Question regarding the use of Cisco Aironet 1140 series

We are looking at deploying some of the Cisco Aironet Access Points as standalone. We are essentially setting up a hotspot. They will mainly be in conference rooms at each of our field offices so visitors attending our meetings can have internet access. Do clients have to use Cisco wireless adapters in order to connect
to any of Cisco Aironet Access Points or can they use whatever wireless card they have as long as it supports the bands available?
Thx in advance for any advice given.

Any product which displays the Wi-Fi Certified logo, including everything from Cisco, should interoperate with any other Wi-Fi Certified gear.

Similar Messages

How to load a boot image to cisco aironet 1140 series after missing boot image

Hi all,
I need a solution for this. When i switch my cisco aironet 1140 , it s blinking with red light .and gives a message "no boot image to load".
When i tried next time, by pressing escape it shows this message that i have mentioned below.
ap:
ap:
using eeprom values
WRDTR,CLKTR: 0x83000800 0x40000000
RQDC ,RFDC : 0x80000035 0x00000208
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0x40000000
RQDC, RFDC : 0x80000035, 0x00000208
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialized
PCIEx: initialization done
flashfs[0]: 1 files, 1 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 1536
flashfs[0]: Bytes available: 32383488
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 28:94:0f:d6:c8:62
Ethernet speed is 100 Mb - FULL duplex
The system is unable to boot automatically because there
are no bootable files.
C1140 Boot Loader (C1140-BOOT-M) Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Tue 18-Oct-11 14:51 by prod_rel_team
ap:
So , now my question is how to load the boot image ? From where will we get this ? OR
I m also having another Cisco aironet 1140 , Can i get bootimage from that . Kindly let me know the solution from genius ?

Take a look at this link as it should have the info you need
https://supportforums.cisco.com/docs/DOC-14636
Sent from Cisco Technical Support iPhone App

A question regarding the use of multiple CSS templates

Hello,
I use Dreamweaver CS3. I tried to find information about this online, but I cannot seem to find anything at all. I was wondering if it is possible to use a completely differently designed template for a separate part of a website. From a marketing perspective, I understand that this concept may be impractical, because all websites should have consistently arranged information. However, the website I wish to change is not my own small business in any way. It is the website of the company that I work for, and it is a world-renown organization. Many university students access this website everyday. It was recently brought to my attention, that a proposed "brand-new" blogging section is going to be included in our website, and it was to have a different layout. We wish to use the same domain name, and simply change the style of the other part of the website.
I believe what one must do, is make sure that the .dwt (template) file points to a different CSS file, than the original one. Is this correct? The only reason that I have not tried this is because I am not sure what risks will be involved. It is also impossible to make a new page "from template", and then change the tinted uneditable text, so that it points to a different CSS file. Maybe you make a new CSS file and ensure it is in the same directory as the standard CSS file..? And when you click File-->New, you select the new template?
Any help or advice would be greatly appreciated! Thank you to everyone who contributes or even reads this. Thanks again for coping with the many details of this message.
Kind regards,
Mr. V

I think you already know the answer to this. You need to have two unique Templates and two external stylesheets. For this discussion let's call them Main.dwt and Main.css - for the main site sections. Sub.dwt and Sub.css for the subsite. You can copy and paste the code from one file into a new blank page, then make required changes to it and Save As "Sub..."
Link Main.dwt to Main.css. Link Sub.dwt to Sub.css.
To create a new page from Template, Click File > New > Templates Tab and select one.
Nancy O.
Alt-Web Design & Publishing
Web | Graphics | Print | Media Specialists
www.alt-web.com/
www.twitter.com/altweb
www.alt-web.blogspot.com

Question regarding the use of Built-in Bridge SIP call setup to recording device

We have an application that uses Built-in Bridge (BiB) to setup a SIP call to our recording application. Recently the topology of our network was changed and for some reason the RTP for the call is not being sent. What appears to be happenning is that the SIP messages are sent from the UCCM and once the call is established we get an end call event.
We are not sure how to troubleshoot our network to determine the root cause. Any pointers will be appreciated.
Thanks.
-Arun

Hi
Did you ever figure this out? I am having an issue with recording calls to the PSTN from 9971 SIP phones. Station to station calls seem fine, and 7945 phones running SCCP seem fine to the PSTN.
Thanks,
Aaron

Cisco Aironet 1100 series wireless access point software update!

Hi,
I have a wireless network using 2 cisco aironet 1100 series access points.
From time to time I have problems with connecting a device (Laptop,PC,)to the wireless network.There are onther wireless netwotk that operate around and might be using the same channel.Someone else created the wireless network and I do not know how to access it now to check the configurations on change something.
I cannot conncet my iPhone to the network and I beleive that a software update might solve the problem but I do not know how to do it and where to download it from.
1. How can I update the software and where from?
2.How can I ensure that thare are no interferences and conflicts?
3.How can I ensure that no onther wireless network around is using the same channel?
Thank you in advance.

Sounds good to me. Are you having problems?
Please remeber to rate all replies

Cisco aironet 2600 series AP configuration with windows 2008 R2 Radius server.

I want to know the configuration of Cisco aironet 2600 series AP with windows 2008 R2 Radius server.
I have
1. AD & DHCP Server
2. Cisco Aironet 2600 Access Point.
I want to connect wifi devices through this AP. Authentication should be through Radius server and AD.

Hi ,
Below link should support your requirement
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/116584-configure-wirelesslan-00.html
Minimal command : -
AP(config)# aaa new-model
AP(config)# radius-server host 172.20.0.1 auth-port 1645 acct-port 1645 key XXXXXX
AP(config)# radius-server deadtime 10
HTH
Sandy

I have 2 questions regarding the iphone 5. 1 How do i get my yahoo mail set up. I tried the setting it up as both a yahoo mail and other mail. 2. I seem to have lost my notes on my iphone 5 but I have them on my ipad. How can I use cloud to sync my notes?

I have 2 questions regarding the iphone 5. 1 How do i get my yahoo mail set up. I tried the setting it up as both a yahoo mail and other mail. 2. I seem to have lost my notes on my iphone 5 but I have them on my ipad. How can I use cloud to sync my notes?

I will address your second question.
First, make sure your iPhone and iPad have absolutely identical Apple IDs. If they do, use that Apple ID in Settings > iCloud on your iPhone to select the "Notes" option. Lo and behold, all your iCloud notes should appear on your iPhone.

I have read all the questions regarding the "Can't send photo using iMessage".

I have read all the questions regarding the "Can't send photo using iMessage". I followed everything and check everything that was in it. It's still the same. I am still not able to send a photo. It started happening last week. It was fine before that. There is no error message.
It will try to send but it will get stuck just before it sends
and the red ! will appear with the "Not Delivered" status.
When i tap on the !, it just says "This iMessage was not delived".
No other message or photo is sending as the same time as the photo.
I did reset it, I checked the email address, removed it as well. Turned it off then back on. Signed out and signed back in. Wi-Fi strength is very good. iOS is 6.0.1. I checked for updates, it is up-to-date I also checked a link http://support.apple.com/kb/TS2755. It did not help at all.
What's wrong?!?!?!?!

It is not a matter of reconsidering the decision. There are unsolveable technical problems with trying to run a program such as Firefox on Blackberry OS. We would need Blackberry to distribute a tool similar to Android's NDK to run on Blackberries.

Configuring Cisco Aironet 1140 for Radius and setting up a Radius server

guys i need some help setting up my Radius to work with cisco aironet 1140, i am new at this however i was tasked with setting up a Radius server and setting our AP with WPA2- enterprise so users can log into our AP using AD credentials.
When i try to setup on the AP a new SSID i do not see the option for WPA2- enterprise?

Here are other links with examples:
https://supportforums.cisco.com/thread/331581
http://targetcisco.blogspot.com/2011/03/cisco-autonomous-access-point.html
http://downloads.avaya.com/css/P8/documents/100041614
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Cisco Aironet 1140: 3 of our 4 are always hanging

Our office has 4 Cisco Aironet 1140 access points mounted on the ceiling. They are all powered via PoE. Every few days 3 of the 4 access points hang and have to be rebooted. When they hang I am not able to connect to their web interface to check the logs. The fourth, for some reason, always seems to stay alive.
I checked the configuration for all AP's and "Hot Standby" is disabled
They are all using static IP addresses. I've tried 2 different banks of static IP addresses and 3 of 4 still hange so I don't think this is an IP conflict
I have saved the configurations and compared them and they are all identical, where possible.
They all have software version: 12.4(21a)JA1
They all have bootloader version: 12.4(23c)JA1
I have tried to download the latest software/firmware, but unfortunately I do not have a valid service contract in place with Cisco and therefore can't download the latest version. All of our CISCO hardware was purchased from Amazon resellers and they can't seem to help me with this. I have also tried to contact Cisco and they can't seem to help either. If anyone has a suggestion on how I can get a valid service contract that information would also be very helpful!!!
Does anyone have any ideas why 3 of our 4 access points would hang? When they hang, I can't login to the web interface and the logs seem to reset when I reset each access point. I have also set up an rsyslog server and I don't see a log entry that would indicate a problem.
Any ideas?
Thank you

Here is the config for one of the AP's that keeps hanging:
! Last configuration change at 09:18:05 -1000 Mon Jan 30 2012 by admin
! NVRAM config last updated at 09:18:05 -1000 Mon Jan 30 2012 by admin
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname XXX2
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
clock timezone -1000 -10
ip name-server 8.8.8.8
ip name-server 8.8.4.4
dot11 syslog
dot11 ssid XXX2
   authentication open
   authentication key-management wpa version 2
   guest-mode
   wpa-psk ascii 7 01234567890123456789012
username admin privilege 15 password 7 01234567890123456789012
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid XXX2
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.100.252 255.255.255.0
no ip route-cache
ip default-gateway 192.168.100.1
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
snmp-server community MyCommunity RO
bridge 1 route ip
line con 0
line vty 0 4
sntp server 192.43.244.18
sntp broadcast client
end

Hello, I have a question regarding the sharing/exporting on imovie. Whenever I click the share button all the normal options pop up, but when I actually click where I want to share it to nothing happens. If you know what's wrong please let me know.

Hello, I have a question regarding the sharing on iMovie. I have just recently purchased an Elgato Gaming Capture HD and I then finished my recording with that and put it into imovie. I worked long and hard on the project and when I go click the share feature on iMovie all the noral options pop up and when I actually click where I want to share it to nothing at all happens. If you know what is wrong/ what I am doing wrong please let me know.
Thank you.
PS: I am using iMovie 10.0.6.

/*line 957 error */
     public void select()
          for (count = 0; count <= p; count ++ )
               if(P[count] != null){ /* validation */
               m = (int)(P[count].getX());
               n = (int)(P[count].getY());
               if (Math.pow(-1, m + n) == 1)
                    piece[m][n].setBackground(wselect);
               else
                    piece[m][n].setBackground(bselect);
          step = 2;
     }

Some simple questions regarding the Xcode.

I have some preliminary questions regarding the Xcode (objective C):
What is the difference between the programming files followed by .h and .m?
What does an asterisk * followed by a text mean (i.e. *window;)?
Is there any source that briefly explains the most common codes with examples (nsstring, nsarray, iboutlet, inaction.....etc)?
Any other tips will be highly appreciated.
Many thanks.

Xcode is the IDE.
Objective-C is the most common language used within Xcode.
UIWindow *window ..... the * means return the address of the instance variable 'window'.
An * is called a pointer to a variable.
Everything you need is explained here: https://developer.apple.com

Question regarding the "mcxquery" and "dscl -mcxread" commands:

Question regarding the mcxquery and dscl -mcxread commands:
Does anyone know why the mcxquery and the dscl . -mcxread commands don't show any info about MCX managed login items & printers? The System Profiler's "Managed Client" section does. Id like to see info regarding managed printers and managed login items using the mcx tools. I have Mac users running 10.5.2 with both login items and printers that are pushed out to them via MCX. The System Profiler app shows all of their policies, but the dscl . -mcxread and mcxquery tools dont. Why not?
-D
Message was edited by: Daniel Stranathan
null

How do you "call procedures/functions" without sql code? You need at least the call statement like
{call myProc(?,?,?)}that you wrap into a CallableStatement.
Other than that: when you switch off autocommit, you need to call commit/rollback at the end. Usually, if you don't commit/rollback a non-autocommitted connection, the transaction get's committed/rollbacked when you close the connection - that depends on the JDBC driver. But it's never a good idea to ommit the commit/rollback calls on a non-autocommit connection. Usually you enclose your code in a try/catch block like this:
con.setAutocommit(false);
try {
   con.commit();
} catch (Exception e) {
   con.rollback();
} finally {
    con.setAutocommit(true); //or:
    con.close();
}

Question regarding the Transformation activity in BPEL

Hi,
I have a question regarding the Transformation activity in BPEL.
I have a database adapter that uses a PL/SQL API. The API returns two tables of nested objects and it automatically generates a schema for me based on the outputs structure. I need to use the Transformation activity to map both these out parameters to root element in the destination.
The element in the destination is "unbounded". Please take a look at the following screen shot -
http://www-apps.us.oracle.com:1100/~rvishnuv/transform1.gif
From the screen shot, you can notice that I have two XML segments X_TEST_TBL and X_TEST_TBL1 in the source and I have one GLOGXMLElement ("unbounded") in the destination. I need to map each of the source elements to the same destination. Then internally, I will be mapping the elements of X_TEST_TBL to "Location" segment/element and the elements of "X_TEST_TBL1" to "ItemMaster" segment/element. If I try to use "foreach" and map second
element "X_TEST_TBL1" also GLOGXMLElement using the foreach, I get the following error -
http://www-apps.us.oracle.com:1100/~rvishnuv/transform1_error.gif
Let us say my X_TEST_TBL contians two records and X_TEST_TBL1 contains one record. Is there any way that I can use these two out parameters to map to the same destination (GLOGXMLElement) so that my final document contains multiple "GLOGXMLElement"s that represents data from both the output parameters? i.e. there should be in total of three occurances of GLOGXMLelement in the output document such that two occurances correspond to data obtained from X_TEST_TBL and one corresponds to data from X_TEST_TBL1.
Please let me know if there is any way to achieve this.
Thanks
Ravi

Is the listed $200 credit towards a trade-in on top of the original trade in value of a phone, or the maximum amount?

Question regarding the pen tool (w/ picture inside)

Hello everyone! I have a question regarding the pen tool. I think this picture is very helpful for my question:
So in this pic is an orange rectangle and within that rectangle is a blue stripe. I would like the blue stripe to be perfectly flush (not over, and not under) the edge of the rectangle. For example, on the bottom end of the blue stripe, you can clearly see that the stripe does not extend far enough to the edge of the orange rectangle. At the top of the stripe, it goes a little bit over (a bit hard to see). I work with some complex shapes when using the pen tool and it is really slowing me down to compensate for over/under shapes. If it could just snap to the borders of other shapes it would make my life a lot easier. Thanks for reading and please help!

A couple of thoughts come to mind:
1. You could create the shape "face on", using guides, and the points will snap to guides with snap enabled. Then you could transform the whole thing together by selecting all the shape layers.
2. Holding down the shift key while dragging a point seems to cause it to snap to some things under some conditions. However, on having just tried to recreate what you're showing I didn't see the proper snap happening sometimes.
3. There's the full manual approach, of course where you zoom into thousands of percent and move the points by hand manually. I assume this is what you're trying to avoid.
-Noel

Question regarding the use of Cisco Aironet 1140 series

Similar Messages

Maybe you are looking for