Question about Airport Extreme, Cable Modems??

Help, I am new to wireless and I need some help with setup. I have tried to even register my new airport extreme and can't seem to get started on any of this. I understand much of the concepts, but the networking I am familiar with involve cables and routers, ethernet.
I have a cable modem with Comcast that is very old. I have a suspicion I may need to get a newer cable modem. What modems out there have had success so to speak, I also have a new quickey USB Tranceiver I am trying to get hooked up, which is suppossed to take care of a internal airport card???
Of course to start setting this up, I will be killing my internet connections so I can not look up forums for help. Anything I should do before I unplug and try to get ethernet signal from Modem to Airport?

Even though your cable modem is "very old", it may well work just fine with your new base station. I suggest you try it - and if it works, you'll have saved yourself some money.
Connect the modem and your base station. Then pull power to both for at least five minutes - longer if you are patient enough. Then plug the modem into power and wait a minute. Then plug the base station into power and wait a minute. If all goes well, your base station will show a solid green status light telling you it has successfully connected with Comcast's service.
Cable your Mac to one of the Base Station's LAN ports - and it should now have internet access.
My understanding is that the Quickey "Quicky USB Transceiver" is used to improve the range of a Mac that is already equipped with an Airport card.

Similar Messages

Few questions about Airport Extreme/Express

I have a few questions about Airport extreme/express:
1 Can you access hard drive trough express?
2 I have cable NOT wireless modem. What would be the best option (speed-wise) to connect to internet- connect modem to Extreme and access internet wirelessly from it? To connect modem to Extreme and imac?
3 How fast is read/ write from hard drive connected to Extreme?
4 How many hard drives can you connect to Extreme (or Express if that is possible)?
5 Can you remotely sync Ipod nano/ shuffle using Extreme?
I really hate wire clutter around my desk. What I intend to do is to connect hard drives and printer to Airport Extreme and access them remotely. That would leave empty desk:).
Thanks

1. You cannot connect a hard drive to the Airport Express USB port.
2. The speed of wireless networking is faster than the speed of most cable internet services. Therefore, you won't notice any difference in your internet connection speed between (a) a cabled connection directly between Mac and modem or (b) a wireless connection between Mac and base station and modem.
3. Apple has not published any specs on the speed of hard drive access for the Airport Extreme N Base Station. Several people have posted their own measurements (do a search in this discussion forum), and generally those results are not very good.
4. Apple has not placed a limit on the number of drives you can attach to the Airport Extreme N Base Station (with use of a hub). How many do you want to connect?
5. You cannot remotely sync an iPod using the Extreme Base Station.

A PC user's questions about Airport Extreme & Airport Express

Hi all,
I have a few questions regarding both the Airport Extreme AC and the Airport Express.
I am a PC user who is currently looking at replacing my Cisco Linksys EA4500(primary router) and my Linksys E2500(bridge router) due to the lack of regular firmware updates that Linksys fails to provide for their routers and the fact that I simply find Linksys products to be buggy.. Based on my research, Apple's Airport Extreme N and the AC versions have received excellent reviews on Amazon and I am considering purchasing both the Airport Extreme AC(to replace my Linksys EA4500) and the Airport Express(to replace my Linksys E2500).
Before I get to my questions, let me be frank in saying that I do not have a Mac(but intend to after my desktop dies) at this time but in my house we have two iPhone 4s's and one iPad 2 as far as Apple products are concerned. My computer network consists of my HP Windows 7 based desktop and HP Windows 7 laptop and I have a home ethernet in every room in the house . In addition, my den's ethernet connection is connected as Ethernet wall jack in which the connections include---->Ethernet switch------>Tivo---->Playstation 3/Xbox 360/Nintendo Wii/----->Samsung Smart TV---->Linksys E2500.
My questions are as follows:
1. Initial/Out of the box set up: Based on what I have read here, it is possible for a PC user to setup the Airport Extreme by downloading the Airport Extreme utility software from Apple. However I have been confused based on what I have read on Amazon in that some users report that the initial setup can only be done using a Mac. Would someone from this forum kindly clairify this for me? Can I set up the Airport Extreme with my network assuming that I have previously downloaded an installed Apple's Airport Extreme Utility for the PC?
2. Using the Airport Express as a wireless bridge: Currently my Linksys E2500 serves as my secondary router in my den in bridge mode. Can I set up an Airport Express as a wireless bridge assuming I was sucessfully in setting up my Airport Extreme? On Linksys products this is done by setting the router in bridge mode and assigning it a specific IP address within the bridge router's settings. So for example, my Linksys E2500 has a 192.168.1.1X IP address, can I do this with the Airport Extreme? Note the the intention here for the extra router in my den to provide additional wireless coverage due to the size of my home. I do not need it to provide me with the same wireless network name as my primary router, I only want to provide the back of my house with additional wireless coverage that a primary router will not provide.
3. Router Security and reliability: I would like the router that I purchase to include regular firmware updates beyond that of one year. Especially now that most modern routers have some sort of cloud set up, I wouldn't want to purchase a router today, only to find out that I wouldn't be able to update its firmware one year from now. With respect to Apple's routers, how often does Apple release firmware and typically speaking; how long will Apple support additional firmware releases for its products?
Thanks to anyone who reads and responds to my long post!

The one problem is Apple using their own automatic port opening system.. NAT-PMP which is fine for apple clients but will not work with almost anything else made which depends on UPNP ..
There are lots of hassles with PS3 and XBox live and anything that depends on standard automatic port opening for interactive internet connection.
Manually opening ports is possible but a pain.
eg
AirPort Extreme and xbox 360
https://discussions.apple.com/thread/5385065?tstart=0
I do agree with John Galt that the Apple products are well made and generally great.. they did have a bad capacitor failure issue in the Gen1 and Gen2 TC which he may have forgotten about.. I have repaired about 200 of the bludgers. And there was a dedicated site to pressure apple to fix them.. with 2500 recorded dead TC.
See http://timecapsuledead.org/
See
https://sites.google.com/site/lapastenague/a-deconstruction-of-routers-and-modem s/apple-time-capsule-repair
And some ongoing issues.. even post getting that fixed up.
https://sites.google.com/site/lapastenague/a-deconstruction-of-routers-and-modem s/apple-time-capsule-repair/new-issue-with-a1355-gen-3-tc
But the AEBS had external power supply so didn't add to the heat of built in HDD and power supply in a case too small without cooling. New ones seem to have learnt the lessons of the past in that the power supply is internal but they use a fan system to keep it cool.
See http://www.ifixit.com/Device/Apple_Time_Capsule for internal construction.. TC and AEBS are now identical except for the hard disk.
An option worth considering is using a router with third party source firmware.
You are then never cut off from great updated firmware.. and you can do amazingly more with the fuller setup that includes Telnet cli and extensive interface on the GUI.
Eg Gargoyle on a Netgear WNDR3800 or even cheaper TP-Link WDR3600 or WDR4300.
These offer full QoS, not in Apple products.
Full throttling controls, not in Apple products.
Quota, not in any other products in domestic market at all.
NAT-PMP and UPNP, not in Apple products.
VPN, not in Apple products.
Multiple VLAN, Multiple IP addressing, not in Apple producs.
SMTP, which Apple removed from all their new products.. no reason why.
Log access, which Apple removed from the new airport utility.. no reason why.
etc.
If for some reason that firmware doesn't suit.. you can flash over to DD-WRT, or OPENWRT.. etc. in other words you are never again beholden to the manufacturer who after the product is EOL is also end of support.

Random Questions about Airport Extreme Card

I have an early 2006 iMac with the built in Airport Extreme card, and so far I've managed to use it to share my ethernet internet connection with my Nintendo DS, Wii, PS3, Apple TV, etc.
But I have some random questions that I'm hoping some of you people can answer.
1. Does my Airport card support UPnP (or whatver the Mac equivelent is), and if so, how do I enable it?
2. With my old router I used to be able to type it's IP address into the address bar of my browser and access the settings for it. Anyway of doing this sort of thing to access the Airport's settings?
That's all I need to know really. Any help would be appreciated.
1.83 GHz Intel Core Duo, 2GB RAM Mac OS X (10.4.10)

Hi
UPnP is handled by your router/modem.
You cant get access to the airport extreme card it has no settings to my knowledge(apart from network prefs).
Tony

Voltage specs and international question about Airport Extreme (802.11n)

I'm about to travel to Korea to teach English for a year so I'm preparing all my electronic gear for the journey and I've come to a curious question involving the Airport Extreme with 802.11n.
First of all, I'm worried about voltage (Korea runs on 220v / 60Hz). For most hard drives (and Apple hardware in general it seems) the power supply is auto-switching 100-240v 50/60 Hz, but when I looked at the official specs for the Airport Extreme (hereafter AEBS) this info is conspicuously absent. The AEBS itself runs on 12V DC power, which is listed in the specs, but the input tolerance for the AC adapter isn't mentioned. I checked the specs for the Time Capsule since the hardware is presumably very similar and it is explicitly 100-240v. Likewise the replacement power supply available from Apple is listed as 100-240v, but since it is a replacement part I'm not sure if it is the exact same make as the adapter that ships with the AEBS in North America. If someone knows the definitive specs, I would appreciate an answer.
Secondly, when I tried searching the Korean Apple site (www.apple.co.kr) for specs on the Korean version of the AEBS to see if it was the same, I discovered that the Airport Extreme isn't available in Korea (although the Airport Express and Time Capsule). Does anyone know why this is? Is it possible the Airport Extreme doesn't comply with Korean wireless standards (I know the iPhone isn't being released in Korea because of laws about middleware that must be installed on cellular phones in Korea)? It seems safe given the availability of the Time Capsule in Korea, but does anyone have any specific knowledge about the Airport Extreme or Wi-fi regulations in Korea?
Sorry if this is a strange question, but I'd appreciate insight from the more experienced/advanced Apple users out there.
-Matt Tranquada

Thanks for the response. I guess what I would like to know is if I am closer to the newer 802.11n AE base station with my laptop, will it ignore the older base station and communicate directly with the stronger signal, or does it communicate with the weaker, more distant signal. Does the laptop automatically determine which base station has a stronger signal and choose it, or is it fixed which base station the laptop communicates with?

Airport Extreme , Router, Modem set up question: Extreme now flashing yello

Trying to help a disabled friend and my thinking is stuck
Friend has new Macbook, using it wirelessly. Setup which was fine until this week: Older cable modem needs a Wireless Router piggybacked onto it to accommodate wireless. Modem connected to Cable Ethernet hooks the router to the Modem. AirportE Extreme connected via Ethernet cable to the Router. Until this week, Airport showed the solid normal green. The disabled man " did something on his computer" - he cannot recall what he did - may have been a firmware upgrade message- and lost connectivity.
Last night I re-establshed connectivity but the Airport now flashes yellow and Airport Utility cannot find the Airport.
Despite that , the man has internet connection, Network Preference shows Green radio buttons for Internet and the Airport signal thingee in the menu bar shows all bars black.
My puzzle:
1) the Extreme flahing yellow and cannot be found
2) The network which is active, named Router is NOT the network which was active ( I set up things up initially months ago, have notes which indicate we had a different network operative in past)
3) I cannot use Manual set up.. that option remains grayed out
4) I tried to reset Airport Extreme to factory settings, but Holding a pen tip in the reset button for well over a minute did not seem to reset anything.
With all this, the man has internet connectivity! I saw it, tested it (went to website that could not have been in the cache, sent myself an email.. connections are patent but I do not know how.
Is it possible the gentleman's attempt to do the firmware update scrambled the Airport extreme?
Any thoughts what I might try?
I also asked the gentleman to call the ISP about an updated cable modem so we don't need to piggy back the linksys router to get wireless.

Directly connect a computer to one of the Extreme's LAN ports and open AirPort Utility. Does this allow AirPort Utility to find the Extreme?

Is a Happy Marriage Possible? New Airport Extreme & ADSL Modem/Router

Is a Happy Marriage Possible? New Airport Extreme & ADSL Modem/Router
1. I’m writing from a rural town in Southern Nepal, very close to India. I’m planning to create a new WI-FI network at a small monastery here. Ideally, we will have two parallel wireless networks: the first network produced by an ADSL router/modem and a second network produced by another router in “repeater” mode.
2. Earlier, someone suggested that, when I post a question, I should provide as many details as possible about the situation here. Forgive me if there is “too much information”. I have to make a trip to the US to buy new networking equipment, so I very much want to get this right. Once I return here, I’ll be pretty much stuck with whatever I get in the US.
3. The future routers will live next to each other in an office and could be linked by a cable (if this is the best route to go). We do not wish to “expand” the network (in the sense of making a larger WI-FI network), but rather wish to simply have two networks, hence one ADSL router/modem and one router with the “repeater” function (out-of-the-box without any jerry rigging). Both WI-FI signals need to travel approximately 100 (largely unobstructed) feet.
4. If my dreams come true, the second router would be an Apple Airport Extreme (AX). An Apple router would be ideal because my experience with Apple routers is happy: they are easy to set up, reliable, and secure. Moreover, we use Apple computers and iOS devices here (and the new AX has the “ac” thing which will be preferable as we replace old machines with new ones).
5. Yet, from reading posts and having my prior questions answered on this website, it may be that with an ADSL modem/router, all the ease and happiness of the Apple ecosystem is lost: while Apple routers seem to connect with each other easily, problems appear to arise when users try to inter-marry our non-Apple products with Apples.
6. Our current, super-crappy 2wire 2701hg-t (ADSL modem/router) covers the 100-foot distance without a problem when it is working and there is Ethernet flowing to us. Frequently, our connection is very bad, and I may be unfairly judging the 2wire 2701hg-t. But, based on user reviews on the America Amazon.com, the 2wire 2701hg-t is pretty terrible: first it is simply old and second, among other problems, it seems to have a poor quality power supply unit. I do observe that it frequently seems to be recycling from scratch as if it had turned off and restarted. In any case, we are replacing it since it may be about 4 or 5 years old.
7. In previous posts on this forum, “LaPastenague” responded to some of my earlier questions about AX and ADSL. Among other things, he pointed out that (1) line-attenuation may be contributing to our poor connection and (2) we must choose a modem/router that is suitable for “long lines.” I’ve looked at our current modem/router statistics page; however, there are no statistics for line-attenuation or noise. (As you will see below, my strategy is to get the “better” modem/router that is suitable for long lines.)
8. Concerning our ADSL service, these are the facts I’ve gleaned from looking at the current router’s configuration pages:
Connection Type: PPPoE
Currently, the router is configured to use WPA-PSK security.
Connection Speed: Incoming: 1024 kbps & Outgoing: 509 kbps
(The following information may be unimportant at this time.)
Broadband Link Diagnostics:
DSL Synchronization: UP
G.DMT Signal: UP
PVC Connection: UP
PPPoE Service: UP
PPP Authentication: UP
IP Connection: UP
DNS Communication: UP
9. The ISP (Nepal Telecom) doesn’t supply a modem/router; however, they do have a list of (at times ancient) hardware and hardware vendors:
http://www.ntc.net.np/internet/adsl/adsl_vendersConf.php
10. Concerning what equipment is available here, what I have observed is that generally the ADSL modem/routers for sale locally, and in the far-away capital Kathmandu, and in nearby India are often also available in the United States, but they are the cheaper, older models. I will have to buy the new equipment in the US this year. At a different institution nearby, they are using the TP-Link modem/router td-w89016 which they purchased locally, I believe.
11. Based in part on LaPastenague’s earlier advice, I want to buy the TP-LINK TD-W8980 N600 Wireless Dual Band Gigabit ADSL2+ Modem Router (2.4GHz 300Mbps+5Ghz 300Mbps, IPv6 Compatible). This appears to be the most popular ADSL device on Amazon now.
Will this modem/router work EASILY with the Airport Extreme in the manner I’ve described? That is, connecting the two with a cable and creating two WI-FI networks.
12. Also, is it generally correct that the best way to connect them is with an Ethernet cable: https://discussions.apple.com/message/23759755#23759755
13. In fact, does connecting them with a cable help alleviate some of the problems that can occur between the Apple device and the ADSL modem/router?
14. If this will work, what “mode” will the AX device be in (again, in order to have two separate networks with separate passwords)? I have heard of the “repeater”, “roaming” , and “bridge” modes.
15. Are there two levels of passwords which need to be considered? Of course, there is the network and network passwords which we create here and which will be different. But, does the Apple also have to have the ISP password like the principle ADSL modem/router?
16. To set this up, what information do I need from the ISP (e.g., passwords, IPs…)?
I think there are a lot of good reasons to use an AX router. Of course, if it is just going to be very cumbersome then, we would be loosing one of the best parts of using Apple products. So, whoever feels knowledgeable enough to reply to this post, please be sincere if you think it is better to avoid the Apple. Apple can rest assured that I will buy other things from them!
In that case, I’d likely buy a second TP-Link device to create a second network:
TL-Wa801NP [AP Mode Multi-SSID Mode AP Client Mode Repeater Mode (WDS / Universal) AP+ Bridge mode (point-to-point / point to Multi-point)].
Thank you in advance. Long live Apple!
Message was edited by: Jess1911

I am not sure if there are different interfaces but my 2wire does an excellent job with line info.
I get into this from browser.. using main IP.. in my case 10.0.0.138/MDC
In your case it should be whatever the IP of the 2wire is, followed by /mdc
Give it a try.
As you can see it shows vendor and loads of info about the line.
I rate it the best domestic modem for line info.
A good modem actually albeit a lousy router.
MDC is the diagnostics and Management Console.
3. The future routers will live next to each other in an office and could be linked by a cable (if this is the best route to go). We do not wish to “expand” the network (in the sense of making a larger WI-FI network), but rather wish to simply have two networks, hence one ADSL router/modem and one router with the “repeater” function (out-of-the-box without any jerry rigging). Both WI-FI signals need to travel approximately 100 (largely unobstructed) feet.
You are not repeating.. you are simply setting up two routers which are interconnected, so one is dependent on the other.. ie one is your adsl modem router and that will take the main router function. Your second router is really not working as a router, but as wireless access point (and switch if you plug things in).
That is perfectly fine. You are not roaming in this case since both routers are running different wireless names and networks.. but they are actually using same IP range.. all devices are on the one IP network with two different wireless access points.
4. If my dreams come true, the second router would be an Apple Airport Extreme (AX).
Apple router is fine for this. Easy to configure out of the box.
5. Yet, from reading posts and having my prior questions answered on this website, it may be that with an ADSL modem/router, all the ease and happiness of the Apple ecosystem is lost: while Apple routers seem to connect with each other easily, problems appear to arise when users try to inter-marry our non-Apple products with Apples.
The problem arises when you try and interconnect using wireless extend or repeater.. you are not using wireless to extend, you are using ethernet. Wired has no issues.
11. Based in part on LaPastenague’s earlier advice, I want to buy the TP-LINK TD-W8980 N600 Wireless Dual Band Gigabit ADSL2+ Modem Router (2.4GHz 300Mbps+5Ghz 300Mbps, IPv6 Compatible). This appears to be the most popular ADSL device on Amazon now.
Will this modem/router work EASILY with the Airport Extreme in the manner I’ve described? That is, connecting the two with a cable and creating two WI-FI networks.
It is a good choice.. It should be fine considering how poor your line is.. this modem is proving to have a couple of bugs.. it does not handle torrents well but I would suggest your system is not being used for that purpose. It has some port forwarding issues. Again you are probably not going to overload it.
12. Also, is it generally correct that the best way to connect them is with an Ethernet cable: https://discussions.apple.com/message/23759755#23759755
Absolutely best.. only decent method.
14. If this will work, what “mode” will the AX device be in (again, in order to have two separate networks with separate passwords)? I have heard of the “repeater”, “roaming” , and “bridge” modes.
Bridge. Although if it gives issues there is another method, although rather complex to setup.. not something to worry about now.
15. Are there two levels of passwords which need to be considered? Of course, there is the network and network passwords which we create here and which will be different. But, does the Apple also have to have the ISP password like the principle ADSL modem/router?
Only the adsl modem has the ISP authentication.. it is the box that does the link. The TC just piggy backs.
The passwords on the TC are for its Admin, wireless and disk access.
16. To set this up, what information do I need from the ISP (e.g., passwords, IPs…)?
For ADSL you must have the PPPoE authentication username and password.
So, whoever feels knowledgeable enough to reply to this post, please be sincere if you think it is better to avoid the Apple.
hmmm.. I am biased because I see the issues not all the good stories..
The latest airport and Time Capsule seem to have a few pretty severe bugs.. if they happen to hit you, they are extremely hard to fix if you are in the middle of Nepal. And Apple service centre is a long long way away.
I cannot answer your question from the point of view of a person on the ground in remote area. If the economics of the purchase works for you, great. Go for it.
In terms of wireless coverage.. the Asus AC models or Netgear R7000 kill the Apple. Sorry but it is just fact.
See reviews here.
http://www.smallnetbuilder.com/lanwan/router-charts/bar/113-5-ghz-dn-c
That is average.. if you look at the apple router in the worst location by changing the filters, it comes out worse again.
I cannot post the URL to our local forum here.. (apple doesn't allow it). But in testing with apple clients the asus still beat Apple router soundly.
Pure wireless range is not the only consideration.. but in a mixed environment and since the wireless on the 8980N is not too bad.. then buy Apple router for apple client devices makes good sense.
Maybe the older Gen5.. or two of them.. would do a better job.. with a bit more tested and known hardware.
One thing you do need to check.
Routers from every other brand allow you to select country. Any country from anywhere in the world. Apple routers do not.
If you buy an airport in North America it is coded to North America and offers just a few countries.. USA, Canada I suppose.. what else is North America??
You cannot change it to Nepal.
To get the one for Nepal you must buy the model that covers, South Asia I guess.. I am not sure which it is.
See what the license information is for wifi in Nepal as it might be very different to US and therefore illegal for you to run it in Nepal.
If only the whole world would just bow to America.. we could all follow the FCC regs..
http://en.wikipedia.org/wiki/List_of_WLAN_channels
This only applies to the Apple.. the TP-Link etc allows you to choose Nepal or correct country regulations for wifi.
Buying modems has one tricky bit.. that the actual adsl ATM channel is different in different parts of the world. No modem is usually impossible to setup but some can be difficult if it is pre-configured for US.. this is easy to overcome generally as you can download a firmware for another locality, so you can have local settings.

Is airport extreme a modem or just a router?

is airport extreme a modem or just a router? (do i have to plug it in to phone line or cable/dsl modem?) i dont want to lease a cable modem unless i have to. (expensivo!)

An AirPort Extreme base station (AEBS) includes a 56k modem for connecting to a dial-up ISP.
If you are using DSL or cable for Internet, you will need the appropriate modem in addition to the AEBS.

Is Airport Extreme a modem or router ?

Hi there,
Is Airport Extreme a modem or a router or both ?
I ask because I intend to buy to solve my problem but not sure if it is the correct product to purchase.
My problem it that I have a 2Wire modem *** router. It serves me fine all this while without problem until I bought an iMac. My iMac can connect wireless to the 2wire modem/router but very often after a few minutes of surfing the signal drops.
Will puchasing the Airport Extreme help ?
Is the connection goes like this:
Wall connect to 2Wire modem/router to Airport Extreme
(that means the signal from the wall first goes to the 2Wire, then from 2Wire goes to the Airport Extreme )
Then the iMac get wireless signal from Airport Extreme ?
Thanks

1. How do I disable wireless signal from the 2Wire...
You would need to consult the 2wire user's guide.
2. If I disabled the wireless signl from 2Wire, does that mean all my present gadgets like Xbox360, Wii, iPhone, PCs, wireless printer which are all currently connected via the 2Wire signal cannot be used ?
They would connect to the AEBS.
3. Can you please explain what you meant by "AEBS to act as a bridge (not sharing a single IP address)" ?
Use AirPort Utility to configure the AEBS to act as a bridge (not sharing a single IP address).
4. How to configure AEBS to act as a bridge ?
Use AirPort Utility.

Questions about AirPort Express and Extreme!

I have BT Infinty and the hub is situated in the living room. What I want to do is extend the wi fi to my room which is around 10 metres away.
Are you able to connect the AirPort Express to the network and then create a network for the AirPort Express for my MacBook Pro to connect to?
I have two options and questions
1. Buy a AirPort Extreme and replace my BT hub with that. Then use an AirPort Express to extend the wi fi. But when you extend the wi fi does it mean that when I search for a wireless hotspot from my Mac I connect the the AirPort Express? Or is there a way of making the AirPort express to have a different name?
2. Use my Bt hub and buy a AirPort Express and connect it to my Infinty Connection. BUT is there a way of making a hotspot for the AirPort Express for example
my Infinity connection is named Bt-Infinty2356
I use the AirPort express to connect it and extend the wifi
THEN is it possible to make a hotspot named "AirPort-Express-Muppet" for me to connect from my Mac?
Thanks

I have no experience with the "BT Infinity Modem" and "BT HomeHub", but I assume that they are two separate units?
If yes: connect the modem direct to the Extreme by ethernet cable.
If it is a "combined" unit: connect the Extreme by ethernet cable to one of the ethernet slots on the hub.
In both cases set the Extreme to "Create a wireless network".
Use a Airport Express to "extend a Wireless Network", and extend the Extreme.
Do not expect the Airport Express to extend the BT hub wireless network, because it will not work.
In both cases you have two wireless networks: one from the Hub and one from the Extreme.
Off the record: I have the same situation in France with the "Livebox" (Orange) that is connected to a Netgear WiFi router: two network: the Livebox is just that, the Netgear is "relayed" through Netgear Routers (Switches) to five areas in the "house". The same in Switzerland, but there I used Extreme and Express units instead of the netgear units.
The Hiome Hub should work fine connected to the modem by cable, and the other network also by connected to the cable. Do not mix the different brands: trouble.

Question about airport express/extreme and printing

Hopefully this question will make sense... I currently have my computer hooked up to Airport Extreme wirelessly. That is the network in my house. I want to buy a large format Epson printer and it needs to be somewhere else in the house and cannot be plugged in to the Extreme.
If I purchase the printer and plug it into an Airport Express that is plugged into an outlet can I switch back and forth between wi-fi connections to print wirelessly?
Thanks for any help.
Stephanie

If you receive a signal strong enough to use your computer wirelessly upstairs, you won't have any problem (I don't think) with your printer. I just got a Wi-Fi printer and it just seamlessly becomes part of your network same as adding any Wi Fi enabled device (I have 2 roku's for streaming Netflix etc and it all works great). BTW, my printer is a Canon MP 495 and so far I really like it. And, for a very inexpensive photo printer, (+AIO- copier, scanner, which I like, I paid around $45 on Amazon when it was on sale). The set-up instructions for Mac were not very coherent, but if you know what you are doing when it comes to adding hardware and working with your network, you can do it without the poorly written instructions. Also, the web site is not that great for help forums or shopping for ink, etc. Amazon is one of the best overall resources with lots of customer reviews, etc. Good luck!

Win XP Pro + Airport Extreme + 56k Modem

Hi,
I just recently bought an Airport Extreme Base Station with the 56k modem with the intents of connecting my 12" G4 PowerBook and 12" G4 iBook (both 2005) to the internet via the 56k modem. For the record, both connect perfectly, always, no hassle. (Albeit a bit slow at 48000, and it takes 60 seconds to logon and 60 to logoff)
The catch here, is I have an IBM T42 ThinkPad (2005) that can see this Airport too. But I have not been able to find a way to turn the modem on and/or off using the IBM. I do know about the Jon Sevy java bit, I do have it downloaded -- BUT -- how does one go about installing this thing? It's a .JAR file.
I also saw a better 'dialer' here by a person posting as 'KewlDawg'(?) that also may have worked, but the link is dead.
I did manage to find a dialer called 'InModem 0.1.0' by Jason Barry Morley, but it often doesn't want to hang-up after a session.
So as you can see, I have trying to resolve this myself, but not very successfully. Anyone have a better solution for the WinXP world?
I'm so upset Apple didn't see fit to provide this themselves. What an undersight. I wanted to buy one of these for my Brother as he is a Windows only person and heavily uses dialup. Oh well, no sale there.
I look forward to all and any suggestions. Thanx in advance!

Bottom line? No! The standard for Gigabit Ethernet was set to work with CAT-5 cabling. CAT-5e, especially at the length you plan on using, will show no improvement. CAT-6 is designed for 10 GBps networking.

2 airports 1 cable modem?

I have 2 Apple TVs connected to an Airport Express. Both ATVs reliably show up in iTunes Devices list. I want to replace Express with new Extreme but after much time and effort, I cannot get the 2 ATVs to show up in Devices list with my Airport Extreme. (This seems to be a common problem appearing over and over in this forum, and I have tried many of the suggestions.) When I replace the Airport Extreme unit with the Airport Express, both ATVs show up and syncing, internet access, etc. is fine.
My problem is I want to use the ethernet and USB ports on the Extreme (the Airport Express lacks these) and take advantage of the Extreme's stronger signal to reach a second computer (iMac) at the other end of the house.
My question is: Can I connect my cable modem to an A/B ethernet switch and connect the A and B ports of the switch to Airport Express (say, port A) and Airport Extreme (say, B) and then switch to A to access the network in which the Apple TV's appear and switch to B when I'm using the extra ethernet/USB ports of the Airport Extreme and the distant iMac.
I'm assuming I can set up 2 different internet networks (different names and passwords) on my main Mac and then choose which one I want to use at any given time.
Of course, all this would be unnecessary if the Airport Extreme would recognize the 2 ATVs and reliably list them in iTunes' Devices.

Phil,
I believe the topic is covered in the 'Airport Network Designs' section of the manual that came with your extreme.
So far as this being a widespread problem, it is one of the most recurring topics, however you should remember the forums are the place to come with a problem, rarely will anyone who doesn't have a problem put in an appearance, As a percentage of those who have bought tv's the number of these types of problem is really very tiny. Additionally not all networking problems are the same, for example some can connect to itunes but occasionally lose connection, others have issues with security protocols etc.
Add to that networking is something that most people find difficult, different hardware comes with different features and sometimes different names for the same features and often the features are set up in different ways. I believe that most networking issues are solvable, but diagnosing them can be quite difficult sometimes.

Constant Activity between Airport Extreme and modem

Hello all,
I am the recent owner of an Airport Extreme. My Aiport Extreme is connected to my VDSL modem through the WAN port.
In the Options menu, I set the option "Status Light" to "Flash on Activity".
Doing so, I discovered that there is always activity between :
1) the Airport Extreme => I can see the green led flashing every 4-5 seconds
2) the VDSL modem => I can see the network led of the modem flashing every 4-5 seconds in sync with the Airport Extreme
Initially, I thought it was "real traffic" coming either from wireless devices or ethernet devices... But after unplugging the ethernet cables (for the devices connected via cables) and after disabling the Wifi network of the Airport Extreme, the leds of both Airport Extreme and the modem were still flashing in sync every 4-5 seconds... Then, I also unchecked the "Set time automatically", and still, both leds were still flashing in sync at the same interval !
I am a bit lost !
I am wondering what there is traffic/activity happening every 4-5 seconds when no device (either via Ethernet or wifi) is connected.
Do you also face the same issue ? Do you know the reason of the almost permanent activity between the Airport Extreme and my VDSL modem ?
Thank you very much for your replies !
Regards,
trabala38

Hello Bob Timmons,
Thanks for your insight in this.
Well, actually, to be logical, this traffic between the WAN port of the Airport Extreme and my modem could be coming from
1) garbage/requests on the VDSL line from my ISP
2) requests from the Airport Extreme to my modem
If it is number 2, do you think that the Airport Extreme could query the modem every 4-5 seconds, i.e. to check that the Internet connection is alive ?
Thanks for your feedback,
Regards,
trabala38

Airport Extreme & X-Modem - is there a setup guide please?

I'm based in the UK and have recently purchased an X-Modem M3 ADSL modem to replace a Netgear router/modem in my home network. This modem will replace the Netgear and connect in to the WAN port of my Airport Extreme Base Station.
I can get the modem to connect and be recognised by the AEBS, to the point where the WAN port gets an IP address from my ISP.
However, from there, no matter what options I try, I cannot then get a DHCP scope up and running for my LAN and for those clients to connect to the internet.
I think its a problem with the DHCP/NAT/Bridge settings in the Airport Utility, so I was wondering if anyone has got this setup working and could offer some advice please as its driving me insane!
I've spoken to ADSL Nation, but as its an AEBS config issue, they've suggested phoning Apple.
Thanks,
Mike.

I'm thinking about getting tis combination too, this might help...
http://www.adslnation.com/knowledgebase/xmodem+airport-11n.php

Question about Airport Extreme, Cable Modems??

Similar Messages

Maybe you are looking for