Question on UCS C series

Hello,
I have a question regarding the C series UCS.Is it possible as of now to connect it to the 6120 fabric manager and manage it from there like the blade series. Or are they only manageable through their CIMC port.
Deep.

With the current 1.3.x code this is not possible. This feature will be available in 1.4 which is just undergoing QA and should be available in the next month.
Regards,
Robert

Similar Messages

Ask the Expert: Cisco UCS B-Series Latest Version New Features

Welcome to this Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about the Cisco UCS Manager 2.2(1) release, which delivers several important features and major enhancements in the fabric, compute, and operational areas. Some of these features include fabric scaling, VLANs, VIFs, IGMP groups, network endpoints, unidirectional link detection (UDLD) support, support for virtual machine queue (VMQ), direct connect C-Series to FI without FEX, direct KVM access, and several other features.
Teclus Dsouza is a customer support engineer from the Server Virtualization team at the Cisco Technical Assistance Center in Bangalore, India. He has over 15 years of total IT experience. He has worked across different technologies and a wide range of data center products. He is an expert in Cisco Nexus 1000V and Cisco UCS products. He has more than 6 years of experience on VMware virtualization products.
Chetan Parik is a customer support engineer from the Server Virtualization team at the Cisco Technical Assistance Center in Bangalore, India. He has seven years of total experience. He has worked on a wide range of Cisco data center products such as Cisco UCS and Cisco Nexus 1000V. He also has five years of experience on VMware virtualization products.
Remember to use the rating system to let Teclus and Chetan know if you have received an adequate response.
Because of the volume expected during this event, our experts might not be able to answer every question. Remember that you can continue the conversation in the Data Center community, under subcommunity Unified Computing, shortly after the event. This event lasts through May 9, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hi Jackson,
Yes its is possible. Connect the storage array to the fabric interconnects using two 10GB links per storage processor. Connect each SP to both fabric interconnects and configure the ports on the fabric interconnect as “Appliance” ports from UCSM
For more information on how to connect Netapp storage using other protocols like iSCSI or FCOE please check the url below.
http://www.cisco.com/c/en/us/products/collateral/servers-unified-computing/ucs-6100-series-fabric-interconnects/whitepaper_c11-702584.html
Regards
Teclus Dsouza

IPv6 en de Cisco UCS B - Series

Los Cisco UCS B - Series soporta ipv6?

Hello Mario,
If your question is towards UCS management interfaces (FI and VIP interfaces) supporting IPv6 addresses - the answer is NO, UCS currently does not supports IPv6.
This is on the roadmap but nothing commited as of now.
./Abhinav

Can RedHat 5.4 fence with IPMI port on UCS B-series blade ?

Hi to all,
Is it possible for a RedHat 5.4 installed on a UCS blade to fence with a IPMI (BMC) port of another blade ?
We created and applied a IPMI profile to the target (controlled) blade. We also created and activated a Serial over Lan policy on that blade.
Linux guys say they still can't reach ports 623 (maybe Serial over Lan) and 664 (I don't know this port). We have already cheched firewalls, no drops or blocking rules.
Has anyone succeeded configuring fencing on UCS blades ? And if so, could you explain how ?
Many thanks, best regards
Daniele

At least we succeeded without using too much effort. IPMI inside UCS B series blade is itself able to be managed by RedHat 5.4, it's only a matter to configure it properly on RedHat.
No need to use Serial Over Lan policy, we have disabled it.
So this problem is solved, I can answer "yes" to my topic question.
Thank you anyway, goodbye

UCS B series IOM firmware upgarde.

Dear Experts;
We have one BUG in our UCS B series server as below link.
https://tools.cisco.com/bugsearch/bug/CSCue49366/?reffering_site=dumpcr
The work around is to do the IOM firmware upgarde.
As teher are several Firmware are associated with the UCS system how to knwo the dependency and how to know which firmware is compatible with the uCS server.
Please assist me to get teh proper IOM firmware .I opened one TAC and they are telling TAC doesn't support this we have to contact cisco AS team and we don't have cisco AS team contract.
Regards
Debashis

Dear Walter;
Really appreciated your expert technical advice.
I have one small question as below if you can answer it..
As per the existing setup..
This UCS system is connected with the EMC storage Model:VMAX-1SE Version:5876.
We have no idea if UCS firmware version 2.1(3c) is compatible with the MC storage Model:VMAX-1SE Version:5876..
I have opened the TAC and also went through the Compatibility matrix where it mentioned as attached and to conatct EMC vendor.
We opened case with EMC they are telling contact Cisco and Cisco TAC telling contact EMC.
IS there any way we can know this?
Note as per the attachment:
5. Direct Connect FC/FCoE topologies are supported with this array.
6. Non-default adapter settings are typically required by storage vendors and found on their support list.
7.Multiple array and switch models supported with UCS by the storage vendor are on their support list.
12.iSCSI Boot is supported Both Appliance and Uplink ports are supported unless otherwise noted.
26. Supported for NFS/CIFS access via appliance ports on the Fabric Interconnect

UCS E-Series availability?

In typical Cisco fashion, customers asking for Prices before Cisco publishes to partners the availability...
Anyone have Orderability/FCS info?
http://www.cisco.com/en/US/products/ps11273/index.html
http://www.cisco.com/en/US/prod/collateral/contnetw/ps5719/ps11273/data_sheet_c78-625000.html
http://www.cisco.com/en/US/prod/collateral/contnetw/ps5719/ps11273/qa_c67-625001.html

Hi Wilson,
Cisco Have recently submitted an Expert Webcast: Cisco Unified Computing System (UCS) B series Upgrade & Troubleshooting
https://supportforums.cisco.com/event/12289671/expert-webcast-cisco-unified-computing-system-ucs-b-series-upgrade-troubleshooting
Let me know for any questions / concerns, much appreciated.
Thanks!
Tara

UCS E-Series

Hi
I am testing a isr router with a ucs blade installed but seem to run into some issues. I have the router directly connected to my laptop and are follow the configuration instructions in the configuration guide. I get the following symptoms in any of the configuration / connectivity scenarios…. connecting to one of the router port and mapping that to the ucs, connecting to port g2 on the ucs or connecting directly to the management port. I do configure the unit with the appropriate configs for each of the connection types as per the guide.
Problem 1 – although I am able to ping both the router and the cimc IP I cannot web to the cimc.
Problem 2 – if I try to install esxi (same as I run on our B and C series servers) it gets to about 75% and then halts looking for a network card.
I am obviously missing something here… any assistance will be appreciated
Regards

Hi Wilson,
Cisco Have recently submitted an Expert Webcast: Cisco Unified Computing System (UCS) B series Upgrade & Troubleshooting
https://supportforums.cisco.com/event/12289671/expert-webcast-cisco-unified-computing-system-ucs-b-series-upgrade-troubleshooting
Let me know for any questions / concerns, much appreciated.
Thanks!
Tara

Nexus 5548 to UCS-C series network connectivity.

Hi There,
I am new to nexus world, mainly telecom side. I have a situation where a vendor like to deploy two Cisco UCS-C series servers for voice deployment.
Each UCS C240 M3 server has 4 NICs, 2 nics bonded 802.1q will connect to primary nexus 5k switch and other two bonded will connect to secondary nexus switch. we have a vPC domain and no FEXes so we have to connect these two servers directly to Nexus 5ks.
My question is it possible with teamed nics to coonect to 2 different nexus switches?
Can anyone guide me how can I achieve this design? see attached.
Thanks Much

It will also depend on the Server network settings such as OS, software switch flavor and NIC teaming option on the server.
x- if you run ESXi, then you may check out the following KB article.
http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1004088
x- if you use N1Kv, then you can use LACP or static port-channeling, but be sure to make it consistent on the upstream switches.
hope it helps.
Michael

UCS C series maximum hard drive size

Looking for info on the maximum hard drive size support on teh UCS C series. I have a C200M2 that I added a 4TB drive, I have updated the server to the latest firmware and BIOS however the server shows the drive size is 2TB.

Hi! and welcome to the community mate!
Here is the table that shows the supported disk's PID for the C200 server:
http://www.cisco.com/c/dam/en/us/products/collateral/servers-unified-computing/ucs-c-series-rack-servers/c200m2_sff_specsheet.pdf
If you successfully installed ONE HDD of 4GB and made it work, you were lucky cause I don't see any disk with that size, I have not even seen a disk of that size for UCS yet.
I am wondering if perhaps you installed 4 disks of 1TB and configured them in RAID 1 which would explain the reason for the size to go down to half of the capacity of the array as RAID 1 is a mirror.
Let me know if I misunderstood you.
Rate ALL helpful answers.
-Kenny

Lync 2013 Standard Edition on Cisco UCS E-Series

Hello,
We have a working Lync 2013 deployment:
- Front-End Enterprise Pool consisting of 3 FE servers
- one Edge Server
- one Back-End server
- one Mediation Server
- one IP PBX gateway, where ITSP's SIP trunks end.
Because we have geographically distributed offices, we are considering deploying of branch offices deployments.
Technet recommends to use SBA for branch offices where there are less than 1000 users. But in case of WAN outage, no conferencing will be available for branch users.
Lync 2013 Standard edition branch deployment would offer all Lync features in case of WAN outage.
In every branch, we consider deploying a Cisco ISR G2 router for terminating branch SIP trunks. This equipment have option to add Cisco UCS E-Series blade that supports CPU with hardware virtualization and supports decent amount of RAM (up to 16GB and up
to 48GB).
Have anyone experience with deploying Lync Standard Edition on this equipment - Cisco UCS E-Series blades? In every branch office there are up to 50 - 500 users that will use Lync.
Thanks,
Andrei Moraru Endava

Hi,
I don’t think you can deploy Lync server 2013 on Cisco UCS E-Series blades.
Here is a link below of “System Requirements for Servers Running Lync Server 2013” may help you:
http://technet.microsoft.com/en-us/library/gg398588.aspx
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support

UCS B series fresh install procedure

I will be performing new ucce setup on new UCS B series chasis.
Havent have complete idea like where to start & what all config need to be done on UCS but known on ucs terminology.
can someone through lights on config parameter to start config steps to start with new UCS installation ,followed by any other inputs appreciated.
UCS H/w : UCSB-B200-M3-U
Component mapping Requirement: Each Esxi will carry 6 nodes on it.
How much time requires to setup fresh install of 14 ucs boxes
Thanks
Manz

Hi Manjunath,
Please refer the below links for your current query,
http://docwiki.cisco.com/wiki/Virtualization_for_Unified_CCE
http://docwiki.cisco.com/wiki/Before_You_Buy_or_Deploy_-_Considerations_for_Design_and_Procurement
http://docwiki.cisco.com/wiki/Implementing_Virtualization_Deployments
Hope this helps.
Anand
Please rate helpful posts !!

UCS C series server whether accessible from Linux prompt

Hi UCS Team,
I have UCS c series server.
I am able to check the Fan, power,cooling and equipment and hardware status using the CIMC.
In CIMC I configured the SNMP and check it using MG soft Mib browser tool.
The CIMC query the BIOS for getting the information.
Similarly is there any process to get the BIOS information from the Linux.
Correct me If I am wrong anywhere.
My requirement is to query the UCS C server BIOS information using Linux-SNMP without CIMC.(direct access of BIOS from Linux)
Can I install a Linux supported SNMP client and supported MIBS to query the BIOS level information of UCS using SNMP MG soft Mib browser?

Hi Keny,
I tried to powercycle both servers (c260M2 and C460M2) but still no discovered server and also no logg.
I checked
Rack Server Discovery Policy == immediate
Rack management Connecton Policy == Auto Achnowledged
Chassis/Fex Doscovery Policy == 2 Link and Port-Channel (As I installed 2232PP I moved to Port Channel)
I am running UCSM Version 2.1(1e)
FI 6248 Version 5.0(3)N2(2.11e)
2232PP run on same as FI
I also have a connected 5108 with IOM 2104 running on 2.1(1e) Version.
CIMC Version of C260M2 and C460M2 will be checked tomorrow when my kolleague is in the datacenter.
Server Connection is not really the same like in http://www.cisco.com/en/US/docs/unified_computing/ucs/c-series_integration/ucsm2.1/b_UCSM2-1_C-Integration_chapter_011.html
Because I still have no VIC Card but the connections are the same.
C260 GE LOM1 <-> FEX2 Port 11
C260 GE LOM2 <-> FEX3 Port 11
C260 10 GE LOM1 (PCIE Slot4) <-> FEX2 Port 12
C260 10 GE LOM2 (PCIE Slot4) <-> FEX3 Port 12
GE LOM ist position 13 and 10 GE LOM is position 11 in the techspech of c260
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C260/install/overview.html#wp1243740
C460 GE LOM1 <-> FEX2 Port 10
C460 GE LOM2 <-> FEX3 Port 10
C460 10 GE LOM1 <-> FEX2 Port 9
C460 10 GE LOM2 <-> FEX3 Port 9
GE LOM ist postion 8 and 10 GE LOM ist position 7
http://www.cisco.com/en/US/docs/unified_computing/ucs/c/hw/C460/install/overview.html#wp1243740
With C260 I also tried a reboot with disconnected 10 GE Ports, but also no discoverd Server until now.
Regards Alois

UCS b-series port personality

Hi
I have been studying about UCS b-series, and I have a doubt regarding to the port personalities, what is the difference between the uplink port and the FCoE uplink port??

Uplink port = classical Ethernet
FCoE Uplink = FC over Ethernet (lossless Ethernet); so it's a storage uplink
Uplink + FCoE Uplink = unified uplink (storage (FC over Ethernet) + data (IP over Ethernet)

Just like HP servers, does Cisco UCS C-Series Standalone supports Network Fault Tolerance ?

Just like HP servers, does Cisco UCS C-Series Standalone supports Network Fault Tolerance ? if yes then, where can i find this option
Windows :- 2k8 R2

Just like HP servers, does Cisco UCS C-Series Standalone supports Network Fault Tolerance ? if yes then, where can i find this option
Windows :- 2k8 R2

Does the UCS C-Series Servers supports PCI/e card digium T1/E1

Hello,
Does the UCS C-Series Servers supports/compatible with PCI/e card digium TE407P/TE420 T1/E1.?
The server will be used as Asterisk server.
Thanks
Philip

Hi Philip,
Compatibility will depend on the server model that you have and whether the digium card is a full length, low profile, or half length pcie card. Take a look at http://www.cisco.com/en/US/products/ps10493/prod_models_comparison.html#~tab-a for details. If there are any issues with the card itself once it is installed it will have to go through the 3rd party manufacturer.

Question on UCS C series

Similar Messages

Maybe you are looking for