Question about ghost copy of an old hardrive

Okay i have a ghost copy of a hardrive i have have on my pc. if i were to set up boot camp could i put the ghost on my mac?

Hi,
have a look at the instructions here: http://discussions.apple.com/thread.jspa?messageID=9632453&#9632453
Hope it helps
Stefan

Similar Messages

Question about using new battery in old Powerbook

I have a pre-intel Powerbook G4, and the battery is pretty much toast (lasts about 15 minutes now). I have ordered a new battery for it, and I have this question about using it:
Am I smarter to keep the new strong battery out of the PB most days (as I usually work with it plugged in at home) and just pop it in when I know I will be out surfing on batteries? Or is it just as good living in my laptop 24/7 and only occasionally being called upon to do its job?
Current bad Battery Information below:
Battery Installed: Yes
First low level warning: No
Full Charge Capacity (mAh): 1144
Remaining Capacity (mAh): 1115
Amperage (mA): 0
Voltage (mV): 12387
Cycle Count: 281
thanks folks, Shereen

Hi, Shereen. Every Powerbook battery wants to be used — drained and then recharged — at least every couple of weeks. If you've always used your Powerbook on AC power nearly all the time, and not followed that pattern of discharging and recharging the battery every week or two, it's possible that your use habits have shortened the lifespan and prematurely diminished the capacity of your old battery. Of course it's also possible that your battery is merely old, as a battery's capacity also diminishes with age regardless of how it's used. You didn't say how old the battery is in years, so this may or may not be an issue. I mention it only because it can be an issue.
For general information on handling a battery for the longest possible lifespan, see this article. My advice on the basis of that article and long experience reading these forums is that it would be OK to do as you propose, but I doubt that you'd derive any significant benefit from it. You would still want to be sure of putting the new battery through a charge/discharge cycle every week or two, even if you didn't have a reason to use the Powerbook away from home or your desk, because sitting unused outside the computer is just as bad for a battery as sitting unused inside it. And you should never remove the battery from your computer when it's completely or almost completely discharged and let it sit that way any longer than a day or two.
Message was edited by: eww

Question about trying to install an old program

I am trying to install music writing software from a CD. This software has worked well for me on XP and Windows 7. When I tried to run it from the disk, I got an error message. So, I went through the whole "compatibility mode" process, trying it
in both XP and Windows 7 modes, without success. The installation process would begin, but then it would hang up. The software in question is called "Mozart," and I am attempting to run an early version, Mozart 6. The website for the software is
mozart dot co dot uk.
Now, here's the rub: I posted a question about this at the Mozart Software Yahoo Group, and one participant there said that he had installed Mozart 6 on a Windows 8 computer without difficulty. So, the question becomes, what am I doing wrong? Or do I have
a hardware problem? I have a new Toshiba laptop with 6 gigs of ram. I have Avast anti-virus software as well as Spybot anti-spyware software - could one of those be blocking a program installation from the disk drive?

Did you try download the latest version or applied the latest service pack?
This software is not free, you can also contact them for better support
Also using 2 antivirus is not recommended. You also can try to disable them, disable UAC and disable firewall to check

Question about variable copying, referencing and LinkedList constructors.

Is there any advantage in this recommendation?
"In general, do make sure that you copy mutable arguments and mutable return values when appropriate."
Now, according to this suggestion:
public ClassName(LinkedList<String> list)
     this.list = new LinkedList<String>(list);
Instead of public className(LinkedList<String> list)
     this.list = list;
}I am confused about the situation where using the copy constructor would be appropriate as opposed to the second method.
Can someone please explain which would be an ideal situation to use a copy constructor and when to use mere assignment?

fantastic_ray wrote:
Is there any advantage in this recommendation?
"In general, do make sure that you copy mutable arguments and mutable return values when appropriate."If you don't copy mutable arguments and return values, then when you change the state ("contents") of the object, it will be seen by both the original reference and the copy. Sometimes you may want this. Sometimes you may know that no change will occur. You have to judge what's appropriate for your use. In general, though, if there's a chance the elments' states may change, you'll want to copy them.
>
Now, according to this suggestion:
public ClassName(LinkedList<String> list)
     this.list = new LinkedList<String>(list);
Instead of public className(LinkedList<String> list)
     this.list = list;
It depends. After you do new ClassName(list), if the code that created the ClassName object is going to keep using the list and you don't want any changes it makes to be seen by the new object and vice versa, then yes, you'd want to do the former.

Question about automatic copying to library and Movies

I have my mac set to automatically copy any audio that is put in iTunes into my itunes folder because I like the way that it gets organized in there. Recently I have been ripping my DVDs using Handbrake so that I have digital copies of them on my hard drive. I want to put the movies into iTunes to make them more accessible, but I don't want them to be copied into my itunes library because I like to keep them in my Movies folder. Is there any way to avoid them being copied but still have my songs be copied over to the itunes folder?

No. You will have to turn off the prefs to copy to the iTunes music folder when adding to library then turn it back on.

Question about directory copying

Hi all:
Does anyone know how to implement to make a deep copy of a directory ? is there a API can do this ?
thanks in advance.

I've always done a breadth first recursive copy checking for file types as I go: anybody else?

Question about tranferring data from iPhone 3gs to iPhone 4

I just had a couple quick questions about transferring data from my old phone from my new iPhone 4. The reason i am wondering is because i am worried about whether i will encounter any problems when doing so.
First off i have already sold my phone today, i reset all data and settings from the phone and gave it to my buddy so its gone. I did a full sync and backup yesterday so all the necessary files should be on my computer(windows 7). Now, im basically wondering if i will run into any problems if i restore my iphone 4 from a backup. My 3gs was running 3.1.2 on att. Now i know IDEALLY i would have updated it to iOS 4 before backing it up and used the newest version of itunes, but i did not. Does anyone think this will be a problem for me?
Now with that out of the way, my biggest fear is losing my old data(text messages and notes mainly because i am a pack rat for those type of things) so id like to be SURE that none of my old backups will be deleted in any scenario. The reason i dont just restore it right now is because i want my new phone to be as clutter free as possible. I am going to be putting on here only the apps that i used often and would basically like to transfer over the BARE minimum; texts, notes, and highly used apps... So i guess my main question is can you transfer over only certain things like texts and notes after setting up the phone as a new phone. And if i were to set up the phone as a new phone what would happen to my old backups? Would i be able to selectively restore?
Im afraid that it might not be a possibility to transfer only certain things even though it should be.. i should be able to select a text messages folder and put it on my new phone and be done with it... But anyway i dont want to rant. Can anyone explain to me how this all will work?
ULTIMATE GOAL: Transfer only texts, notes, certain apps(and their data) and NOTHING ELSE.
MOST IMPORTANT THING: Not losing texts and notes. I can deal with putting all the old **** on my new phone and cluttering/slowing it down if i NEED to.
Thank you in advance, sorry for the long post.

If the most important thing for you is keeping old text messages, notes, and voicemail, then you'll need to sync the phone from your existing backup. I know of no other way to access those items.
Once you have synced to the new phone, check that you have those items that were important. Then you can reconnect your phone to iTunes, and change the sync settings to remove the apps or other items you no longer want to keep on the phone.
iPhone backups are stored by iTunes; you can see them by opening your iTunes preferences, clicking on "Devices" and then looking in the window. You can delete old backups from here. I don't know how you can open/read the backups though.
I don't expect you'd have any problems syncing from your old phone's backup, but it's definitely an either/or situation. Since you got rid of the old phone already, it's too late to email yourself your notes, or copy the text messages. Your previous backup is your only solution.

How can i copy itunes from ext.hardrive t o mac itunes, when i try igot a question? (if i want to delete my old itune and copy my new itunes to finder)) not sure how to cmby bough itunes in finder

PLEASE somebody....how can i copy itunes from ext.hardrive to mac itunes, when i try i got a question? (if i want to delete my old itune and copy my new itunes to finder)) not sure how to cmby bough itunes in finder.

PLEASE somebody....how can i copy itunes from ext.hardrive to mac itunes, when i try i got a question? (if i want to delete my old itune and copy my new itunes to finder)) not sure how to cmby bough itunes in finder.

Follow-up on question about copying 10.4

I only got one reply to my question about how to copy OS 10.4 from one internal drive to another and unfortunately, the response was cut short. Something about if I had another computer with Firewire, using it and that's as far as the response went. Yes, I have a laptop and have Firewire, but still don't know how to use it to help.

If you just wish to make a duplicate of one hard drive to another hard drive in the same G5, then do this:
Clone using Restore Option of Disk Utility
Open Disk Utility from the Utilities folder.
Select the destination volume from the left side list.
Click on the Restore tab in the DU main window.
Check the box labeled Erase destination.
Select the destination volume from the left side list and drag it to the Destination entry field.
Select the source volume from the left side list and drag it to the Source entry field.
Double-check you got it right, then click on the Restore button.
Destination means the second internal drive. Source means the internal startup drive.

Question: about to purchase ipad air - how do I migrate contacts,bookmarks,and address books from either an iMac or old macbook?

Question: about to purchase ipad air - how do I migrate contacts,bookmarks,and address books from either an iMac or old macbook?

Set up iCloud on both devices
How to set up iCloud on all your devices
http://www.apple.com/icloud/setup/

Hello , how r u, can i ask 1 question about xcode, i have mac os x 10.7.5 , n xcode version 4.6.3 i want build apps for ios 7.1 n mac os 1.9 ,, , but my macbook is old late 2008 macbook 4,1, so can i develop apps for ios7 n 1.9 using xcode 4.6.3, bcz my

hello , how r u,
can i ask 1 question about xcode, i have mac os x 10.7.5 , n xcode version 4.6.3 i want build apps for ios 7.1 n mac os 1.9 ,, , but my macbook is old late 2008 macbook 4,1, so can i develop apps for ios7 n 1.9 using xcode 4.6.3, bcz my machine cant upadte on 1.8 n 10.9,, ihave 2gb ram . core 2 duo pr, plz rely asap,
thnxs

Please type complete sentences and words. This isn't an instant message program.
https://developer.apple.com/support/ios/ios-dev-center.html

Question about source system copy for BW

Dear all,
I have a quick question about copying a source system for BW.
We have two clients in the source ERP:
100 Customizing
200 Testing
Our BW is only linked to client 200, so when we now delete client 200 and make a copy from 100 to 200, are we then still able to restore the source system connection so that our extraction will work, or will it fail, as in client 100 I have no BW related (except the cross-client-objects like datasource) information, that can be used for a possible restore of this connection.
What is the procedure in this case?
Thanks,
Andreas

Unfortunately, you will lose your source connection and need to create a new one in R/3. You can use the same source system name in BW, but check the source system connection after the copy (SM59). Also, I would "Restore" the source system (in BW, right-click on Source system in RSA1, and click "Restore") to insure the datasources get replicated from R/3 to BW.
Depending on how much you want your BW and R/3 systems to be in synch, you will need to rebuild all your data providers (cubes/ODS's) from your R/3 system. This means deleting all the data and running the initializations from scratch. At the very least, you will need to rebuild the delta queues.
Curious, if 100 is just for customizing, is there any data in it? Are you just creating a new blank client 200?

I wont to fix my old id account my email is and when you whant to reset the password i dont recieve any email from apple id and when you answer question about your birth date it says not file is found.

When i try and reset my id account it says it has been blocked for security reason. When you answer question about your birth date no souch record found and when i resset it by email io dont recieve any email from apple id reseat password. can anyone hep me ?
<Email Edited by Host>

Security questions:
https://discussions.apple.com/docs/DOC-4551
http://support.apple.com/kb/HT5312

Some questions about Muse

First of all, I would like to say that I am very impressed with how well Muse works and how easy it was to create a website that satisfies me. Before I started a daily updated website I thought I would encounter many problems I will not be able to solve. I have only had a few minor issues which I would like to share with you.
The most problems I have with a horizontal layouts (http://www.leftlane.pl/sty14/dig-t-r-3-cylindrowy-silnik-nissana-o-wadze-40-kg-i-mocy-400- km.html). Marking and copying of a text is possible only on the last (top) layer of a document. The same situation is with widgets or anything connected with rollover state - it does not work. In the above example it would be perfect to use a composition/tooltip widget on the first page. Unfortunately, you cannot even move the cursor into it.
It would be helpful to have an option of rolling a mouse to an anchor (like in here http://www.play.pl/super-smartfony/lg-nexus-5.html and here http://www.thepetedesign.com/demos/onepage_scroll_demo.html). I mean any action of a mouse wheel would make a move to another anchor/screen. It would make navigation of my site very easy.
Is it possible to create a widget with a function next anchor/previous anchor? Currently, in the menu every button must be connected to a different anchor for the menu to be functional.
A question about Adobe Muse. Is it possible to create panels in different columns? It would make it easier to go through all the sophisticated program functions.
The hits from Facebook have sometimes very long links, eg.
(http://www.leftlane.pl/sty14/mclaren-p1-nowy-krol-nurburgring.html?fb_action_ids=143235557 3667782&fb_action_types=og.likes&fb_source=aggregation&fb_aggregation_id=288381481237582). If such a link is activated, the anchors in the menu do not work on any page. I mean the backlight of an active state, which helps the user to find out where on page they currently are. The problem also occurs when in the name of a html file polish fonts exist. And sometimes the dots does not work without any reason, mostly in the main page, sometimes in the cooperation page either (http://www.leftlane.pl/wspolpraca/). In the first case (on main page), I do not know why. I have checked if they did not drop into a state button by accident, moved them among the layers, numbered them from scratch and it did not help. In the cooperation page, the first anchor does not work if it is in Y axle set at 0. If I move it right direction- everything is ok.
The text frame with background fill does not change text color in overlay state (http://www.leftlane.pl/sty14/nowe-mini-krolestwo-silnikow-3-cylindrowych.html). I mean a source button at the beginning of every text. I would like a dark text and a light layer in a rollover, but the text after export and moving cursor into it does not change color for some reason.
I was not sure whether to keep everything (whole website) in one Muse file (but I may be mistaken?). I have decided to divide it into months. Everyone is in a different Muse file. If something goes wrong, I will not have any trouble with an upload of a whole site, which is going to get bigger and bigger.
The problem is that every file has two master pages. Everything works well up to the moment when I realize how many times I have to make changes in upper menu when I need to add something there. I have already 5 files, every with 2 masters. Is there any way to solve this problem? Maybe something to do with Business Catalyst, where I could connect a menu to every subpage independently, deleting it from Muse file? Doing so I would be able to edit it everywhere from one place. It would make my work much easier, but I have no idea jendak how to do it.
The comments Disqus do not load, especially at horizontal layouts (http://www.leftlane.pl/sty14/2014-infiniti-q50-eau-rouge-concept.html). I have exchanged some mails and screenshots with Disqus help. I have sent them a screenshot where the comments are not loaded, because they almost never load. They have replied that it works at their place even with attached screenshot. I have a hard time to discuss it, because it does not work with me and with my friends either. Maybe you could fix it? I would not like to end up with awful facebook comments ;). The problem is with Firefox on PC and Mac. Chrome, Safari and Opera work ok.
YouTube movie level layouts do not work well with IE11 and Safari 7 (http://www.leftlane.pl/sty14/wypadki-drogowe--004.html). The background should roll left, but in the above mentioned browsers it jumps up. Moreover the scrolling with menu dots is not fluent on Firefox, but I guess it is due to Firefox issues? The same layout but in vertical version rolls fluently in Firefox (http://www.leftlane.pl/sty14/polskie-wypadki--005.html).
Now, viewing the website on new smartphones and tablets. I know it is not a mobile/tablet layout, but I tried to make it possible to be used on mobile hardware with HD (1280) display. I mean most of all horizontal layouts (http://www.leftlane.pl/sty14/2015-hyundai-genesis.html), where If we want to roll left, we need to roll down. Is there a way to make it possible to move the finger the direction in which the layout goes?
On Android phones (Nexus 4, Android 4.4.2, Chrome 32) the fade away background effect does not work, although I have spent a lot of time over it (http://www.leftlane.pl/lut14/koniec-produkcji-elektrycznego-renault-fluence-ze!.html). It is ok on PC, but on the phone it does not look good. A whole picture moves from a lower layer instead of an edge which spoils everything.
This layout does not look good on Android (http://www.leftlane.pl/sty14/nowe-mini-krolestwo-silnikow-3-cylindrowych.html#a07). The background does not fill the whole width of a page. There are also problems with a photo gallery, where full screen pictures should fill more of a screen.
Is it possible to make an option of scroll effects/motions for a fullscreen slideshow widget thumbnails (http://www.leftlane.pl/sty14/2014-chevrolet-ss%2c-rodzinny-sedan-z-415-konnym-v8.html#a06)? It would help me with designing layouts. Currently, it can go from a bottom of a page at x1 speed or emerge (like in this layout) by changing opacity. Something more will be needed, I suppose.
Sometimes the pictures from gallery (http://www.leftlane.pl/sty14/2014-chevrolet-ss%2c-rodzinny-sedan-z-415-konnym-v8.html#a06 download very slowly. The website is hosted at Business Catalyst. I cannot state when exactly it happens, most of the time it works ok.
I really like layouts like this (http://www.leftlane.pl/sty14/2014-chevrolet-ss%2c-rodzinny-sedan-z-415-konnym-v8.html#a03). On the top is a description and a main text, and the picture is a filled object with a hold set at the bottom edge. That is why there is a nice effect of a filling a whole screen- nevertheless the resolution that is set. It works perfect on PC, but on Android the picture goes beyond the screen. You can do something about it?
In horizontal layouts (http://www.leftlane.pl/sty14/dig-t-r-3-cylindrowy-silnik-nissana-o-wadze-40-kg-i-mocy-400- km.html) holding of a filling object does not work. Everything is always held to upper edge of a screen regardless the settings. Possibility of holding the picture to the bottom edge or center would make my work much easier.
According to UE regulations we have to inform about the cookies. I do not know how to do it in Muse. I mean, when the message shows up one time and is accepted, there would be no need to show it again and again during another visit on the website. Is there any way to do it? Is there any widget for it maybe?
The YouTube widget sometimes changes size just like that. It is so when the miniature of the movie does not load, and the widget is set to stroke (in our case 4 pixels, rounded to 1 pixel). As I remember ( in case of a load error) it extends for 8 pixels wide.
Last but not least - we use the cheapest hosting plan in Business Catalyst. The monthly bandwidth is enough, although we have a lot of pictures and we worried about it at first. Yet we are running out of the disk storage very quickly. We have used more than a half of a 1 GB after a month. We do not want to change BC for a different one, because we like the way it is connected with Muse. But we do not want to buy the most expensive package - but only this one has more disk space. We do not need any other of these functions and it would devastate our budget. Do we have any other option?
I’m using Adobe Muse 7.2 on OS X 10.9.1.
and I'm sending Muse file to <[email protected]>

Unfortunatley, there is no way to get a code view in Muse. I know quite a few people requested it in the previous forum, but not really sure where that ended up. Also, you may not want to bring the html into DW unless you only have 1 or 2 small changes 2 make. Two reasons. First, it isnt backwards compatible, so if you are planning on updating that site in Muse, you will need to make those changes in DW everytime you update. Second, by all accounts the HTML that Muse puts out is not pretty or easy to work with. Unlike you, I am code averse, but there was a lenghty discussion on the previous forum on this topic. I know they were striving to make it better with every release, just not sure where it is at this point.
Dont think I am reading that second question right, but there was a ton of info on that old site. You may want to take a look there, people posted a ton of great unique solutions, so it worth a look.
Here is the link to the old forums- http://support.muse.adobe.com/muse

Few questions about upgrading database

Hi everyone,
greetings of the day
I have few questions about the upgrading database,
In export and import mode
1.can we have new name for the target database,
2.I think we need to create tablespaces ,do we need to create users as well
3.If we are upgrading from 9i to 10g database ,any activity to be perfromed other than creating a new sysaux tablespace
4.How come we get consistent export
In DBUA mode ( in the same machine only)
1.Do we need shutdown / startup restrict the database
2.How can we move the files to the new location
3.Can we change db_name of the database
4.Can we use the old database as well
In manual upgration using catupgrd scripts
1.Can we rename the db_name
2.can we use old database as well
3.how to move the database files to the new location
4.can we perform this kind of upgrade on a different server
5.when we startup upgrade in the new home ,how it identifies the old database in-order to upgrade the old one
Thanks

udayjampani wrote:
Hi everyone,
greetings of the day
Pl post details of source and target database versions, along with your OS details.
I have few questions about the upgrading database,
In export and import mode
1.can we have new name for the target database,Yes.
2.I think we need to create tablespaces ,do we need to create users as wellYou can create users, but it is not necessary. You need to pre-create tablespaces only if their characteristics/locations on the target are different than on the source.
3.If we are upgrading from 9i to 10g database ,any activity to be perfromed other than thisNot that I am aware of - see the steps in the Upgrade Guide - http://docs.oracle.com/cd/B19306_01/server.102/b14238/expimp.htm
4.How come we get consistent export wetherEnsure the database is started in restricted mode, so users will not be able to access the database during the export.
>
In DBUA mode ( in the same machine only)
1.Do we need shutdown / startup restrict the databaseNo - DBUA will do this automatically for you.
2.How can we move the files to the new locationYou can after the upgrade move the datafiles to wherever you want - use the ALTER DATABASE RENAME DATAFILE (http://docs.oracle.com/cd/B19306_01/server.102/b14200/statements_1004.htm#i2082829) command.
3.Can we change db_name of the databaseI do not believe this is possible with DBUA.
4.Can we use the old database as wellNo - the database will be upgraded by DBUA - there is no "old" database.
>
>
In manual upgration using catupgrd scripts
1.Can we rename the db_nameYes.
2.can we use old database as wellNo - the scripts will upgrade the database - there is no "old" database.
3.how to move the database files to the new locationSee above.
4.can we perform this kind of upgrade on a different serverPl elaborate on what you mean by this. You can copy the existing database to a different server (assuming compatible OS) and upgrade it there.
>
>
ThanksHTH
Srini

Question about ghost copy of an old hardrive

Similar Messages

Maybe you are looking for