Question on example "configuring qllc to eth with local switching"
Hello,
I am reffering to the example on page
http://www.cisco.com/en/US/partner/tech/tk331/tk336/technologies_configuration_example09186a0080093fba.shtml
Let's consider that the Mainframe is on the ethernet side (OSA card) and the station on the serial side. Then I guess the example will work fine.
To make things more complecated, now suppose that there is another station on another serial let say s0/1, with its own x.121 address, whereas the station is on s0/0. Now, if the station also wants to speak x.25 with the server on s0/1, how this could be accomplished? Does the configuration of the s0/0 with the x25 map and qllc dlsw commands, forbids the station from talking to other serial interfaces? Or if I just add a x.25 route to the s0/1, then whenever station asks for the x.121 address of the server it will be guided there?
Regards, Apostolos.
I am sorry but I think the question as it was set was a bit confusing. So, please let me rephrase it using the same example as basis. Let's consider we have two AS400 (a & b) connected with x25 to two serials on a router. This router is connected with a x.25 serial interface with another router, at serial s0/0, which has two connections:
i) Ethernet to mainframe (OSA)
ii) Serial (s0/1) x25 to another server (Stratus)
AS400A is to speak with OSA card whereas AS400B is to speak with the stratus server.
If I configure the serial interface to map x25 address of AS400A to a vmac and guide this to OSA, then will the other AS400B be able to connect to the Stratus?
Similar Messages
-
Help needed to configure H-REAP with local switching
Hi All,
We are using following devices for campus Wi-fi.
1. WLC - 4402
2. AP (1131ag, 1042n) which support H-REAP.
I want to configure HREAP central auth and local switching. I have enabled from local to HREAP after that I go to HREAP tab and native vlan 1 (by default)(I have changed native vlan 1 to 51.) vlan support is enabled. then click on vlan mapping and my wlan (guestwlan) is there with vlan id 24.
I have assigned static IP to AP (192.168.51.40/24 gw 192.168.51.254).
DHCP is running on controller.
switch port configure is below:
interface FastEthernet0/18
description WiFi access point
switchport trunk native vlan 51
switchport mode trunk
no ip address
end
Issue : authentication done through RADIUS (Cisco ACS 4.2) but no getting IP address from DHCP.
Please help.
Thanks in Adv.
Thanks,
ASHi AS,
Do not use the DHCP on the WLC.
Use a DHCP on the neighbor swtich if possible for the native VLAN.
Regards,
Amjad
Rating useful replies is more useful than saying "Thank you" -
Configure Word 2010 startup with /n switch.
Hello,
Opening MS Word with /n switch, Example "C:\Program Files\Microsoft Office\Office\Winword.exe" /n, Word 2010 will start a new instance of Word with no document open. Can this be done via GPO as we are looking into configuring this for hundreds
of users. Thanks.Hi,
I don't know a direct way to realize this via GPO, but a workaround may be helpful.
Since the path for all users should be the same(C:\Program Files\Microsoft Office\Office\Winword.exe), we can make one shortcut, then modify its Properties -> Add
/n to the target behind the full path C:\Program Files\Microsoft Office\Office\Winword.exe. It will be like "C:\Program Files\Microsoft Office\Office\Winword.exe" /n
in the shortcut properties, save it to a shared folder, then create a startup script which pulls this shortcut from the shared folder to the user's local desktop.
Since I'm not a script expert, you may need to contact other resource for further assistance.
Regards,
Melon Chen
TechNet Community Support
It's recommended to download and install
Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
programs. Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected] -
Multiple VLANs per SSID with local switch
Is it possible to use an 'AP Group' or 'Interface group' to assign multiple VLANs to a WLAN when remote, h-reap APs are in local switch mode?
If not, is there a way to overcome 500 maximum host per VLAN when APs are local switching?
Thanks!dont think its possible...
I donno if the following config will even work but u can have the hreap APs connected at the remote site to map to different vlans...
Example:
AP1 -- ssid 1 --- vlan 10
AP2 -- said 1 --- vlan 11 and so forth..
Sounds crazy but i ll have to ponder on this a bit more.. Need a pen and paper to draw a quick topology :)...
Sent from Cisco Technical Support iPhone App -
Configure Jabber for Mac with local CUCM and WebEx Connect
Hi, I was wondering if anyone has been able to configure the Jabber for Mac 8.6.2 client to use the WebEx Connect presence server with a local CUCM and Unity Connection servers. The preferences accounts tab does not show or allow the addition of the voice services. I have added from a working local CUCM preferences plist file what I believe are the correct entries however I still cannot see the accounts on the preferences tab. We currently do not have a local cisco presence server hence the requirement to trial the WebEx Connect server as I can't get past the first configuration step without it.
regards
paulHi - I have done this via the admin portal but still cannot get the Jabber client for Mac to register for voice. The Windows version works fine for the same user and CUCM device. Are there any other settings that need to be enabled specific to the Mac client?
Thanks. -
ISE works with Local-switch Mode
Hi guys,
My AP is configured to work as Flexconnect mode with my WLC, that means that my wireless data will be switched locally without getting through my WLC, is that ok for my ISE to controll my wireless access?
Regards,Yes; FlexConnect supports central authentication with both locally and centrally switched traffic models.
Lots of info about FlexConnect here;
http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/flexconnect/config_flexconnect_chapter_01.html -
Configuration of Cisco WLC 2504 with Local LAN static IP and DHCP
I want to configure Cisco WLC 2504 with Local LAN static IP and WLC 2504 with DHCP so that APs can be connect with controller.
Currently i am using WLC 2504 with DHCP so can anyone suggest how to do that..Hi Sandeep
The info is correct, if we're using code below 7.3.101.0.
This issue is fixed via the below bug id.
CSCto01390 Unable to ping AP's directly connected to a 2500 controller
check the fix that is updated on 7.4, 7.5 RNE.
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn75.html
Note
Directly connected APs are supported only in Local mode.
http://www.cisco.com/en/US/prod/collateral/wireless/ps6302/ps8322/ps11630/data_sheet_c78-645111.html
For quick and easy deployment Access Points can be connected directly to 2504 Wireless LAN Controller via two PoE (Power over Ethernet) ports
Thanks
Saravanan -
Flex connect with a per user ACL with APs locally switched
Hi all,
Does flex connect allow a per user ACL to be downloaded to the session with local switched, central authentication? We are using ISE for the central policy engine and have setup dACL for wired but am about to embark on WLAN. The controller is a 5508 and the. APs are 3700's.
Second question- if the flex connect APs don't do any form of per user ACL, the other option is to have the units in regular mode where they are both centrally switched and centrally authenticated which I understand to support a per user ACL. Our WAN links are between 10mbps - 30mbps and the most latency would be around 40ms. Will this cause issues at all with the size WAN links and latency?
Thanks
Sent from Cisco Technical Support iPad AppWell you are running v7.6 so FlexConnect per user radius ACL's are supported per this doc since v7.5.
http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/112042-technote-product-00.html#anc9
As far as WAN latency, 200ms is good, but it depends in your WAN utilization now and how many AP's you plan on installing and the increase in wireless traffic across your WAN. There is a minimum requirement, but it's up to you in the end to make sure you have enough bandwidth or else you will need to QoS the capwap traffic to ensure the APs don't bounce from connected to stand alone.
Sent from Cisco Technical Support iPhone App -
How to Configure a mail server with OIM
Experts ,
Any idea/links/Docs on how to configure a mail server with OIM and to send mail notification to someone .
Pardon me, if my questions seems to be incomplete .
Thanks
Suren.Create an IT Resource of Type Mail Server. Give Name as "Email Server.Now populate the values for all the parameter for example Server,username,password and authentication type.
.Go to System Configuration and in Email Server property value give the name of IT resource you created in step1 so the name will be "Email Server".
http://forums.oracle.com/forums/messageview.jspa?messageID=3867506&stqc=true -
I have a question about our SSLM configure, please see the following example:
service aa-SSL
virtual ipaddr 172.25.17.15 protocol tcp port 443 secondary
server ipaddr 172.24.92.6 protocol tcp port 80
certificate rsa general-purpose trustpoint www.app.aa.com
no nat server
inservice
crypto pki trustpoint www.app.aa.com
revocation-check none
rsakeypair www.app.aa.com
crypto ca import www.app.aa.com pkcs12 tftp:xxx
======================================
Once we finish the configuration, we could find the corresponding cer in SSLM, like:
crypto pki certificate chain www.app.aa.com
My first question is how to remove this cert if we want to decommission aa-ssl environment? Is it only with âno crypto pki certificate chain www.app.aa.comâ
If we have another environment like www.pre.app.aa.com shared the same VIP with www.app.aa.com. My second question is could I create only one ssl entry with wildcard like the following configuration:
service aa-SSL
virtual ipaddr 172.25.17.15 protocol tcp port 443 secondary
server ipaddr 172.24.92.6 protocol tcp port 80
certificate rsa general-purpose trustpoint *.app.aa.com
no nat server
inservice
Please advice! I would appreciate it!You can remove the certificate but you need to be in certificate chain configuration mode to delete certificates. An example configuration is provided here
http://www.cisco.com/en/US/docs/ios/security/command/reference/sec_c5.html#wp1043434 -
Configured Item - append sequence with item segment
Hi,
Is there any possible to have sequence number starting from 1,2,3... for each CTO BOM?
Say for example, there is a CTO BOM and out of which 10 possible configurations can be done and each configured item shoud have itemsegment-1, itemsegment-2...etc.
Thanks in Advance!
KaveriHi Sabari,
Configurable BOM - item segment is C0200D0000XX and the setup made in BOM Parameters is 'Append sequence with Item Segment'
The number generated for one of configuration is C0200D0000XX-6202980.
My question is can't the sequence be started with 1 for each configurable BOM? If so how to do it?
Example:
Configurable BOMS - C0300D0000XX which supports five possible valid configurations and the item numbers expected are C0300D0000XX-1, C0300D0000XX-2, C0300D0000XX-3, C0300D0000XX-4, C0300D0000XX-5
Another CTO BOM C00600D0000XX which supports 3 valid configurations and numbers would be C00600D0000XX-1, C00600D0000XX-2,C00600D0000XX-3
Thanks,
Kaveri -
A few questions regarding the configuration of Adobe Document Services
<u><i>For Your Information: the main questions are repeated at the end of this post.</i></u>
The Adobe Document Services seems to work fine. The test I did on http://<server>:<port>/AdobeDocumentServices/Config gives the error
' "Required stream: "PDFDocument" not found. ' so that's fine.
But when I do this: http://server:50000/webdynpro/dispatcher/local/TutWD_OnlineInteractiveForm/OnlineInteractiveFormApp
The result: the PDF is shown and I can enter text in the textboxes and also use the radioboxes.
But I can't use the dropdownboxes, neither can I use the "submit" and "check" buttons..
Is this normal? Or is it because of the ReaderRights credential?
Or is it necessary to install the ACF?
Here is some info I got from a blog:
"<b>Client Side Requirements</b>
Follow the steps mentioned below. Please make sure the following prerequisites are met before working with Adobe Interactive Forms.
NWDS 7.0 / 6.0
Adobe Live cycle designer 7.1 / 7.0
Adobe Reader 7.0.8 [ Minimum : 7.0.1]
<b>End User Requirements</b>
Adobe Reader 7.0.8 [ Minimum : 7.0.1]
Active Component Framework (ACF) - SPS 9, SPS 10"
Two more questions;
1)This info is in the config guide:
"If you have installed the ADS and the WD runtime environment on different J2EE engines and if the communication between these engines uses the SLD, you need to publish the ADS to the SLD."
Does this mean that I don't need to do this when I haven't used SLD? Or is it necessary to install SLD?
Some more info:
Prerequisites:
A System Landscape Dir must already have been configured.
If you have not yet done so, perform the necessary activities according to the documentation SAP System Landscape Directory, Administrative Activities section, chapters:
Start and stop the SLD Service
Configure the SLD Server
Configure data persistence
Make settings for the SLD bridge
You can find this documentation by calling the following URL in your web
browser: http://<host>:<port>/sld
When I check this URL, I don't see anything concerning an (already configured) SLD.
2) Do I need the license below too to develop in AIF?
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes/sdn_oss_bc_srv/~form/handler%7b5f4150503d3030323030363832353030303030303031393732265f4556454e543d444953504c4159265f4e4e554d3d373530373834%7d
Main questions----
I need to create a form with a few fields (of which some fields are mandatory); then I have to use a few BAPI's to check these fields and to save the content in a CRM system.
I've installed Netweaver Sneak Preview, and configured Adobe Document Services (made ADSUser & ADSCaller, set IIOP etc to Autostart, Installed the credentials). The tests seem to work fine, but I haven't developed anything yet.
My questions:
1)Is it necessary to install the ACF?
2)Is it necessary to install Adobe LifeCycle Designer?
3)Also SLD?
4)Also the license described above?
Grz
Allan
Message was edited by:
Allan DuinslaegerNo one?
Some questions are answered by someone else.
-The SLD is okay, it doesn't need to be configured
-The Adobe Lifecycle Designer is automatically installed when installing the Netweaver Studio Sneak Preview SP16
Just two more questions:
1)when I open http://server:port/webdynpro/dispatcher/local/TutWD_OnlineInteractiveForm/OnlineInteractiveFormApp
The PDF is shown but I can't use the buttons or the dropdown boxes.
I tried to install ACF but I have NW04s SP16, and the ACF is only SP11.
So when I install that, it only shows a blue screen with "I am the placeholder control"
When I install ACF SP19 for NW04, the PDF shows again, but I still can't use the buttons or dropdowns. Is this normal?
2) Do I need the license described below?
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes/sdn_oss_bc_srv/~form/handler%7b5f4150503d3030323030363832353030303030303031393732265f4556454e543d444953504c4159265f4e4e554d3d373530373834%7d
Main questions----
I need to create a form with a few fields (of which some fields are mandatory); then I have to use a few BAPI's to check these fields and to save the content in a CRM system.
I've installed Netweaver Sneak Preview, and configured Adobe Document Services (made ADSUser & ADSCaller, set IIOP etc to Autostart, Installed the credentials). The tests seem to work fine, but I haven't developed anything yet.
My questions:
1) What about the ACF?
2) Also the license described above?
Grz
Allan -
Configuring Apache HTTP Server with Oracle Weblogic Server plugin
Hello friends,
I have a scenario of OIM 9.1.0.2 on Oracle Application Server 11g and Weblogic Server Apache HTTP Server.
Oracle WebLogic Server is configured in cluster (node1 and node2), also use the Oracle Weblogic Server plugin for integration with Apache.
One of the tests is to lose one of the nodes for the apache plugin redirects the node that has less overhead.
When the mode is node1 and node2 stop start mode and try to access the management console of Oracle Identity Manager, the plugin sometimes redirects to the other active node, and on another occasion shows the oracle management console identity manager without the colors of the basic look and feel.
Deputy of the Apache HTTP Server log, do you expect your comments to solve this case?
*************************************************log****************************************************
Server Details are:
OrigHostInfo [192.168.1.200]
isOrigHostInfoDNS [0]
Host [192.168.1.200]
Port [7002]
SecurePort [7004]
Mon Jan 30 22:10:43 2012 <2600713279794431> Initializing lastIndex=0 for a list of length=1
Mon Jan 30 22:10:43 2012 <2600713279794431> initJVMID: Trying to locate Primary or Secondary using SrvrInfo with JVMID [-872106207]
Mon Jan 30 22:10:43 2012 <2600713279794431> initJVMID: Found Primary 192.168.1.200:7002:7004
Mon Jan 30 22:10:43 2012 <2600713279794431> INFO: Closing SSL context
Mon Jan 30 22:10:43 2012 <2600713279794431> .....internal request /bea_wls_internal/WLDummyInitJVMIDs.....processed
Mon Jan 30 22:10:43 2012 <2600713279794431> getPreferredFromCookie: Found 1 servers
Mon Jan 30 22:10:43 2012 <2600713279794431> attempt #0 out of a max of 5
Mon Jan 30 22:10:43 2012 <2600713279794431> trying connect to PRIMARY '192.168.1.200'/7002/7004
Mon Jan 30 22:10:43 2012 <2600713279794431> getPooledConn: No more connections in the pool for Host[192.168.1.200] Port[7002] SecurePort[7004]
Mon Jan 30 22:10:43 2012 <2600713279794431> New SSL URL: match = 0 oid = 22
Mon Jan 30 22:10:43 2012 <2600713279794431> Connect returns -1, and error no set to 150, msg 'Operation now in progress'
Mon Jan 30 22:10:43 2012 <2600713279794431> EINPROGRESS in connect() - selecting
Mon Jan 30 22:10:43 2012 <2600713279794431> Setting peerID for new SSL connection
Mon Jan 30 22:10:43 2012 <2600713279794431> 0ae2 0436 0000 1b5c ...6...\
Mon Jan 30 22:10:43 2012 <2600713279794431> Local Port of the socket is 39186
Mon Jan 30 22:10:43 2012 <2600713279794431> Remote Host 192.168.1.200 Remote Port 7004
Mon Jan 30 22:10:43 2012 <2600713279794431> created a new connection to preferred server '192.168.1.200/7004' for '/xlWebApp/images/spacer.gif', Local port:39186
Mon Jan 30 22:10:43 2012 <2600713279794431> INFO: CA certificate missing basicConstraints, validation failed
Mon Jan 30 22:10:43 2012 <2600713279794431> ERROR: SSLWrite failed
Mon Jan 30 22:10:43 2012 <2600713279794431> SEND failed (ret=-1) at 793 of file ../nsapi/URL.cpp
Mon Jan 30 22:10:43 2012 <2600713279794431> *******Exception type [WRITE_ERROR_TO_SERVER] raised at line 794 of ../nsapi/URL.cpp
Mon Jan 30 22:10:43 2012 <2600713279794431> Marking 192.168.1.200:7004 as bad
Mon Jan 30 22:10:43 2012 <2600713279794431> got exception in sendRequest phase: WRITE_ERROR_TO_SERVER [os error=0, line 794 of ../nsapi/URL.cpp]: at line 3160
Mon Jan 30 22:10:43 2012 <2600713279794431> INFO: Closing SSL context
Mon Jan 30 22:10:43 2012 <2598413279794431>
================New Request: [GET /images/cab.gif HTTP/1.1] =================
Mon Jan 30 22:10:43 2012 <2598413279794431> INFO: SSL is configured
Mon Jan 30 22:10:43 2012 <2598413279794431> SSL Main Context not set. Calling InitSSL
Mon Jan 30 22:10:43 2012 <2598413279794431> INFO: SSL configured successfully
Mon Jan 30 22:10:43 2012 <2598413279794431> Using Uri /images/cab.gif
Mon Jan 30 22:10:43 2012 <2598413279794431> After trimming path: '/images/cab.gif'
Mon Jan 30 22:10:43 2012 <2598413279794431> adding prepend path: /xlWebApp/
Mon Jan 30 22:10:43 2012 <2598413279794431> The final request string is '/xlWebApp/images/cab.gif'
Mon Jan 30 22:10:43 2012 <2598413279794431> Host extracted from serverlist is [192.168.1.100]
Mon Jan 30 22:10:43 2012 <2598413279794431> Host extracted from serverlist is [192.168.1.200]
Mon Jan 30 22:10:43 2012 <2598413279794431> Initializing lastIndex=0 for a list of length=2
Mon Jan 30 22:10:43 2012 <2598413279794431> getListNode: created a new server node: id='192.168.1.100:7004,192.168.1.200:7004' server_name='OIMSERVER', port='443'
Mon Jan 30 22:10:43 2012 <2598413279794431> getPreferred: availcookie=[JSESSIONID=6RGCPnbTFRG7LBrTRpFnv1QLnQHkxkqr4pjGhhGJyrJWJ1rv86NK!-872106207!NONE]
Mon Jan 30 22:10:43 2012 <2598413279794431> Found cookie from cookie header: JSESSIONID=6RGCPnbTFRG7LBrTRpFnv1QLnQHkxkqr4pjGhhGJyrJWJ1rv86NK!-872106207!NONE
Mon Jan 30 22:10:43 2012 <2598413279794431> Parsing cookie JSESSIONID=6RGCPnbTFRG7LBrTRpFnv1QLnQHkxkqr4pjGhhGJyrJWJ1rv86NK!-872106207!NONE
Mon Jan 30 22:10:43 2012 <2598413279794431> getpreferredServersFromCookie: [-872106207!NONE]
Mon Jan 30 22:10:43 2012 <2598413279794431> primaryJVMID: [-872106207]
secondaryJVMID: [NONE]
Mon Jan 30 22:10:43 2012 <2598413279794431> No of JVMIDs found in cookie: 1
Mon Jan 30 22:10:43 2012 <2598413279794431> getPreferredFromCookie: Start Position is 0, listLen is 2
Mon Jan 30 22:10:43 2012 <2598413279794431> getPreferredFromCookie: Either JVMIDs not set or they are stale. Will try to get JVMIDs from WLS
Mon Jan 30 22:10:43 2012 <2598413279794431> initJVMID: Iterating SrvrList from position 0
Mon Jan 30 22:10:43 2012 <2598413279794431> ======internal request /bea_wls_internal/WLDummyInitJVMIDs======
initJVMID: Trying Host[192.168.1.100] Port[7004] SecurePort[7004] useSSL [1] ioTimeout [30] socketTimeout [2]
Mon Jan 30 22:10:43 2012 <2598413279794431> New SSL URL: match = 0 oid = 0
Mon Jan 30 22:10:43 2012 <2598413279794431> Connect returns -1, and error no set to 146, msg 'Connection refused'
Mon Jan 30 22:10:43 2012 <2598413279794431> Error connecting to host 192.168.1.100:7004
Mon Jan 30 22:10:43 2012 <2598413279794431> *******Exception type [CONNECTION_REFUSED] (Error connecting to host 192.168.1.100:7004 errno = 146) raised at line 1723 of ../nsapi/URL.cpp
Mon Jan 30 22:10:43 2012 <2598413279794431> initJVMID: Failed to retrieved JVMID for 192.168.1.100:7004:7004
Mon Jan 30 22:10:43 2012 <2598413279794431> initJVMID: Marked server as BAD
Mon Jan 30 22:10:43 2012 <2598413279794431> INFO: Closing SSL context
Mon Jan 30 22:10:43 2012 <2598413279794431> .....internal request /bea_wls_internal/WLDummyInitJVMIDs.....processed
Mon Jan 30 22:10:43 2012 <2598413279794431> ======internal request /bea_wls_internal/WLDummyInitJVMIDs======
initJVMID: Trying Host[192.168.1.200] Port[7004] SecurePort[7004] useSSL [1] ioTimeout [30] socketTimeout [2]
Mon Jan 30 22:10:43 2012 <2598413279794431> New SSL URL: match = 0 oid = 0
Mon Jan 30 22:10:43 2012 <2598413279794431> Connect returns -1, and error no set to 150, msg 'Operation now in progress'
Mon Jan 30 22:10:43 2012 <2598413279794431> EINPROGRESS in connect() - selecting
Mon Jan 30 22:10:43 2012 <2598413279794431> Setting peerID for new SSL connection
Mon Jan 30 22:10:43 2012 <2598413279794431> 0ae2 0436 0000 1b5c ...6...\
Mon Jan 30 22:10:43 2012 <2598413279794431> Local Port of the socket is 39188
Mon Jan 30 22:10:43 2012 <2598413279794431> Remote Host 192.168.1.200 Remote Port 7004
Mon Jan 30 22:10:43 2012 <2598413279794431> INFO: Certificate validation succeeded
Mon Jan 30 22:10:43 2012 <2598413279794431> INFO: Negotiated to cipher: 3
Mon Jan 30 22:10:43 2012 <2598413279794431> SSLWrite sent 171
Mon Jan 30 22:10:43 2012 <2598413279794431> SSLWrite completed, sent 171
Mon Jan 30 22:10:43 2012 <2598413279794431> Reader::fill() SSLRead returned: 0 290
Mon Jan 30 22:10:43 2012 <2598413279794431> URL::parseHeaders: CompleteStatusLine set to [HTTP/1.1 404 Not Found]
Mon Jan 30 22:10:43 2012 <2598413279794431> URL::parseHeaders: StatusLine set to [404 Not Found]
Mon Jan 30 22:10:43 2012 <2598413279794431> parsed all headers OK
Mon Jan 30 22:10:43 2012 <2598413279794431> Parsing cluster list: -872106207!182584374!7002!7004
Mon Jan 30 22:10:43 2012 <2598413279794431> parseJVMID: Parsing JVMID '-872106207!182584374!7002!7004'
Mon Jan 30 22:10:43 2012 <2598413279794431> parseJVMID: Actually parsing '-872106207!182584374!7002!7004'
Mon Jan 30 22:10:43 2012 <2598413279794431> ServerInfo struct for JVMID '-872106207' populated
Server Details are:
OrigHostInfo [192.168.1.200]
isOrigHostInfoDNS [0]
Host [192.168.1.200]
Port [7002]
SecurePort [7004]
Mon Jan 30 22:10:43 2012 <2598413279794431> Initializing lastIndex=0 for a list of length=1
Mon Jan 30 22:10:43 2012 <2598413279794431> initJVMID: Trying to locate Primary or Secondary using SrvrInfo with JVMID [-872106207]
Mon Jan 30 22:10:43 2012 <2598413279794431> initJVMID: Found Primary 192.168.1.200:7002:7004
Mon Jan 30 22:10:43 2012 <2598413279794431> INFO: Closing SSL context
Mon Jan 30 22:10:43 2012 <2598413279794431> .....internal request /bea_wls_internal/WLDummyInitJVMIDs.....processed
Mon Jan 30 22:10:43 2012 <2598413279794431> getPreferredFromCookie: Found 1 servers
Mon Jan 30 22:10:43 2012 <2598413279794431> attempt #0 out of a max of 5
Mon Jan 30 22:10:43 2012 <2598413279794431> trying connect to PRIMARY '192.168.1.200'/7002/7004
Mon Jan 30 22:10:43 2012 <2598413279794431> getPooledConn: No more connections in the pool for Host[192.168.1.200] Port[7002] SecurePort[7004]
Mon Jan 30 22:10:43 2012 <2598413279794431> New SSL URL: match = 0 oid = 22
Mon Jan 30 22:10:43 2012 <2598413279794431> Connect returns -1, and error no set to 150, msg 'Operation now in progress'
Mon Jan 30 22:10:43 2012 <2598413279794431> EINPROGRESS in connect() - selecting
Mon Jan 30 22:10:43 2012 <2598413279794431> Setting peerID for new SSL connection
Mon Jan 30 22:10:43 2012 <2598413279794431> 0ae2 0436 0000 1b5c ...6...\
Mon Jan 30 22:10:43 2012 <2598413279794431> Local Port of the socket is 39189
Mon Jan 30 22:10:43 2012 <2598413279794431> Remote Host 192.168.1.200 Remote Port 7004
Mon Jan 30 22:10:43 2012 <2598413279794431> created a new connection to preferred server '192.168.1.200/7004' for '/xlWebApp/images/cab.gif', Local port:39189
Mon Jan 30 22:10:43 2012 <2598413279794431> INFO: CA certificate missing basicConstraints, validation failed
Mon Jan 30 22:10:43 2012 <2598413279794431> ERROR: SSLWrite failed
Mon Jan 30 22:10:43 2012 <2598413279794431> SEND failed (ret=-1) at 793 of file ../nsapi/URL.cpp
Mon Jan 30 22:10:43 2012 <2598413279794431> *******Exception type [WRITE_ERROR_TO_SERVER] raised at line 794 of ../nsapi/URL.cpp
Mon Jan 30 22:10:43 2012 <2598413279794431> Marking 192.168.1.200:7004 as bad
Mon Jan 30 22:10:43 2012 <2598413279794431> got exception in sendRequest phase: WRITE_ERROR_TO_SERVER [os error=0, line 794 of ../nsapi/URL.cpp]: at line 3160
Mon Jan 30 22:10:43 2012 <2598413279794431> INFO: Closing SSL context
Thanks"One of the tests is to lose one of the nodes for the apache plugin redirects the node that has less overhead."
Note that the plug-in does a round robin load balancing, for example, in the case of three server (1,2,3) it does 1-2-3-1-2-3-1...
with server 3 going down it does 1-2-1-2-1...
An example configuration (with SSL off) looks as follows:
LoadModule weblogic_module "/home/oracle/weblogic12.1.1/apache/modules/mod_wl.so"
<IfModule weblogic_module>
ConnectTimeoutSecs 10
ConnectRetrySecs 2
DebugConfigInfo ON
WLSocketTimeoutSecs 2
WLIOTimeoutSecs 300
Idempotent ON
FileCaching ON
KeepAliveSecs 20
KeepAliveEnabled ON
DynamicServerList ON
WLProxySSL OFF
</IfModule>
<Location /LoadTest6>
SetHandler weblogic-handler
WebLogicCluster 172.31.0.175:7002,172.31.0.113:7003
</Location>Also see the complete example here: http://middlewaremagic.com/weblogic/?p=7795
"the plugin sometimes redirects to the other active node"
This is somewhat strange, do you have session binding turned off?
"and on another occasion shows the oracle management console identity manager without the colors of the basic look and feel."
This could happen due to mime types (not really sure just a hunch). Here is a general story on this concept: https://developer.mozilla.org/en/Properly_Configuring_Server_MIME_Types
and the apache module: http://httpd.apache.org/docs/2.2/mod/mod_mime.html -
How to configure the .ini file with applet
hai
i am using native methods in that methods they use some ip addresses. when i am using that native methods in applet run the applet using appletviewer tool it works fine but when i am open that applet using html page browser not configure that .ini file data .how to configure that .ini file with browserHi Jay SenSharma,
Thanks for your immediate response.
I saw your URL links, But in your link give the recursive deployment using wlst. But my question is how to configure the oracle weblogic library files into Admin server & Managed Servers by using the wls.jar file through wlst script to create the new domain.
But if create the new domain by using GUI mode then we manually give the admin server port number & managed servers port number and name.
By default the library files are configured with the Admin server in GUI mode. But the Managed server the Library files are not configured with the Managed servers. Then we manually select all the library files to the corresponding managed servers. Then only the applications are deployed into the corresponding managed server.
Regards,
S.vinoth Babu -
Example Config ACE routed mode with NAT
Hi all,
i have a two-arm loadbalancer (routed mode).
client ->vlan100->[VIP]Loadbalancer[NAT] ->vlan200-> serverfarm
But i have my problems to configure the NAT. Can anybody show me a example configuration of a two-arm loadbalancer with NAT?
Especially the access-list, class-map, policy-map and on which interface the NAT-Policy must be added.
BR
DominikHi Dominik,
Something like this:
access-list ANYONE line 10 extended permit ip any any
rserver host SERVER_01
ip address 10.198.16.2
inservice
rserver host SERVER_02
ip address 10.198.16.3
inservice
rserver host SERVER_03
ip address 10.198.16.4
inservice
serverfarm host REAL_SERVERS
rserver SERVER_01
inservice
rserver SERVER_02
inservice
rserver SERVER_03
inservice
class-map match-all VIP-30
2 match virtual-address 192.168.1.30 tcp eq www
class-map type management match-any REMOTE_ACCESS
description remote-access-traffic-match
2 match protocol telnet any
3 match protocol ssh any
4 match protocol icmp any
policy-map type management first-match REMOTE_MGT
class REMOTE_ACCESS
permit
policy-map type loadbalance first-match SLB_LOGIC
class class-default
serverfarm REAL_SERVERS
policy-map multi-match CLIENT_VIPS
class VIP-30
loadbalance vip inservice
loadbalance policy SLB_LOGIC
loadbalance vip icmp-reply active
nat dynamic 1 vlan 452
interface vlan 451
ip address 192.168.1.2 255.255.255.0
access-group input ANYONE
service-policy input CLIENT_VIPS
no shutdown
interface vlan 452
description Servers vlan
ip address 10.198.16.1 255.255.255.0
access-group input ANYONE
nat-pool 1 10.198.16.5 10.198.16.5 netmask 255.255.255.0 pat
no shutdown
ip route 0.0.0.0 0.0.0.0 192.168.1.1
Cesar R
ANS Team
Maybe you are looking for
-
Creation of Material from SAP VIEW using CDESK.
Hi Experts, I have one question related to creation of Material from SAP View. CAD file created say SM1000.prt Create DIR in CAD View say SM1000 Scenario 1 : Create Material in Background from CAD VIEW or SAP VIEW from cad desktop, It creates mate
-
Update VEKP-EXIDV2 during automatic HU creation from outbound delivery
Hi All, I need your suggestion / input on following scenario. When I create an outbound delivery and save it, an automatic Transfer Order is created and at the same time an HU is created for delivery. Now, I want to populate the field VEKP-EXIDV2 ( H
-
Interactive pdf without any page transition, only hyperlinks
Hi, I wanted to export an interactive pdf but I can't lock the page transition. Is that possible to have a document which you only can navigate with hyperlinks? Kind regards
-
Hi All, I am new to Unix. I have a requirement to find a Particular word "HTTP" or "URL" or "WEBSITE" in unix box. There are n types of files which can have these words. i am able to do this using find . -exec egrep -il "HTTP" '{}' \; or find . -exec
-
Immediately after updating Acrobat Pro XI to the latest version, the software no longer displays images in pdf docs. All the boxes where images are supposed to be are solid grey. Old documents that worked are no longer displayed correctly and new d