Question about 4500X VSS management port

I have two standalone 4500X switches that I'm planning to convert to VSS. If I cable the management port on both switches to a management cloud, which management port should I put the management IP address? Is it the port on the active switch? if the active switch failed, would the management port on the standby switch take over the management IP?
The management port is in VRF mgmtVrf. Should I create a default route for the VRF such as "ip route vrf mgmtvrf 0.0.0.0 0.0.0.0 ....." to point to its default gateway IP?
Thanks

When you convert the chassis to VSS, only the management interfaces (FastEthernet1) for switch-1 (active) will be visible in the config.  So you want to cable both management interfaces to your management cloud, but you only apply the IP to the active switch.
The management port is in VRF mgmtVrf. Should I create a default route for the VRF such as "ip route vrf mgmtvrf 0.0.0.0 0.0.0.0 ....." to point to its default gateway IP?
Correct, you need a default route in that mgmt vrf pointing to the gateway.
HTH

Similar Messages

  • Question about Quality Gate Management

    Hi Solman profis,
    I have questions about the transport requests in QGM.
    My Solution Manager is 7.1.
    I have a Solman project, in which I activated QGM and created a Change and created two transport requests (one workbench, one customizing) attached to it, .
    I'm little bit confused by the concept.
    My questions are:
    1. Why I cannot see the transport requests that I created previously in the DEV system manually? If it's normal, for which reason is this designed like this? If it's not normal, how can I configure to see those requests?
    2. What is the difference between the Change here in QGM and the Change in ChaRM?
    3. In practice, how should the transport requests be created? By the developer in DEV systems, or by the responsibles in Solution Manager Workbench (Change Management Workbench)?
    Thanks a lot!
    Edited by: Charlie Red on Feb 13, 2012 12:08 PM
    Edited by: Charlie Red on Feb 13, 2012 12:09 PM

    For the 3rd question, I think TRs should be created in Change Management Workcenter, is it the correct process?
    For the other questions, can somebody give some input?

  • A question about the IE management of session id

    Hi, guys! I have a question about the IE browser management of session id.
    As we know, firefox browser will use cookie to record session id, so if we delete the cookie files then the client can't find target session.
    But it's not the same as IE browser.I found I already can find target session after I delete the cookies.
    Then I think maybe IE browser use URL rewrite mechanism(GET request) and hidden text mechanism(POST request), but I'm not sure!
    Or maybe IE browser use current IE window process's cache to record the session id?
    Please help me, thank you very much in advance!
    I'm Chinese, my English is so bad, please understand, thanks.

    Thank you for your answer, but I still have a question.
    Can you tell me how your deleting cookies works? I just use IE browser tools->Internet Options->Delete Cookies to delete my cookie, but the session still can be retrieved! Just like you said, the session id is kept in the memory.
    But if I use firefox to do the same operations, the session will can't be retrieved.Does that mean firefox not only delete cookies' files but also delete them in the memory.
    Can I use IE browser to do the same effect as firefox browser? And how to do? Thank you.

  • 3560 and 3750 - Question about 10/100/1000 ports

    I am researching several Cisco products to recommend to a customer. I was wondering if the 10/100/1000 ports at a 3560 switch, will provide gigabit bandwith on each port or if the bandwidth is shared among several ports. The latter is how a 48 port 10/100/1000 line card would behave on a Cisco 4500 when, depending on the card, the gigabit bandwidth will be shared among 4 or 6 ports at a time.
    What about 10/100/1000 ports on a 3750?
    Thanks

    The new Catalyst switches/modules such as the Catalyst 6500/6000, 4500/4000, 3550, and 2950 support 10/100/1000 Mbps negotiated Ethernet interfaces or ports. These ports work on 10Mbps, 100Mbps, or 1000 Mbps speed based on their connection to the other end. These 10/100/1000Mbps ports can be configured for speed and duplex negotiation in the same way as 10/100 Mbps ports on CatOS or Cisco IOS Software-based switches. Therefore, the configurations given in this document for 10/100Mbps port negotiation applies to 10/100/1000Mbps ports as well.
    http://www.cisco.com/en/US/tech/tk389/tk214/technologies_tech_note09186a0080094781.shtml

  • K8N Neo2 question about overclocking and sata ports 1 & 2

    Hi guys,
    I know that when overclocking, sata ports 1 & 2 cannot be locked like sata ports 3 & 4, and therefore hard drives on ports 1 & 2 can be corrupted.  However, I would like to understand what is failing when the unlocked ports get overclocked.  Is it the motherboard that makes mistakes or is it the drive?  Since the ports on the K8N Neo2 are Sata 150 (correct me if i'm wrong), would buying a sata 300 drive be able to survive overclocking?  Also, I would like to know the effect of overclocked sata ports on dvd burners as opposed to hard drives.  I am looking to buy two new Dvd drives/burners for this board and I would like to avoid buying IDE again.
    So, can anyone answer the above questions in detail?
    Thanks,
    Steven

    Quote from: SteveH647 on 24-September-09, 04:39:34
    But is it the HDD itself that fails at the higher frequency?  Or is it the HDD controller on the motherboard that fails?  What about DVD drives?  And what if the HDD is SATA 300 instead of SATA 150?
    Quote
    But is it the HDD itself that fails at the higher frequency?
    Yes.
    Quote
    Or is it the HDD controller on the motherboard that fails?
    No
    Quote
    What about DVD drives?
    Can't tell you, haven't maked such experiments.
    Quote
    And what if the HDD is SATA 300 instead of SATA 150?
    It will not change anything.

  • Newbe question about SG300-20 dropping port to Router

    Hello to you all
    Today I received my new SG 300-20 managed switch to replace an unmanaged switch with some faulty ports.
    I want to use it in a a combined Home / Small Office environment. It is my first purchase and use of a managed switch so am still new at it.
    I come from an IT-background but more from the software side than the hardware side of things, but I feel comfortable with hardware and network things.
    I was planning to start using the switch in its most basic configuration first and gradually start learning the finer details of its configuration, with the ultimate purpose of setting up several VLANs for business, private use and media playing and to do some IPv6 experimenting.
    All my attached devices are Gigabit network capable.
    The issue is when connecting the cable to my router (an ISP provided FritzBox 7340 (an ISP version comparable to 7390) which is IPv6 capable) the SG 300-20 keeps dropping the port.
    The log show the following messages repeated 3 times:
    2147483597   2011-Mar-18 17:08:53 Warning   %LINK-W-Down: g8 
    2147483598   2011-Mar-18 17:08:50 Warning   %STP-W-PORTSTATUS: g8: STP status Forwarding 
    2147483599   2011-Mar-18 17:08:46 Informational   %LINK-I-Up: g8
    It doesn't matter which port I use the same thing happens each time.
    All other devices connected to the SG 300-20 just work fine.
    When I connect the router to my old switch it also just works fine.
    When I connect my old switch with router attached to the SG 300-20 it works fine and the DHCP on my router will provide the SG 300-20 with an IP-address.
    I just can't connect the router directly to the SG 300-20.
    I'm a bit at a loss of where to look for a solution.
    As I said all is still in default settings.
    Can anybody point my to a solution or way of finding out what is the problem why the port is being dropped?
    Thank you
    Alwin

    This is a gateway device.....also known as a modem/router. It combines the functions of a separate modem and router in one package.
    The Q1000 is the main router on your network, so any port forwarding (Apple calls it Port Mapping) must be done on the ActionTec device.
    The Time Capsule is in Bridge Mode. In this type of setting, all ports are automatically already open. So, there is no need to "open" a port that is already "open".
    The Time Capsule will simply pass through any information that it receives from the ActionTec gateway to other connected devices on the network.

  • Question about 6 Way Firewire Port and Ex. HD's

    I recently bought the Belkin 6-Port Firewire adapter. Right now I have two external HD's ( 200 GB and 300 GB ),and my iSight connected. I was wondering if it was safe to have my two HD's always connected? I've been having issues with my screen turning dim and not coming back to normal until I restart. I reset the PRAM and still after using my iMac for awhile the screen turns dim, like as if were about to go to sleep, but when I try to brighten it, it stays the same brightness?

    Assuming the harddrives have their own power supply the issue us unlikely to be related. Its unlikely to be related either way.
    Are you sure you are not losing connection to the keyboard so when you try to brighten it takes a while for the keyboard to reactivate, plenty of people have had issues with the keyboard.
    Also you can switch off the totally pointless slight dimming thing in the energy saver part of system prefs
    Intel iMac 20inch, 14inch Book   Mac OS X (10.4.5)   Maxed up baby

  • Questions about Deployment Operations Manager 2012 R2

    Hi Folks
    Questions: I have one infrastructure with Operations Manager 2012 R2, two Management Server.
    Now, I'm trying install feature operations manager reporting in SQL Server.
    added the OMDRA and OMDWWA accounts as a local administrator of the SQL server.
    I'm using media installation Operations Manager 2012 R2, but I'm received erros, any idea? Or I need using media installation Operations Manager 2012 SP1?
    Thanks
    Wilsterman Fernandes

    Hi There,
    I had seen a similar issue here. The error log has a point mentioning " ApplyUpdates: Unable to load QFE file."
    I saw this error on this below thread as well.
    https://social.technet.microsoft.com/Forums/en-US/a10ce69e-2584-4a4d-86b9-64ee8c5bf85d/reporting-services-installation-failing?forum=operationsmanagerreporting
    He said he fully re installed the whole setup and it solved the issue.
    But i understand that is quiet difficult and complicated to do.
    =================================================
    I would suggest you check the permissions again
    1.Does your data reader and writer account have SQL permissions i.e sysadmin permissions ?
    2.Also is your SQL server in the same AD Domain or is it in a different domain ?
    3.Is the SQL Server scale of deployment joined ?
    4. Did you look in the ops manager event logs ? Can you check and post them here plz.
    5. Is the operationsmanager DB and warehouse DB as well hosted on the same SQL server where you are trying to install reporting.
    Gautam.75801

  • Question about how Oracle manages Redo Log Files

    Good morning,
    Assuming a configuration that consists of 2 redo log groups (Group A and B), each group consisting of 2 disks (Disks A1 & A2 for Group A and Disks B1 and B2 for group B). Further, let's assume that each redo log file resides by itself in a disk storage device and that the device is dedicated to it. Therefore in the above scenario, there are 4 disks, one for each redo log file and, each disk contains nothing else other than a redo log file. Furthermore, let's assume that the database is in ARCHIVELOG mode and that the archive files are stored on yet another different set of devices.
    sort of graphically:
        GROUP A             GROUP B
          A1                  B1
          A2                  B2The question is: When the disks that comprise Group A are filled and Oracle switches to the disks in Group B, can the disks in Group A be taken offline, maybe even physically removed from the system if necessary, without affecting the proper operation of the database ? Can the Archiver process be temporarily delayed until the disks (that were removed) are brought back online or is the DBA forced to wait until the Archiver process has finished creating a copy of the redo log file into the archive ?
    Thank you for your help,
    John.

    Hello,
    Dropping Log Groups
    To drop an online redo log group, you must have the ALTER DATABASE system privilege. Before dropping an online redo log group, consider the following restrictions and precautions:
    * An instance requires at least two groups of online redo log files, regardless of the number of members in the groups. (A group is one or more members.)
    * You can drop an online redo log group only if it is inactive. If you need to drop the current group, first force a log switch to occur.
    * Make sure an online redo log group is archived (if archiving is enabled) before dropping it. To see whether this has happened, use the V$LOG view.
    SELECT GROUP#, ARCHIVED, STATUS FROM V$LOG;
    GROUP# ARC STATUS
    1 YES ACTIVE
    2 NO CURRENT
    3 YES INACTIVE
    4 YES INACTIVE
    Drop an online redo log group with the SQL statement ALTER DATABASE with the DROP LOGFILE clause.
    The following statement drops redo log group number 3:
    ALTER DATABASE DROP LOGFILE GROUP 3;
    When an online redo log group is dropped from the database, and you are not using the Oracle Managed Files feature, the operating system files are not deleted from disk. Rather, the control files of the associated database are updated to drop the members of the group from the database structure. After dropping an online redo log group, make sure that the drop completed successfully, and then use the appropriate operating system command to delete the dropped online redo log files.
    When using Oracle-managed files, the cleanup of operating systems files is done automatically for you.
    Your Database wont be affected as you can operate with 2 redo log files in each group as The minimum number of redo log files required in a database is two because the LGWR (log writer) process writes to the redo log files in a circular manner. so the process will hang becuase you are having 2 only groups if you want to remove 1 add a third one and make it the current group then remove the one you want to be offline.
    Please refer to:
    http://download.oracle.com/docs/cd/B10500_01/server.920/a96521/onlineredo.htm#7438
    Kind regards
    Mohamed
    Oracle DBA

  • SBS 2003 migration to SBS 2011 - Question about SQL Server Management Studio

    I am preparing to do a migration from SBS2003 to SBS2011. In the migration instructions it tells me to install SQL Server Management Studio Express Service
    Pack 2. I have SQL Server Management Studio (NOT EXPRESS) installed and it is on SP2. 
    Do I need to also install the express version to do the migration?
    Thanks in advance,
    Dan

    Hi,
    Thanks for your posting.
    I think you don't need to install the express version.
    Regards.
    Vivian Wang

  • Quick Question about SAP solution manager

    Hi,
    How to Edit or Delete or create New Entry in "Landscape Components"
    I having problem in Solution Manager 4.0
    Tr: SMSY goto Landscape Components --> Systems --> SAP R/3 --> NQA --> R/3 Server
    In CLIENT Tab entry listed blow:-
    Client: 250
    Name: NQA Server
    Role: Production
    Logical system: NQACLNT250
    RFC Read Access: SM_NQACLNT250_READ
    RFC Change Manager: SM_NQACLNT250_TMW
    Trusted system RFC: SM_NQACLNT250_TRUSTED
    RFC for solution Manager: SM_NQACLNT250_TRUSTED
    My qestion is when I highlight entry and click on RFC pushbotton there is no such as I can change or Edit entry or I can't delete that Row ?
    How can I do that please advised
    Thanks

    Hi there,
    If I follow what you're saying, you want to delete one of your clients from your system in txn SMSY.  Per the SAP online help (see below), you need to switch to "manual" maintenance mode, as it is assumed that your system's data was populated automatically.  See the online help below and try what it suggests. Note: I'm on SOLMAN 4.0, SP15.  In SMSY there is no "Landscape Components ® Other Object" option.  It is actually the button just to the left of the pencil (Change) button whose text says "Other Object..".  Click that button, then click the System radio button, then put in your system's system name (ie Q01), then click the button on that pop-up that looks like an unlocked lock, then click Yes on the pop-up after that, then click on the greencheck button(s) until you're back in SMSY.  You may have to re-click on your "R/3 Server" link to get back to the client tab/screen.  Make sure you go back into Change mode and then your "delete" button will be available.
    FYI - just below here is the online help for what I described above. Below that I've included comments of what I did when I did this myself.
    Manual Data Source Maintenance
    Use
    You cannot edit all data manually in servers, databases and systems which were determined automatically. You can set the data source to manual maintenance, to be able to edit all data in this landscape element manually.
    You should only set the data source to manual maintenance if the automatically captured description does not match the actual definiton of the landscape component. This can, for example, be the case if a system temporarily has an additional server, which is recognized by the automatic data capture, but should not be in the system description because it is only temporary.
    Prerequisite
    You are in the Solution Manager System Landscape (SMSY).
    Procedure
           1.      Choose Landscape Components ® Other Object, or
           2.      Choose the landscape component from the possible entries help, or enter the name of the landscape component.
           3.      Choose the Set Data Source to Manual Input pushbutton.
           4.      Confirm the confirmation prompt.
    END of ONLINE HELP section
    Below is the text from the pop-up msg after I clicked on the button (for my Q01 system) in the "Select Other Object" pop-up called "Set Data Source to Manual Input".  That button looks like a unlocked lock symbol.
    Switch object to manual maintenance
    You switch an object to manual maintenance to be
    able to edit the object description determined
    by the system, manually.
    You should only do this if the automatically
    determined description does not match the
    definiton of the object. This can, for example,
    be the case if a system temporarily has an
    additional server which is recognized by the
    automatic data capture, but should not be in the
    system description, because it is only
    temporary.
    Do not delete any required parts of the object
    definition, and keep the definition of the
    object consistent.
    Switch Q01 to Manual Entry?

  • Questions about the single audio port of my Macbook Pro 10.8.2

    So, I need to simultaneously have one audio output and an audio input. I noticed my macbook has one audio jack (with the icon of headphones) and I was wondering what kind of potential it has? Or, what my options are? This is mostly for recording music, so I can have headphones in the output and my synth in the input.
    I have a cable where it doubles the holes of the headphones jack (I know for sure it's an output, but can it be used as input as well?), it's the 1/8" jack that plugs into your computer and the other end is just two "headphones" holes. So.. I can physically plug in my synth and headphones, and when my synth's "local" is off, and I play the keyboard - i hear nothing through my headphones. When the "loca" is on, I hear myself playing through the headphones. Therefore, the sound of the synth has to be going through the audio line as input and coming out as output or something... So I would think that it does double as inout ad output but I really don't know. But... in Logic I can't record anything either way. So, I don't know if I'm messing up or if the macbooks jacks are just being used incorrectly... There's a lot of variables to this problem ):

    vietna wrote:
    So the USB 3.0 will definitely work as an input source if I get a USB/audio cable? Can the USB ports work as both in and out lines? Also, I have a midi USB interface hooked up... it won't like override or do anything weird with that will it?
    I did not say that, I said "Use a USB interface"
    There are thousands of them out there, and they will provide higher quality than the 1/8" analog connection.
    Look at Lexicon, M-Audio, Tascam etc, look for the facilities you want (2ch/4ch/morech, mic/line inputs etc)

  • MOVED: K8N Neo2 question about overclocking and sata ports 1 & 2

    This topic has been moved to Overclockers & Modding Corner.
    https://forum-en.msi.com/index.php?topic=130785.0

    Quote from: SteveH647 on 24-September-09, 04:39:34
    But is it the HDD itself that fails at the higher frequency?  Or is it the HDD controller on the motherboard that fails?  What about DVD drives?  And what if the HDD is SATA 300 instead of SATA 150?
    Quote
    But is it the HDD itself that fails at the higher frequency?
    Yes.
    Quote
    Or is it the HDD controller on the motherboard that fails?
    No
    Quote
    What about DVD drives?
    Can't tell you, haven't maked such experiments.
    Quote
    And what if the HDD is SATA 300 instead of SATA 150?
    It will not change anything.

  • Question about output the com port signal

    Dear all,
    I can successfully change the received signal from COM1 into ASCII, and I can use System.out.print to output the ASCII. However, I cannot output the received signal in the JTextField.
    Could anyone help me to solve this problem please?
    Thank you so much

    May I suggest the setText() method?

  • Information about SAP Strategy Management (SAP SM)

    Hello,
    I want to know where I can find information about SAP Strategy Management (SAP SM). This is an application that was bought from PILOT.
    Is it easy to customize like the SEM-CPM-BSC????
    Is it an addon in the BW or ECC????
    Is it all browser type application???
    Thank you in advance...
    Pablo Mortera.

    Greetings Pablo,
    Thanks for your interest in SAP Strategy Management (SSM). More information can be found on the BPX site for Corporate Performance Management.
    https://www.sdn.sap.com/irj/sdn/bpx-cpm
    On that page is a short demonstration of SSM. There are two other sections on that page -"Key Topics" and "Best Practices" have links for more information about Strategy Management.
    On the SAP.com global site, there is also information about Strategy Management, including white papers.
    http://www.sap.com/solutions/performancemanagement/strategy/index.epx
    Please review all this information and let me know if you have additional questions about SAP Strategy Management.
    Regards,
    Bob

Maybe you are looking for