer, the Epson utility works just fine to check ink levels and print a test page. But I have not yet been able to print from any application like Word or Safari. I have tried placing the print driver in two or three different locations simultaneously, but these apps can not find that driver. Personally, I am now seriously wondering if there's a virus in her system.
Before I do a fresh install of Tiger, I thought I'd ask here if I am missing some obvious solution. Any help is appreciated.
ibook 800 mb (?) Mac OS X (10.4.7)
Dual 1.8 G5 and G4 powerbook

Hi Jim,
There's an Apple article that has helped other Epson ownsers. Have a look at this article (http://docs.info.apple.com/article.html?artnum=301631) to see if this is the issue.
If it doesn't help, can you explain what happens when you try to print. Does the printer icon appear in the dock? If you open the printer spooler, does it give some information about the job you have just attempted to print?
Also, have a look at the Console application (in Utilities) and open the file /var/log/cups/error_log. This will give some insight as to what is going wrong. It may still be a permissions issue...
Regards,
Paul

Quark Xpress Passport can't find the printer in Mac OS 9

Similar Messages

Maybe you are looking for