Question regarding ONT connection via Ethernet and Cable cards

Hi,
We recently upgraded to Fios Quation 150Mbps/65  plan. We are not getting the advertised speeds (we only get like 5mbps upload) so verizon is sending a tech to switch the ONT connection from coax to ethernet.
I have 2 questions regarding this new setup:
1. If the ONT communicates with the Fios Actiontect router via ethernet instead of coax from now on, How will the set top boxes and Tivo-esque cable card powered device I currently have connected to coax, talk to the verizon system from now on, if coax is taken out of the equation? Will fios signal still flow through the internal coax wiring of the house? And moreover, I was under the impression that coax was the way set top boxes communicated and derived independent ip addresses from the Fios router, for on deman purposes and what not. How will this work from now on?
Quiestion 2.
Right next to the wall where the ONT sits, theres's a basement office where we have a PC that connects to the Fios system  via an Actiontect MoCa adapter (ECB2500C) which I assume derives it internet connection from the Fios Actiontec router which sits upstairs in the living room. 
Again, with the Coax about to be disabled next Friday in favor of ethernet connection from the ONT, I assume this PC will be left without internet because of the lack of internet signal in the coax? Is this correct? 
Question 2.5 If my above assumption is correct, since this office is right on the other side of the wall where the ONT sits outside the house, would it be possible to run an ethernet wire through the wall that connects straight from the ONT to an ethernet switch inside the office, from which I would derive a connection for this basement PC (properly firewalled of course) and then, from said switch, continue running the ethernet wire that would ultimately reach the Actiontec Fios router upstairs from which the rest of the house derives it's internet?  and would this setup affect in any way the propper functioning of the cable boxes in the house?
I'd appreciate your input and any help you can provide so I can have a ballpark idea of what to tell the Fios guy to do when he comes on Friday.
Cheers.
Solved!
Go to Solution.

It's not valid to have two devices connected to the ONT, PC and VZ Router.  Must be a single device. The ONT locks onto the MAC Address of the first device it sees. Since you have TV you should have the VZ router as the internet facing router.
Other options:
1.  Have the VZ Router located next to the PC in the basement and then use Wireless for all other PC's.
2.  Have the VZ Router located next to the PC in the basement but run one wire upstairs and connect a switch where other PCs and devices can connect via a wire.
Hope that helps.

Similar Messages

  • I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. My question is I now wish to add a second Airport extreme but am considering a hard wire connecti

    I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.  Can my network operate properly to extend the network with both a wireless and wired extend functionallity?

    I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.
    Excellent plan.
    Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
    Yes, but don't get confused about the second AirPort Extreme, as it would not be configured to "extend" a wireless network.....it would be configured to "create a wireless network" using the same wireless network name, security settings and password as the Time Capsule network. Configure the second Extreme in Bridge Mode.
    This Apple support document will show you how to hookup and configure the second AirPort Extreme:
    http://support.apple.com/kb/HT4260

  • HT2497 I just purchased the 2TB TC and set it up on bridge mode to my att verse which is connected via ethernet cable.  The TC is continually blinking amber and an error message states that a wireless network cannot be found but the uverse is functioning

    I just purchased the 2TB TC and set it up on bridge mode to my att verse which is connected via ethernet cable.  The TC is continually blinking amber and an error message states that a wireless network cannot be found but the uverse is functioning great.  The network name I assigned to the TC is also not appearing among available networks.  How do I remedy this, please?

    What OS on the computer you are using to setup the TC?
    Did you turn on ipv6 for wireless to link-local... this is essential for network access now??
    Try power cycling the network.. start up in correct order.. uverse.. 2min wait.. TC.. 2min wait.. computer.
    No luck factory reset and start over. Use ethernet cable as well to the computer to help it.
    No luck I can show you manual method.

  • Out of the blue, my ITouch is unable to access my wireless network ONLY when my PC has been turned on (PC is connected via Ethernet cable, and has no wireless capability as far as I know).  What gives?  It works fine when the PC is off.

    Out of the blue, my ITouch is unable to access my wireless network ONLY when my PC is on (the PC is connected via Ethernet cable, and has no wireless capabilities that I know of).  What gives?  When the PC is turned off, everything is totally fine.  I\m stumped. 

    Does the iOS device connect to other networks?
    Does the iOS device see the network?
    Any error messages?
    Do other devices now connect?
    Did the iOS device connect before?
    Try the following to rule out a software problem:                 
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on your router
    .- Reset network settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - Wi-Fi: Unable to connect to an 802.11n Wi-Fi network       
    I suspect a problem with your router. Try changing the security. First use no security as a test.
    - iOS: Recommended settings for Wi-Fi routers and access points
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar

  • I have an HP LaserJet 8150N that I am trying to get connected via ethernet cable directly to my iMac. I always had this printer connected via a network so I don't know if I am able to connect directly with a cable since it is a network printer.

    I have an HP LaserJet 8150N that I use for my work and I have had this printer for ever and it is one heck of a work horse! I am trying to get it connected via ethernet cable directly to my iMac. I always had this printer connected via a network so I don't know if I am able to connect directly with a cable since it is a network printer. I have tried to reconfigure the printer using the JetDirect menu giving it a new IP address but still no luck. If anyone could help me through this issue I would appreciate it.

    moonlightcaravan wrote:
    Second, seeing "connecting" and connection failed is normal. You must click on "Connect As" in the Finder window and then enter the username and password for the admin account on the other computer. That should fix things.
    Thanks for responding.
    When does clicking on "Connect As" happen in the process above?
    After step six? Seven?
    After the connection has failed?
    Is this the FInder window that shows the icon of the computer you want to copy the file from?
    You should see "Connect As" in the Finder near the top right of the window as shown below:
    !http://blog.brothersoft.com/wp-content/uploads/2008/11/howto_copy_files_to_or_from_your_iphone02.jpg!

  • MB Air cannot see TC 1T '09 while connected via WiFi and Ethernet.

    I have a TC 1T 2009 7.4.1 that I have set up successfully with MB Pro and MB White. However I cannot set it up with MB Air v.1 which is connected to TC via WiFi AND Ethernet cable. Internet is fine (Safari) but no TM - when I run APU 5.4.1 it cannot discover the TC it is connected to.
    I tried connecting after hard-reset (poke/power on), it would see the TM but then hang forever reading the configuration. So I set it up with MB Pro and MB White and both are now working fine with TC/TM. Then I tried MB Air and it failed.
    The TC is connected via ethernet to Sagem router (bridged mode) which supplies WAN and DHCP, it has its own WiFi as well.

    And by the way, Hi Everyone, how rude of me not to greet you in the post.
    Thanks for any help!

  • My Apple TV will not update to the latest software, dose anyone know what the problem is, I've reset, tried to do it wirelessly as well as while connected via Ethernet cable.. Both have resulted in the same message!!

    My Apple TV will not update to the latest software, dose anyone know what the problem is, I've reset, tried to do it wirelessly as well as while connected via Ethernet cable.. Both have resulted in the same message!! Update unsuccessful, current software version is 5.1 (5201) . I've rented a movie recently and does not appear in my movie list, but I have been charged for this movie, can someone help me out with these issues.

    If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
    Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
    Connect the micro USB cable to the Apple TV and to your computer.
    Reconnect the power cable (only for Apple TV 3)
    Open iTunes.
    Select your Apple TV in the Source list, and then click Restore.
    If when you choose restore you get a message that the device cannot be found, download the file below
    Apple TV Software Restore 5.1.1 (2nd generation)
    Apple TV Software Restore 5.1.1 (3rd generation)
    Then hold down the option key while choosing restore and select the downloaded file when prompted.

  • Connecting a powerbook G3 to the internet via ethernet and a DSL modem. Does the G3 have the ability to do this?

    I am trying to connect an older powerbook G3 (M4753) to the internet via ethernet and a DSL modem. Does the G3 have the ability to do this? I'm having alot of trouble. G3 Dialog box states the DHCP server will populate IP address, etc. It does not. The G3 also insists I enter the DHCP client ID.

    Anything useful in the following articles?
    http://support.apple.com/kb/TA20782
    http://support.apple.com/kb/TA20785
    Jan

  • Connecting to Time Capsule via Ethernet AND wireless

    I have connectivity through an Ethernet network to which my Time Capsule is connected. I connect wireless to TC, but another Mac which is out of wireless range -but still in the same Ethernet network,- cannot connect to TC via ethernet. Is there a way to have access to TC both wireless and via ethernet?
    Thanks
    Nilde

    Hello Nadjia. Welcome to the Apple Discussions!
    Is there a way to have access to TC both wireless and via ethernet?
    Yes, the TC supports both wireless and Ethernet clients simultaneously. Let's double-check the Built-in Ethernet settings on the Mac that you are trying to connect via Ethernet.
    System Preferences > Network > Show > Network Port Configurations
    o Verify that a Built-in Ethernet option exists. If it does not, click "+" to create one. (Note: If you are unable to create a Built-in Ethernet configuration, the Ethernet card in your computer either doesn't exist or it is not recognized.)
    o Verify that Built-in Ethernet is at the top of the list. If it isn't, you can drag it to the top.
    Advanced > TCP/IP tab
    o Configure IPv4: Using DHCP
    o Configure IPv6: Off
    Advanced > DNS tab
    o Verify that your ISP's DNS server(s) appear. If they do not, click "+" add them.
    Advanced > Proxies tab
    o Configure Proxies: Manually
    o Select a proxy server to configure: <All proxies should be unchecked unless you specifically require a proxy for Internet access.>
    o Exclude simple hostnames (unchecked)
    o Bypass proxy settings for these Hosts & Domains: <leave blank>
    o Use Passive FTP Mode (PASV) (checked)
    Ethernet tab
    o Configure: Automatically

  • Time Capsule connected to internet via ethernet and static IP address

    Hi! I'm at my wits end and getting no help from my IT department. I want to use my Time Capsule to create a wireless network within my office. I can directly connect my TC to the internet via ethernet and an assigned static IP address. However, doing so I'm unable to connect to the internet using the created wireless network on my laptop. I've tried using the bridge option for sharing as well as the "sharing an IP address" and neither configuration is working. any thoughts?

    I have the same setup; my ISP uses static IP only. No probs configuring a LinkSys router but with TC it's not obvious where to plug in the info. Can't ping the TC router via IP address to setup directly like the LinkSys which would be simple. Is the out of box router address really 10.0.1.1 on the LAN side? I want to use the 192.168 sequence and have changed it but still no success as I can't determine where to put the static IP! Can you give me something specific? By the way, it works fine thru the LinkSys router in Bridge mode.
    Thanks,

  • IMac to Time Capsule via Ethernet and wireless to MacBook

    Hi, here was my previous situation:
    MacBook connected wirelessly to TC for Time Machine. TC was not linked directly to router, but for extending the network.
    Now I have a new iMac which I connected via Ethernet to the TC to use for Time Machine and external storage for iTunes. That works fine, however...
    The TC is no longer part of the wireless network, so my MacBook can not connect any longer.
    Is there anybody who can help with this? Tx very much in advance and best regards, Marc Dierens

    If someone comes across this post, any help would be apprciated. i have the same issue. The time capsule is attached by ethernet to cable modem. The time machine is also connected by ethernet cable to my G5. The time capsule shows up in airport utility. I also have internet and mail. The Time capsule network is also seen by my wifes macbook pro and she has internet.
    However, the time capsule does not show up in my sidebar or on my desktop and it does not show up as an option as the backup disk for time machine - in fact no disks show up.
    Help,
    Liam

  • Powerbook G4 can't connect via ethernet but connects via airport

    We have a small office network connected to an Efficient Networks DSL router that's managed by our isp. The router has 4 ports and a linksys 8 port switch is connected to one of those ports. Another D-Link wireless router/switch is connected to another port.
    2 i-macs connect without problem via ethernet cable. They are set to DHCP and get 192.xx private addresses. Both run 10.4.5. Another older imac running 9.2.2. also has no problems.
    I recently purchased a powerbook G4 and it will not connect via ethernet to the Efficient networks router. At first it was connected to the linksys, so decided to connect it direct to the Efficient Networks router. With DHCP, it acquires a 169. internet address which is self generated (i.e. no real connection). I tried to give it a static private address (talking to the isp provider). They could see the powerbook but saw all zero's (presumable mac address). By the way the Powerbook works perfectly at home connected via ethernet cable to a D-Link router connected to a cable modem so it's not a physical problem. I even checked the ethernet cable I used in the office with another computer - no problem.
    When I switch to airport in the office, the powerbook connects to the network and the internet. I get some strange warning messages showing the server's and the router's private ip addresses. I click ok, and the powerbook finds an unassigned private ip address. It's the only way it will work, but it causes problems, because I can't connect to one of the network printers. Speed also isn't great.
    Can anyone give me advise how to proceed. I am no expert on this stuff so keep it as simple as possible.
    Tks

    Tim,
    Thanks for your help. Here's what I've done before reading your e-mail. The D-Link DI-524 wireless router is connected to the Effiicent Neworks DSL router as you mentioned. One ethernet port of the EFF.Net. router is connected to the WAN port of the DI-514.
    Because I have a D-Link router at home which works flawlessly with my powerbook, I decided to connect the ethernet cable of the powerbook to the D-Link which has 4 ethernet ports. Lo and behold, the powerbook acquired a private ip address and connected to the LAN and internet!
    When I connected the powerbook direct to the Efficient Networks router, it could not communicate. I believe that there must be some software incompatibility between the powerbook and the Efficient Networks router. By connecting to the D-Link, the D-Link assigned an ip address to the powerbook, and it could connect to the server, lan, etc..
    Only problem is that I have a Brother network printer that cannot connect to the powerbook. My powerbook cannot find it on the network. Because there is a linksys switch connected to the efficient networks router's third ethernet port, maybe as you said, going through the D-Link via DHCP (when the Linksys is also acting as a DHCP server, might cause this type of problem. What do you think?
    As a final note, other imac G5's connected to the linksys switch (which then connects to the Efficient Network's router) have no problem connecting to the lan or internet and have no problem connecting to any of the printers. When I put the powerbook on that switch, I could not connect to the internet - i.e. whether connecting via the lynksys switch or direct with the efficient networks router - same results: no internet connection whether manually or via DHCP.
    So the imac G5 has no problem with the efficient networks router but the powerbook G4 hits a brick wall. The G4 likes the D-Link router. I am concerned (and I will have to check this) that if I turn off the dhcp server feature from the D-Link, that whatever software issue crops up between the powerbook and the Efficient Networks router, will rise up again, because the D-Link will act like a simple switch (just like my linksys switch), and we'll be back to square zero. In any case, no harm in trying. This may be the cause of the Powerbook not seeing that Brother printer (even though it sees another printer and other macs).
    Having spent hours reading about network problems, I think it's safe to say that macs have problems with certain routers. Why a G5 works and a powerbook G4 doesn't is beyond me, but clearly software must play a role.

  • IBook G4 Can't connect via Ethernet?

    While we were away lightning took out several devices. Among them was the Airport Extreme Base Station and the cable modem. The modem has been replaced. I have an iMacG5 and an iBookG4 both running 10.4.11. The iMac can establish a connection via Ethernet (all this happened yesterday so I have yet to replace the Airport). The laptop apparently won't accept an IP address from the router/modem and won't connect to the internet.
    I did see a message saying that my network settings had been changed by another application but don't know if this figures in the mix.
    Anyone have any ideas how I ought to approach getting the iBook back online?

    I did see a message saying that my network settings had been changed by another application but don't know if this figures in the mix.
    Anyone have any ideas how I ought to approach getting the iBook back online?
    I think you ran across the security update bug in 10.4.11 the deals with an ethernet connection. Here is the workaround:
    http://discussions.apple.com/message.jspa?messageID=8185915#8185915
    Here is more of the story:
    http://discussions.apple.com/thread.jspa?threadID=1730909&tstart=0

  • Can't connect via ethernet after iBook wakes up from sleep

    I'm running 10.4.0 on a 1.33 GHz G4 iBook. Since buying the computer in 2005, I've been connecting to the internet in various locations via AirPort, though I have hooked my iBook up to ethernet connections in the past and had no problems.
    Recently I moved to a university where I must connect via ethernet, as the wireless network doesn't extend to the areas where I do most of my work. I bought a new cable. Much of the time, my connection is fine. But frequently I am unable to connect to the internet at all via ethernet, and I've noticed that it's always after I've woken the computer up from sleep. I've tried various ridiculous "kick the car and maybe it will start" techniques like unplugging the cable at both ends and waiting, restarting five or six times in a row, etc., and it starts connecting eventually, but I have NO idea why or why not. When I check my network preferences, I get the message "Built-in Ethernet is currently active and has the IP address [xxx.xxx.x.xxx]. You are connected to the Internet via Built-In Ethernet." But I'm not. What's going on here?

    Sorry, meant to indicate an IP address without giving the exact numbers, and it came up as an HTTP address. My network connections system preference panel indicates a normal IP address. (And it's not self-assigned.)

  • Connect via ethernet but wireless for internet

    I don't know why, but my apple tv seems to have forgotten how to connect to the internet and I can't make it remember, lol. Now I will stress, this used to work, and I don't know why it suddenly doesn't work anymore...
    Basically I have wireless set up at home for the internet. However, I connect to my apple tv via direct ethernet cable between my imac and the apple tv itself. I have set up internet sharing in preferences to share my airport connection over ethernet, which my apple tv used to be able to use ok to connect to the itunes store/you tube, etc. However, it now can't. I had some trouble with it this morning where it wouldn't connect to the ethernet network at all, although it now does. However, it no longer uses the iMac as it's router and I can't seem to figure out why. Can anyone help?
    Thanks!

    Chris Johnson2 wrote:
    We have one MBP (10.5.8) that is able to connect to our network via Ethernet and use all services. But, when it connects via Airport, it will connect to the wireless router, but will not connect to the Internet or the network...
    You might try the three suggestions in the second message of this thread:
    http://discussions.apple.com/message.jspa?messageID=10445592

Maybe you are looking for

  • Error : 'Tax Jurisdiction is not determined' while creating sales order

    Hi, I'm creating a sales order using the BAPI : BAPI_SALESORDER_CREATEFROMDAT1. I'm passing the following values in ORDER_HEADER_IN parameter: doc_type,sales_org,distr_chan,division,po_method,sales_off,req_date_h,data_type,purch_no,purch_date,price_d

  • Itunes 10.5 crashes with no error when trying to play any music, video, or import/scan from the library folder on the compter with Windows 7 Pro.

    Fresh install with all older itunes un-installed as well as other Apple software. Now cannot get any songs, videos, or even scan library folder for songs to work on the computer. itunes just simply crashes with no error comments. This is itunes 10.5

  • ICloud Back Up?

    I had a iphone 4 with a cracked screen, Backed it up to icloud before heading to Apple store for a new one, Contacts was turned on for the back up to Icloud, After purchasing the replacement I restored from the icloud back up but all my contacts are

  • Making a DVD in IDVD

    Ok I have tried to make a DVD with IDVD about 14 different setting and they all have something wrong with the DVD. The fonts look like someone had eaten about the edges, or the whites have little spike lines in them. the wipes would look like I didn'

  • Auto login into workspace task

    Hi, In Live Cycle Process a form is assigned to particular user using Assign Task. This will trigger a mail to the concerned user with the URL for going to the task directly.However on clicking this URL, workspace prompts for User authentication. Onl