Question POS point to point with no APS

One side
POS1/0/0
SECTION
LOF = 0 LOS = 0 BIP(B1) = 0
LINE
AIS = 0 RDI = 0 FEBE = 0 BIP(B2) = 0
PATH
AIS = 1 RDI = 2 FEBE = 1119 BIP(B3) = 463
PLM = 4 UNEQ = 0 TIM = 0 TIU = 0
LOP = 0 NEWPTR = 0 PSE = 0 NSE = 0
Active Defects: None
Active Alarms: None
Alarm reporting enabled for: SF SLOS SLOF B1-TCA B2-TCA PLOP B3-TCA
Framing: SONET
APS
COAPS = 0 PSBF = 0
State: PSBF_state = False
Rx(K1/K2): 00/00 Tx(K1/K2): 00/00
S1S0 = 00, C2 = 16
Remote aps status (none); Reflected local aps status (none)
Other end
POS1/0/0
SECTION
LOF = 0 LOS = 0 BIP(B1) = 0
LINE
AIS = 0 RDI = 0 FEBE = 0 BIP(B2) = 0
PATH
AIS = 1 RDI = 1 FEBE = 419 BIP(B3) = 859
PLM = 3 UNEQ = 0 TIM = 0 TIU = 0
LOP = 0 NEWPTR = 0 PSE = 0 NSE = 0
Active Defects: None
Active Alarms: None
Alarm reporting enabled for: SF SLOS SLOF B1-TCA B2-TCA PLOP B3-TCA
Framing: SONET
APS
COAPS = 0 PSBF = 0
State: PSBF_state = False
Rx(K1/K2): C0/15 Tx(K1/K2): 00/00
S1S0 = 00, C2 = 16
Remote aps status (none); Reflected local aps status (none)
My question is the Kbytes what does that mean loss of signal on RX ? Rx(K1/K2): C0/15 Tx(K1/K2): 00/00
There is no Auto protection Switching on this circuit it is straight point to point.

Hello,
the meaning of the K1/K2 bytes are defined in "Telcordia document GR-253—Synchronous Optical Network (SONET) Transport Systems: Common Generic Criteria".
K1/K2 = 00/00 means no APS (respective no APS requests)
K1/K2 = C0/15 means
K1 = 11000000, which translates to "low priority signal failure on protected channel"
K2 = 00010101, which translates to "working channel 1 in 1+1 redundancy, bidirectional mode"
So this can mean, that the provider equipment on one end has APS configured, whereas your euipment has no APS configured. APS is local between your interface and the provider equipment (multiplexer).
Hope this helps! Please rate all posts.
Regards, Martin

Similar Messages

Wi-Fi Access Point with B Channel or Wi-Fi with B Channel

What does Wi- Fi with B channel or Wi-Fi Access point with B Channel mean. Can someone explain me. I am confused

I don't know what your asking. if your talking about 802.11b, that is a standard and you can compare the difference of 802.11b, 802.11a, 802.11g, 802.11n and or 802.11ac. Wireless devices, that means client devices have to be able to support the standard that the access point is using. So if an access point is 802.11b only, the wireless client device has to be able to support 802.11b. If for example, the access point is 802.11b/g/a/n/ac, that means the client has to be able to support at least one of those standards to be able to connect.
Just take a look at the standards, here is a link to a quick comparison.
http://compnetworking.about.com/cs/wireless80211/a/aa80211standard.htm
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

What does the Mouse Pointer with Letter 'M' mean?

Couldn't find any info on this via search, and I'm still a little new to LP8 so pardon this question if it's been asked many times before.
Just wondering what the mouse-pointer with the letter 'M' attached to it means. I notice it pops up when I open songs I made in Logic Pro 6 inside Logic Pro 8.
Thanks,
David

Never ceases to amaze me how many times I answer my own questions on various forums but only, of course, after actually posting it. No wonder it didn't pop up on any searches.
It's the mute tool in case any other newbies stumble upon this post.

Why i am unable to select between 2 anchor points with in a object while dragging with direct select

why i am unable to select between 2 anchor points with in a object while dragging with direct selection tool instead it moves

Another option is to temporarily change your view to outline mode, when your done switch back to preview mode. Ctrl-Y or View>Outline {View>Preview} The menu option will change depending on which mode you are in.
And another option, double click on the object in question to place it in Isolation mode. You can now edit to your hearts content. When done, click on the gray border at top of document.
So as you can see there are multiple ways of accomplishing the same thing.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

Is there any way I can control which specific access point I connect (and stay connected) to from amongst a set of access points with the same SSID?

I'm working from a boat in a harbor in which the ISP has deployed numerous access points around the periphery. All the access points share the same SSID and each is configured to use either channel 1, 6 or 11. From my location, there are over a dozen of these access points "visible" (based on the the output of WiFi Scanner) with a range of RSSI and S/N values that vary over time.
The ISP has told me that the quality of my connection should be "perfectly fine" for any access point with an RSSI value better than -75, but I know from experience that my connection quality is miserable (i.e. < 50Kbps download) for almost all of these, including those with RSSI values better than -75. There is at least one exception, however, which gives me on the order of 2Mbps download, which is "great" in this context.
I've tried using a more powerful USB antenna plugged into my MacBook Air (mid 2011), but as far as I can tell, it really doesn't make much difference. Neither does my location within the boat. The overriding factor seems to be which access point I happen to connect up to.
I should point out that the closest access points are about 75 yards away, with many of them being several hundred yards away or more. I'm guessing that even though the signal strength of some of the distant access points is causing them to get "chosen" some times, the results are unacceptable due to the distance.
I'm hoping that I can determine, through experimentation, which access point(s) provide(s) acceptable performance and then configure my Mac to limit my connection to those points through whatever mechanism I need to use (e.g. channel, MAC id, etc.).

Establishing a wireless connection with a client computer is left to the access point for various reasons. One reason that your Mac may not connect to the strongest access point is that it may have reached a limit of the number of clients it can serve, leaving it unable to accept a connection with another. The limit may not be very large.
Suppose that happens, and your Mac establishes a connection with a more distant access point having a weaker signal. Then, suppose a client drops off the network. Doesn't this mean your Mac will switch to the stronger access point? Not necessarily. The throughput delivered to and from your Mac would have to drop below a threshold specified in the AP for it to drop the client, leaving your Mac free to connect with another one. The reason for this is to prevent rapid switching from one AP to another in an area in which two signals are of approximately equal quality. If that were to occur the frequent and repetitive handshaking between the two devices would slow throughput to zero.
In an environment in which several access points are broadcasting the same SSID, Apple provides no insight as to how it determines which access point to choose. This is the reason I suspect this "choice" is a function of the router, or access point. The connection originates with it, not the Mac.
Now, what would solve your dilemma would be to determine a way to control the access point with which your Mac connects, by specifying the access point's unique MAC address for example. In this happy circumstance, you could maintain an editable "whitelist" or "blacklist" of the harbor's access points and be able to choose which among them you prefer.
I do not believe OS X maintains such a record of MAC addresses though, only those of the routers it uses. If I am correct about that, such a solution is unlikely to exist. Don't let that discourage you from searching for one though... I would concentrate on something like "selecting access point by specific MAC address".
I did find this patent application though:
Roaming Network Stations Using A Mac Address Identifier To Select New Access Point
Perhaps it's a start

Create waveform from a set of points with differtent time intervals

Hello,
I would like to create a waveform from a set of points like this
Time           Data
0                 0
0,5              1
0,6              2
1                 1
2                 0
5                 1
The problem is that the time interval between each points are not the same.
The only idea I found was to create a waveform for each doublet of points with the same rate (100ms) and than to append them together.
Does anybody have a better idea?
Regards,
Risotto.

If you use a Wave From data type, re-sampling is not required.
When using a WF datatype the chart (graph) will pick-up the X value from the t0 of the waveform.
The trick is to just build an array of the single update value and make sure the t0 value is correct.
Re-create this example
and try it for yourself.
Ben
Note: make sure the data you pass is consistant with the data already displayed. If you post a t0 value that is older than what is already displayed, the chart will clear the display and start over.
Message Edited by Ben on 09-15-2006 11:49 AM
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction
Attachments:
WF_Datatype.JPG ‏59 KB

Exclamation Point with Battery

The other day my computer froze when i was loading songs onto my ipod and i was forced to restart my comp, next thing i know all the songs r deleted from my ipod but not my itunes and the same settings r still on my ipod. now when i try to turn it on the apple comes up for a while follwed by an exclamation point with a battery behind it, and my computer or ipod updater wont detect my ipod anymore, does this mean my battery's dead after it only being about 9 months

Please do a full recharge of your iPod with the AC charger - not via your PC's USB

How to play a cue point with mixer

I know how to play a cue point of sound with the method:
sound(1).queue([#member: ... #startTime: ... EndTime: ... ])
How can I transfer the method of cue point using the mixer?
I need to have any hint about this because I must use both cue
point with playrate, at my begginer level of knowledge I know that:
1) I can't use "playrate" with "sound(1).play()" method.
With this method I can use cue point;
2) I'm trying to know If I can use cue point with mixer method.
With this method I can use "playrate" .
It is also for me important to know if it is possible or
impossible to solve this problem in director.
Thanks.

iPhone 3gs, 4 or 4s?
With the former two, just drag the videos to the desktop iTunes and sycnhronize to your iPad. They will be synched to the stock Videos.
With the latter, you can either resize the video to 720p (or less) OR use a third-party app (It's Playing, AVPlayerHD, GoodPlayer being the best choices) to play it back. I'd go with the latter to avoid quality degradation and long-lasting reencodings.

Cfchart CFmx8 charting points with no data

We are having a problem with <cfchart> in CF 8. It
worked fine in CF7.02 with all hotfixes installed. Basically it
plots points where there is no data. some lines have data for 15
points and some for maybe only 13 or 14 points. It fills in teh
missing points with data from the last point that had data.
Notice the last three lines on this chart. At the end of the
line--- where the line goes straight across it is charting data
that doesn't exist.
http://www.bikersites.com/SL/raceSL/secondsbehind.cfm?RHID=31:1
This gets to be a real problem when you look at the following
chart. It gives the races lap times for laps they never completed.
http://www.bikersites.com/SL/raceSL/laptimes.cfm?RHID=31:1
Any ideas? Anyone else having this problem?
This works fine on our development server which had CF7. But
at hostmysite they have cf8.

Having same problem here, with CF9. I have 5 monthly data points for Jan-May 2012. But CFCHART will extend the LINE in the line chart for the June - December 2012 with all ZEROs. This only happens when I'm plotting multiple series, for example if I add a CFCHARTSERIES for all 12 months in 2011.
If I remove 2011, CFCHART only displays the 5 monthly data points for 2012. I'm using two CFQUERIES (Q of Q), one with 12 monthly data points for 2011, and one with 5 data points for 2012 year-to-date. Individually (with 1 CFCHARTSERIES) they plot fine. But when you have TWO CFCHARTSERIES, the 2012 extends the 2012 line with all ZEROs for June-Dec 2012. So you don't get a good year-over-year chart, and I need one that scales, since all the values are between 90% and 100%. Thanks for any help/advice.
Gary

Mimo access points with Static WEP security do not allow connection speeds above 54mbps

I am getting this message:
Access Connections - Mimo access points with Static WEP security do not allow connection speeds above 54mbps
If I switch from WEP to WAP i do not get the message but I still only get 54mbps speed. I have a Linksys Wireless-N Broadband Router. Is there a setting that I am missing???

Yes you need to use WPA-AES or WPA2-AES, or no encryption, to go faster than 54Mbps. This is part of the 802.11n spec.
That's not so bad, because if you have the right 802.11n card and use the right settings you can go up to 300Mbps!
What bites is that the 802.11n card which comes with X-Series ThinkPads is the Intel 4965AGN. It does not support the broader 802.11n 40MHz channel width option, limiting the top speed to 130Mbps .
The new ThinkPads based on the Montevina/Centrino 2 platform will most likely use the Intel WiFi Link 5100/5300 802.11n/WiMax cards, which I hope will fix this, coz I'm going to buy one!
I don't work for Lenovo. I'm a crazy volunteer!

Can pulse measurement.vi measures 2M points with 10ns time interval?

Hi,
I used pulse measurement.vi to measure the pulse duration of waveforms when the waveforms exceed certain threshold level. The data file has 2 millions data points with 10ns time interval. But I got error message saying that
"The waveform did not cross the mid reference level enough time to perform this measurement. Check the signal length, mid reference level, and reference level unit."
I was wondering if pulse measurement.vi is capable of handling such large file or it was due to my paramenter errors.
Thank you for your help in advance.

I realized that I can't really modify the percent level settings or specfication of the pulse measurement.vi. For instance, I changed the percent level setting to peak instead of the default auto select. After running the VI unsuccessfully and I reopened the pulse measurement.vi, I saw the percent level setting was set to auto select again instead of peak method. I have attached the image of the block digram and a very small part of the waveform data. I hope you can open both.
Thank you.
Attachments:
pulse measurement.doc ‏45 KB
example.txt ‏2 KB

Anchor points with pen tool askew

Hey everyone, I have been using illustrator for about 5 years now and this has never happened to me before. I use CS4 and i opened it today to trace a logo and out of nowhere, whenever i go to connect a point with the pen tool, it makes a point about a quarter of an inch in the opposite direction of where i clicked down. Usually I can make a point, then try to connect it with another and it goes exactly where i clicked down for point #2...now it's impossible to correctly trace anything since I have little control over the pen tool anymore.
I read in another forum when researching this problem that in in View > snap to point may cause this but even after unselecting it, i still have the same problem. I also tried resetting Illustrator like I read may help and nothing. I can't find the presets folder on my computer I did the key combination while opening the program.
Thank you for your time!
-Melissa

Melissa,
It could be a preference corruption or a disturbance from other applications or something similar.
To reset the former the former, you may try to Move the folder with Illy closed, or just press Ctrl+Alt+Shift/Cmd+Option+Shift during startup (the latter is easier but changes your preference settings to defaults (spoiling any customized settings, and it may be necessary to perform the more thorough Move).
To solve things in case of the latter, you may have a look at the relavnt items, including 7, in Other options.
Or it could be something else.

Lasso tool control point with delete keyboard shortcut in PS CC

Hello,
I can not remove lasso tool control point with delete keyboard shortcut in PS cc. please help

it's a bug, view this thread
http://forums.adobe.com/message/6027062#6027062

Update Measurement Point with new Position

Hi,
I need to update existing measuring points with new measurement positions. I was looking at FM "MEASUREM_POINT_RFC_SINGLE_002", but don't know how to pass the new Measurement Position to that.
Can anybody please let me know how has already implemented this?
Thanks.

I was looking at FM 'MEASUREM_POINT_DIALOG_SINGLE' to update Masurement Point.
I wrote the code like this. But it's not updating the Measurement Point with the new position.
Not sure if I missed anything.
Pelase help.
Thanks.
PARAMETERS: p_point type imrc_point,
                         p_psort type imrc_psort.
DATA: l_rimr03 type rimr03,
       l_ind(1) type c.
l_rimr03-mandt = sy-mandt.
l_rimr03-point = p_point.
l_rimr03-psort = p_psort.
BREAK-POINT.
CALL FUNCTION 'MEASUREM_POINT_DIALOG_SINGLE'
EXPORTING
   ACTIVITY_TYPE                  = '2'
   MEASUREMENT_POINT              = p_point
   NO_DIALOG                      = 'X'
   IS_RIMR03                      = l_rimr03
IMPORTING
   INDICATOR_UPDATE               = l_ind
EXCEPTIONS
   IMPTT_NOT_FOUND                = 1
   TYPE_NOT_FOUND                 = 2
   OBJECT_NOT_FOUND               = 3
   NO_AUTHORITY                   = 4
   POINT_IS_REFMP                 = 5
   POINT_IS_NOT_REFMP             = 6
   OTHERS                         = 7

Question POS point to point with no APS

Similar Messages

Maybe you are looking for