Question related to SFP, Fiber, and switches model Compatibility for Gigs Connections

Hi everyone,
I am in the middle of a project where we are receiving a 2gig Internet connection from a service provider. I need to connect this to a switch , my question is related to what sfp, switch would be the most compatible. I was thinking about a 3750 switch with sfp modules, but i am not sure if a SFP 1000 sx is enough as we are receiving a 2 gig connection via fiber then I would need to use a 10G module, with 10G sfps... mm well i am very confuse... can anyone help me please in your experience with a similar situation
Thanks.

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
A "2 gig" connection might mean a 10g logically limited to 2g, or it might mean the full duplex capacity of a gig link.
The SFP+ ports on 10g 3750X modules will support either a gig or 10g transceiver. The SPF ports, on either 10g or gig modules will only support gig.

Similar Messages

Windows 7 and OSI model compatibility

Dear Community
Very kindly pleasant about information in theme Windows 7 and OSI model compatiblity
http://support.microsoft.com/kb/103884 ; Is this a same model in both examples ?

This forum is for helping visitors in writing software that interacts with Windows's user interface (namely Windows Explorer).
I suggest you to get a TCP/IP book if you want to know how this model is applied on networking.
Visual C++ MVP

Eeprom address and caldacs model/address for pci-6014 and pci-6733

I have one pci-6014 and one pci-6733.
I need to transfer the calibration constants from eeprom to caldacs.
I search the adrress of the constants in the eeprom and the model and address of che caldacs.
Tanks

Hello,
It seems to be a common mode voltage or ground loop problem.
When you are sourcing an output signal from your DAQ board, the signal is already grounded, it means that it has already a reference. If you measure this output with a measurement device, which has also a ground, the both ground potential are not necessary equal. This difference is the common mode voltage and influences your measurement (offset).
Please check the following links to have more detail about grounded signal.
http://zone.ni.com/devzone/conceptd.nsf/webmain/8D907374C5E867F186256C640059F30C?opendocument
http://digital.ni.com/worldwide/france.nsf/webtechsupp/0E6A8D5999CEE1AF8025683C0056A4B1?OpenDocument&node=163080_f
Best regards,
Alexandre D
National Instruments

How to disable SSLv3 and keep only TLS for LDAP connection.

Hi,
I'm planning to keep only TLSv1.2 for LDAP connections.
I tried to set LDAP_OPT_SSL_INFO in LDAP Session Options using a SecPkgContext_ConnectionInfo Structure with dwProtocol SP_PROT_TLS1_2_CLIENT(as described here - https://social.msdn.microsoft.com/Forums/en-US/7544226d-97e1-4dae-a377-e382c2281e91/how-to-set-up-tls-in-ldap-connection?forum=vcgeneral),
but it returns LDAP_PARAM_ERROR.
I tried to call this function directly after ldap_sslinit/ldap_init and before ldap_connect() - without success, I tried to use other parameters with default values, I tried to initialize them by 0/other possible values - and also no success.
How I can do this?
Thanks for your advices.

LDAP_PARAM_ERROR
https://msdn.microsoft.com/en-us/library/aa367026(v=vs.85).aspx

Question about Wi-Fi led and switch of Portege Z930

Hi folks,
I'm not sure about my configuration: could anyone confirm that the wifi led near the touchpad is the only led of amber color?
Moreover, my F8 button for the wifi switch does not work: anyone knows which is the relative package?
Thanks
da

Hi
There is a row of indicators under the touchpad buttons.
The 3rd from right indicator is Wlan led.
The 2nd from right is WAN/WiMAX led.
The Wlan indicator glows orange if the WLan in ON
WAN/WiMAX indicator glows blue if its ON. In some models the indicator will glow and blink in order to indicate the connections status of the WAN function
To enable the WLan, you have to press FN + F8.
But if no Wlan device is installed, no dialog will appear

2 questions: default to shared folder and switcher sort order

I've got two Finder questions to which I haven't found an answer:
1) Can the "Finder>Preferences>General>New Finder windows open" option ever be set to a folder on a file server? When I try to do this, I can select the shared folder, but the pop-up menu reverts to the previous selection (e.g. Home). I suspect that since a server cannot be guaranteed to be accessible, the Finder refuses to allow it to be assigned as a default location.
2) I've got a switcher friend who would like to replicate in Finder windows the Windows Explorer behavior of sorting all folders to the top of the list. Is there a utility that will do this? List View sorted by Kind works for this chap only if there are no items with a Kind of alias, application, etc. that will sort higher than "Folder".

1) the answer appears to be yes but if you ever try to open a new window when the server isn't available the preference reverts to your computer.
2) no, at this time there is no Finder pref nor utility that sorts folders to the top. Two solutions exist but both are kludges. First, name every folder with a leading space, this forces the sort to the top. Second, PathFinder is a Finder semi-replacement which does allow the option of sorting folders to the top. PF is an interesting product but because it doesn't have all of Finder's AppleScript behaviors it cannot perfectly replace the Finder and having, in effect, two Finders is annoying.

Visual Hub questions (related to Apple TV) and others

Hey guys,
Just bought Visual Hub to convert my stuff.
What do you recommend for the settings ?
Right now this is what I use : (NOTE : I translated on the fly from french so maybe it's a bit different)
-To : iTunes
-Optimize for : Apple TV 5.1
-Quality : BIG QUESTION HERE : I want as close as 1080p as can be, but if the source file I'm -converting is poor quality, won't this make a big file for nothing ? What should I base my choice on?
-H.264 enabled
-In advanced, I select double-pass and deinterlace, audio settings = initial
Nothing else is tweaked in advanced
so what do you think ?
I have a couple of other questions :
- What if I deinterlace a video that is not interlaced in the beginning ?
- How can I determine if a video is interlaced ?
- How can I tell if a video is in 5.1 or even full HD ?
- How can I make sure to get 5.1 on my Apple TV
- Can Apple TV play 1080p ? or is it just upscaling ?
- If A TV can output 1080p, where can I find sources file of such quality ?
Anything else that I should know of related to my questions ?
Thanks guys !!

I don't use visualhub so I couldn't suggest settings for you, but.
but if the source file I'm -converting is poor quality, won't this make a big file for nothing
Yes, that's all it will do.
What if I deinterlace a video that is not interlaced in the beginning ?
You will lose detail
How can I determine if a video is interlaced ?
Take a look at it on a progressive scan display such as your mac monitor, you will see horizontal lines in high motion areas when paused.
How can I tell if a video is in 5.1 or even full HD ?
See This
How can I make sure to get 5.1 on my Apple TV
Your content file need to have an AC3 track and you will need to play the audio through a 5.1 capable receiver or home theatre system.
Can Apple TV play 1080p ? or is it just upscaling ?
It can play up to 720p after which it upscales.
If A TV can output 1080p, where can I find sources file of such quality ?
More or less nowhere.

Question related to FI-AA and FI-GL

Hi,
Below is the interview question asked when i was taking the interview. I couldn't answer this questions. If any of you have been working in FI-Asset and FI-GL can you please shed some light on this. I will definetely assing full points
What is FI-Asset Accounting mean to you?
What is Business value it adds?
Why business looking for this data?
Why kind of Key performance indicates involved in this?
What report you produced out of this data?
How does Delta Supported in this extraction?
What R/3 Tables involved in this extraction?
Write down the implementation steps for data extraction?
Ø       What is GL Accounting mean to you?
Ø       What is Business value it adds?
Ø       Why business looking for this data?
Ø       Why kind of Key performance indicates involved in this?
Ø       What report you produced out of this data?
Ø       How does Delta Supported in this extraction?
Ø       What R/3 Tables involved in this extraction?
Ø       Write down the implementation steps for data extraction?

Hi Lyubomir,
Thanks for your helpful replies.
I am not able to get what you were trying to say here :"it is important for SAP to know what is the beginning balance for 2006 and how the values have changed during between 01.01. and 30.09."
The fiscal year variant is V3 i.e april to march. So the start of year is 1.4.2006. and take over date is 30.09.2006.
and the last depreciation psoted date was set as 2006 / 06 . i.e september 2006.
In AS92 the asset values are split up as follows
Book value
Accumulated dep'n upto 31.03.2006
Current year dep'n from 1.4.2006 to 30.09.2006
When I look at the asset accounts GL balances it is same as the asset reports.
In my case heer what is the best approach to load the legacy data?
also when I run ABST2 the package is taken as 39 and phase as ANALYSE.
But the system shows as " List contains no data"
Are any patches to be updated?
Thanks,
Shyam

Question relating to Java printing and where to post...

First of all I am not a developer, but I have a question regarding printing in an application that was developed using Java and am not sure where to post it. I'll pose the question than defer to a moderator to move it if necessary.
Here's the issue and question:
We are using an application that has a host/client structure on several systems that use Windows Vista and XP. I have been told by the support team for this application that they use Java for printing tasks. I don't know if the entire application or just the print engine were developed in Java.
Here's the problem:
Whenever I tell this app to print for the FIRST time after opening the app, it takes between 4 and 5 minutes before it brings up the print menu. Again, this ONLY happens the FIRST time I tell it to print, and subsequent print commands are processed in a more normal timeframe.
If I close this app and immediatly open it again, it goes through the same silly wait time for the FIRST print only.
Tech support had me update Java to the latest incarnation on all machines, but that changed nothing. The guy even had the GALL to blame Java for the issue, can you believe that???
Anyway, my question to you people here - that develop with Java - is what in the world this app ( and I suppose Java ) could possibly be doing with this print job for 4 to 5 minutes?
BTW... these are NEW systems, with Dual-Core processors and a minimum of 1.5 gigs ( the server has 3 gigs) of RAM. Oh, and what I am printing is simply text, no graphics, just plain simple text.
Any and all comments/suggestions appreciated...
bob

Thx ChuckBing,
I agree with you about the application being the most logical source of the problem, and I have already provided their support with all the details that you suggest.
I'll look at the link you provided and see if anything there steers me in a direction....
bob

Question related to POF configuration and use-subclasses

Hi,
I noticed that the default POF configuration in coherence.jar (coherence-pof-config.xml) forces the use-subclasses flag to true (the ultimate use-subclasses value is true if whichever loaded POF configuration file specifies it to be true), and thus making it impossible to get error messages if a certain subclass of a registered type is not registered specifically in the POF-configuration, and users may silently lose data this way.
My question is:
Is the use-subclasses flag in the coherence-pof-config.xml set to true only because of Throwable-s, or are there other Coherence-provided classes which are serialized by subclass resolution and thus depend on the use-subclasses flag being true?
If only the Throwable-s depend on that, then instead of setting it to true, we can set it to false and use the following class instead of ConfigurablePofContext as the Serializer class for the POF-enabled services:
import com.tangosol.io.pof.ConfigurablePofContext;
import com.tangosol.run.xml.XmlElement;
* This class extends ConfigurablePofContext with the possibility to
* configurably disable the subclass-allowed setting forced true in the
* coherence-pof-config.xml, and still be able to use ThrowablePofSerializer for
* each not specifically configured Throwable subclass.
* @author Robert Varga
public class ThrowableAwareConfigurablePofContext extends
      ConfigurablePofContext {
    * By setting this flag to true, it is possible to disable subclass
    * resolution. Interface resolution remains untouched.
   private boolean m_fDisableSubclassAllowed;
    * {@inheritDoc}
   public ThrowableAwareConfigurablePofContext() {
    * {@inheritDoc}
    * @param sLocator
   public ThrowableAwareConfigurablePofContext(String sLocator) {
      super(sLocator);
    * {@inheritDoc}
    * @param xml
   public ThrowableAwareConfigurablePofContext(XmlElement xml) {
      super(xml);
    * Sets the {@link #m_fDisableSubclassAllowed} flag. You can set this as an
    * <init-param> in the Coherence cache configuration file.
    * @param disableSubclassAllowed
   public void setDisableSubclassAllowed(boolean disableSubclassAllowed) {
      this.m_fDisableSubclassAllowed = disableSubclassAllowed;
    * @return false if disableSubclassAllowed is true, or result from the super
    *         implementation otherwise.
   @Override
   protected boolean isSubclassAllowed() {
      return (!m_fDisableSubclassAllowed) && super.isSubclassAllowed();
    * If the super implementation could not resolve the type id for the class,
    * and subclass-allowed is disabled and clz is a {@link java.lang.Throwable}
    * subclass then it falls back to the configuration for
    * {@link java.lang.Throwable}.
   @Override
   protected int getInheritedUserTypeIdentifier(Class clz) {
      int result = super.getInheritedUserTypeIdentifier(clz);
      if (result == -1 && !isSubclassAllowed()
            && Throwable.class.isAssignableFrom(clz)) {
         result = getUserTypeIdentifier(Throwable.class);
      return result;
}Thanks and best regards,
Robert

dcarrano wrote:
Hi Robert,
If you are only interested in Java you are correct.
If you need more detail please let me know but I hope this answers your question.
Best regards,
-DaveHi Dave,
I am also interested in other environments, so I need more detail.
I am looking at the portability of my POF Serializer generator in which I assume that use-subclasses is false, because supporting use-subclasses being true would be quite hard to define, not to mention implement.
Thanks and best regards,
Robert

A few general questions relating to H55-GD65 and core i5 750 Lynnfield

I finally made the jump from AMD to intel, and DDR3 ram, been reading the forums for around 3hours, been a member for 2hrs. Been building systems since Redhat 9.0 came out, so Don't expect any thing as funny as Quote
because I want to know the temperature of the IOH without the heatsink.
Would it be better to run 2gig X 4 = 8gigs of RAM, or 4gigs X4 = 16 gigs?
Concerning dual channel mode, must I buy them in matched sets, or can I buy one stick at a time, obviously buying the same exact kind each time?
To run DDR3 1600mhz on this board will I need to set the voltage/timings manually, or will it auto detect?
From what I've read the pcie controller is on die, and with the i5's you can only run 1@ X16 or dual X8, am I correct?
If I get a pcie x8 sas raid controller card, will it affect graphics performance?
Also this will be my first attempt at dual booting sata hard drives.
Would it be difficult to have win7 x64 on the mobo's onboard sata, and linux (either Mandriva, Open Suse, or gentoo if my insomnia is still acting up)
on the sas card?
Edit: Almost forgot, has any one else had issues with the onboard NIC dropping connection? It never happens when It is in use, only when i walk away from it, as an example Wow's latest 4gig patch had 900megs to go on a 1.1megabyte connection, upon going to sleep and locking the computer windows key-L, woke up with it having 500megs remaining and as soon as i opened my browser my connection picked right back up

Hello and welcome,
Quote
Would it be better to run 2gig X 4 = 8gigs of RAM, or 4gigs X4 = 16 gigs?
Concerning dual channel mode, must I buy them in matched sets, or can I buy one stick at a time, obviously buying the same exact kind each time?
To run DDR3 1600mhz on this board will I need to set the voltage/timings manually, or will it auto detect?
Its better to use 2x4GB, to lessen the strain on the memorycontroller and yes, you'll have to set it to 1600MHz yourself most of the time.
The memorycontroller is rated for 1066/1333MHz, so anything beyond is considered overclocking and thus the controller will not set those higher timings automatically.
Do you really need 8GB? For office, internet and gaming, normal homeusage, 4GB is more then enough, 8GB is nice if you render a lot or if you use cad/cam and photoshop stuff
Quote
From what I've read the pcie controller is on die, and with the i5's you can only run 1@ X16 or dual X8, am I correct?
If I get a pcie x8 sas raid controller card, will it affect graphics performance?
Yes it runs @x8 when running 2 vga's, or in your case if you use a PCIe x8 card, but the impact is none, even the GTX480 and the HD5970 are not capped when @x8, so no worries there.
Quote
Would it be difficult to have win7 x64 on the mobo's onboard sata, and linux (either Mandriva, Open Suse, or gentoo if my insomnia is still acting up)
on the sas card?
I have had dual and even triple boot since XP and never had any issues, be sure to write the different os to different hd's or partitions. About Linux on a sascard, no idea, Im not familiar with that.
Quote
Edit: Almost forgot, has any one else had issues with the onboard NIC dropping connection? It never happens when It is in use, only when i walk away from it, as an example Wow's latest 4gig patch had 900megs to go on a 1.1megabyte connection, upon going to sleep and locking the computer windows key-L, woke up with it having 500megs remaining and as soon as i opened my browser my connection picked right back up
Check your windows powersavings settings, maybe it turns it off when in standby/sleep mode.
If you cant find anything there check bios, to make sure onboard NIC is always on, although I believe you must find such a setting in windows.

Hi guys! I have a question related to the latest version of iMovie. For some reason, when I drag a video file to my project, the audio becomes slightly higher pitched. Any suggestions on how to avoid this? Thanks!

This is iMovie 10 I believe. Thanks again!! Really appreciate the help!

To do this in iMovie 11. use the SHARE menu. Share your project using the Share menu and choose Export Using QuickTime.
In the Dialog box that comes up, choose Sound to AIFF, or one of the other sound options. This will create a file that you can drag into iTubes.

Two Questions. How to clean and a speech tool for PDF's online with my Mac

Hello,
I watch a lot of videos and movies on YouTube and also listen to a lot of audio recordings and use the txt to speech to read websites. Do you know if I need to be concerned about cleaning my mac at some time, and how would I do that? Don't want to download something that might hurt my mac.
I have a 2008 quad 4 Mac Pro Desktop OS X 10.9.2
Also is there a too I can get for my computer to read PDF's on websites or even a PDF document for me on a Mac?
Thank you for any help I can get

sorry the last paragraph should read" Is there a tool like text to speech so the computer can read PDF on a Mac?
thanks again

I want to acheive digitally triggered data acquisition and using AIO lines for triggering connecting to PFI lines but no response.

How to acheive digital data acquisitions using AO signals as trigger signal.

Greetings,
I am not sure that I have a clear understanding of your question. It appears that you want to perform a triggered acquisition. You mentioned both analog input (AI) and analog output (AO). Which type of operation are you performing? Are you using digital or analog triggering? Also, it would be helpful if you could mention what hardware and software you are using.
Spencer S.

Powerbook G4 and Apple TV fighting for AE Connection

I've been running my old Powerbook G4 off my Airport Extreme for years with no problem. When I bought my new Apple TV and hooked it up to the AE wireless network, things went great for about a week.
Now the Apple TV loses the network connection, I think because it and the Powerbook are receiving the same DHCP IP address from the AE. The Powerbook G4 trumps the Apple TV every time, and the only way I can reconnect the Apple TV is to put the Powerbook to sleep, reconnect the Apple TV to the network, and THEN start the Powerbook up again.
This holds out for another few days, until the problem re-occurs.
I am NOT distributing IP addresses on the Airport Express, and instead use a Linksys router to do all the NAT and DHCP work. Is this the problem?
[Cable Modem] -> [Linksys] -> [Airport Express]
Thanks!

Hi Jimmy, unfortunately I can't offer any help because I have similar problems. Maybe interference is the source of your issues but it's not for me. I literally live in woods with few neiggbors.
I purchased an ATV last week and will be returning it over the weekend. It is nothing but a headache. It does not run transparently. Heck, most of the time it just doesn't work. Sometimes it connects to home sharing but then won't find movies. Sometimes it doesn't find the other computers even though home sharing is on. Sometimes it accesses the computers but won't allow the selected movie to play. Rebooting sometimes helps but only for a short while.
A couple of weeks ago I purchased a Time Capsule and my general sense is that my overall network capabilities, both WiFi and outside, is degaraded. Things are so **** fussy. They worked much better with my four year old router. But no, I let my self be seduced by the shiny new stuff.
Beteween ATV and Time Capsule it's driving me crazy. I just want things to work. I'm comming to the conclusion that Apple really doesn't know how to do networking. I know I don't once it's past the plug-it-in stage and choosing a few settings. The plug it in and things will work concept is just that, an unrealized concept.
Sorry to take my frustration out on you.

Question related to SFP, Fiber, and switches model Compatibility for Gigs Connections

Similar Messages

Maybe you are looking for