Question about multiple listeners and vip addresses in rac.

We have a 2 node rac cluster running 10.2.0.3 on rhel4 on the itanium platform. We have a need where we want to connect the 2 hosts up to another network temporarily by configuring an additional network interface on each server so that we can test some connections from a different network.
My question is can you configure multiple listeners on the same server in which the newly added listener can be configured to service requets on the new network interface?
Because it's rac would you need to configure an additional vip address? I am not sure that you can have multiple vip's on a server?
Has anyone configured rac in such a way, any help is appreciated.

can you configure multiple listeners on the same server in which the newly added listener can be configured to service requets on the new network interface?Yes, you can but you should not be doing this. Listener is a node specific resource and one listener can server multiple services. You actually can create multiple services within the database for different set of users and all can be registered to the same listener.
Because it's rac would you need to configure an additional vip address? What do you mean by additional IP?
You have installed 10g RAC where you have already configured virtual IPs. Why do you want to have additional one? node1 - static ip1, vip1, pvtip1
node2 - static ip2 vip2, pvtip2
total 6
I am not sure that you can have multiple vip's on a server?Nothing to do with the server, they are based on public IP. Yes you can create multiples vip's based on same public IP. This is possible, But you do not need to do this in RAC environment.

Similar Messages

[JS] Basic question about event listeners and event handlers

I am very new to the whole topic of event listeners and event handlers. I'd run the test for the following problem myself, but I don't know where to start, and I just want to know if it's impossible -- that is, if I'm misunderstanding what event listeners and event handlers do.
Say I have an InDesign document with a text frame that is linked to an InCopy story. Can I use an "afterImport" event listener on the text frame to perform some action any time the link to the InCopy story gets updated? And will the event handler have access to both the story that is imported, and the pathname of the InCopy file?
Thanks.

Thank you, Kasyan.
Both of those are good solutions.
We are currently using InDesign CS4 and InCopy CS5. I'm hoping to get them to purchase the whole CS5 suite soon, since I'd like to start writing scripts for InDesign CS5 as soon as possible, as long as I'm going to have to be doing it in the not too distant future anyway. The greater variety of event handlers sounds like it might be something that is crucial to the project I'm working on, so that adds to the argument for getting CS5.
Thanks again. You have no idea how helpful this is. I made some promises to my boss yesterday that I later realized were based on assumptions of mine about the InDesign/InCopy system that didn't make any sense, and I was going to have to retract my promises. But after reading your response I think I can still deliver, in a slightly different way that I had been thinking before.
Richard

Want to change Public, private and vip address on RAC 10g R2 windows 2003

The network section told us the configuration of the network who support our cluster will have to change all ip address.
We are looking for a complet document who give all the step by step instructions how to make this change.
We have to change the Public, private and VIP at the same time of our 3 nodes cluster.
We know the OCRCFG will be impact. So we will take backup of it first.
Can someone are able to indicate us how to procede to execute this task.
Thanks

Hi,
i check the Note:283684.1 you give me, but it didn't give all the answers to my problem.
I finally found a recipe to make the job. I would like to tell you it's not supported be Oracle, but it work very well
Don't forget to take a good backup of the ocrcfg and vote disk before you start.
Here we go:
Stop all Oracle service on all nodes before the change of the address, the low format of the ocrcfg and vote disk
change the address in the file host in C:\WINDOWS\system32\drivers\etc with the new address
change the ip address in the window network definition connection with the new address
ocopy \\.\ocrcfg d:\backup\ocrcfg.dmp
ocopy \\.\votedsk1 d:\backup\votedsk1.dmp
rem go to directory of the cluster binary crs\bin
cd /D D:\Oracle\Ora10g\crs/bin
rem Format raw ocrcfg and vote disk
LogPartFormat.exe \\.\ocrcfg /q
LogPartFormat.exe \\.\votedsk1 /q
rem Run in prompt mode the cluster setup
rem crssetup.exe config -nn %s_nodenumberlist% -pn %s_privatenamelist% -ch %ORA_CRS_HOME% -oh %s_OracleHome% -c %s_clustername% -l "%s_languageid%" -q %s_votedisklist% -g %s_usergroup%
rem example for 2 node
crssetup.exe config -nn host_name_node_1 ,1,host_name_node_2,2 -pn host_name_node_1-priv,1,host_name_node_2-priv,2 -ch D:\Oracle\Ora10g\crs -oh D:\Oracle\Ora10g\crs -c crs_lab -l "CANADIAN FRENCH_CANADA.WE8MSWIN1252"; -q "\\.\votedsk1"
rem ensures that all nodes are configured with the same port for the ONS
racgons.exe add_config host_name_node_1:6200 host_name_node_2:6200
rem oifcfg to direct components to use specific network interfaces
oifcfg.exe setif -global "Public"/10.200.5.0:public "Prive"/192.169.255.0:cluster_interconnect
rem to rebuild the vip address vipca in wondow componant and make the incription in the cluster (in prompt mode or online)
rem at the same time it will create the gsd and ons service
vipca.bat -silent -nodelist "host_name_node_1,host_name_node_2" -nodevips "host_name_node_1/host_name_node_1-vip/255.255.255.0/Public,host_name_node_2/host_name_node_2-vip/255.255.255.0/Public";
rem vipca
rem check the state of the crs services (inscription)
crs_stat -t
rem now make the registration of the listener in the cluster.
rem important don't use the prompt command below, it will give you a crs-0223 error at the startup service
Rem to solve this problem use netca on line
rem crs_register ora.host_name_node_1.LISTENER_host_name_node_1.lsnr -dir D:\Oracle\Ora10g\crs\crs\profile
rem crs_register ora.host_name_node_2.LISTENER_host_name_node_2.lsnr -dir D:\Oracle\Ora10g\crs\crs\profile
rem srvctl start nodeapps -n host_name_node_1
ren srvctl start nodeapps -n host_name_node_2
netca
rem check the state of the crs services (inscription)
crs_stat -t
rem start oracle object service and cluster volume before registering and accessing to asm services
sc \\host_name_node_1 start ”Oracle Object Service”
sc \\host_name_node_1 start OracleClusterVolumeService
sc \\host_name_node_2 start ”Oracle Object Service”
sc \\host_name_node_2 start OracleClusterVolumeService
rem go the the rdbms directory to make the registration of asm and the database
set ORACLE_HOME=D:\Oracle\Ora10g\rdbms
rem add the service asm in the cluster in my case asm1 and asm2 for my 2 nodes
srvctl add asm -n host_name_node_1 -i +ASM1 -o %ORACLE_HOME%
srvctl add asm -n host_name_node_2 -i +ASM2 -o %ORACLE_HOME%
rem start the asm service on each node
srvctl start asm -n host_name_node_1
srvctl start asm -n host_name_node_2
rem check the state of the crs services (inscription)
crs_stat -t
rem go to the bin directory of rdbms directory to make the registration of the database
cd /D D:\Logiciels\Oracle\Ora10g\rdbms/bin
rem register the database (in my case labotary lab) and the to database service (lab1 and lab2) of each node
srvctl add database -d lab -o %ORACLE_HOME%
srvctl add instance -d lab -i lab1 -n host_name_node_1
srvctl add instance -d lab -i lab2 -n host_name_node_2
rem finally start the database
srvctl start database -d lab
rem go to directory of the cluster binary crs\bin
rem all the services
cd /D D:\Logiciels\Oracle\Ora10g\crs/bin
rem you can go in the database with sqlplus and check all your components
crs_stat -t
I hope this will help someone who are in the same situation
Edited by: ron_berube on 2008-12-12 09:21
Edited by: ron_berube on 2008-12-12 10:08
Edited by: ron_berube on 2008-12-13 08:25
Edited by: ron_berube on 2008-12-18 10:49

Question about multiple tables and formulas in numbers

I was wondering about having a formula that effects one table based on data in the other table. I have a spreedsheet that i created for work. In column A is a list of addresses. In column B-ZZ is a list of "billing codes" the get applied to the service work done for that address.Its kind of difficult to look at this large spreadsheet on my iphone and edit it on the go. Is there a way to, Have another column, possibly on sheet 2 or something, where i type in these "billing codes" and they would fill an x or some other character in cell that corrisponds with that billing code on that address line? So to be as plain as possible, I want to enter data in one cell (another sheet if possible) and have it "mark" another cell in response to the specific data on that "entry cell." Im thinking this way because instead of scrolling back and fourth on the sheet on my iphone, to "mark" the boxes, i could just navigate to sheet 2 enter the data, or "billing codes" and they would "X" the cell that would match up with the code column and address row. each address row would have a seperate "entry field" in sheet 2, to make the formula easier. thanks for any help

Tom,
That's a lot of columns for jsut a table of marks that reflect an input. Sure, you could have each cell in that giant table check to see if some corresponding cell contains certain text, but that document is going to be slower than you might be able to tolerate.
Jerry

Question about multiple classes and Linked Lists

Lets say you have 4 classes: LinkedList which is the main class, Node, Card, and Hand. im not putting any constructors yet
The card class keeps track of a card such as a king of diamonds:
public class Card {
string suit;
string rank;
the node class has a Card object and another node object so it would be
public class Node {
Card c;
Node next;
the hand class keeps track of the users hand. This program will ask the user if they want to add, remove, print out the hand, or print out the score of the hand, I guess it would be like this
public class Hand {
Node head;
The linkedlist class will contain all the methods for doing the above
now my questions are. Lets say I want to add a card, so I would have to add a new Node which contains the card. If i wanted to access the new nodes card contents, lets call this node g, can i do, g.c.suit and g.c.rank in which this case c is the card object in Node. Also, these are not going to be nested classes, they are going to be 4 seperate classes, if I declare all variables as private will I need to extend the classes or not and if there is a better way, let me know. Thanks alot for all your help and previous help.

here is an example of Card and Hand ...
not saying its good design
but it does work
public class Cards {
public static void main(String[ ] args) {
Card c1 = new Card ("ace", "diamonds");
Card c2 = new Card ("two", "spades");
Card c3 = new Card ("three", "hearts");
Hand a1 = new Hand ();
a1.add(c1);
a1.add(c2);
a1.add(c3);
System.out.println("\nshowing hand ...");
a1.show();
System.out.println("\ndeleting " + c2.num + " " + c2.suite);
a1.del(c2);
System.out.println("\nshowing hand ...");
a1.show();
} // main
} // class
class Hand exists in 3 states
and is designed to be a chain of cards ...
1. when class Hand is first created
   a. it has no card
   b. and no nextHand link
2. when somecard is added to this Hand
   a. it has a card
   b. and the nextHand link is null
3. when somecard is attempted to be added to this Hand
   and it already has a card
   then a nextHand is created
   and the somecard is added to the nextHand
   a. so the Hand has a card
   b. and the Hand has a nextHand
class Hand {
public Card acard;
public Hand nextHand;
public Hand () {
acard = null;
nextHand = null;
public void add (Card somecard) {
if (acard == null) {
    acard = somecard;
    return;
if (nextHand == null) nextHand = new Hand();
nextHand.add (somecard);
delete this Hand by making this Hand
refer to the next Hand
thus skipping over this Hand in the nextHand chain
for example, removing Hand 3 ...
1 - 2 - 3 - 4   becomes
1 - 2 - 4
public void del (Card somecard) {
if (acard == somecard) {
    if (nextHand != null) acard = nextHand.acard;
    else acard = null;
    if (nextHand != null) nextHand = nextHand.nextHand;
    return;
nextHand.del(somecard);
public void show() {
if (acard == null) return;
System.out.println(acard.num + " " + acard.suite);
if (nextHand != null) nextHand.show ();
} // class
class Card {
public String num;
public String suite;
Card (String num, String suite) {
this.num = num;
this.suite = suite;
} // class

Questions about multiple nodes and licenses

Nico, What would be the right forum to ask the licensing questions i stated above? Jimit

I can't and won't discuss license issues, but for the last question (mixing nodes with different operating systems) there's a fairly easy answer why this can lead to all sorts of trouble.Windows and Linux/Unix usually work in different code pages, making it hard to interchange flat files.Text lines in Windows flat files are usually terminated by the two characters Carriage Return followed by Line Feed (0x0D followed by 0x0A) whereas under Linux/Unix text lines are always terminated by Line Feed characters (0x0a) only. Not all Windows and Linux/Unix programs can handle this difference without trouble.Very often Windows and Linux/Unix machines run with difference 8-bit code pages for the nodes themselves. This means that all sorts of diacritics (such as German Umlaute ä, ö, ü, ß) may be processed by programs on both platforms in different ways.Shell scripts and batch files resp. all sorts of operating system commands are very much incompatible between these systems, making it almost impossible (ok, just extremely difficult) to write scripts running on both system worlds.Last not least Integration Services in a server grid must be of the same operating system and run in the same code page, meaning that these two nodes will never be able to be part of the same server grid. That's just what came to my mind within a few seconds of thinking. Regards,Nico

Question About Color's and Gradients

Hi all,
I have a question about color swatches and gradients.
I am curious to know, if I have 2 color swatches that I make into a gradient color, is it posible to change the tint of each indivdual color in that gradient and have that applied to the gradient without having to adjust the gradients opacity.
The reason that I'm asking this is because in creating a project I found that the colors that I chose for to make my gradient from my swatches were to dark, and while I can adjust each one's tint to my liking (if the object they were applied to was going to be a solid color) but that doesn't seem to apply to the overall gradient.
I hope that makes sense, I know that this was something that was able to be accomplished in quark and was wondering if I can do something similar.

If you double click your gradient swatch (after adding it to the swatches)
Then click a colour stop in the gradient, and then change the drop down menu to CMYK (or rgb)
And you can alter the percentages there. It's not much use for spot colours but it's a start.
But making tint swatches would be a good start anyway.
At least then when you double click the gradient (in the swatches) to edit it you can choose from CMYK, RGB, LAB, or Swatches and adjust each colour stop to your liking.

Question about clear page and reset pagination

Hi,
I have a question about clear pages and the reset pagination in an URL. What is the reason why a clear page doesn't also trigger a reset pagination on the pages which are cleared?
I can't really imagine a business case where it makes sense to clear all data of page items on a page and don't reset the pagination of reports on that page which probably use a page item in there where clause...
The drawback of this behavior is that a developer always has to set the reset pagination checkbox when he clears the target page and the even bigger drawback is that if you specify other pages to clear, you can't reset pagination for them, because reset pagination only works for the target page.
Thanks for your input.
Patrick
*** New *** Oracle APEX Essentials *** http://essentials.oracleapex.info/
My Blog, APEX Builder Plugin, ApexLib Framework: http://www.oracleapex.info/

Enhancement request filed, thanks,
Scott

The question about portlet customization and synchronization

I have a question about portlet customization and synchronization.
When I call
NameValuePersonalizationObject data = (NameValuePersonalizationObject) PortletRendererUtil.getEditData(portletRenderRequest);
portletRenderRequest.setPortletTitle(str);
portletRenderRequest.putString(aKey, aValue);
PortletRendererUtil.submitEditData(portletRenderRequest, data);
Should I make any synchronization myself (use "synchronized" blocks or something else) or this procedure is made thread-safe on the level of the Portal API?

HI Dimitry,
I dont think you have to synchronize the block. i guess the code is synchronized internally.
regards,
Harsha

A question about item "type and release" of source system creation

Hello expert,
I have a question about item "type and release" of source system creation.
As we know,when we create a web servie source system,there will display a pop-up which includes three items as "logical system","source system"and "type and release".
About the item "type and release",when we push "F4" button,there will be three default selections as below:
"ORA 115     Oracle Applications 11i
TLF 205     Tealeaf 2.05B
XPD 020     SAP xPD".
Who can tell me when and how should I use the three selections.
And also I attempted to input the item by some optional letters except the default three selections and it seems that I can input it freely.
Thank you and Best Regards,
Maggie

Hello DMK,
Thank you very much for your answer.It is very helpful for me.
Can I ask you further about it?
I got that it is a semantic description item.
You said the default selections are set by our basis people.Would you like to tell me how should we creat a new value except the default ones for item "type and release"?Only by inputing the value in the item directly?But you see we canot see the new value item we created by ourself when we push "F4" button next time ,is that ok?Or do we have to ask basis people to define one new value item just like the default seletions before we use it.
Also if possible would you like to describe detail about "This becomes important when you are troubleshooting certain issues especially when RFC connection problems."
Thank you and Best Regards,
Maggie
Message was edited by: Maggie

A few questions about the ka790gx and dka790gx

i have a few questions about the ka790gx and dka790gx , how much better is the dka790gx compaired to the ka790gx ? . how much difference does the ACC function make to overclocking etc , i plan on getting a phenom II 940BE or 720BE . i already have the ka790gx so would it be worth building another system using the dka790gx mobo , or should i keep what i already have and just change the cpu ?

It's largely irrelevant what other boards had VRM issues other than the KA790GX - the fact is it died at stock settings. Since there is little cost difference between the more robust DKA790GX (or Platinum if you really need 1394) why bother with the proven weakling? There are other examples around of the KA not having a robust power section. There's no way I would use even a 95W TDP CPU in the KA and absolutely not O/C.....!
As for the credentials of Custom PC, I have generally found their reviews accurate and balanced, and echo my own findings where applicable. If a little too infrequent.
The fact that the KA has such a huge VRM heatsink leads me to my other comments on the Forum, particularly regarding the "fudge" aspect:
"""Henry is spot on - the notion that adding a heatsink to the top of the D2PAK or whatever MOSFETS is effective is virtually worthless. The device's die thermal junction is the tab on the device back - which is always against the PCB pad. The majority of heat is therefore dissipated in to the board, and the fact that the epoxy plastic encapsulation gets hot is simply due to the inability of the heat to be conducted away from the device die via the tab. Not sure when Epoxy become an effective conductor of heat.... Good practice is to increase the size of the PCB pad (or "land" in American) such that the enlarged PCB copper area acts as an adequate heatsink. This is still not as effective as clamping a power device tab to an actual piece of ali or copper, but since the devices used are SMD devices, this is not possible. However, the surface area required to provide sufficient PCB copper area to act as a heatsink for several devices isn't available in the current motherboard layouts. Where industrial SBC designs differ in this respect is to place the VRM MOSFETs on the back of the PCB on very enlarged PCB pads - where real estate for components is not an issue.
Gigabyte's UD3 2oz copper mainboards sound like a good idea, on the face of it. However, without knowing how they have connected the device tabs to where and what remains a mystery. I suspect it is more hype than solution, although there will be some positive effect. From an electrical perspective, having lower resistance connecting whatever to whatever (probably just a 0V plane) is no bad thing.
The way the likes of ASUS sort of get round the problem is to increase the sheer number of MOSFET devices and effectively spread the heat dissipation over a larger physical area. This works to a degree, there is the same amount of heat being dissipated, but over several more square inches. The other advantage of this is that each leg of the VRM circuit passes less current and therefore localised heat is reduced. Remember that as well as absolute peak operating temperature causing reduced component life, thermal cycling stresses the mechanical aspects of components (die wire bonds for example) as well as the solder joints on the board. Keeping components at a relatively constant temperature, even if this is high (but within operating temperature limits), is a means of promoting longevity.
For myself, the first thing I do with a seperate VRM heatsink is take it off and use a quiet fan to blow air on to the VRM area of the PCB - this is where the heat is. This has the added benefit of actively cooling the inductors and capacitors too....
Cooling the epoxy component body is a fudge. If the epoxy (and thus any heatsink plonked on top of it) is running at 60C, the component die is way above that.....
It's better than nothing, but only just."""

General question about iTunes Match and multiple libraries

Hello to everyone,
I have a general question about the iTunes Match service, which is available since yesterday in my country (Italy). Currently my library situation is the following:
Computer A (desktop, Windows 7): "big" iTunes library (about 20 GB), at the moment not associated with my Apple ID
Computer B (MacBook Air 2011): "small" iTunes library (about 5 GB), associated with my Apple ID
At the moment, both my iOS devices (iPhone 4 and iPad 2) are synchronized with the smaller library on the MacBook Air.
Question is as follows: should I subscribe to iTunes Match, would it be possible to upload the "big" library (provided I associate it with my Apple ID) to iCloud while keeping my devices synchronized with the "small" one?
Ideally, at the end of the day, the situation should be the following: both iOS devices with music from the small library + possibility of downloading songs from iCloud (coming from the big one). Is this possible?
Maybe the question sounds stupid, but I want to be sure about this before paying for the service.
Thanks a lot.

Yes, you could also associate your larger library with iTunes match if you associated your Apple ID with it. However any purchases in the library made from another Apple ID will not be matched with iTunes much.
If both libraries are part of iTunes match, then all your devices will see all of the content from both libraries, which content you choose to have on those devices and which you have accessible via iTunes match is entirely up to you.

Few questions about apex + epg and cookie blocked by IE6

Hi,
I would like to ask a few questions about apex and epg.
I have already installed and configured apex 3.2 on oracle 10g (on my localhost - computer name 'chen_rong', ip address -192.168.88.175 ), and enable anonymous access xdb http server.
now,
1. I can access 'http://chen_rong' , 'http://localhost' , 'http://192.168.88.175' without input username / password for realm 'XDB' in IE6;
2. I can access 'http://localhost/apex/apex_admin' , 'http://192.168.88.175/apex/apex_admin' , and I can be redirected into apex administation page after input admin/<my apex admin password> for realm 'APEX' in IE6;
3. I can access 'http://chen_rong/apex/apex_admin' in IE6, but after input admin/password , I can not be redirected into administation page, because the cookie was blocked by IE6.
then, the first question is :
Q1: What is the difference among 'http://chen_rong' , 'http://localhost' , 'http://192.168.88.175' ? I have already include site 'chen_rong' into my trusted stes! why the cookie was blocked by IE6. I have already tried firefox and google browser, both of them were ok for 'chen_rong', no cookie blocked from site 'chen_rong'!
and,
1. I have tried to use the script in attachment to test http authentication and also want to catch the cookie by utl_http .
2. please review the script for me.
3. I did:
SQL> exec show_url('http://localhost/apex/apex_admin/','ADMIN','Passw0rd');
HTTP response status code: 401
HTTP response reason phrase: Unauthorized
Please supplied the required Basic authentication username/password for realm XDB for the Web page.
Web page http://localhost/apex/apex_admin/ is protected.
MS-Author-Via: DAV
DAV: 1,2,<http://www.oracle.com/xdb/webdav/props>
Server: Oracle XML DB/Oracle Database
WWW-Authenticate: Basic realm="XDB"
Date: Tue, 04 Aug 2009 02:25:15 GMT
Content-Type: text/html; charset=GBK
Content-Length: 147
======================================
PL/SQL procedure successfully completed
4. I also did :
SQL> exec show_url('http://localhost/apex/apex_admin/','ANONYMOUS','ANONYMOUS');
HTTP response status code: 500
HTTP response reason phrase: Internal Server Error
Check if the Web site is up.
PL/SQL procedure successfully completed
SQL> exec show_url('http://localhost/apex/apex_admin/','SYSTEM','apexsite');
HTTP response status code: 401
HTTP response reason phrase: Unauthorized
Please supplied the required Basic authentication username/password for realm APEX for the Web page.
Web page http://localhost/apex/apex_admin/ is protected.
Content-Type: text/html
Content-Length: 147
WWW-Authenticate: Basic realm="APEX"
======================================
PL/SQL procedure successfully completed
my second questions is :
Q2: After I entered into realm 'XDB', I still need went into realm'APEX'. how could I change the script show_url to accomplish these two tasks and successfully get the cookie from site.
the show_url script is as following:
CREATE OR REPLACE PROCEDURE show_url
(url IN VARCHAR2,
username IN VARCHAR2 DEFAULT NULL,
password IN VARCHAR2 DEFAULT NULL)
AS
req UTL_HTTP.REQ;
resp UTL_HTTP.RESP;
name VARCHAR2(256);
value VARCHAR2(1024);
data VARCHAR2(255);
my_scheme VARCHAR2(256);
my_realm VARCHAR2(256);
my_proxy BOOLEAN;
cookies UTL_HTTP.COOKIE_TABLE;
secure VARCHAR2(1);
BEGIN
-- When going through a firewall, pass requests through this host.
-- Specify sites inside the firewall that don't need the proxy host.
-- UTL_HTTP.SET_PROXY('proxy.example.com', 'corp.example.com');
-- Ask UTL_HTTP not to raise an exception for 4xx and 5xx status codes,
-- rather than just returning the text of the error page.
UTL_HTTP.SET_RESPONSE_ERROR_CHECK(FALSE);
-- Begin retrieving this Web page.
req := UTL_HTTP.BEGIN_REQUEST(url);
-- Identify yourself.
-- Some sites serve special pages for particular browsers.
UTL_HTTP.SET_HEADER(req, 'User-Agent', 'Mozilla/4.0');
-- Specify user ID and password for pages that require them.
IF (username IS NOT NULL) THEN
UTL_HTTP.SET_AUTHENTICATION(req, username, password, 'Basic', false);
END IF;
-- Start receiving the HTML text.
resp := UTL_HTTP.GET_RESPONSE(req);
-- Show status codes and reason phrase of response.
DBMS_OUTPUT.PUT_LINE('HTTP response status code: ' || resp.status_code);
DBMS_OUTPUT.PUT_LINE
('HTTP response reason phrase: ' || resp.reason_phrase);
-- Look for client-side error and report it.
IF (resp.status_code >= 400) AND (resp.status_code <= 499) THEN
-- Detect whether page is password protected
-- and you didn't supply the right authorization.
IF (resp.status_code = UTL_HTTP.HTTP_UNAUTHORIZED) THEN
UTL_HTTP.GET_AUTHENTICATION(resp, my_scheme, my_realm, my_proxy);
IF (my_proxy) THEN
DBMS_OUTPUT.PUT_LINE('Web proxy server is protected.');
DBMS_OUTPUT.PUT('Please supply the required ' || my_scheme ||
' authentication username/password for realm ' || my_realm ||
' for the proxy server.');
ELSE
DBMS_OUTPUT.PUT_LINE('Please supplied the required ' || my_scheme ||
' authentication username/password for realm ' || my_realm ||
' for the Web page.');
DBMS_OUTPUT.PUT_LINE('Web page ' || url || ' is protected.');
END IF;
ELSE
DBMS_OUTPUT.PUT_LINE('Check the URL.');
END IF;
-- UTL_HTTP.END_RESPONSE(resp);
-- RETURN;
-- Look for server-side error and report it.
ELSIF (resp.status_code >= 500) AND (resp.status_code <= 599) THEN
DBMS_OUTPUT.PUT_LINE('Check if the Web site is up.');
UTL_HTTP.END_RESPONSE(resp);
RETURN;
END IF;
-- HTTP header lines contain information about cookies, character sets,
-- and other data that client and server can use to customize each
-- session.
FOR i IN 1..UTL_HTTP.GET_HEADER_COUNT(resp) LOOP
UTL_HTTP.GET_HEADER(resp, i, name, value);
DBMS_OUTPUT.PUT_LINE(name || ': ' || value);
END LOOP;
-- Read lines until none are left and an exception is raised.
--LOOP
-- UTL_HTTP.READ_LINE(resp, value);
-- DBMS_OUTPUT.PUT_LINE(value);
--END LOOP;
UTL_HTTP.GET_COOKIES(cookies);
dbms_output.put_line('======================================');
FOR i in 1..cookies.count LOOP
IF (cookies(i).secure) THEN
secure := 'Y';
ELSE
secure := 'N';
END IF;
-- INSERT INTO my_cookies
-- VALUES (my_session_id, cookies(i).name, cookies(i).value,
-- cookies(i).domain,
-- cookies(i).expire, cookies(i).path, secure, cookies(i).version);
dbms_output.put_line('site:'||url);
dbms_output.put_line('cookies:');
dbms_output.put_line('name:'||cookies(i).name);
dbms_output.put_line('value:'||cookies(i).value);
dbms_output.put_line('domain:'||cookies(i).domain);
dbms_output.put_line('expire:'||cookies(i).expire);
dbms_output.put_line('path:'||cookies(i).path);
dbms_output.put_line('secure:'||secure);
dbms_output.put_line('version:'||cookies(i).version);
END LOOP;
UTL_HTTP.END_RESPONSE(resp);
EXCEPTION
WHEN UTL_HTTP.END_OF_BODY THEN
UTL_HTTP.END_RESPONSE(resp);
END;
/

I use oracle database enterprise edtion 10.2.0.3. I have already figured out the epg on 10.2.0.3 to support apex 3.2.
And as I described above, the apex site works fine for ip address , and localhost. but the cookie will be blocked by IE6, if I want to access the site by 'http://computername:port/apex/apex_admin'. This problem does not occured in firefox and google browser. Could someone give me answer?

Some basic questions about foriegn key , and relationships.

Hi
Thank you for reading my post
I read some documents about foreugn key and tables relation ships.
but i still can not understnad some stuff.
1-when we have a foreign key , we have two tables that we want to relate them together
in a way that one of ? table columns forced to be a value from ?? table column.
what is name of those two tables , i saw , child-parent , ..... which confuse me.
can some one please tell me correct name of those two tables ?
2-some times we need some kind of master details relation like :
one-to-many : i this case MANY table will have a column to point a record in ONE table , can this relation be a foreign key relation ?
3-we can achieve many-to-many relation only by using a helper table to host both tables primary keys in a record to relate them together.
can you point me to some resources that help me to find answers to this questions ?
or explain them to me ?
thank you for your time.

These are critical database basics that you need to understand. I would seriously recommend getting some study in, because proper relational database design relies on the basic principle of data and relationships and a process called normalization.
In reality, you only really need one gigantic table to host data. It would include everything you would want to know about something - let's take a sales order for example. You would have to record the customer's name, address, etc. along with every item they ordered, etc. You would have a HUGE table full of data that appeared over and over and over again. This is bad design for two basic reasons: it is difficult to query, and it is very easy to have minor mistakes like capitalization or alternate spellings that prevent things from matching up properly. For example, let's say Bob orders 40 widgets and 40 digits. In our hypothetical table, we could put it in as Bob - 40 widgets and Robert - 40 digits. See how confusing this can get even in a simple example? And let's say you wanted to correct all of Robert's orders to say Bob and you found out there were 40 orders from "Robert" How would you know which ones to change?
The process of normalization helps to reduce the chance for these types of errors in addition to creating a good basis for indexes. You normalize the data by creating sets of parent/child tables with a "key" value to match them. In our hypothetical situation, you could create a table for orders and a table for customers. In the customers table you give all the detail for the customer in one place, and you assign each customer a unique number or ID. In the orders table we add the customer ID (NOT the name) and we ensure that we are getting the customer we want, in addition to saving a lot of space and eliminating redundancy. In our example, the customers table is the "parent" table and the orders table is the "child" table. The child table references the unique entries in the parent table via that id. That reference is referred to as a foreign key. The foreign key in the child table points back to the original and complete record in the parent table and eliminates the redundancy of keeping all that extra data for every order. Foreign keys in child tables always refer to a primary/unique key in the parent field.
That help?

Question about dependent projects (and their libraries) in 11g-Oracle team?

Hello everyone,
I have a question about dependent projects. An example:
In JDeveloper 10.1.3.x if you had for instance 2 projects (in a workspace): project 1 has one project library (for instance a log4j library) and project 2 is a very simple webapplication which is dependent on project 1. Project 2 has one class which makes use of log4j.
This compiles fine, you can run project 2 in oc4j, and the libraries of project 1 (log4j) are added on the classpath and everything works fine. This is great for rapid testing as well as keeping management of libraries to a minimum (only one project where you would update a library e.g.)
However in 11g this approach seems not to work at all anymore now that weblogic is used, not even when 'export library' is checked in project 1. The library is simply never exported at all - with a noclassdeffound error as result. Is this approach still possible (without having to define multiple deployment profiles), or is this a bug?
Thanks!
Martijn
Edited by: MartijnR on Oct 27, 2008 7:57 AM

Hi Ron,
I've tried what you said, indeed in that .beabuild.txt when 'deploy by default' is checked it adds a line like: C:/JDeveloper/mywork/test2/lib/log4j-1.2.14.jar = test2-view-webapp/WEB-INF/lib/log4j-1.2.14.jar
Which looks fine, except that /web-inf/lib/ is empty. I presume its a sort of mapping to say: Load it like it in WEB-INF/lib? This line is not there when the deploy by default is not checked.
I modified the TestBean as follows (the method that references Log4j does it thru a Class.forName() now only):
public String getHelloWorld() {
try {
Class clazz = Class.forName("org.apache.log4j.Logger");
System.out.println(clazz.getName());
catch(Exception e) {
e.printStackTrace();
return "Hello World";
In both cases with or without line, it throws:
java.lang.ClassNotFoundException: org.apache.log4j.Logger
     at weblogic.utils.classloaders.GenericClassLoader.findLocalClass(GenericClassLoader.java:283)
     at weblogic.utils.classloaders.GenericClassLoader.findClass(GenericClassLoader.java:256)
     at weblogic.utils.classloaders.ChangeAwareClassLoader.findClass(ChangeAwareClassLoader.java:54)
     at java.lang.ClassLoader.loadClass(ClassLoader.java:306)
     at java.lang.ClassLoader.loadClass(ClassLoader.java:251)
     at weblogic.utils.classloaders.GenericClassLoader.loadClass(GenericClassLoader.java:176)
     at weblogic.utils.classloaders.ChangeAwareClassLoader.loadClass(ChangeAwareClassLoader.java:42)
     at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:319)
     at java.lang.Class.forName0(Native Method)
     at java.lang.Class.forName(Class.java:169)
     at nl.test.TestBean.getHelloWorld(TestBean.java:15)
Secondly I added weblogic.xml with your suggested code, in the exploded war this results in a weblogic.xml which looks like:
<?xml version = '1.0' encoding = 'windows-1252'?>
<weblogic-web-app xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://www.bea.com/ns/weblogic/weblogic-web-app.xsd" xmlns="http://www.bea.com/ns/weblogic/weblogic-web-app">
<container-descriptor>
<prefer-web-inf-classes>true</prefer-web-inf-classes>
</container-descriptor>
<jsp-descriptor>
<debug>true</debug>
<working-dir>/C:/JDeveloper/mywork/test2/view/classes/.jsps</working-dir>
<keepgenerated>true</keepgenerated>
</jsp-descriptor>
<library-ref>
<library-name>jstl</library-name>
<specification-version>1.2</specification-version>
</library-ref>
<library-ref>
<library-name>jsf</library-name>
<specification-version>1.2</specification-version>
</library-ref>
</weblogic-web-app>
The only thing from me is that container-descriptor tag, the rest is added to it during the deployment. Unfortunately, it still produces the same error. :/ Any clue?

Question about multiple listeners and vip addresses in rac.

Similar Messages

Maybe you are looking for