Question about setting up rdp using a cisco 800 series router

HI there,
I am currently in school for networking. One co-op placement I went too handed me a cisco 800 series router to practice my routing skills on. I am trying to setup RDP so I can access my server from outside my internal network. I ran this following acl command to do it.
ip nat inside source static tcp server IP address port# cable modem IP port # extendable.
My question here is, my cable modem will occasionally hand out a different IP since it has DCHP. I cannot turn DHCP off in my cable modem. So is there a way I can set this up to use a dynamic IP from my modem so I alwasy have access to it or every time my modem changes the IP address do I have to go in and modify this acl?

Configure DDNS ( Dynamic DNS ) on the router. For this you need to register with a DDNS provider. Go to
http://www.no-ip.com/ . they provide free reliable service.
With DDNS, Once your router gets a DHCP address from your ISP , it will dynamically update the DNS name record. For example if you register you routers name as, "myrouter.no-ip.org", from there onwards whatever the IP your router gets, you can refer to that by this name.
So do as what Paolo said regarding using interface instead of ip, and register with the DDNS and you are good to go..
Hope this helps
Please rate this post if helpful..
Thanks
Shamal

Similar Messages

A zillion questions about setting up and using external hard drive

Hello. I recently purchased a Cavalry 440GB CACE USB/FW800 7200 RPM 3.5 in Mac Formatted hard drive. My Mac is a Power PC G4 using OS X 10.2.8.
After much back and forth with the Cavalry support desk, I was able to connect it to my Mac. (The USB cable included was not compatible--fortunately, my printer cable was.)
Through Disk Utility I see that my Mac is detecting the hard drive, but there's no icon on my desktop. My questions are as follows:
1. How do I get the icon on my desktop?
2. It was suggested on this board to partition the hard drive. What exactly is partitioning, and is it necessary?
3. If I do partition the hard drive, into how many partitions should I make it?
4. Once the number of partitions is set, can that number be changed? In other words, can it be repartioned without erasing anything?
5. My main purpose for getting the external hard drive is to move all my movies off my Mac. I'm sure I will want to back up other files as well. Should I create one partition for all the movies, and one for photos, one for files, etc.?
6. Once I get the icon on my desktop, is transferring files as simple as dragging the files onto the icon?
7. Once I move files to the hard drive, is it simple to move them back to the Mac if I need to use them again?
OK, that's all for now. I appreciate your patience in dealing with all my questions! Thanks.

Hello,
I'll try my best on the first seven. The remaining zillion minus seven questions will have to wait!
1. If the drive really is Mac-formatted it should just appear. Firstly check that hard disks are set to appear on the desktop. In the Finder go to Finder > Preferences... >General tab and ensure that the box to show hard disks on the desktop is checked. If that doesn't work go to Macintosh HD > Applications > Utilities >Disk Utility. Select the drive in the left hand pane and then click on the "Erase" tab. Erase the disk and ensure the format is "Mac OS Extended (with Journalling)".
2. Partitioning is splitting the physically drive into two or more volumes. This will allow you to compartmentalise your data. You will have two or more icons appear on the desktop if you do partition. Although they are on the same physical disk you will be limited on each of the volumes to the size you set at the time of partitioning. If you do partition the drive be sure to use the "Apple Partition Map" not "GUID Partition Map". The latter is for Intel Macs.
3. Whatever you want. My experience is that too many partitions and you loose flexibility in your storage space. Personally on my external drive I have a partition that is exactly the same size as my internal hard drive. I then use that to do a regular clone backup. I then have a second partition for general use. This means I can put files on the external but still guarantee I have enough spare to backup fully.
4. No. Not without third party tools.
5. As I said above, in my opinion the best use is to create a partition for backup and a partition for all other use.
6. Yes absolutely. However if you plan on moving libraries like iTunes or iPhoto then you'll need to show the applications where the libraries are again.
7. Yes.
Some extra pointers:
A. Use Carbon Copy Cloner to backup your internal drive to the external. Clones are fantastic backups as even if the internal drive bursts into flames you will have an identical copy of all user data and settings: http://www.bombich.com/software/ccc.html (scroll to the very bottom for the version suitable for 10.2.8).
B. Don't use USB to connect the hard drive it's not very fast. Firewire 400 is significantly faster and will allow the iMac to be booted from the external drive in an emergency (USB will not boot a G4 Mac).
Hope that helps a little.
mrtotes

Newbie question about setting up a wireless USB device as a router.

Hi. I have this Nintendo Wi-Fi USB Connector, which used to be very useful for getting my DS and Wii online (I don't have a wireless router.)
By using some modified drivers from Buffalo I think, I eventually manage to install it as an ordinary wireless device and later set it up as an all-purpose wi-fi router device. I want to do exactly this in Arch if possible.
As far as I know, there are no real drivers for this device, but I tried some, and got stuck later on.
I basically want to simply be able to use my laptop, PS3, Wii and DS on it. Nothing fancy, and no encryption, as I only use it when necessary.
After plugging the device in the USB, I ran
$ hwdetect --show-net
NET : forcedeth ppp_generic slhc mac80211 rfkill rt2500usb rt2x00lib rt2x00usb cfg80211
I looked like it's was quite ordinary actually. So I tried modprobing rt2500usb (should I modprobe the 2 others too?).
Surprise, surprise! I haven't edited my /etc/rc.conf at all yet.
$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11g ESSID:""
Mode:Managed Channel:0 Access Point: Not-Associated
Tx-Power=0 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Well, at least it detected my wlan. I haven't been able to test if I can actually get online with this thing as there is no network to try on around here.
So, where do I go from here? The KISS way, if you know what I mean, hehehe
- Thanks in advance.
This is my ifconfig -a if useful:
eth0 Link encap:Ethernet HWaddr 00:1D:60:87:18:D5
inet addr:10.0.0.2 Bcast:10.0.0.255 Mask:255.255.255.0
inet6 addr: fe80::21d:60ff:fe87:18d5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2783 errors:0 dropped:0 overruns:0 frame:0
TX packets:2272 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2401773 (2.2 Mb) TX bytes:450333 (439.7 Kb)
Interrupt:23 Base address:0x6000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:280 (280.0 b) TX bytes:280 (280.0 b)
wlan0 Link encap:Ethernet HWaddr 00:0D:0B:C3:18:F2
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wmaster0 Link encap:UNSPEC HWaddr 00-0D-0B-C3-18-F2-00-00-00-00-00-00-00-00-00-00
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Checked around, and I need master mode to be able to do this, however, the drivers I have don't support it :\ Any way to get better drivers somehow?:p
Last edited by Themaister (2008-08-08 06:41:30)

Thank you. Got a bit further, but probably not in the right direction : [
Figured out that the WFC uses the rt2570 chipset (according to wikipedia), which I downloaded from the link you gave. Installed it, and had to blacklist the other ralink-modules that were present for it to work.
Now, my iwconfig looks like this:
lo no wireless extensions.
eth0 no wireless extensions.
rausb0 RT2500USB WLAN ESSID:"" Nickname:""
Mode:Monitor Frequency=2.412 GHz Bit Rate=11 Mb/s
RTS thr:off Fragment thr:off
Link Quality=0/100 Signal level:-120 dBm Noise level:-82 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Well, it apperaently did something.
By looking at the lsmod it only shows up the rt2570.
Well, sudo iwconfig rausb0 mode master returns the same error I had ... :[
Does this mean I'm screwed? xD
EDIT: The forums on that site suggested that the master mode was disabled in the legacy drivers (and the other drivers for that matter) :[
Well, dual boot here we go
Last edited by Themaister (2008-08-10 19:48:36)

Can I terminate 40 Mbps DSL BROAD BAND connection in Cisco 800 series routers

Dear all,
Can I terminate 40 Mbps DSL BROAD BAND connection in Cisco 800 series router?.It is not a leased line.
Which Router model is best for 40 Mbps DSL Broad band termination ?
Thanks&Regards
Ajay Jose K

Hi ,
Below link provides you all model in 800 series .
http://www.cisco.com/c/en/us/support/routers/800-series-routers/tsd-products-support-series-home.html
For your requirement below model should suffice .
Complete throughput from the router is 51 Mbps .
Cisco C891FW Integrated Services Router
HTH
Sandy

Question about Setting Window Title/the use of AVWindowSetTitle()

Hi everyone,
I have a question about setting the title of the window in which the Acrobat viewer normally opens a PDF file. The documentation states that AVWindowSetTitle() cannot be used in this case. However, using it has worked with versions of Acrobat/Reader up until and including version 8.
Everything breaks down starting with Acrobat 9.
According to the documentation I am supposed to do the following: "To set the title of a window in which the Acrobat viewer opens a PDF file, you must replace AVDocOpenFromASFileWithParams() and pass the window title in tempTitle."
Unfortunately, there are 2 problems I have with this approach:
     I do need to be able to change the document title on document Save, not only on document Open
     I do not know what AVDocOpenFromASFileWithParams() implementation has to look like if I have to replace it using HFTReplaceEntry().
Is there a sample customized implementation of AVDocOpenFromASFileWithParams() somewhere that I could take a look at?
Is there a way to change a document Title inside Acrobat/Reader window after a Save operation?
Thanks a million,
Lana2010K

     I am sorry. I don't know how you tested this and came to conclusion that this works correctly in Acrobat X.
     I just tested our Acrobat plug-in with a trial version of Acrobat X and this did not work.
     When we open a file in Acrobat (doing it ourselves in the plug-in by adding another specialized open) we set the window title to something different from the default file name. Then if a file gets edited and saved (File->Save), the window title gets reset to the file name. In the PDDocDidSave callback we call AVWindowSetTitle() to set it back to a more descriptive window title we need. This has worked up until and including Acrobat 8, but does not work in either version 9.0 or 10.0.
     Also, I just modified the plug-in code to always change the Window Title of every document (even if opened through native File->Open) on document Save. It does not work.
     Please help,
          Lana2010K

Question about setting cookies and custom authentication

I have a question about setting cookies.
I have two different 'projects' in HTMLDB - we will call them App1 and App2.
I also have two different connection configurations setup in the DADs.conf file. - we will call them Connect1 and Connect2.
App1 is setup to use database authentication (no user is specified in the DAD) and uses Connect1. Once the user successfully logs in, we set a username cookie (this is a persistent connection).
We created a custom authenticatoin scheme for App2 - this scheme checks for the username cookie (set by App1). We would like for App2 to use Connect2 (HTMLDB_PUBLIC_USER is the default user specified and it uses connection pooling).
Is it possible to set a cookie from App1, Connect1 for App2, Connect2 - then redirect to App2 and pick up that cookie?
Here is an example of what we are trying to accomplish:
A user loggs into App1, we set a cookie, and the user is redirected to App2. If the cookie exists, we allow them access to the home page in App2, if no cookie, we redirect back to a 'Login Failed' page in App1. We don't want App2 to use the same database connection as App1 though, we need App2 to use connection pooling.
Is this possible? OR...Is there a better way to accomplish what we want to do?
This is an enhancement to an existing app. Our requirements are to use Database Authentication (setup where pass expires after 60 days or so, cannot reuse last 3 passwords, etc.) - which is already setup and being used by other applications in our organization. All of our users have accounts in the database. We don't want users to have a new username/pass - and we don't want to manage a separate group for HTMLDB apps.
The existing application uses HTMLDB's built in authentication - which uses database username/pass, and it uses connection pooling, but we cannot handle the pass expire stuff in it, unless there's something we're not seeing or understanding - at least that's how our DBA explained it to us.
Any help with this will be appreciated so much. I can send you the code we have if needed.
Thanks!

Same problem here. I have so many problems with this remote app. Is there an iTunes API? I would like to write my own remote app that actually works.

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
My questions are How do you direct this utility to point to the desktop or the TFTP folder
does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
My router is suppose to have 10.0.0.3 255.0.0.0
Gateway of 10.0.0.1 255.0.0.0
My TFTP Server 10.0.0.2 255.0.0.0
How do I get the MAC address of the Router or the TFTP Server and which one is required?
my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
=====================================================================================
rommon 10 >
rommon 10 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
?=0
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=
rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
rommon 12 > TFTP_CHECKSUM=0
rommon 13 > SET
monitor: command "SET" not found
rommon 14 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
?=0
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
rommon 15 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 16 >       " not found
rommon 17 >FE_SPEED_MODE=2
variable name contains illegal (non-printable) characters
rommon
rommon 18 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
?=0
rommon 19 > tftpdnld [ur]
usage: tftpdnld [-hr]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
            IP_ADDRESS: The IP address for this unit
        IP_SUBNET_MASK: The subnet mask for this unit
       DEFAULT_GATEWAY: The default gateway for this unit
           TFTP_SERVER: The IP address of the server to fetch from
             TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
          TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
      TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
          TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
         TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
          TFTP_MACADDR: The MAC address for this unit
               FE_PORT: 0= (default), 1
         FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                        5=Auto (default)
      TFTP_DESTINATION: The flash destination device for the file
                        flash:(default), usbflash0:, usbflash1:
Command line options:
   -h: this help screen
   -r: do not write flash, load to DRAM only and launch image
rommon 20 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 21 >

What I notice in the original post is this error
ARP: address resolution for 10.0.0.2 timed out.
which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
HTH
Rick

License on the Cisco 3900 Series router.

I am trying to understand what does the "data" license exactly do on the Cisco 3900 series router. What I understood is that the data license supports "MPLS.ATM. Multiprotocol support".
Question is is a do not have this license will I not be able to run BGP, EIGRP and terminate service provider links?
Technology Package License Information for Module:'c3900e'
Technology    Technology-package                  Technology-package
              Current              Type           Next reboot
ipbase        ipbasek9             Permanent      ipbasek9
security      securityk9           Permanent      securityk9
uc            None                 None           None
data          None                 None           None
NtwkEss       None                 None           None
CollabPro     None                 None           None
Configuration register is 0x2102
Thanks,
Nik

I think WAAS express is one of the technologies you will lose out on. Amongst other advanced features. See link below.
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/software-activation-on-integrated-services-routers-isr/white_paper_c11_556985.html
EDIT: And performance routing.

NetConfig issue wrt Cisco 3900 Series Router

Hi Cisco;
I can't able to configure my Cisco 3900 series Router via NetConfig tool. While I am able to Configure all other Routers (7600, & 2800) and Switchs (6500, 3700, 3560). I can accessable 3900 Series Router via Inventory Collection, Sync Archieve, Campus Manager, DFM and etc.
I have Cisco LMS 3.2 with RME 4.3 & using SNMPV3.
Thanks for your support.
Best regards;
Shoaib Ahmed

Hi Clarke;
Please find the requested Screen Shot.
Actully my problem is that, I can't configure my Cisco 3945 Routers (Shows not applicable devices) via NetConfig tool. I can use other tools like Sync archieve and etc is working fine for these 3945 routers.
Best regards;
Shoaib Ahmed

How to bridge a linksys cisco E1200 series router?

I have recently purchased a linksys cisco E1200 series router and would like to know how to bridge the connection to my xbox

purchase 881w, get rid of linksys. That should do it.
Sent from Cisco Technical Support iPad App

Configuring New Interface and NAT on Cisco 1900 Series Router.

Hello Cisco Team,
am asking for advise on how to how setup NAT rules and overload on my 2nd interface on my cisco 1900 series router,am not sure where am getting it wrong.
my router has 2 interface, interface one has IP address 10.5.5.5X and plugs into my ASA firwall and into my switch and works just fine.
i have just configured my second Interface with a new IP 172.16.0.X- i want to NAT my new IP address to our public IP address which is 41.77.X.X
my configuration so far are as follows.
GigabitEthernet0/0 172.16.0.X YES manual up up - Not working
GigabitEthernet0/1 10.5.5.X YES NVRAM up up- this works fine
GigabitEthernet0/0/0 41.77.X.X YES NVRAM up up

Hello Jon,
Thanks for your feedback, my router configuration are as follows.
interface GigabitEthernet0/0
description WL2504
ip address 172.16.0.2 255.255.254.0
duplex auto
speed auto
interface GigabitEthernet0/1
description WAN
ip address 10.55.55.2 255.255.255.252
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface GigabitEthernet0/0/0
description LINK TO CLT INTERNET
ip address 41.X.X.130 255.255.255.248
ip nat outside
ip virtual-reassembly in
duplex full
speed 100
media-type sfp
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 1 interface GigabitEthernet0/0/0 overload
ip route 0.0.0.0 0.0.0.0 41.X.X.129
ip route 41.X.X.136 255.255.255.248 10.55.55.1
ip route 192.168.0.0 255.255.255.0 10.55.55.1
access-list 1 permit 10.55.55.0 0.0.0.255
access-list 1 permit 192.168.0.0 0.0.0.255
access-list 1 permit 192.168.1.0 0.0.0.255
from the router interface  interface GigabitEthernet0/0- I will connect it to my wireless Controller WL 2504

IOs for cisco 1900 series router

Hi,
Kindly provide me the IOS version (cisco 1900 router) which can fix the below listed Bugs,
Cisco IOS TCP Listener Crafted Packets Remote DoS (CSCek37177)
Cisco Multiple Devices Crafted IP Option Remote Code Execution (CSCeh52410)
Cisco IOS System Timers Remote Overflow (CSCei61732)
Cisco IOS Secure Shell Server TACACS+ Multiple DoS (CSCed65778, CSCed65285)
Cisco IOS IKE XAUTH ISAKMP IPSec SA Establish Authentication Bypass(CSCeg00277)
Cisco IOS Telnet Service DoS (CSCef46191)
Cisco IOS H.323 Protocol Implementation Flaws Cisco IOS Malformed IPv4 Packet Remote DoS Cisco SSH2 Server/Client Malformed Packet Remote DoS (CSCdz60229, CSCdy87221, CSCdu75477)
Cisco IOS SSH Large Packet CPU Consumption DoS (CSCdw33027) Cisco SIP Crafted INVITE Message Handling DoS (CSCdz39284, CSCdz41124) Cisco IOS Data-link Switching (DLSw) Capabilities Exchange Remote DoS (CSCsf28840)
Cisco IOS AAA RADIUS Long Username Authentication Bypass (CSCee45312)
Cisco IOS TCLSH AAA Command Authorization Bypass (CSCeh73049)
Cisco IOS MMP Stack Group Bidding Protocol (SGBP) Crafted UDP Packet Remote DoS (CSCsb11124)
Cisco IOS IPv6 Packet Processing Arbitrary Code Execution (CSCef68324)
Cisco IOS Malformed BGP Packet Processing Remote DoS (CSCee67450)
Cisco IOS Multi Protocol Label Switching (MPLS) Packet Remote DoS (CSCeb56909)
Cisco IOS IPv6 Packet Processing Remote DoS (CSCed40933)
Cisco IOS SCCP Control Protocol Malformed Message DoS (CSCee08584)
Cisco IOS OSPF Packet Handling DoS (CSCec16481) Cisco IOS ARP Table Overwrite DoS (CSCdu81936)
Regards,
Bala

Hi,
The Current running IOS version is 12.2(4)T7. I tried through bug toolkit. but i couldn't able to consolidate the IOS to fix these bugs.
Regards,
A.Bala
leolaohoo wrote at Tue Jan 25 02:20:52 GMT+05:30 2011:
>Balakrishnan Appavu,
>
>A new message was posted in the Discussion thread "IOs for cisco 1900 series router":
>
>https://supportforums.cisco.com/message/3277195#3277195
>
>Author : leolaohoo
>Profile : https://supportforums.cisco.com/people/leolaohoo
>
>Message:

Group Policy question about setting Start menu items using devices and not users

I am using Windows Server 2003 and Windows Server 2008 R2 servers set up for use as Active Directory Servers.
What I am trying to do is lock down thin clients start menu options and I have been able to get this to work down to the user level. However, what I want to do is have it locked down on the machine level.
We have multiple users that use both "Thin Clients" with Windows 7 Embedded and we also have them using other PC's with using the same log in.
So, for example when you create an OU for "Thin Clients", I want thin client devices in there and when people log in to these thin clients then the start menu will be locked down. I want this to be user independent and thus I don't want Users
in the OU, but I want to lock down the start menu.
How can I do this with Group Policy Objects on a domain level?

Hi,
you could achieve this using GPO loopback processing. It was designed for the purpose of applying settings from user GPO to a certain group of computers.
http://technet.microsoft.com/en-us/library/cc978513.aspx
MCP/MCSA/MCTS/MCITP

Question about setting track level

Hi I finally got my new macbook pro and moto 8 pre and have just today tried a bit of recording just to get used to it. I am at the moment using garage band. I have a question about track levels. In Garage Band when I select a track to record there is a slider for input level or an option of clicking the automatic level control. But for some reason they are both just that color of grey you get when something can not be selected on a computer. How do I activate this? It's strange as I did actually manage to record the track, I just can't seem to really adjust the level. I thought maybe it has to do with the motu and I can only select the track level there, and that garage band level setting are (rightfully) disabled? Maybe that's what I should be doing, but just a bit confused. Anyway, thanks in advance for whoever takes the time to help out a newbie.

Ah, ok. Good to know. Thanks for the info.

Question about sets in report painter.

Hi, everybody. Please, could someone help me in this matter?.
I wanna delete a set with the GS04 transaction in Report Painter but I cannot.
When I put the set's id (XXX) in the set's name and push Delete-Set-F8 button, I get the following error:
The XXX set cannot be deleted.I consult the error with the help and SAP tells me that I need to use the set-usage option to view where the set is used in the system.
I select this set-usage option under the utilities menu and SAP tells me that the set is being used in a report.
The thing is that the report doesnt exist. I deleted the report before. Why the error is then.
However, I created, generated and compiled the report again in report painter with other different set so that I confirmed that the report was not using the XXX set and the error continues with report or without it.
That I tried to say was that the XXX set is not being used anywhere and the question then is why report painter is telling me that the set is being used in a report. Thing that is not true.
Thanks and I hope someone can help me out!!

Hi, everybody. Please, could someone help me in this matter?.
I wanna delete a set with the GS04 transaction in Report Painter but I cannot.
When I put the set's id (XXX) in the set's name and push Delete-Set-F8 button, I get the following error:
The XXX set cannot be deleted.I consult the error with the help and SAP tells me that I need to use the set-usage option to view where the set is used in the system.
I select this set-usage option under the utilities menu and SAP tells me that the set is being used in a report.
The thing is that the report doesnt exist. I deleted the report before. Why the error is then.
However, I created, generated and compiled the report again in report painter with other different set so that I confirmed that the report was not using the XXX set and the error continues with report or without it.
That I tried to say was that the XXX set is not being used anywhere and the question then is why report painter is telling me that the set is being used in a report. Thing that is not true.
Thanks and I hope someone can help me out!!

Question about setting up rdp using a cisco 800 series router

Similar Messages

Maybe you are looking for