Question about GENERAL WORKFLOW FOR DELIVERING DOLBY 5.1 FILE

what I have usually done with my videos is to export omf to logic , and mixed in 5.1, from there i bounce in multichannel audio file, and open it i compressor and create there my AC3 file.
is that all to get a professional accepted DOLBY DIGITAL FILE AUDIO file?
what is real professional workflow used in feature films and main studios? I SEE hardwares around as dolby e etc
please help me to clear my confusion

I've tried this myself and have had no luck with the resulting blu-ray 5.1 mix. When I import a 5.1 AC3 file into Encore as an asset and create a new Audio track, or when I open a Premiere CS5 project with a 5.1 master audio track and use dynamic link to send it to Encore, it always mixes it down as a stereo blu-ray.
I have the SurCode plug in activated as well. The blu ray file folder "STREAM" contains a file that I've tried importing into Premiere and when you look at the audio track it's always stereo, never 5.1

Similar Messages

General Workflow for documents Activation

Hi Gurus
I am using General workflow for documents to cater for the Absences approval process. However after I execute the process, the workflow is in ERROR state and showing me the following message
"Error when starting a SWITCH branch".
Any suggestion for the solution of the above error message?
Thanks & Regards
Waz

Hello,
Have you searched SDN?
There was a thread some time ago which was answered by this piece of knowledge from the SAP Help:
"The system checks conditions in the sequence specified. The workflow execution is continued using the outcome whose condition produces the value true first"
Maybe you could try changing the order of your conditions, if there is more than one.
What condition(s) are you using?
regards
Rick Bakker
Hanabi Technology

Questions about Feature Licenses for 1800, 2800, 3800, 2900, 3900 series ISRs

Hey all,
I have a question about feature licensing for Cisco ISR 1800, 2800, 3800, 2900 series. I know there are differences between all of the series. My main question which applies for all the Cisco ISR series is this:
"If I want to upgrade the IOS to a newer version and upgrade from the basic feature set, do I need to get a license from Cisco? "
If yes:
And if so, how do I go about purchasing a license? Is a support contract needed?
Again, I need to know for each Cisco ISR series. I'd appreciate any help on this.
Thanks,
John

You probably want to reach your SE/AM about this so they can explain you exactly how this works, maybe some sales material, or you can also reach pre-sales.

Hi, I have answered no to the question about saving password for one spesific site. I have changed my mind and would like Firefox to save the password. How do I reactivate the password saver for one spesific site?

Hi, I have answered no to the question about saving password for one spesific site. I have changed my mind and would like Firefox to save the password. How do I reactivate the password saver for one spesific site?

Check exception list of your Firefox password Manager and check if your site is there or not?
* http://kb.mozillazine.org/User_name_and_password_not_remembered#Password_Manager_settings

2 questions on BRF workflow for SC

Hello All
I have 2 questions on BRF workflow as follows:
1) My requirement is that the PO be created only after all the items in the Shopping cart (from all decision sets) are approved by separate agents. How do I enforce this using BRF ?The closest is Decision Type 3: Overall Decision for Partial Document (.The decision applies to the entire decision set)
2) IS it possible to send an approval work item to multiple agents ( Based on a role or custom attribute) and then the work item could be approved by any one of those agents which completes the workflow & deletes all other work items ?
Thanks
Kedar
Edited by: Kedar Ghayal on Jan 4, 2011 10:53 PM
Edited by: Kedar Ghayal on Jan 5, 2011 12:06 AM

Hi,
1) My requirement is that the PO be created only after all the items in the Shopping cart (from all decision sets) are approved by separate agents. How do I enforce this using BRF ?The closest is Decision Type 3: Overall Decision for Partial Document (.The decision applies to the entire decision set)
PO can only be created only if all approver's approve the SC. it will be great if you give more details about the requirement.
2) IS it possible to send an approval work item to multiple agents ( Based on a role or custom attribute) and then the work item could be approved by any one of those agents which completes the workflow & deletes all other work items ?
Yes - a workitem could be sent to multiple approver's for a decision set, once any one of the appprover approve the SC, the workitem will be deleted automatically from rest of approver's UWL..
Saravanan

Question about CPU usage for video playback

I've asked a related question already on the Safari forum, but would like some clarification, please.
The speed of this iMac is 400 MHZ and whenever I go to YouTube or almost any other site that requires video I see that the CPU usage can peak way up at 80% or more. I have Flash 9 installed which has a minimum of 500 MHZ, so I get pretty choppy video, but that's not the issue here. I can live with that. I keep any other applications closed. I'm often running a small fan over the top of the iMac to help vent the buildup of heat. I can monitor the temperature at the Hard Drive and I suppose that gives me an idea, of sorts, about general temperature conditions inside.
The answer I got was that this kind of CPU usage could be detrimental to the processor as it builds up excessive heat and to keep this kind of video to a minimum.
My question is can anyone roughly suggest what a maximum time on YouTube, for example, would be, 2 minutes, 5 minutes, is 10 minutes too long? I have plenty of RAM at 768. Some guidelines?
Thanks.

Hey WZZZ,
Thanks for the star and kind words.
I'm the de facto Mac guy at my kids' school and we have around 25 iMac Slot Loaders working there. You can imagine they get abused quite a bit. There are 10 running Garage Band in the Music Department. That puts a tremendous strain on the CPU and I'm actually surprised that they run it so well. My son had a 600 iMac running GarageBand, he was complaining that it was getting jumpy and when I looked at it he was running 10 unlocked tracks simultaneously! So now he has an eMac G4 800 and that of course runs a lot better.
So to sum up, with all the abuse of those machines in terms of the CPUs the problems I have with them have nothing to do with that. The problems have more to do with parts of the OS that they toss, headphone jacks abused, CDs jammed in the slots, and the like.
A couple of other related things. I've got Hardware Monitor, demo, installed and I think it reported it could only find the hard drive sensor, if I'm not mistaken - nothing else on this Mac with a sensor. Is that right?
I see references to CPU sensors on 400 iMacs but on the 400 I have here for repair Temperature Monitor reports no sensors. Perhaps there were different versions of the 400.
But very good to hear that the fan is a good idea for CRT related things. Should I keep the fan running-mostly for that hard core CRT stuff- even if the computer is sleeping and the room temp. is only around 62-64 F.? (We need to put on warm clothes to sit in front of this thing now, but worth it to keep this old machine happy).
On the one I did the fan pushed the airflow in the direction of the passive flow of the iMac - in at the bottom and out the grill by the handle.
One more question, more out of curiosity than anything else: If I move this small clip-on fan close to the case - right now it's about 3 feet away and the image is stable - the screen begins to flicker and flutter quite a lot. My theory is that that's happening not necessarily because of electro-magnetic interference from the fan motor, but rather, because the back of the tube is getting cooled unevenly. What do you think?
Well the classic failures that I see in the iMac are in this order:
1) Dielectric breakdown of the flyback transformers internal insulation. This is heat/age related and a common problem with CRTs in general.
2) Breakdown of high voltage electolytic capacitors and regular high voltage capacitors on the neck board and PAV supply.
3) Solder problems with the flyback itself. This is diagnosed by the upside down boot technique.
I used to repair these problems but now it's easier for me to swap the Firewire boards into working 350s. I've got 12 of those in the basement currently.
Richard

Question about firefox permissions for sites

i have a question about sites permissions
in google chrom it is easy to set permission for each site like (java, flash plugin, image , ...)
http://i58.tinypic.com/nl66v9.png
but i prefer to use firefox
is there any addon or something else to have this options in firefox ?

You can inspect and manage the permissions for the domain in the currently selected tab via these steps:
*Click the "[[Site Identity Button|Site Identity Button]]" (globe/padlock) on the location/address bar
*Click "More Information" to open "Tools > Page Info" with the Security tab selected
*Go to the Permissions tab (Tools > Page Info > Permissions) to check the permissions for the domain in the currently selected tab
You can inspect and manage the permissions for all domains on the about:permissions page.
*https://support.mozilla.org/kb/how-do-i-manage-website-permissions

Simple question about Portal Workflow

Hi.
Is possible use Portal Workflow in order to use the UWL to inform a task for KM document for Approval process, without a backend connection with a SAP business workflow ??
thanks in advance.
Leandro

thanks Deepa. I solved it.
the problem was that the iview for "my task" I am using, is different the "my task" iview in eu_role role, and the approval workflow tasks not appear in my iview, and I confuse about de workflow without backend for this cause.

HT3702 Hi I would like to ask a question about my billing for some things

I would like to ask a question about my billing

This is not Apple. These are user forums. Questions about billing, credit cards, etc. should be addressed directly to Apple.
Apple Store Customer Service at 1-800-676-2775 or visit online Help for more information.
To contact product and tech support visit online support site.
For Mac App Store: Mac App Store Customer Service.
For iTunes: Apple Support for iTunes - Contact Us

Questions about the content of download meeting recording .zip file

I tried posting this on the resurrected Connect forum, but my Adobe ID wasn't recognized there....
Concerning the files that are included in the .zip file of the meeting recording that can be downloaded:
1) Is there any documentation describing the files and their contents (i.e. what each file represents, what each XML element and attribute in those files represent)
2) Are there any files that capture mouse movement on a shared desktop?
Thank you!

Hi Sean,
Regarding your first post:
Thanks Jorma! I don't have access to an FMS build at the moment but I'm quite certain it's there. As for contacting Jaydeep, I am 90% sure he authorized us to broadcast his email on here if folks had questions about the tool, but, in the case that I'm wrong and he didn't - I'm going to double-check first.
Regarding your most recent post..
"To be clear, the most critical goal I'm trying to accomplish is to create an automated process that will download the recording meeting at its highest quality in a consistent and reliable manner".
I personally believe this is possible; unfortunately, I haven't seen it done yet. If your recording contains:
- audio
- a camera feed
- screensharing
Then I think you might be able to get this going. If it contains shared content, like a shared PPT, this gets trickier.
"To do this, of course, I have to reproduce some of the functionality that Connect provides, starting and combining video and audio streams according to the instructions in the control files."
Exactly right. If your recording didn't contain shared content, then all you've got on your hands are a bunch of audio/video files that you could edit together as you wanted with your favourite video editing tool. If it contains shared content, here's (at a high level) what's happening.
For shared PPTs or FTContent files:
First (for version 9 recordings only), Connect reads the information on the Shared Content's location and SCO within mainstream and indexstream and validates it before loading it. I don't recall this happening to the same extent with version 8 or earlier, but maybe it was. Now, if the content is validated (ie. Connect can find it) the share pod will display as black, if it doesn't, you get an empty pod with an message like "No content is being shared" or something like that.
Connect then looks at the actual FTContent file, and loads the content that is to be shared using the file path and sco ID listed in here. It's important to note that the SCO ID and file path in here will likely not be the same as the original file you uploaded to your room, it's a new SCO id (I believe SCOs of this type are called referenced scos) and new path.
Now...if I was going to build some sort of player which would play all these files in one screen to make a recording...I might not want to use Connect's code here. If you know the file path to the shared content (from FTContent), you could easily view it with the content URL (conveniently also in FtContent). I'm not a coder, but I'm envisioning something like Presenter's GUI where you've got the presentation's content in the main area, and a video file (if there is one) playing back on the side.
Anyways, food for thought if you want to try to go about this. Connect recordings are incredibly complex and they come with a big learning curve, but if you can make sense of them the knowledge is quite valuable.

PXI 2527 & PXI 4071 -Questions about EMF considerations for high accuracy measurements and EMF calibration schemes?

Hi!
I need to perform an in-depth analysis of the overall system accuracy for a proposed system. I'm well underway using the extensive documentation in the start-menu National Instruments\NI-DMM\ and ..\NI-Switch\ Documenation folders...
While typing the question, I think I partially answered myself while cross-referencing NI documents... However a couple of questions remain:
If I connect a DMM to a 2 by X arranged switch/mux, each DMM probe will see twice the listed internal "Differential thermal EMF" at a typical value of 2.5uV and a max value of less than 12uV (per relay). So the total effect on the DMM uncertainty caused by the switch EMF would be 2*2.5uV = 5uV? Or should these be added as RSS: = sqrt(2.5^2+2.5^2) since you can not know if the two relays have the same emf?
Is there anything that can be done to characterize or account for this EMF (software cal, etc?)?
For example, assuming the following:
* Instruments and standards are powered on for several hours to allow thermal stability inside of the rack and enclosures
* temperature in room outside of rack is constant
Is there a reliable way of measureing/zeroing the effect of system emf? Could this be done by applying a high quality, low emf short at the point where the DUT would normally be located, followed by a series of long-aperture voltage average measurements at the lowest DMM range, where the end result (say (+)8.9....uV) could be taken as a system calibration constant accurate to the spec's of the DMM?
What would the accuracy of the 4071 DMM be, can I calculate it as follows, using 8.9uV +-700.16nV using 90 days and 8.9uV +- 700.16nV + 150nV due to "Additional noise error" assuming integration time of 1 (aperture) for ease of reading the chart, and a multiplier of 15 for the 100mV range. (Is this equivalent to averaging a reading of 1 aperture 100 times?)
So, given the above assumptions, would it be correct to say that I could characterize the system EMF to within 8.5uV+- [700.16nV (DMM cal data) + 0.025ppm*15 (RMS noise, assuming aperture time of 100*100ms = 10s)] = +-[700.16nV+37.5nV] = +- 737.66nV? Or should the ppm accuracy uncertainties be RSS as such: 8.5uV +- sqrt[700.16nV^2 + 37.5nV^2] = 8.5uV +-701.16nV??
As evident by my above line of thought, I am not at all sure how to properly sum the uncertainties (I think you always do RSS for uncertainties from different sources?) and more importantly, how to read and use the graph/table in the NI 4071 Specifications.pdf on page 3. What exactly does it entail to have an integration time larger than 1? Should I adjust the aperture time or would it be more accurate to just leave aperture at default (100ms for current range) and just average multiple readings, say average 10 to get a 10x aperture equivalent?
The below text includes what was going to be the post until I think I answered myself. I left it in as it is relevant to the problem above and includes what I hope to be correct statements. If you are tired of reading now, just stop, if you are bored, feel free to comment on the below section as well.
The problem I have is one of fully understanding part of this documenation. In particular, since a relay consists of (at least) 2 dissimilar metal junctions (as mentioned in the NI Switch help\Fundamentals\General Switching Considerations\Thermal EMF and Offset Voltage section) and because of the thermo-couple effect (Seebeck voltage), it seems that there would be an offset voltage generated inside each of the relays at the point of the junction. It refeers the "Thermocouple Measurements" section (in the same help document) for further details, but this is where my confusion starts to creep up.
In equation (1) it gives the expression for determining E_EMF which for my application is what I care about, I think (see below for details on my application).
What confuses me is this: If my goal is to, as accurately as possible, determine the overall uncertainty in a system consisting of a DMM and a Switch module, do I use the "Differential thermal EMF" as found in the switch data-sheet, or do I need to try and estimate temperatures in the switch and use the equation?
*MY answer to my own question:
By carefully re-reading the example in the thermocouple section of the switch, I realized that they calculate 2 EMF's, one for the internal switch, calculated as 2.5uV (given in the spec sheet of the switch as the typical value) and one for the actual thermocouple. I say actual, because I think my initial confusion stems from the fact that the documenation talks about the relay/switch junctions as thermocouples in one section, and then talks about an external "probe" thermocouple in the next and I got them confused.
As such, if I can ensure low temperatures inside the switch at the location of the junctions (by adequate ventilation and powering down latching relays), I should be able to use 2.5uV as my EMF from the switch module, or to be conservative, <12uV max (from data sheet of 2527 again).
I guess now I have a hard time believeing the 2.5uV typical value listed.. They say the junctions in the relays are typically an iron-nickel alloy against a copper-alloy. Well, those combinations are not explicitly listed in the documenation table for Seebeck coefficients, but even a very small value, like 0.3uV/C adds up to 7.5uV at 25degC. I'm thinking maybe the table values in the NI documentation reffers to the Seebeck values at 25C?
Project Engineer
LabVIEW 2009
Run LabVIEW on WinXP and Vista system.
Used LabVIEW since May 2005
Certifications: CLD and CPI certified
Currently employed.

Seebeck EMV needs temperature gradients , in your relays you hopefully have low temperature gradients ... however in a switching contact you can have all kind diffusions and 'funny' effects, keeping them on same temperature is the best you can do.
Since you work with a multiplexer and with TCs, you need a good Cold junction ( for serious calibrations at 0°C ) and there is the good place for your short cut to measure the zero EMV. Another good test is loop the 'hot junction' back to the cold junction and observe the residual EMV. Touching (or heating/cooling) the TC loop gives another number for the uncertainty calculation: the inhomogeneous material of the TC itself..
A good source for TC knowledge:
Manual on the use of thermocouples in temperature measurement,
ASTM PCN: 28-012093-40,
ISBN 0-8031-1466-4
(Page1): 'Regardless
of how many facts are presented herein and regardless of the percentage
retained,
all will be for naught unless one simple important fact is
kept firmly in mind.
The thermocouple reports only what it "feels."
This may or may not the temperature of interest'
Message Edited by Henrik Volkers on 04-27-2009 09:36 AM
Greetings from Germany
Henrik
LV since v3.1
“ground” is a convenient fantasy
'˙˙˙˙uıɐƃɐ lɐıp puɐ °06 ǝuoɥd ɹnoʎ uɹnʇ ǝsɐǝld 'ʎɹɐuıƃɐɯı sı pǝlɐıp ǝʌɐɥ noʎ ɹǝqɯnu ǝɥʇ'

I have a question about the downloads for CS4.

I had to go back to CS4 Master Suite after my card was deactivated, because adobe got hacked and my credit card was compromised. Since I was in the middle of traveling and I'm still in a bad situation, because of it I am still on CS4. Which sucks for my workflow now.
Well, anyway... Sorry, still very frustrated.
When all that happened I had to download CS4 Master Suite from your site, because the disks are not with me. Photoshop continuously shutdown on me. If I attempt to move a layer up or down in the layers panel it froze and shutdown every freaking time. After Effects and Premier Pro could not export or render anything. Illustrator did what it's supposed to do most of the time. Photoshop, Illustrator, After Effects, and Premiere Pro are the only programs I use really. They are essential to my freelance work and I have had to turn away projects ever since this whole ordeal started last year.
About a month ago removed CS4 and downloaded Creative Cloud again, because I thought I was in a place were my bank could send me a card. Some how I received another monthly trial and everything was awesome again while I waited for my card. My card didn't come. The trial ended and now I'm right back to not being able to integrate with Cinema 4D and so on. Now that is not your fault. So, I'm not going there.
I did, once again, download the install file for CS4 Master Suite and install the same programs. They are just as problematic as they were the first time I used the .dmg file from your downloads site.
Now I know you are far away from CS4, but that is what I am on until I can get back to the US and get another card, because you don't accept paypal or anything else.
Is there anyway I can get an actual proper working install of CS4. I can work around all the features I lost if I can get a download that actually has everything it's supposed to have in it. I do not pirate software, which is why I went backwards. So, please, please, please, please do something about that .dmg that doesn't have everything need to make the program work properly.
Thank You,
From

Your technical issues have zero to do with the installers. Whatever is at play is rooted on your system, but you have not provided any specific system info nor crash logs. Pardon me, but "Photoshop is crashing" is a useful as my 88 year old grandma telling me her phone doesn't work...
Mylenium

Question about partner determination for customer master

Hi, experts,
I have already read the documentation about this topic at forum. Still I have the following question:
why should we assign the partner function to the account group? According to my understanding, the partner function has to be assigned to partner determination procedure and then through partner determination it is associated with the account group. If the partner can be assigned to account group directly, why do we still need determination procedure?
Best regards,
Fan

Hi
Let us consider an existing Partner Determination procedure in standard SAP.
The Partner Determination Procedure (e.g, ABCD) can contain multiple "Partner Functions". Suppose there are 100 numbers of Partner Functions in the Procedure.
We assign "Partner determination Procedure" to the "Account Group", so that , the assigned Procedure will be applicable for the Customer master data created under that Account group.
Suppose, Partner determination Procedure "ABCD" has been assigned to Account Group "XYZ".
Now, any Customer created under Account Group "XYZ", the Procedure "ABCD" will be applicable for them. Right?
We have already discussed , the Procedure "ABCD" contains 100 different "Partner Functions".
Out of these 100 Partner Functions, only those Partner Functions, which are permitted by the Account Group "XYZ" , they can only be entered in the Sales area data > Partner Function tab of the Customer master data.
Suppose, only 6 Partner functions (out of 100 no) are assigned to Account Group "XYZ".
So these 6 Partner Functions are permitted by the said Account Group "XYZ" and these 6 Partner Functions can only be entered in the Customer master data.
So, to summerise it, if you want to enter a Partner Function in the Customer master, then
- First, that Partner Function must be available in the Procedure which applicable, and
- Second, that Partner Function also must have been permitted (assigned) by the Account Group .
I hope, it is clarified.
Regards
Pradyumna

Where is the best place to ask questions about NetBeans 6 for Java?

When it comes to Java discussions, all I can think is this forum, but what about Java Desktop Applications using NetBeans IDE 6?
Question/Query 1:
I just like to ask how I can make the Database Application Template under the Java> Java Desktop Application> Database Application:
Well, the the nice Frame with prebuilt components are good, but how can we customize the Window Icon? Has anybody in this forum and particularly Netbeans 6 users encountered the same scenario?
Question/Query 2:
How can I make a splash page with such a Database Application template too?

Hello Andy,
we talk about Photoshop, or? In this case you should use Photoshop General Discussion
You will find all the (other) communities by clicking "Adobe Communities" on the top of the window. Please have a look at
https://forums.adobe.com/welcome (see screenshot) and/or open "All communities"
Hans-Günter

Question about Programming Notes for WD Abap / Context

http://help.sap.com/saphelp_nw04s/helpdata/en/03/0048413e466e24e10000000a155106/frameset.htm
Since an instance of the follow-on view has not yet been created, you must now decide whether to configure a component controller context with an appropriate mapping, or whether to fetch and check the data in an auxiliary class first and only pass it to the context of the follow-on view after navigation is completed. An application developer would, of course, prefer to use the context mapping method; using an auxiliary class, however, improves performance significantly.
Hello all,
If a fetch the data with auxiliary class, in which method do i fill the context of view after view is shown? The context of controller is mapped to view. Must it be done in supply function? But supply function is only one and i want to use a single context node for different views.
Another question. Does it make sense to fetch the data for a certain follow-on view
although navigation to this view will be definied late in a window?
Thanks
Regards
Paul

Hi Phil,
Ideally, on a custom method on the Component controller. or secondary controller.
This method should call an Auxiliary ABAP class that actually gets data.
Your Comp controller method would be triggered by an Event on you view.
EG Button to navigate, a check button whatever.
If i call the method of component controller in a method of my view, check the return code and only then do the navigation by firing an event. I think, it will work. What advantages will i get by calling a method of component controller via an Event?
generally I avoid that if at all possible.
but it's been done before. Main reason is to avoid unnecessary
navigation. Through the errors and perform the checks as close to source
as possible. in mots cases you should be able to check data, and even load
info before actually doing the navigation.
ie Avoid firing plug till the last moment.
For example, if have a "Next"-Button in a view. How can i decide in Method for "Next" what data must be filled for next view if in one case it could be one view, and in another case other? I thought, follow-up view must get data on his own. My question was, which method can be used for filling the data in this case. It is not wddoinit and not wddomodify.
Regards
Paul

Question about GENERAL WORKFLOW FOR DELIVERING DOLBY 5.1 FILE

Similar Messages

Maybe you are looking for